Wiki source code of 1 Communication

Version 143.1 by Ben on 2022/08/31 16:10

version	line-number	content
136.1	1	= Create communication with WECON PLC =
1.1	2
123.1	3	== LX3V Serial Protocol ==
31.1	4
123.1	5	Supported series: Wecon LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
1.1	6
123.1	7	1）V-BOX setting
1.1	8
123.1	9	\|Item\|Settings\|Note
	10	\|Protocol\|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM\|
	11	\|Connection\|RS422/RS485\|
	12	\|Baud rate\|9600\|
	13	\|Data bit\|7\|
	14	\|Parity\|EVEN\|
	15	\|Stop bit\|1\|
	16	\|PLC station No.\|1\|
1.1	17
123.1	18	2）Address List
20.1	19
125.1	20
	21	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	22	\|(% rowspan="6" %)Bit\|X\|X\|Xo\|0~~303237\|
119.1	23	\|Y\|Y\|Y o\|0~~303237\|
	24	\|M\|M\|M d\|0~~99999\|
125.1	25	\|T\|T\|T d\|0~~99999\|
	26	\|C\|C\|C d\|0~~99999\|
	27	\|S\|S\|S d\|0~~99999\|
	28	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
119.1	29	\|Y\|Y\|Y o\|0~~303237\|
	30	\|M\|M\|M d\|0~~99999\|
125.1	31	\|T\|T\|T d\|0~~99999\|
	32	\|C\|C\|C d\|0~~199\|
	33	\|D\|D\|D d\|0~~7999\|
	34	\|S\|S\|S d\|0~~99999\|
	35	\|SD\|SD\|SD d\|8000~~9999\|
20.1	36
123.1	37	3）Configure the communication protocol
20.1	38
119.1	39	[[image:image-20220824152217-1.png\|\|alt="图片-20220824152217-1.png"]]
80.1	40
123.1	41	4）Cable Wiring
80.1	42
119.1	43	* RS422
20.1	44
119.1	45	[[image:image-20220824120614-5.png]]
20.1	46
119.1	47	* RS485
68.1	48
119.1	49	[[image:image-20220824120524-3.png]]
68.1	50
119.1	51	== LX5V Serial Protocol ==
28.1	52
84.1	53	This example introduces the establishment of serial port communication between V-BOX and LX5V. It is introduced through three parts: PLC software configuration, V-BOX software configuration, and hardware wiring.
20.1	54
119.1	55	Software configuration of PLC
20.1	56
119.1	57	1）PLC programming software
20.1	58
119.1	59	[[image:image-20220824142722-1.png]]
20.1	60
119.1	61	2）New PLC project
20.1	62
	63	Click New Project and select the PLC model.
	64
119.1	65	[[image:image-20220822172623-2.png]]
20.1	66
119.1	67	3）Set Serial port parameters
20.1	68
	69	Follow the steps below to configure Serial port parameters
	70
	71	Baud rate：115200
	72
	73	Data bit：8
	74
	75	Stop bit：1
	76
	77	Parity：No verification
	78
119.1	79	[[image:image-20220822172657-3.png]]
20.1	80
119.1	81	4）Registers list
20.1	82
119.1	83	[[image:image-20220822172730-4.png]]
20.1	84
119.1	85	V-BOX software configuration
28.1	86
119.1	87	1）V-BOX programming software
20.1	88
119.1	89	[[image:image-20220824104124-1.png]]
20.1	90
119.1	91	2）V-NET add device
20.1	92
35.1	93	Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
20.1	94
119.1	95	[[image:image-20220824104909-2.png]]
20.1	96
119.1	97	3）Set communication port parameters
20.1	98
	99	Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
	100
	101	Baud rate：115200
	102
	103	Data bit：8
	104
	105	Stop bit：1
	106
	107	Parity：No verification
	108
119.1	109	[[image:image-20220824142130-1.png]]
20.1	110
119.1	111	hardware connection
20.1	112
119.1	113	1）Hardware wiring diagram
20.1	114
119.1	115	[[image:image-20220824142546-2.png]]
28.1	116
119.1	117	[[image:image-20220824142643-3.png]]
28.1	118
74.1	119	The above are all the steps for establishing serial port communication between V-BOX with LX5V PLC.
20.1	120
119.1	121	== LX5V-N Ethernet protocol ==
20.1	122
77.1	123	This example introduces the establishment of Ethernet communication between V-BOX and LX5V-N. It is introduced through three parts: PLC software configuration, V-BOX software configuration, and hardware wiring.
20.1	124
119.1	125	Software configuration of PLC
20.1	126
119.1	127	1）PLC programming software
20.1	128
119.1	129	[[image:image-20220824142722-1.png]]
20.1	130
119.1	131	2）New PLC project
20.1	132
	133	Click New Project and select the PLC model.
	134
119.1	135	[[image:image-20220824143613-1.png]]
20.1	136
119.1	137	3）Set Ethernet port parameters
20.1	138
	139	Follow the steps below to configure Ethernet parameters
	140
	141	PLC IP address：192.168.39.200
	142
	143	default gateway：192.168.39.1
	144
	145	subnet mask：255.255.255.0
	146
119.1	147	[[image:image-20220824143744-2.png]]
20.1	148
119.1	149	4）Registers list
20.1	150
119.1	151	[[image:image-20220822172730-4.png]]
20.1	152
119.1	153	(% id="cke_bm_22473S" style="display:none" %) (%%)V-BOX software configuration
20.1	154
119.1	155	1）V-BOX programming software
20.1	156
119.1	157	[[image:image-20220824104124-1.png]]
20.1	158
119.1	159	2）V-NET add device
20.1	160
74.1	161	Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
20.1	162
119.1	163	[[image:image-20220824104909-2.png]]
20.1	164
119.1	165	3）Set communication Protocol
20.1	166
74.1	167	Click Communication to configure the LX5V plc protocol and IP address.
20.1	168
119.1	169	[[image:image-20220824144619-1.png]]
20.1	170
119.1	171	hardware connection
20.1	172
119.1	173	1）Hardware wiring diagram
20.1	174
119.1	175	[[image:image-20220824151127-2.png]]
20.1	176
74.1	177	The above are all the steps for establishing ethernet communication between V-BOX with LX5V PLC.
