Skip to Content

Changes for page 09 Function code

Last modified by Iris on 2025/11/17 14:59
From version 6.1
edited by Iris
on 2025/11/13 17:40
Change comment: There is no comment for this version
To version 1.1
edited by Iris
on 2025/11/13 15:45
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,7 +1,7 @@
1 -== **F0 group basic function group** ==
1 +**F0 group basic function group**
2 2  
3 -|(% rowspan="2" style="text-align:center" %)F0.00|(% style="text-align:center" %)Motor control mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)1
4 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
3 +|(% rowspan="2" %)F0.00|Motor control mode|Factory default|1
4 +|Setting range|(% colspan="2" %)(((
5 5  0: Speed sensorless vector control (SVC)
6 6  
7 7  1: V/F control
... ... @@ -17,8 +17,8 @@
17 17  
18 18  Tip: When selecting the vector control mode, the motor parameter identification process must be carried out. Only accurate motor parameters can give full play to the advantages of vector control.
19 19  
20 -|(% rowspan="2" style="text-align:center" %)F0.01|(% style="text-align:center" %)Command source selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
21 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
20 +|(% rowspan="2" %)F0.01|Command source selection|Factory default|0
21 +|Setting range|(% colspan="2" %)(((
22 22  0: Operation panel command channel
23 23  
24 24  1: Terminal command channel
... ... @@ -44,8 +44,8 @@
44 44  
45 45  The host computer gives the running command control through the communication mode.
46 46  
47 -|(% rowspan="2" style="text-align:center" %)F0.02|(% style="text-align:center" %)Run time UP/DOWN benchmark|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)1
48 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
47 +|(% rowspan="2" %)F0.02|Run time UP/DOWN benchmark|Factory default|1
48 +|Setting range|(% colspan="2" %)(((
49 49  0: Operating frequency
50 50  
51 51  1: Setting frequency
... ... @@ -53,8 +53,13 @@
53 53  
54 54  This function only effective for frequency source digital setting, in order to determine the setting frequency of UP/DOWN is current running frequency or current setting frequency.
55 55  
56 -|(% rowspan="2" style="text-align:center" %)F0.03|(% style="text-align:center; width:240px" %)Main frequency source X choice|(% style="text-align:center; width:252px" %)Factory default|(% style="text-align:center" %)4
57 -|(% style="text-align:center; width:240px" %)Setting range|(% colspan="2" style="width:332px" %)(((
56 +
57 +
58 +
59 +
60 +
61 +|(% rowspan="2" %)F0.03|Main frequency source X choice|Factory default|4
62 +|Setting range|(% colspan="2" %)(((
58 58  0: Digital setting F0.08 (Adjustable terminal UP/DOWN, be not retained at power failure)
59 59  
60 60  1: Digital setting F0.08 (Adjustable terminal UP/DOWN, be retained at power failure)
... ... @@ -78,6 +78,8 @@
78 78  10: AI3(Expansion module)
79 79  )))
80 80  
86 +
87 +
81 81  Select the input channel for the main given frequency of the inverter. There are 10 main given frequency channels:
82 82  
83 83  0: Digital setting (no memory) (Potentiometer and terminal UP/DOWN adjustable, power failure no memory) The initial value is F0.08 value of Digital Setting Preset Frequency. The set frequency value of the inverter can be changed by ▲/▼ key of the keyboard (or the UP and DOWN of the multi-function input terminal). No memory means that after the inverter power off, the set frequency value is restored to the initial value;
... ... @@ -98,8 +98,8 @@
98 98  
99 99  9: Communication set means that the main frequency source is given by the host computer through communication.
100 100  
101 -|(% rowspan="2" style="text-align:center" %)F0.04|(% style="text-align:center" %)Auxiliary frequency source Y selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)4
102 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
108 +|(% rowspan="2" %)F0.04|Auxiliary frequency source Y selection|Factory default|4
109 +|Setting range|(% colspan="2" %)(((
103 103  0: Numeric setting F0.08
104 104  
105 105  (Terminal UP/DOWN can be change, Power failure does not remember. It is cleared after switching as a frequency source.)
... ... @@ -125,21 +125,25 @@
125 125  9: Communication setting
126 126  )))
127 127  
135 +
136 +
128 128  The secondary frequency source Y is used in the same way as the primary frequency source X when it is used as an independent frequency given channel (that is, the frequency source selected to switch from X to Y).
