Skip to Content

Changes for page 1 Communication

Last modified by Hunter on 2024/07/01 10:54
From version 66.1
edited by Ben
on 2022/08/24 11:59
Change comment: There is no comment for this version
To version 81.1
edited by Ben
on 2022/08/24 15:23
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -4,7 +4,7 @@
4 4  
5 5  Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
6 6  
7 -**HMI Settings**
7 +**1）PLC Settings**
8 8  
9 9  |**Item**|**Settings**|**Note**
10 10  |Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
... ... @@ -15,7 +15,7 @@
15 15  |Stop bit|1|
16 16  |PLC station No.|1|
17 17  
18 -**Address List**
18 +**2）Address List**
19 19  
20 20  |**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
21 21  |(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
... ... @@ -33,16 +33,20 @@
33 33  |S|S|S d|0~~99999|
34 34  |SD|SD|SD d|8000~~9999|
35 35  
36 -**Cable Wiring**
36 +**3）Set communication Protocol**
37 37  
38 -* **RS485**
38 +[[image:image-20220824152217-1.png]]
39 39  
40 - [[image:image-20220822172124-1.png]]
40 +**4）Cable Wiring**
41 41  
42 42  * **RS422**
43 43  
44 - [[image:image-20220822172228-2.png]]
44 + [[image:image-20220824120614-5.png]]
45 45  
46 +* **RS485**
47 +
48 + [[image:image-20220824120524-3.png]]
49 +
46 46  == **LX5V Serial Protocol** ==
47 47  
48 48  This example introduces the establishment of serial port communication between Wecon V-BOX and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
... ... @@ -51,7 +51,7 @@
51 51  
52 52  **1）PLC programming software**
53 53  
54 -[[image:image-20220822172553-1.png]]
58 +[[image:image-20220824142722-1.png]]
55 55  
56 56  **2）New PLC project**
57 57  
... ... @@ -89,7 +89,6 @@
89 89  
90 90  [[image:image-20220824104909-2.png]]
91 91  
92 -
93 93  **3）Set communication port parameters**
94 94  
95 95  Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
... ... @@ -102,38 +102,33 @@
102 102  
103 103  Parity：No verification
104 104  
105 -[[image:image-20220811104012-1.png]]
108 +[[image:image-20220824142130-1.png]]
106 106  
107 -
108 108  **hardware connection**
109 109  
110 110  **1）Hardware wiring diagram**
111 111  
112 -This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
114 +[[image:image-20220824142546-2.png]]
113 113  
116 +[[image:image-20220824142643-3.png]]
114 114  
118 +The above are all the steps for establishing serial port communication between V-BOX with LX5V PLC.
115 115  
116 -[[image:image-20220811103005-4.png]]
117 -
118 -[[image:image-20220811103227-7.png]]
119 -
120 -The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
121 -
122 122  == **LX5V-N Ethernet protocol** ==
123 123  
124 - This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
122 +This example introduces the establishment of Ethernet communication between V-BOX and LX5V-N. It is introduced through three parts: PLC software configuration, V-BOX software configuration, and hardware wiring.
125 125  
126 126  **Software configuration of PLC**
127 127  
128 128  **1）PLC programming software**
129 129  
130 -[[image:image-20220810164710-1.png]]
128 +[[image:image-20220824142722-1.png]]
131 131  
132 132  **2）New PLC project**
133 133  
134 134  Click New Project and select the PLC model.
135 135  
136 -[[image:image-20220811115454-1.png]]
134 +[[image:image-20220824143613-1.png]]
137 137  
138 138  **3）Set Ethernet port parameters**
139 139  
... ... @@ -145,53 +145,38 @@
145 145  
146 146  subnet mask：255.255.255.0
147 147  
148 -[[image:image-20220811140530-2.png]]
146 +[[image:image-20220824143744-2.png]]
149 149  
150 150  **4）Registers list**
151 151  
152 -[[image:image-20220811102219-3.png]]
150 +[[image:image-20220822172730-4.png]]
153 153  
154 -**HMI software configuration**
152 +(% id="cke_bm_22473S" style="display:none" %)** **(%%)**V-BOX software configuration**
155 155  
156 -**1）HMI programming software**
154 +**1）V-BOX programming software**
157 157  
158 - [[image:image-20220810171237-4.png]]
156 + [[image:image-20220824104124-1.png]]
159 159  
160 -**2）New HMI project**
158 +**2）V-NET add device**
161 161  
162 -Click New Project and select the HMI model.
160 +Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
163 163  
164 -[[image:image-20220810172010-5.png]]
162 +[[image:image-20220824104909-2.png]]
165 165  
166 -**3）Set communication port parameters**
164 +**3）Set communication Protocol**
167 167  
168 -Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
166 +Click Communication to configure the LX5V plc protocol and IP address.
169 169  
170 -HMI IP address：192.168.39.201
168 +[[image:image-20220824144619-1.png]]
171 171  
172 -default gateway：192.168.39.1
173 -
174 -subnet mask：255.255.255.0
175 -
176 -[[image:image-20220811170753-2.png]]
177 -
178 -Next, click Communication Settings to configure the IP of the HMI communication object.
179 -
180 -[[image:image-20220811163047-1.png]]
181 -
182 182  **hardware connection**
183 183  
184 184  **1）Hardware wiring diagram**
185 185  
186 -This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
174 +[[image:image-20220824151127-2.png]]
187 187  
188 -[[image:image-20220811170248-1.png]]
176 +The above are all the steps for establishing ethernet communication between V-BOX with LX5V PLC.
189 189  
190 -The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
191 -
192 -(% style="text-align:center" %)
193 -[[image:1624348978863-771.png||queryString="width=812&height=494" height="487" width="800" class="img-thumbnail"]]
194 -
195 195  = **Rockwell PLC** =
196 196  
197 197  == (% id="cke_bm_5621S" style="display:none" %)** **(%%)**MicroLogix Protocol** ==
image-20220824120406-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +31.9 KB
Content
image-20220824120507-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +10.3 KB
Content
image-20220824120524-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +23.4 KB
Content
image-20220824120547-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +49.2 KB
Content
image-20220824120614-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +30.9 KB
Content
image-20220824142130-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +122.2 KB
Content
image-20220824142546-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +111.2 KB
Content
image-20220824142643-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +38.3 KB
Content
image-20220824142722-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +7.3 KB
Content
image-20220824143613-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +206.2 KB
Content
image-20220824143744-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +126.0 KB
Content
image-20220824144619-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +126.2 KB
Content
image-20220824151127-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +85.5 KB
Content
image-20220824152217-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Ben
Size
... ... @@ -1,0 +1,1 @@
1 +123.6 KB
Content