20.1	178
137.1	179	= Create communication with Rockwell PLC =
22.1	180
119.1	181	== (% id="cke_bm_5621S" style="display:none" %) (%%)MicroLogix Protocol ==
37.1	182
	183	MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
	184
119.1	185	1）PLC Settings
37.1	186
119.1	187	\|Item\|Settings\|Note
	188	\|Protocol\|Allen-Bradlley DF1 Advanced\|
	189	\|Connection\|RS232\|
	190	\|Baud rate\|19200\|
	191	\|Data bit\|8\|
	192	\|Parity\|None\|
	193	\|Stop bit\|1\|
	194	\|PLC station No.\|1\|
37.1	195
119.1	196	2）Address List
37.1	197
119.1	198	\|Type\|Device registers\|Format\|Range\|Note
	199	\|(% rowspan="5" %)Bit\|I\|I d.d\|0.0~~255.15\|
	200	\|O\|O d.d\|0.0~~255.15\|
	201	\|B\|B nnhh.dd\|0.0~~ffff.15\|nn: block number (hex)
	202	\|S\|S d.d\|0.0~~255.15\|
	203	\|N\|N nnhh.dd\|0.0~~ffff.15\|nn: block number (hex)
	204	\|(% rowspan="9" %)Word\|S\|S d\|0~~255\|
	205	\|TS\|TS nnhh\|0~~ffff\|(% rowspan="8" %)nn: block number (hex)
	206	\|TP\|TP nnhh\|0~~ffff
	207	\|CS\|CS nnhh\|0~~ffff
	208	\|CP\|CP nnhh\|0~~ffff
	209	\|N\|N nnhh\|0~~ffff
	210	\|C\|C nnhh\|0~~ffff
	211	\|T\|T nnhh\|0~~ffff
	212	\|R\|R nnhh\|0~~ffff
37.1	213
119.1	214	3）Configure the communication protocol[[image:image-20220824152928-1.png]]
85.1	215
119.1	216	4）Configure the communication protocol
37.1	217
119.1	218	[[image:image-20220824110724-1.png]]
37.1	219
139.1	220	== Micro850_FreeTag Protocol ==
37.1	221
11.1	222	(((
16.1	223	(((
38.1	224	This example introduces the establishment of Ethernet communication between Wecon V-box and CompactLogix L1769. It is introduced through three parts: PLC software configuration, V-box software configuration, and hardware wiring.
16.1	225	)))
11.1	226	)))
	227
	228	(((
15.1	229	(% class="wikigeneratedid" id="HSoftwareconfigurationofPLC" %)
	230	(((
119.1	231	Software configuration of PLC
11.1	232	)))
	233
15.1	234	(% class="wikigeneratedid" id="HPLCprogrammingsoftware" %)
11.1	235	(((
119.1	236	1）PLC programming software
15.1	237	)))
11.1	238
119.1	239	[[image:image-20220714162600-1.png]]
11.1	240
15.1	241	(% class="wikigeneratedid" id="HNewPLCproject" %)
11.1	242	(((
119.1	243	2）New PLC project
11.1	244	)))
	245
	246	(((
16.1	247	(((
15.1	248	Click New Project and select the PLC model.
11.1	249	)))
16.1	250	)))
11.1	251
	252	(((
119.1	253	[[image:image-20220714162617-2.png]]
11.1	254	)))
	255
	256	(((
17.1	257
16.1	258
119.1	259	[[image:image-20220714162652-4.png]]
11.1	260	)))
	261
	262	(((
15.1	263	(% class="wikigeneratedid" id="HSetEthernetparameters" %)
	264	(((
119.1	265	3）Set Ethernet parameters
15.1	266	)))
11.1	267
	268	(((
15.1	269	(((
16.1	270	(((
11.1	271	Follow the steps below to configure Ethernet parameters
	272	)))
15.1	273	)))
16.1	274	)))
11.1	275
	276	(((
15.1	277	(((
16.1	278	(((
11.1	279	PLC IP address：192.168.40.101
	280	)))
15.1	281	)))
16.1	282	)))
11.1	283
	284	(((
15.1	285	(((
16.1	286	(((
11.1	287	default gateway：192.168.40.1
	288	)))
15.1	289	)))
16.1	290	)))
11.1	291
	292	(((
15.1	293	(((
16.1	294	(((
11.1	295	subnet mask：255.255.255.0
	296	)))
15.1	297	)))
16.1	298	)))
11.1	299
	300	(((
119.1	301	[[image:image-20220714162713-5.png]]
11.1	302	)))
	303
	304	(((
	305
	306	)))
	307
	308	(((
15.1	309	(% class="wikigeneratedid" id="HV-boxsoftwareconfiguration" %)
	310	(((
119.1	311	V-box software configuration
15.1	312	)))
11.1	313
15.1	314	(% class="wikigeneratedid" id="HV-boxprogrammingsoftware" %)
	315	(((
119.1	316	1）V-box programming software
15.1	317	)))
11.1	318
15.1	319	(% class="wikigeneratedid" %)
	320	(((
119.1	321	[[image:image-20220714162725-6.png]]
15.1	322	)))
11.1	323
15.1	324	(% class="wikigeneratedid" id="HConfiguredevicenetwork" %)
	325	(((
119.1	326	2）Configure device network
15.1	327	)))
11.1	328
	329	(((
15.1	330	(((
16.1	331	(((
119.1	332	Click the Configuration Download button[[image:image-20220714115308-8.png\|\|height="22" width="15"]], It is used to configure the device network, update the device time, obtain the device machine code, check the device network, etc.
11.1	333	)))
16.1	334
	335	(((
	336	In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection
15.1	337	)))
16.1	338	)))
	339	)))
11.1	340
	341	(((
15.1	342	(((
119.1	343	[[image:image-20220714162737-7.png]]
16.1	344
	345
11.1	346	)))
	347	)))
	348	)))
	349	)))
	350
15.1	351	(% class="wikigeneratedid" id="HV-netadddevice" %)
11.1	352	(((
119.1	353	3）V-net add device
11.1	354	)))
15.1	355	)))
11.1	356
	357	(((
16.1	358	(((
119.1	359	Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device. [[image:image-20220714162752-8.png]]
11.1	360	)))
	361
	362
	363	)))
	364
	365	(((
15.1	366	(% class="wikigeneratedid" id="HSetcommunicationportparameters" %)
	367	(((
119.1	368	4）Set communication port parameters
15.1	369	)))
11.1	370
16.1	371	(((
	372	In the device list on the left, find the Vbox that communicates with the L1769, click it and select configuration,communication port configuration in the main interface to add a communication protocol.
11.1	373	)))
	374
119.1	375	[[image:image-20220714162805-9.png]]
16.1	376	)))
	377
	378	(((
11.1	379	The communication port is selected as Ethernet, the device type is selected as Allen-Bradley, the protocol is Allen-BradleyMicro850_FreeTag EthemetIP, and the IP is the internal IP address of the L1769 PLC. The port number is 44818.