129 129  
130 -|(% rowspan="2" style="text-align:center" %)F0.05|(% style="width:344px" %)The auxiliary frequency source Y range is selected during superposition|(% style="text-align:center; width:142px" %)Factory default|(% style="text-align:center" %)0
131 -|(% style="text-align:center; width:344px" %)Setting range|(% colspan="2" style="width:228px" %)(((
139 +|(% rowspan="2" %)F0.05|The auxiliary frequency source Y range is selected during superposition|Factory default|0
140 +|Setting range|(% colspan="2" %)(((
132 132  0: Relative to the maximum frequency  F0.10
133 133  
134 134  1: Relative to the frequency source X
135 135  )))
136 -|(% rowspan="2" style="text-align:center" %)F0.06|(% style="width:344px" %)Auxiliary frequency source Y range in superposition|(% style="text-align:center; width:142px" %)Factory default|(% style="text-align:center" %)100%
137 -|(% style="text-align:center; width:344px" %)Setting range|(% colspan="2" style="text-align:center; width:228px" %)0% to 150%
145 +|(% rowspan="2" %)F0.06|Auxiliary frequency source Y range in superposition|Factory default|100%
146 +|Setting range|(% colspan="2" %)0%-150%
138 138  
148 +
149 +
139 139  When the frequency source is selected as a frequency stack (F0.07 is set to 1, 3, or 4), it is used to determine the adjustment range of the auxiliary frequency source. F0.05 is used to determine the object relative to the range, if it is relative to the maximum frequency (F0.10), the range is a fixed value; If it is relative to the primary frequency source X, its range will change as the primary frequency source X changes.
140 140  
141 -|(% rowspan="2" style="text-align:center" %)F0.07|(% style="text-align:center; width:264px" %)Frequency source stack selection|(% style="text-align:center; width:234px" %)Factory default|(% style="text-align:center" %)0
142 -|(% style="text-align:center; width:264px" %)Setting range|(% colspan="2" style="width:308px" %)(((
152 +|(% rowspan="2" %)F0.07|Frequency source stack selection|Factory default|0
153 +|Setting range|(% colspan="2" %)(((
143 143  LED bits: Frequency source selection
144 144  
145 145  0: Primary frequency source
... ... @@ -165,23 +165,25 @@
165 165  4: Main x auxiliary
166 166  )))
167 167  
179 +
180 +
168 168  The secondary frequency source is used in the same way as the primary frequency source X when it is used as an independent frequency given channel (that is, the frequency source selected is switched from X to Y). When the secondary frequency source is used as a superposition given (i.e., the frequency source selected is X+Y, X to X+Y switching, or Y to X+Y switching), there are the following special features:
169 169  
170 170  When the auxiliary frequency source for digital or pulse potentiometer timing, preset frequency (F0.08) does not work, through the keyboard ▲/▼ key (or multi-function input terminal UP, DOWN) can be adjusted on the basis of the main given frequency.
171 171  
172 -When the auxiliary frequency source is given as an analog input (AI1, AI2) or a pulse input, 100% of the input setting corresponds to the auxiliary frequency source range (see F0.05 and F0.06 instructions). If you need to adjust up or down from the main given frequency, set the analog input to a range of n% to +n%.
185 +When the auxiliary frequency source is given as an analog input (AI1, AI2) or a pulse input, 100% of the input setting corresponds to the auxiliary frequency source range (see F0.05 and F0.06 instructions). If you need to adjust up or down from the main given frequency, set the analog input to a range of.n% to +n%.
173 173  
174 174  The frequency source is timed for pulse input, similar to analog quantity setting.
175 175  
176 176  Tip: The secondary frequency source Y and the primary frequency source X Settings cannot be the same, that is, the primary and secondary frequency sources cannot use the same frequency given channel.
177 177  
178 -|(% rowspan="2" style="text-align:center" %)F0.08|(% style="text-align:center" %)Keyboard setting frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)50.00Hz
179 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to Maximum frequency F0.10
191 +|(% rowspan="2" %)F0.08|Keyboard setting frequency|Factory default|50.00Hz
192 +|Setting range|(% colspan="2" %)0.00 to Maximum frequency F0.10
180 180  
181 181  When the frequency source is selected “Numeric setting F0.08 (Terminal UP/DOWN Adjustable, power down memory) ", the function code value sets the initial value for the frequency number of the inverter.
