Skip to Content

Changes for page 4 Common function of VB

Last modified by Theodore Xu on 2025/02/27 09:58
From version 38.1
edited by Theodore Xu
on 2025/02/27 09:58
Change comment: There is no comment for this version
To version 28.1
edited by Theodore Xu
on 2024/04/22 14:31
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,18 +16,3 @@
1 -= Parameters uploading and downloading =
2 -
3 -(% class="box infomessage" %)
4 -(((
5 -**✎Note:**
6 -1.Parameter uploading and downloading is only supported between the same models.
7 -2.F7.11 shows the software version of the inverter, the parameters may differ between different versions, especially between 2.072 and versions below 2.072.
8 -)))
9 -
10 -1.Press MF.K and ↑ and wait while the keyboard displays "u~-~-~-~-", the keyboard is uploading the parameters.
11 -
12 -2.Remove the keyboard and install to other VB.  Please be careful to align the pins when unplugging and plugging in the keyboard.
13 -
14 -3.Press MF.K and ↓ and wait while the keyboard display"d~-~-~-~-", the keyboard is downloading the parameters.
15 -
16 16  = **Start up** =
17 17  
18 18  ~1. Keyboard start and stop, panel potentiometer speed regulation. (F5.17 adjusts the change amplitude of the panel potentiometer)
... ... @@ -381,7 +381,7 @@
381 381  If the value of F7.11 is less than or equal to 2.064, use PID parameter group F9.
382 382  F0.20=1 Factory data reset
383 383  F0.03=8
384 -F5.23=2 Change AI2 range from 0-20mA to 4-20 mA.
369 +F5.23=2
385 385  F9.01=Upper limit water pressure
386 386  F9.02=1 (AI2)
387 387  F9.28=1
... ... @@ -457,25 +457,12 @@
457 457  
458 458  Braking resistor
459 459  
460 -= **EMC** =
445 += **Installation guidance required by EMC** =
461 461  
462 - The input terminal of the inverter has EMC screw access option.
447 + The input terminal of the inverter has EMC screw access option.
463 463  
464 -* EMC Screws Installation Role: Filter out the common mode interference signals on the input side to the ground.
465 -* EMC Screw Removal Function: When the grounding of the whole equipment system is unstable, it is easy for the interference signal to enter the input terminal of the VFD, which leads to the inaccurate operation of the terminal motor, and then it is necessary to remove the EMC screws on the machine in order to solve the influence of external interference.
449 += Torque mode control winding project =
466 466  
467 -(% class="box infomessage" %)
468 -(((
469 -Do not remove the EMC unless there are special circumstances.
470 -)))
471 -
472 -(% style="text-align:center" %)
473 -[[image:企业微信截图_16890580824807.png||height="394" width="284"]]
474 -
475 -
476 -
477 -= Torque mode control on winding project =
478 -
479 479  Torque mode can only be vector control, torque control refers to the strength, that in the torque mode F0.03 is the default value, modify F0.03 for other values is invalid.
480 480  
481 481  Debugging ideas:
企业微信截图_16890580824807.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -423.4 KB
Content