16.1	380	)))
11.1	381
119.1	382	[[image:image-20220824164346-1.png]]
11.1	383
	384
16.1	385	(((
119.1	386	After adding the protocol Allen-BradleyMicro850_FreeTag, click[[image:image-20220714143838-2.png]]icon add label.[[image:image-20220714162827-11.png]]
16.1	387	)))
14.1	388
16.1	389	(% class="wikigeneratedid" id="HEngineeringproduction" %)
	390	(((
119.1	391	5）Engineering production
16.1	392	)))
14.1	393
16.1	394	(% class="wikigeneratedid" %)
	395	(((
	396	(((
	397	According to your own needs, use the V-NET client software to edit the required data monitoring points.
	398	)))
14.1	399
119.1	400	[[image:image-20220714162841-12.png]]
14.1	401
16.1	402
	403	(((
119.1	404	hardware connection
16.1	405	)))
	406	)))
	407
	408	(((
119.1	409	1）Hardware wiring diagram
16.1	410	)))
	411
	412	(((
	413	(((
	414	This example introduces Wecon V-box with Allen-Bradley L1769 PLC to establish communication through Ethernet. The connection diagram is as follows:
	415	)))
	416
119.1	417	[[image:image-20220714162856-13.png]]
16.1	418
	419	(((
41.1	420	The above are all the steps for establishing Ethernet communication between Wecon V-box with CompactLogix L1769 PLC.
26.1	421
	422
119.1	423	== Allen-Bradley Ethernet DF1 ==
26.1	424
119.1	425	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Allen-Bradley%20Ethernet%20DF1.zip]]
26.1	426
	427
138.1	428	= Create communication with Siemens PLC =
61.1	429
119.1	430	== S7-200 Smart Ethernet Protocol ==
61.1	431
119.1	432	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20S7-200%20Smart.zip]]
88.1	433
	434
119.1	435	== S7-300 Ethernet Protocol ==
88.1	436
	437	Supported Series: Siemens S7-300 series PLC
	438
119.1	439	1）PLC Setting
88.1	440
119.1	441	\|Items\|Settings\|Note
	442	\|Protocol\|Simens S7-300 Ethernet\|
	443	\|Connection\|Ethernet\|
	444	\|Port No.\|102\|
	445	\|PLC station No.\|2\|Need to be same as the PLC setting
88.1	446
119.1	447	2）Address List
88.1	448
119.1	449	\|Type\|Device register\|HMI register\|Format\|Range\|Note
	450	\|(% rowspan="4" %)Bit\|I\|I\|I ddddd.o\|0.0~~99999.7\|
	451	\|Q\|Q\|Q ddddd.o\|0.0~~99999.7\|
	452	\|M\|M\|M ddddd.o\|0.0~~99999.7\|
	453	\|DB0.DB~~DB99.DB\|DBxDBD\|DBxDB nndddd.o\|0.0~~99999999.7\|(((
88.1	454	nn: block number;
	455
	456	dddd: address;
16.1	457	)))
119.1	458	\|(% rowspan="8" %)Word\|I\|IW\|IW ddddd\|0~~99999\|
	459	\|Q\|QW\|QW ddddd\|0~~99999\|
	460	\|(% rowspan="3" %)M\|MB\|MB ddddd\|0~~99999\|
	461	\|MW\|MW ddddd\|0~~99999\|(((
88.1	462	MW0=MB(0~~1)
	463
	464	MW2=MB(2~~3)
	465
	466	Address value is a multiple of 2
16.1	467	)))
119.1	468	\|MD\|MD ddddd\|0~~99999\|(((
88.1	469	MD0=MB(0~~3)
16.1	470
88.1	471	MD4=MB(4~~7)
	472
	473	Address value is a multiple of 4
	474	)))
119.1	475	\|(% rowspan="3" %)DB0.DB~~DB99.DB\|DBxDBB\|DBxDBB nndddd\|0~~99999999\|(% rowspan="3" %)(((
88.1	476	nn: block number;
	477
	478	dddd: address
	479	)))
119.1	480	\|DBxDBW\|DBxDBW nndddd\|0~~99999999
	481	\|DBxDBD\|DBxDBD nndddd\|0~~99999999
88.1	482
119.1	483	3）Configure the communication protocol
88.1	484
119.1	485	[[image:image-20220824161345-1.png]]
88.1	486
119.1	487	4）Cable Wiring
88.1	488
119.1	489	[[image:image-20220824161450-2.png]]
88.1	490	)))
	491	)))
	492
119.1	493	== S7-1200 Ethernet Protocol ==
1.1	494
119.1	495	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20S7-1200%20via%20Ehernet.zip]]
1.1	496
119.1	497	== S7-XXX Ethernet Protocol ==
91.1	498
	499	Supported Series: Siemens S7-400, S7-1200 and S7-1500
	500
119.1	501	1）PLC Setting
91.1	502
119.1	503	\|=Items\|=Settings\|=Note
	504	\|Protocol\|Siemens S7-XXX\|
	505	\|Connection\|Ethernet\|
	506	\|Port No.\|102\|
	507	\|Device No.\|Slot (Default 1 for S7-1500/ 2 for S7-1200/ 3 for S7-400)\|
	508	\|HMI No.\|Rack (Default as 0)\|
91.1	509
94.1	510	Slot from TIA Portal is equal to Device No. of V-net
91.1	511
94.1	512	Rack from TIA Portal is equal to HMI No. of V-net
91.1	513
119.1	514	[[image:image-20220824162459-3.png]]
91.1	515
119.1	516	[[image:image-20220824163305-2.png]]
94.1	517
119.1	518	2）Address List
91.1	519
119.1	520	\|Type\|Device register\|HMI register\|Format\|Range\|Note
	521	\|(% rowspan="4" %)Bit\|I\|I\|M d.o\|(((
91.1	522	d:0~-~-9999
	523
	524	o:0-7
	525	)))\|
119.1	526	\|Q\|Q\|Q d.o\|(((
91.1	527	d:0~-~-9999
	528
	529	o:0-7
	530	)))\|
119.1	531	\|M\|M\|M d.o\|(((
91.1	532	d:0~-~-9999
	533
	534	o:0-7
	535	)))\|
119.1	536	\|DB0.DB-DB99.DB\|DBxDB\|DBxDBnndddd.o\|(((
91.1	537	nn:0-9999,
	538
	539	dddd:0-9999,
	540
	541	o:0-7
	542	)))\|(((
	543	nn:DB No.
	544
	545	dddd:address value
	546
	547	o: digit address
	548	)))
119.1	549	\|(% rowspan="8" %)Word\|M\|MB\|MB d\|d:0-99999\|
	550	\|M\|MW\|MW d\|d:0-99999\|(((
91.1	551	MW0=MB(0~~1)
	552
	553	MW2=MB(2~~3)
	554
	555	Address value is a multiple of 2
	556	)))
119.1	557	\|M\|MD\|MD d\|d:0-99999\|(((
91.1	558	MD0=MB(0~~3)
	559
	560	MD4=MB(4~~7)
	561
	562	Address value is a multiple of 4
	563	)))
119.1	564	\|I\|IW\|IW d\|d:0-99999\|
	565	\|Q\|QW\|QW d\|d:0-99999\|
	566	\|DB0.DB-DB99.DB\|DBxDBB\|DBxDBBnndddd\|(((
91.1	567	nn:0-9999
	568
	569	dddd:0-9999
	570	)))\|(((
	571	nn:DB No.
