Skip to Content

Changes for page 4 Common function of VB

Last modified by Theodore Xu on 2025/02/27 09:58
From version 37.1
edited by Theodore Xu
on 2024/07/31 11:26
Change comment: There is no comment for this version
To version 26.1
edited by Theodore Xu
on 2024/04/22 13:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,18 +16,3 @@
1 -= Parameters uploading and downloading =
2 -
3 -(% class="box infomessage" %)
4 -(((
5 -**✎Note:**
6 -1.Parameter uploading and downloading is only supported between the same models.
7 -2.F7.11 shows the software version of the inverter, the parameters may differ between different versions, especially between 2.072 and versions below 2.072.
8 -)))
9 -
10 -1.Press MF.K and ↑ and wait while the keyboard displays "u~-~-~-~-", the keyboard is uploading the parameters.
11 -
12 -2.Remove the keyboard and install to other VB.  Please be careful to align the pins when unplugging and plugging in the keyboard.
13 -
14 -3.Press MF.K and ↓ and wait while the keyboard display"d~-~-~-~-", the keyboard is downloading the parameters.
15 -
16 16  = **Start up** =
17 17  
18 18  ~1. Keyboard start and stop, panel potentiometer speed regulation. (F5.17 adjusts the change amplitude of the panel potentiometer)
... ... @@ -457,25 +457,12 @@
457 457  
458 458  Braking resistor
459 459  
460 -= **EMC** =
445 += **Installation guidance required by EMC** =
461 461  
462 - The input terminal of the inverter has EMC screw access option.
447 + The input terminal of the inverter has EMC screw access option.
463 463  
464 -* EMC Screws Installation Role: Filter out the common mode interference signals on the input side to the ground.
465 -* EMC Screw Removal Function: When the grounding of the whole equipment system is unstable, it is easy for the interference signal to enter the input terminal of the VFD, which leads to the inaccurate operation of the terminal motor, and then it is necessary to remove the EMC screws on the machine in order to solve the influence of external interference.
449 += Torque mode control winding project =
466 466  
467 -(% class="box infomessage" %)
468 -(((
469 -Do not remove the EMC unless there are special circumstances.
470 -)))
471 -
472 -(% style="text-align:center" %)
473 -[[image:企业微信截图_16890580824807.png||height="394" width="284"]]
474 -
475 -
476 -
477 -= Torque mode control on winding project =
478 -
479 479  Torque mode can only be vector control, torque control refers to the strength, that in the torque mode F0.03 is the default value, modify F0.03 for other values is invalid.
480 480  
481 481  Debugging ideas:
... ... @@ -496,11 +496,11 @@
496 496  
497 497  F0.00=0 Vector control
498 498  
499 -F0.18=2.0 Acceleration time
471 +F0.18=2.0 acceleration time
500 500  
501 -F0.19=2.0 Deceleration time
473 +F0.19=2.0 deceleration time
502 502  
503 -F2.01=Motor rated power
475 +F2.01=motor rated power
504 504  
505 505  F2.02=Motor rated voltage
506 506  
... ... @@ -510,38 +510,38 @@
510 510  
511 511  F2.05=Rated motor speed
512 512  
513 -F2.11=1 Static tuning
485 +F2.11=1 static tuning
514 514  
515 -F3.01=0.2 Speed loop integration time
487 +F3.01=0.2 speed loop integration time
516 516  
517 -F3.07=0.005 Speed loop filter coefficient
489 +F3.07=0.005 speed loop filter coefficient
518 518  
519 -F3.09=1 Torque control
491 +F3.09=1 torque control
520 520  
521 -F3.10=1 Torque control upper limit source
493 +F3.10=1 torque control upper limit source
522 522  
523 -F3.11=200 Torque upper limit setting
495 +F3.11=200 torque upper limit setting
524 524  
525 -F3.12=50 Torque control maximum frequency
497 +F3.12=50 torque control maximum frequency
526 526  
527 -F3.14=1.2 Torque control acceleration time
499 +F3.14=1.2 torque control acceleration time
528 528  
529 -F3.15=1.2 Torque control deceleration time
501 +F3.15=1.2 torque control deceleration time
530 530  
531 -F3.16=120 Torque stiffness factor
503 +F3.16 = 120 torque stiffness factor
532 532  
533 533  Torque control commissioning instructions:
534 534  
535 -F0.18: Frequency acceleration time
507 +F0.18: frequency acceleration time
536 536  
537 -F0.19: Frequency deceleration time
509 +F0.19: frequency deceleration time
538 538  
539 -F3.14: Torque acceleration time
511 +F3.14: torque acceleration time
540 540  
541 -F3.15: Torque deceleration time
513 +F3.15: torque deceleration time
542 542  
543 -F3.07: Frequency low-pass filtering factor
515 +F3.07: frequency low-pass filtering factor
544 544  
545 -F3.24: Static friction compensation
517 +F3.24: static friction compensation
546 546  
547 -F3.25: Static friction compensation time
519 +F3.25: static friction compensation time
企业微信截图_16890580824807.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -423.4 KB
Content