Changes for page 4 Common function of VB
Last modified by Theodore Xu on 2025/07/09 14:51
From version 39.1
edited by Theodore Xu
on 2025/07/09 14:51
on 2025/07/09 14:51
Change comment:
There is no comment for this version
To version 26.1
edited by Theodore Xu
on 2024/04/22 13:56
on 2024/04/22 13:56
Change comment:
There is no comment for this version
Summary
-
Page properties (1 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 1 removed)
Details
- Page properties
-
- Content
-
... ... @@ -1,18 +16,3 @@ 1 -= Parameters uploading and downloading = 2 - 3 -(% class="box infomessage" %) 4 -((( 5 -**✎Note:** 6 -1.Parameter uploading and downloading is only supported between the same models. 7 -2.F7.11 shows the software version of the inverter, the parameters may differ between different versions, especially between 2.072 and versions below 2.072. 8 -))) 9 - 10 -1.Press MF.K and ↑ and wait while the keyboard displays "u~-~-~-~-", the keyboard is uploading the parameters. 11 - 12 -2.Remove the keyboard and install to other VB. Please be careful to align the pins when unplugging and plugging in the keyboard. 13 - 14 -3.Press MF.K and ↓ and wait while the keyboard display"d~-~-~-~-", the keyboard is downloading the parameters. 15 - 16 16 = **Start up** = 17 17 18 18 ~1. Keyboard start and stop, panel potentiometer speed regulation. (F5.17 adjusts the change amplitude of the panel potentiometer) ... ... @@ -381,6 +381,7 @@ 381 381 If the value of F7.11 is less than or equal to 2.064, use PID parameter group F9. 382 382 F0.20=1 Factory data reset 383 383 F0.03=8 369 +F5.23=2 384 384 F9.01=Upper limit water pressure 385 385 F9.02=1 (AI2) 386 386 F9.28=1 ... ... @@ -456,24 +456,12 @@ 456 456 457 457 Braking resistor 458 458 459 -= **EMC** = 445 += **Installation guidance required by EMC** = 460 460 461 - The input terminal of the inverter has EMC screw access option. 447 + The input terminal of the inverter has EMC screw access option. 462 462 463 -* EMC Screws Installation Role: Filter out the common mode interference signals on the input side to the ground. 464 -* EMC Screw Removal Function: When the grounding of the whole equipment system is unstable, it is easy for the interference signal to enter the input terminal of the VFD, which leads to the inaccurate operation of the terminal motor, and then it is necessary to remove the EMC screws on the machine in order to solve the influence of external interference. 449 += Torque mode control winding project = 465 465 466 -(% class="box infomessage" %) 467 -((( 468 -Do not remove the EMC unless there are special circumstances. 469 -))) 470 - 471 -(% style="text-align:center" %) 472 -[[image:企业微信截图_16890580824807.png||height="394" width="284"]] 473 - 474 - 475 -= Torque mode control on winding project = 476 - 477 477 Torque mode can only be vector control, torque control refers to the strength, that in the torque mode F0.03 is the default value, modify F0.03 for other values is invalid. 478 478 479 479 Debugging ideas: ... ... @@ -494,11 +494,11 @@ 494 494 495 495 F0.00=0 Vector control 496 496 497 -F0.18=2.0 Acceleration time471 +F0.18=2.0 acceleration time 498 498 499 -F0.19=2.0 Deceleration time473 +F0.19=2.0 deceleration time 500 500 501 -F2.01= Motor rated power475 +F2.01=motor rated power 502 502 503 503 F2.02=Motor rated voltage 504 504 ... ... @@ -508,38 +508,38 @@ 508 508 509 509 F2.05=Rated motor speed 510 510 511 -F2.11=1 Static tuning485 +F2.11=1 static tuning 512 512 513 -F3.01=0.2 Speed loop integration time487 +F3.01=0.2 speed loop integration time 514 514 515 -F3.07=0.005 Speed loop filter coefficient489 +F3.07=0.005 speed loop filter coefficient 516 516 517 -F3.09=1 Torque control491 +F3.09=1 torque control 518 518 519 -F3.10=1 Torque control upper limit source493 +F3.10=1 torque control upper limit source 520 520 521 -F3.11=200 Torque upper limit setting495 +F3.11=200 torque upper limit setting 522 522 523 -F3.12=50 Torque control maximum frequency497 +F3.12=50 torque control maximum frequency 524 524 525 -F3.14=1.2 Torque control acceleration time499 +F3.14=1.2 torque control acceleration time 526 526 527 -F3.15=1.2 Torque control deceleration time501 +F3.15=1.2 torque control deceleration time 528 528 529 -F3.16=120 Torque stiffness factor503 +F3.16 = 120 torque stiffness factor 530 530 531 531 Torque control commissioning instructions: 532 532 533 -F0.18: Frequency acceleration time507 +F0.18: frequency acceleration time 534 534 535 -F0.19: Frequency deceleration time509 +F0.19: frequency deceleration time 536 536 537 -F3.14: Torque acceleration time511 +F3.14: torque acceleration time 538 538 539 -F3.15: Torque deceleration time513 +F3.15: torque deceleration time 540 540 541 -F3.07: Frequency low-pass filtering factor515 +F3.07: frequency low-pass filtering factor 542 542 543 -F3.24: Static friction compensation517 +F3.24: static friction compensation 544 544 545 -F3.25: Static friction compensation time519 +F3.25: static friction compensation time
- 企业微信截图_16890580824807.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.AiXia - Size
-
... ... @@ -1,1 +1,0 @@ 1 -423.4 KB - Content