	572
	573	dddd:address value
	574	)))
119.1	575	\|DB0.DB-DB99.DB\|DBxDBW\|DBxDBWnndddd\|(((
91.1	576	nn:0-9999
	577
	578	dddd:0-9999
	579	)))\|(((
	580	nn:DB No.
	581
	582	dddd:address value
	583
	584	Address value is a multiple of 2
	585	)))
119.1	586	\|DB0.DB-DB99.DB\|DBxDBD\|DBxDBDnndddd\|(((
91.1	587	nn:0-9999
	588
	589	dddd:0-9999
	590	)))\|(((
	591	nn:DB No.
	592
	593	dddd:address value
	594
	595	Address value is a multiple of 4
	596	)))
	597
119.1	598	3）Configure the communication protocol
91.1	599
119.1	600	[[image:image-20220824163448-3.png]]
91.1	601
119.1	602	✎Note:
91.1	603
94.1	604	* The S7-1200 supports simultaneous connection of three devices, so the driver supports simultaneous access to PLC by three V-BOX.
	605	* V-BOX access PLC, use S7 protocol, access PLC TSAP 02.01 (s7-1200 PROFINET interface only supports three connections, the default support), detailed reference to the system manual of S7-1200.
91.1	606
119.1	607	4）Cable Wiring
91.1	608
119.1	609	[[image:image-20220824162342-2.png]]
91.1	610
138.1	611	= Create communication with Mitsubishi PLC =
56.1	612
119.1	613	== FX1S，1N，2N Serial Protocol ==
103.1	614
105.1	615	Supported Series: Mitsubishi FX1S, FX1N, FX2N series
103.1	616
119.1	617	1）V-BOX Settings
103.1	618
119.1	619	\|Item\|Settings\|Note
	620	\|Protocol\|Mitsubishi FX1S/FX1N/FX2N\|
	621	\|Connection\|RS422/RS485/RS232\|
	622	\|Baud rate\|9600~~115200\|
	623	\|Data bit\|7/8\|
	624	\|Parity\|EVEN/Odd/None\|
	625	\|Stop bit\|1/2\|
	626	\|PLC station No.\|1~~255\|
104.1	627
119.1	628	2）Address List
104.1	629
119.1	630	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	631	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	632	\|Y\|Y\|Y o\|0~~303237\|
	633	\|M\|M\|M d\|0~~99999\|
	634	\|T\|T\|T d\|0~~99999\|
	635	\|C\|C\|C d\|0~~99999\|
	636	\|S\|S\|S d\|0~~99999\|
	637	\|SM\|SM\|SM d\|8000~~9999\|
	638	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	639	\|Y\|Y\|Y o\|0~~303237\|
	640	\|M\|M\|M d\|0~~99999\|
	641	\|T\|T\|T d\|0~~99999\|
	642	\|C\|C\|C d\|0~~199\|
	643	\|D\|D\|D d\|0~~7999\|
	644	\|S\|S\|S d\|0~~99999\|
	645	\|SD\|SD\|SD d\|8000~~9999\|
104.1	646
119.1	647	3）Configure the communication protocol
104.1	648
119.1	649	[[image:image-20220825102844-3.png]]
106.1	650
119.1	651	4）Cable Wiring
106.1	652
119.1	653	* RS422
104.1	654
119.1	655	[[image:image-20220825103350-4.png]]
104.1	656
119.1	657	[[image:image-20220825100845-4.png]]
104.1	658
	659
119.1	660	== FX3U，3G，3GA Serial Protocol ==
56.1	661
106.1	662	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
56.1	663
119.1	664	1）V-BOX Settings
106.1	665
119.1	666	\|Item\|Settings\|Note
	667	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	668	\|Connection\|RS422/RS485/RS232\|
	669	\|Baud rate\|9600~~115200\|
	670	\|Data bit\|7/8\|
	671	\|Parity\|EVEN/Odd/None\|
	672	\|Stop bit\|1/2\|
	673	\|PLC station No.\|1~~255\|
106.1	674
119.1	675	2）Address List
106.1	676
119.1	677	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	678	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	679	\|Y\|Y\|Y o\|0~~303237\|
	680	\|M\|M\|M d\|0~~99999\|
	681	\|T\|T\|T d\|0~~99999\|
	682	\|C\|C\|C d\|0~~99999\|
	683	\|S\|S\|S d\|0~~99999\|
	684	\|SM\|SM\|SM d\|8000~~9999\|
	685	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	686	\|Y\|Y\|Y o\|0~~303237\|
	687	\|M\|M\|M d\|0~~99999\|
	688	\|T\|T\|T d\|0~~99999\|
	689	\|C\|C\|C d\|0~~199\|
	690	\|D\|D\|D d\|0~~7999\|
	691	\|S\|S\|S d\|0~~99999\|
	692	\|SD\|SD\|SD d\|8000~~9999\|
106.1	693
119.1	694	3）Configure the communication protocol
106.1	695
119.1	696	[[image:image-20220825102649-2.png]]
106.1	697
119.1	698	4）Cable Wiring
106.1	699
119.1	700	* RS422
106.1	701
119.1	702	[[image:image-20220825103421-5.png]]
106.1	703
119.1	704	[[image:image-20220825100845-4.png]]
106.1	705
	706
119.1	707	== FX5U Serial Protocol ==
103.1	708
107.1	709	Mitsubishi FX5U series PLC
103.1	710
119.1	711	1）V-BOX Settings
107.1	712
119.1	713	\|Item\|Settings\|Note
	714	\|Protocol\|Mitsubishi FX5U\|
	715	\|Connection\|RS422/RS485\|
	716	\|Baud rate\|9600\|
	717	\|Data bit\|7\|
	718	\|Parity\|Odd\|
	719	\|Stop bit\|1\|
	720	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
107.1	721
119.1	722	2）Address List
107.1	723
119.1	724	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	725	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	726	\|Y\|Y\|Y o\|0~~303237\|
	727	\|M\|M\|M d\|0~~99999\|
	728	\|B\|B\|B h\|0~~7FFF\|
	729	\|F\|F\|F d\|0~~32767\|
	730	\|SB\|SB\|SB h\|0~~7FFF\|
	731	\|TS\|TS\|TS d\|0~~1023\|
	732	\|TC\|TC\|TC d\|0~~1023\|
	733	\|STS\|STS\|STS d\|0~~1023\|
	734	\|STC\|STC\|STS d\|0~~1023\|
	735	\|CS\|CS\|CS d\|0~~1023\|
	736	\|CC\|CC\|CC d\|0~~1023\|
	737	\|SM\|SM\|SM d\|0~~9999\|
	738	\|L\|L\|L d\|0~~32767\|
	739	\|S\|S\|S d\|0~~4095\|
	740	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	741	\|TN\|TN\|TN d\|0~~1023\|
	742	\|STN\|STN\|STN d\|0~~1023\|
	743	\|CN\|CN\|CN d\|0~~1023\|
	744	\|R\|R\|R d\|0~~32767\|
	745	\|SW\|SW\|SW h\|0~~7FFF\|
	746	\|Z\|Z\|Z d\|0~~23\|
	747	\|D\|D\|D d\|0~~7999\|
	748	\|SD\|SD\|SD d\|0~~11999\|
107.1	749
119.1	750	3）PLC Settings (GX Works 3)