182 182  
183 -|(% rowspan="2" style="text-align:center" %)F0.09|(% style="text-align:center" %)Running direction selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
184 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
196 +|(% rowspan="2" %)F0.09|Running direction selection|Factory default|0
197 +|Setting range|(% colspan="2" %)(((
185 185  0: The same direction
186 186  
187 187  1: The direction is reversed
... ... @@ -193,13 +193,13 @@
193 193  
194 194  Tip: The motor running direction will be restored to the original state after parameter initialization. For the system debugging is strictly prohibited to change the motor steering occasions with caution.
195 195  
196 -|(% rowspan="2" style="text-align:center" %)F0.10|(% style="text-align:center" %)Maximum output frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)50.00 Hz
197 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 320.00Hz
209 +|(% rowspan="2" %)F0.10|Maximum output frequency|Factory default|50.00 Hz
210 +|Setting range|(% colspan="2" %)0.00 to 320.00Hz
198 198  
199 199  When F0.26=1, the upper limit of the maximum frequency is 1000Hz. When F0.26=2, the upper limit of the maximum frequency is 320Hz.
200 200  
201 -|(% rowspan="2" style="text-align:center" %)F0.11|(% style="text-align:center" %)Upper limit frequency source selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
202 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
214 +|(% rowspan="2" %)F0.11|Upper limit frequency source selection|Factory default|0
215 +|Setting range|(% colspan="2" %)(((
203 203  0: The number is F0.12
204 204  
205 205  1: AI1
... ... @@ -231,20 +231,20 @@
231 231  
232 232  For example, in torque control, speed control is not effective. In order to avoid the "speed" of material breakage, the upper limit frequency can be set with the analog quantity. When the inverter runs to the upper limit frequency value, the torque control is invalid and the inverter continues to run at the upper limit frequency.
233 233  
234 -|(% rowspan="2" style="text-align:center" %)F0.12|(% style="text-align:center" %)Upper limit frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)50.00Hz
235 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)Lower frequency F0.14 to Maximum frequency F0.10
236 -|(% rowspan="2" style="text-align:center" %)F0.13|(% style="text-align:center" %)Upper frequency bias|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
237 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00Hz to Maximum frequency F0.10
247 +|(% rowspan="2" %)F0.12|Upper limit frequency|Factory default|50.00Hz
248 +|Setting range|(% colspan="2" %)Lower frequency F0.14-Maximum frequency F0.10
249 +|(% rowspan="2" %)F0.13|Upper frequency bias|Factory default|0.00Hz
250 +|Setting range|(% colspan="2" %)0.00Hz to Maximum frequency F0.10
238 238  
239 239  When the upper limit frequency is given by the analog quantity, this parameter is used as the bias quantity calculated by the upper limit frequency, and this upper limit frequency offset is added to the set value of the upper limit frequency of the simulation as the set value of the final upper limit frequency.
240 240  
241 -|(% rowspan="2" style="text-align:center" %)F0.14|(% style="text-align:center" %)Lower frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
242 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00Hz to Upper limit frequency F0.12
254 +|(% rowspan="2" %)F0.14|Lower frequency|Factory default|0.00Hz
255 +|Setting range|(% colspan="2" %)0.00Hz to Upper limit frequency F0.12
243 243  
244 244  When the VFD starts to run, it starts from the start frequency. If the given frequency is less than the lower limit frequency during operation, the VFD runs at the lower limit frequency, stops or runs at zero speed. You can set which mode of operation to use with F0.15.
245 245  
246 -|(% rowspan="2" style="text-align:center" %)F0.15|(% style="text-align:center" %)Lower frequency Operating mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
247 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
259 +|(% rowspan="2" %)F0.15|Lower frequency Operating mode|Factory default|0
260 +|Setting range|(% colspan="2" %)(((
248 248  0: Run at the lower limit frequency
249 249  
250 250  1: Stop
... ... @@ -252,11 +252,15 @@
252 252  2: Zero speed operation
253 253  )))
254 254  
268 +
269 +
255 255  Select the operating state of the inverter when the set frequency is lower than the lower limit frequency. In order to avoid the motor running at low speed for a long time, you can use this function to choose to stop.
256 256  
257 -|(% rowspan="2" style="text-align:center" %)F0.16|(% style="text-align:center" %)Carrier frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
258 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.5kHz to 16.0kHz
272 +|(% rowspan="2" %)[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps1.png]]F0.16|Carrier frequency|Factory default|Model determination
273 +|Setting range|(% colspan="2" %)0.5kHz to 16.0kHz
259 259  
275 +
276 +
260 260  This function regulates the carrier frequency of the inverter. By adjusting the carrier frequency, the motor noise can be reduced, the resonance point of the mechanical system can be avoided, and the interference of the line to the floor drain current and the VFD can be reduced.