107.1	751
	752	Create a blank FX5U project
	753
	754	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	755
119.1	756	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
107.1	757
	758	Select protocol in the setting item, and set parameters.
	759
119.1	760	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
107.1	761
	762	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	763
119.1	764	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
107.1	765
	766	Click the [Apply] button to finish the setting.
	767
	768	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	769
119.1	770	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
107.1	771
	772	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	773
	774	Done.
	775
119.1	776	4）Configure the communication protocol
107.1	777
119.1	778	[[image:image-20220825104904-1.png]]
107.1	779
119.1	780	5）Cable Wiring
107.1	781
	782
119.1	783	* RS422
107.1	784
119.1	785	[[image:image-20220825105105-2.png]]
107.1	786
119.1	787	[[image:image-20220825105533-3.png]]
107.1	788
119.1	789	== FX5U Ethernet Protocol ==
100.1	790
	791	Mitsubishi FX5U series PLC
	792
119.1	793	1）V-BOX Settings
100.1	794
119.1	795	\|Items\|Settings\|Note
	796	\|Protocol\|Mitsubishi FX5U\|
	797	\|Connection\|Ethernet\|
	798	\|Port No.\|5002\|Must be the same as the PLC setting
	799	\|PLC station No.\|0\|
100.1	800
119.1	801	2）Address List
100.1	802
119.1	803	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	804	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	805	\|Y\|Y\|Y o\|0~~303237\|
	806	\|M\|M\|M d\|0~~99999\|
	807	\|B\|B\|B h\|0~~7FFF\|
	808	\|F\|F\|F d\|0~~32767\|
	809	\|SB\|SB\|SB h\|0~~7FFF\|
	810	\|TS\|TS\|TS d\|0~~1023\|
	811	\|TC\|TC\|TC d\|0~~1023\|
	812	\|STS\|STS\|STS d\|0~~1023\|
	813	\|STC\|STC\|STS d\|0~~1023\|
	814	\|CS\|CS\|CS d\|0~~1023\|
	815	\|CC\|CC\|CC d\|0~~1023\|
	816	\|SM\|SM\|SM d\|0~~9999\|
	817	\|L\|L\|L d\|0~~32767\|
	818	\|S\|S\|S d\|0~~4095\|
	819	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	820	\|TN\|TN\|TN d\|0~~1023\|
	821	\|STN\|STN\|STN d\|0~~1023\|
	822	\|CN\|CN\|CN d\|0~~1023\|
	823	\|R\|R\|R d\|0~~32767\|
	824	\|SW\|SW\|SW h\|0~~7FFF\|
	825	\|Z\|Z\|Z d\|0~~23\|
	826	\|D\|D\|D d\|0~~7999\|
	827	\|SD\|SD\|SD d\|0~~11999\|
100.1	828
119.1	829	3）PLC Settings (GX Works 3)
100.1	830
	831	Find the [Ethernet port] in the navigation area.
	832
119.1	833	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
100.1	834
	835	Select [Own Node Settings] in the [Setting Item List];
	836
	837	Set [IP Address], [Subnet Mask], [Default Gateway];
	838
	839	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	840
119.1	841	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
100.1	842
	843	Select [SLMP Connection Module] and add into host station as below picture shows;
	844
	845	Set Port number as 5002 (this is necessary settings);
	846
	847	Click [Close with Reflecting the Setting] to save and close window;
	848
119.1	849	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
100.1	850
	851	Click [Apply] to completed Etherenet settings;
	852
	853	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	854
119.1	855	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
100.1	856
119.1	857	4）Configure the communication protocol
110.1	858
119.1	859	[[image:image-20220825112403-1.png\|\|alt="图片-20220825112403-1.png"]]
110.1	860
119.1	861	5）电缆布线
110.1	862
119.1	863	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
113.1	864
122.1	865
	866	== L02 Serial Protocol ==
	867
134.1	868	Mitsubishi L02 series CPU built-in serial port.
122.1	869
135.1	870	1）V-BOX Settings
122.1	871
134.1	872	\|Item\|Settings\|Note
	873	\|Protocol\|Mitsubishi L02\|
	874	\|Connection\|RS422\|
	875	\|Baud rate\|115200\|
	876	\|Data bit\|8\|
	877	\|Parity\|Odd\|
	878	\|Stop bit\|1\|
	879	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
122.1	880
135.1	881	2）Address List
122.1	882
	883	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	884	\|Bit\|X\|X\|X h\|0~~FFFF\|
	885	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	886	\|Bit\|M\|M\|M d\|0~~9999\|
	887	\|Bit\|L\|L\|L d\|0~~9999\|
	888	\|Bit\|F\|F\|F d\|0~~9999\|
	889	\|Bit\|B\|B\|B h\|0~~FFFF\|
	890	\|Bit\|V\|V\|V d\|0~~2047\|
	891	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	892	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	893	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	894	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	895	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	896	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	897	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	898	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	899	\|Bit\|S\|S\|S d\|0~~9999\|
	900	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	901	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	902	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	903	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	904	\|Word\|W\|W\|W h\|0~~FFFF\|
	905	\|Word\|TN\|TN\|TN d\|0~~99999\|
	906	\|Word\|SN\|SN\|SN d\|0~~99999\|
	907	\|Word\|CN\|CN\|CN d\|0~~99999\|
	908	\|Word\|R\|R\|R d\|0~~99999\|
	909	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	910	\|Word\|Z\|Z\|Z d\|0~~99999\|
	911	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	912	\|Word\|D\|D\|D d\|0~~99999\|
	913
135.1	914	3）Communication Settings
122.1	915
134.1	916	[[image:image-20220825160648-3.png]]
122.1	917
135.1	918	4）Cable Wiring
122.1	919
134.1	920	* RS422
122.1	921
134.1	922	[[image:image-20220825161612-8.png]]
122.1	923
134.1	924	[[image:image-20220825160820-4.png]]
122.1	925
118.1	926	== L02 Ethernet Protocol ==
113.1	927
114.1	928	Mitsubishi L series CPU built-in Ethernet port.
113.1	929
115.1	930	1）V-BOX Settings
113.1	931
	932	\|Items\|Settings\|Note
	933	\|Protocol\|MIT L02 CPU MELSEC\|
	934	\|Connection\|Ethernet\|
	935	\|Port No.\|1025\|Must be the same as the PLC setting
	936	\|PLC station No.\|0\|Must be the same as the PLC setting
	937
115.1	938	2）Address List
113.1	939
	940	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	941	\|Bit\|X\|X\|X h\|0~~FFFF\|
	942	\|Bit\|Y\|Y\|Y h\|0~~FFFF\|
	943	\|Bit\|M\|M\|M d\|0~~9999\|
	944	\|Bit\|L\|L\|L d\|0~~9999\|
	945	\|Bit\|F\|F\|F d\|0~~9999\|
	946	\|Bit\|B\|B\|B h\|0~~FFFF\|
	947	\|Bit\|V\|V\|V d\|0~~2047\|
	948	\|Bit\|TC\|TC\|TC d\|0~~9999\|
	949	\|Bit\|SS\|SS\|SS d\|0~~9999\|
	950	\|Bit\|SC\|SC\|SC d\|0~~9999\|
	951	\|Bit\|CS\|CS\|CS d\|0~~9999\|
	952	\|Bit\|CC\|CC\|CC d\|0~~9999\|
	953	\|Bit\|SB\|SB\|SB h\|0~~FFFF\|
	954	\|Bit\|SM\|SM\|SM d\|0~~2047\|
	955	\|Bit\|STS\|STS\|STS d\|0~~1023\|
	956	\|Bit\|S\|S\|S d\|0~~9999\|
	957	\|Bit\|DX\|DX\|DX h\|0~~FFFF\|
	958	\|Bit\|DY\|DY\|DY h\|0~~FFFF\|
	959	\|Bit\|TS\|TS\|TS d\|0~~9999\|
	960	\|Bit\|Dbit\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
	961	\|Word\|W\|W\|W h\|0~~FFFF\|
	962	\|Word\|TN\|TN\|TN d\|0~~99999\|
	963	\|Word\|SN\|SN\|SN d\|0~~99999\|
	964	\|Word\|CN\|CN\|CN d\|0~~99999\|
	965	\|Word\|R\|R\|R d\|0~~99999\|
	966	\|Word\|SW\|SW\|SW h\|0~~FFFF\|
	967	\|Word\|Z\|Z\|Z d\|0~~99999\|
	968	\|Word\|ZR\|ZR\|ZR h\|0~~FFFF\|
	969	\|Word\|D\|D\|D d\|0~~99999\|
	970
121.1	971	3）PLC Settings (GX Works2 )
113.1	972
	973	Create a project
	974
	975	Set PLC IP, subnet mask and gateway;
	976
	977	Select [Binary Code] as communication data code;
	978
	979	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
	980
	981	Set PLC port number, for example 1025
	982
	983	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
	984
	985	Save settings;
	986
	987	Download project into PLC device;
	988
	989	Restart PLC device;
	990
121.1	991	4）Configure the communication protocol
	992
	993	[[image:image-20220825142659-1.png]]
	994
115.1	995	5）Cable Wiring
113.1	996
109.1	997	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
100.1	998
119.1	999	== QJ71E71 Ethernet Protocol ==
1.1	1000
119.1	1001	Mitsubishi QJ71E71 Ethernet communication module;
1.1	1002
120.1	1003	1）V-BOX Settings
1.1	1004
119.1	1005	\|Items\|Settings\|Note
	1006	\|Protocol\|MIT QJ71E71 MELSEC\|
	1007	\|Connection\|Ethernet\|
	1008	\|Port No.\|1025\|Must be the same as the PLC setting
	1009	\|PLC station No.\|0\|Must be the same as the PLC setting
1.1	1010
120.1	1011	2）Address List
48.1	1012
119.1	1013	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	1014	\|(% rowspan="18" %)Bit\|X\|X\|X h\|0~~1FFF\|
	1015	\|Y\|Y\|Y h\|0~~1FFF\|
	1016	\|M\|M\|M d\|0~~99999\|
	1017	\|L\|L\|L d\|0~~8191\|
	1018	\|F\|F\|F d\|0~~2047\|
	1019	\|B\|B\|B h\|0~~1FFF\|
	1020	\|V\|V\|V d\|0~~2047\|
	1021	\|TS\|TS\|TS d\|0~~2047\|
	1022	\|TC\|TC\|TC d\|0~~2047\|
	1023	\|SS\|SS\|SS d\|0~~2047\|
	1024	\|SC\|SC\|SC d\|0~~2047\|
	1025	\|CS\|CS\|CS d\|0~~1023\|
	1026	\|CC\|CC\|CC d\|0~~1023\|
	1027	\|SB\|SB\|SB h\|0~~7FF\|
	1028	\|S\|S\|S d\|0~~8191\|
	1029	\|DX\|DX\|DX h\|0~~1FFF\|
	1030	\|DY\|DY\|DY h\|0~~1FFF\|
	1031	\|SM\|SM\|SM d\|8000~~9999\|
	1032	\|(% rowspan="10" %)Word\|SD\|SD\|SD d\|0~~2047\|
	1033	\|D\|D\|D d\|0~~12287\|
	1034	\|W\|W\|W h\|0~~1FFF\|
	1035	\|TN\|TN\|TN d\|0~~2047\|
	1036	\|SN\|SN\|SN d\|0~~2047\|
	1037	\|CN\|CN\|CN d\|0~~1023\|
	1038	\|R\|R\|R d\|0~~32767\|
	1039	\|SW\|SW\|SW h\|0~~7FF\|
	1040	\|Z\|Z\|Z d\|0~~15\|
	1041	\|ZR\|ZR\|ZR h\|0~~FE7FF\|
7.1	1042
120.1	1043	3）PLC Settings(GX Works2)
7.1	1044
119.1	1045	* Click [Ethernet/CC IE/MELSECNET];
	1046	* Please select [Ethernet] as network type;
	1047	* Set station I/O number according to situation (For example, 0000 means that the module is connected to PLC CPU in first order);
	1048	* Select [Online] as Mode;
	1049	* Click [Operation setting] to set IP;
	1050	* Select [Binary Code] as [Communication Data Code];
	1051	* Set protocol: TCP;
	1052	* Set [unpassive] in [Open system];
	1053	* Set [receive] in [Fixed buffer];
	1054	* Set [procedure Exist] in [Fixed buffer communication];
	1055	* Disable [Pairing open];
	1056	* Set [No confirm] in [Existence confirmation];
	1057	* Host station port number: 1025;
	1058	* Save settings;
	1059	* Download project into PLC and restart it
	1060
120.1	1061	4）Configure the communication protocol
119.1	1062
120.1	1063	[[image:image-20220825143728-1.png]]
	1064
	1065	5）Cable Wiring
	1066
119.1	1067	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png"]]
	1068
138.1	1069	= Create communication with Delta PLC =
119.1	1070
132.1	1071	== DVP Ethernet Protocol ==
131.1	1072
119.1	1073	[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
	1074
127.1	1075	== DVP serial protocol ==
119.1	1076
	1077	[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
	1078
142.1	1079	== AS Ethernet Protocol ==
	1080
	1081	1）V-BOX Settings
	1082
	1083	\|=Items\|=Settings\|=Note
	1084	\|Protocol\|DELTA AS300 MODBUS TCP\|
	1085	\|Connection\|Ethernet\|
	1086	\|Port No.\|502\|
	1087	\|Device No.\|1\|
	1088	\|HMI No.\|0\|
	1089
	1090	2）Address List
	1091
	1092	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	1093	\|Bit\|X\|X\|X d\|0~~63\|
	1094	\|Bit\|Y\|Y\|Y d\|0~~63\|
	1095	\|Bit\|D\|D\|D d\|0~~29999\|
	1096	\|Bit\|M\|M\|M d\|0~~8191\|
	1097	\|Bit\|SM\|SM\|SM d\|0~~4095\|
	1098	\|Bit\|S\|S\|S h\|0~~2047\|
	1099	\|Bit\|T\|T\|T d\|0~~511\|
	1100	\|Bit\|C\|C\|C d\|0~~511\|
	1101	\|Bit\|HC\|HC\|HC d\|0~~255\|
	1102	\|Word\|X\|X\|X h\|0~~63\|
	1103	\|Word\|Y\|Y\|Y d\|0~~63\|
	1104	\|Word\|SR\|SR\|SR d\|0~~2047\|
	1105	\|Word\|D\|D\|D d\|0~~29999\|
	1106	\|Word\|T\|T\|T d\|0~~511\|
	1107	\|Word\|C\|C\|C h\|0~~511\|
	1108	\|Word\|E\|E\|E d\|0~~9\|
	1109
	1110	3）Configure the communication protocol
	1111
	1112
	1113	[[image:image-20220831160010-4.png]]
	1114
	1115	4）Cable Wiring
	1116
	1117	Figure
	1118
	1119	[[image:image-20220831155101-1.png]][[image:image-20220831160055-5.png]]
	1120
	1121	Pin Definition Diagram
	1122
	1123	[[image:image-20220831155157-3.png]]
	1124
138.1	1125	= Create communication with Omron PLC =
119.1	1126
140.1	1127	== CP1 Series Protocol ==
131.1	1128
119.1	1129	[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CP1%20Series.zip]]
	1130
140.1	1131	== CP2M Series Protocol ==
119.1	1132
	1133	[[下载链接>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CJ2M.zip]]
	1134
143.1	1135
	1136	== EC55 Protocol ==
	1137
	1138	Supported device: EC55 temperature instrument
	1139
	1140	1）V-BOX Settings
	1141
	1142	\|Items\|Settings\|Note
	1143	\|Protocol\|Omron EC55\|
	1144	\|Connection\|RS485 (9600, 2, 7, EVEN)\|
	1145	\|Port No.\|None\|
	1146	\|PLC station No.\|0\|
	1147
	1148	2）Address List
	1149
	1150	\|Type\|Register\|Device range\|HMI range\|Function
	1151	\|(% rowspan="3" %)Double word\|C0\|0-13 (Hex)\|0-19\|Set read only parameter for area 0
	1152	\|C1\|0-4D(Hex)\|0-77\|Set Read/Write parameter for area 0
	1153	\|C3\|0-CD(Hex)\|0-205\|Set Read/Write parameter for area 1
	1154	\|(% rowspan="6" %)Word\|80\|0-13(Hex)\|0-19\|Set read only parameter in area 0
	1155	\|81\|0-4D(Hex)\|0-77\|Set Read/Write parameter in area 0
	1156	\|83\|0-CD(Hex)\|0-205\|Set Read/Write parameter in area 1
	1157	\|CP\|-\|0-6\|Read controller intrinsic property
	1158	\|CS\|-\|0-2\|Read controller states
	1159	\|CA\|-\|0-17\|Action command
	1160
	1161	3）Device Settings
	1162
	1163	Omron E5CC PLC configuration
	1164
	1165	After entering the Communication Settings menu, please set the parameters to the default values for the following table. Press the cycle key of the instrument to enter the next setting.
	1166
	1167	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_3d95e093792ba98a.png?width=550&height=229&rev=1.1\|\|alt="12.PLC Protocol_html_3d95e093792ba98a.png" height="229" width="550"]]
	1168
	1169	According to PLC configuration and communication port configuration information of the HMI, provide the corresponding steps and configuration screenshots. This configuration needs to communicate properly with the above PLC configuration. The project settings are as follows
	1170
	1171	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_be583aa69dd6cf4c.png?width=550&height=242&rev=1.1\|\|alt="12.PLC Protocol_html_be583aa69dd6cf4c.png" height="242" width="550"]]
	1172
	1173	✎Note: The communication settings for HMI should be consistent with this setting.
	1174
	1175	4）Configure the communication protocol
	1176
	1177	[[image:image-20220831161041-1.png]]
	1178
	1179	5）Cable Wiring
	1180
	1181	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5e9a81a14106da9e.png?width=392&height=223&rev=1.1\|\|alt="12.PLC Protocol_html_5e9a81a14106da9e.png" height="223" width="392"]]
	1182
	1183	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_1897d92be6948d58.png?width=393&height=223&rev=1.1\|\|alt="12.PLC Protocol_html_1897d92be6948d58.png" height="223" width="393"]]
	1184
	1185	✎Note:
	1186
	1187	* COM3 only available in PI8000/PI9000 series.
	1188	* CA address could not support continuous writing function；
	1189	* Because of CP address intrinsic property: read control intrinsic property, so please place the character input part in use. Set address with CP0 and character length 10, used to display controller type. And place a number input part, set address with CP5 (cache size). Do not place other CP type address without CP0 in screen, otherwise CP type address is invalid
	1190	* When set value into read & write address, it is necessary to switch the temperature instrument meter to the corresponding interface according to the menu of the instrument where the address locates, so that the value could be written, otherwise, the value could not be written; When the communication write setting of the instrument is turned off, the writing function is invalid. Writing function could be opened by using the 00 address of the CA register, which write 01 value.
	1191	* When continuous writing of a value to a read-write address, please make sure all continuous writing address could be written. Otherwise, if one of these addresses could not be written, then all continuous writing commands will fail.
	1192	* Because of the mechanism problem, this protocol could not support CompoWay/F function that is read-write function of variables in protocol document.
	1193	* When using double-word address, set the data format to 32 bits, otherwise the read/write function is unable.
	1194	* Please set the communication delay time of 10ms in setting, to avoid that the instrument may not be able to communicate in a short time due to too fast data access and too much connection requests.
	1195	* [[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_d428cad280fdefb3.png?width=347&height=276&rev=1.1\|\|alt="12.PLC Protocol_html_d428cad280fdefb3.png" height="276" width="347"]]Because of the particularity of the instrument, it is necessary to write the value of the address in the menu interface corresponding to the address, and to enter the menu where the address locates, so that the value could be written.
	1196
138.1	1197	= Create communication with Modbus RTU =
119.1	1198
131.1	1199	== V-BOX as Slave ==
119.1	1200
131.1	1201	Select the protocol "Modbus RTU Slave (All Fuction)",
50.1	1202
131.1	1203	Then set baud rate, port, stop bits, data bits, parity.
113.1	1204
50.1	1205	(% style="text-align:center" %)
119.1	1206	[[image:1624342015914-382.png\|\|height="486" width="800" class="img-thumbnail"]]
50.1	1207
131.1	1208	== V-BOX as Master ==
50.1	1209
131.1	1210	Select the protocol "Modbus RTU Master",
50.1	1211
131.1	1212	Then set baud rate, port, stop bits, data bits, parity
50.1	1213
	1214	(% style="text-align:center" %)
119.1	1215	[[image:1624348709622-711.png\|\|queryString="width=809&height=493" height="488" width="800" class="img-thumbnail"]]
50.1	1216
131.1	1217	address list
50.1	1218
	1219	(% class="table-bordered" %)
131.1	1220	\|type\|register\|Function code and description
	1221	\|(% rowspan="11" %)词\|(% rowspan="3" %)3\|04 (Read Input Registers: Read the current binary value in one or more input registers)
119.1	1222	\|06 (write single register: write a binary value to a holding register)
	1223	\|10 (write values to multiple addresses )
	1224	\|(% rowspan="3" %)4\|03 (read holding register: read current binary value in one or more holding registers)
	1225	\|06 (write single register: write a binary value to a holding register)
	1226	\|10 (write values to multiple addresses )
	1227	\|(% rowspan="3" %)W6\|03 (read holding register: read current binary value in one or more holding registers)
	1228	\|06 (write single register: write a binary value to a holding register)
	1229	\|10 (write values to multiple addresses )
	1230	\|(% rowspan="2" %)W16\|03 (read holding register: read current binary value in one or more holding registers)
	1231	\|10 (write values to multiple addresses )
	1232	\|(% rowspan="11" %)Bit\|(% rowspan="3" %)0\|01 (Read coil state)
	1233	\|05 (Force a single coil to force the on/off state of a logic coil)
	1234	\|0F (Write multiple bits, ie write continuously)
	1235	\|(% rowspan="3" %)1\|02 (Read the input state)
	1236	\|05 (Force a single coil to force the on/off state of a logic coil)
	1237	\|0F (Write multiple bits)
	1238	\|(% rowspan="3" %)W5\|01 (Read coil state to obtain the current state of a set of logic coils)
	1239	\|05 (Force a single coil to force the on/off state of a logic coil)
	1240	\|0F (Write multiple bits)
	1241	\|(% rowspan="2" %)W15\|01 (Read coil state to obtain the current state of a set of logic coils)
	1242	\|0F (Write multiple bits)
50.1	1243
119.1	1244	== communicate with VB inverter ==
52.1	1245
119.1	1246	[[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
52.1	1247
119.1	1248	= User define protocol =
1.1	1249
19.1	1250	More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
1.1	1251
119.1	1252	== Read the temperature sensor. ==
1.1	1253
	1254	the commond format is as beliow:
	1255
	1256	Send commond:01 03 02 00 00 03 04 73
	1257
	1258	Feedback commond:01 03 06 07 F7 0E 7E B7 35
	1259
	1260	Temperature data:07 F7,desimal = 2039,it means temperature is 20.39℃.
	1261
	1262	Humidity data:0E 7E,desimal = 3710, it mean humidity is 37.10%RH.
	1263
	1264	Script Demo:
	1265
	1266	~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~--
	1267
	1268	function com.main()
	1269	~-~-dosomething
	1270	openPlc()
	1271	end
	1272	function openPlc()
	1273	if obj then
	1274	~-~- If the serial port opened,then read/write data by timing
	1275
	1276	local wri = string.pack(">HHHH",0X0103,0X0200,0X0003,0X0473)
	1277	local arr = reading(wri)
	1278	~-~- if arr ~~=nil then
	1279	~-~- if arr[1] ==33 and arr[2] ==v[2][2] and arr[3] ==v[2][3] then
	1280	~-~- local A = arr[4]*256
	1281	~-~- local B = A+arr[5]
	1282	~-~- addr_setword(v[1],B)
	1283	~-~- end
	1284	~-~- end
	1285
	1286	else
	1287	~-~-judge if there is a serial object, then initialize and open the serial port
	1288	local configs = {
	1289	name = 'COM1', ~-~-Select serial port COM1
	1290	mode = 485, ~-~-Communication mode RS485
	1291	baud_rate = 9600, ~-~-Baud rate 9600
	1292	stop_bit = 1, ~-~-stop bit 1
	1293	data_len = 8, ~-~-data length 8
	1294	check_bit = 'NONE', ~-~-no parity
	1295
	1296	}
	1297	obj,err = serial.open(configs) ~-~-Open serial port
	1298	if not obj then
	1299	print("serial open :failed", err) ~-~- Open serial port failed
	1300	end
	1301	end
	1302	end
	1303
	1304	function reading(wri)
	1305	obj:flush() ~-~- Clear serial port
	1306	obj:write(wri) ~-~- Write serial port
	1307	print(string.byte(wri,1,#wri))
	1308	obj:flush() ~-~- Clear serial port
	1309	local readed =obj:read(9,1000) ~-~- Read 9 bytes, timeout 1 second
	1310	if readed and readed ~~= "" then
	1311	~-~- judge that a non-empty string is read
	1312	print(string.byte(readed,1,#readed))
	1313	a={string.byte(readed, 1, #readed)}
	1314	if nil ~~= a[4] and nil ~~= a[5] and nil ~~= a[6] and nil ~~= a[7] then
	1315	a1=a[4]*256+a[5]
	1316	a2=a[6]*256+a[7]
	1317	addr_setword("@HDW0",a1)
	1318	addr_setword("@HDW1",a2)
	1319	end
	1320	return {string.byte(readed, 1, #readed)}
	1321	elseif readed == nil then
	1322	print("serial read err:", err or "")
	1323	return nil
	1324	end
	1325	return nil
	1326	end
	1327
	1328	~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-

Wiki source code of 1 Communication

Navigation

Table of Contents