261 261  
262 262  When the carrier frequency is low, the higher harmonic component of the output current increases, the motor loss increases, and the motor temperature rise increases.
... ... @@ -265,18 +265,19 @@
265 265  
266 266  The effect of adjusting the carrier frequency on the following performance:
267 267  
268 -|(% style="text-align:center" %)Carrier frequency|(% style="text-align:center" %)Low [[image:1763022484807-191.png]] High
269 -|(% style="text-align:center" %)Motor noise|(% style="text-align:center" %)High [[image:1763022495845-910.png]] Low
270 -|(% style="text-align:center" %)The output current waveform|(% style="text-align:center" %)Worse [[image:1763022525597-175.png]] Better
271 -|(% style="text-align:center" %)Temperature rise in electric motors|(% style="text-align:center" %)High [[image:1763022595008-156.png]] Low
272 -|(% style="text-align:center" %)VFD temperature rise|(% style="text-align:center" %)Low [[image:1763022599082-487.png]] High
273 -|(% style="text-align:center" %)Leak current|(% style="text-align:center" %)Low[[image:1763022602360-885.png]]High
274 -|(% style="text-align:center" %)External radiation interference|(% style="text-align:center" %)Low[[image:1763022605234-199.png]]High
275 275  
286 +|Carrier frequency|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps2.png]]Low High
287 +|Motor noise|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps3.png]]High Low
288 +|The output current waveform|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps4.png]]Worse Better
289 +|Temperature rise in electric motors|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps5.png]]High Low
290 +|VFD temperature rise|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps6.png]]Low High
291 +|Leak current|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps7.png]]Low High
292 +|External radiation interference|[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps8.png]]Low High
276 276  
277 277  
278 -|(% rowspan="2" style="text-align:center" %)F0.17|(% style="text-align:center" %)Carrier PWM baud selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)1010
279 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
295 +
296 +|(% rowspan="2" %)[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps9.png]]F0.17|Carrier PWM baud selection|Factory default|1010
297 +|Setting range|(% colspan="2" %)(((
280 280  Bits: Select PWM mode
281 281  
282 282  0: Automatic switching;
... ... @@ -305,11 +305,13 @@
305 305  
306 306  1: On
307 307  )))
308 -|(% rowspan="2" style="text-align:center" %)F0.18|(% style="text-align:center" %)Acceleration time 1|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
309 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 6500.0s
310 -|(% rowspan="2" style="text-align:center" %)F0.19|(% style="text-align:center" %)Deceleration time1|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
311 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 6500.0s
326 +|(% rowspan="2" %)F0.18|Acceleration time 1|Factory default|Model determination
327 +|Setting range|(% colspan="2" %)0.0s to 6500.0s
328 +|(% rowspan="2" %)F0.19|Deceleration time1|Factory default|Model determination
329 +|Setting range|(% colspan="2" %)0.0s to 6500.0s
312 312  
331 +
332 +
313 313  One place: Select PWM mode
314 314  
315 315  VFD can choose 5-section wave or 7-section wave, the 5-section wave converter has little heat, and the 7-section wave motor has little noise. When the bit is 0, 7 waves are generated at low frequency and 5 waves are generated at high frequency. At 1 o 'clock, the whole wave is 7 stages, and at 2 o'clock, the whole wave is 5 stages.
... ... @@ -318,7 +318,7 @@
318 318  
319 319  When the output frequency is low, reducing the PWM carrier can increase the low frequency starting torque and reduce the electromagnetic interference during starting. When the bit is 1, the program automatically reduces the PWM carrier when the output frequency is low.
320 320  
321 -Hundreds place: Random PWM depth
341 +Hundreds palce: Random PWM depth
322 322  
323 323  In order to make the motor noise spectrum flatter, you can turn on the random PWM function, after the function is turned on, the PWM carrier is no longer a fixed value, but fluctuates around the F0.16 set carrier. When the bit is not 0, the random PWM function works. The larger the value, the wider the fluctuation range and the flatter the noise spectrum. It should be noted that after opening the random carrier, the electromagnetic noise of the motor will not necessarily be reduced, and the actual noise perception varies from person to person.
324 324  
... ... @@ -330,12 +330,11 @@
330 330  
331 331  Deceleration time refers to the time required for the VFD to decelerate from the reference frequency of acceleration and deceleration (determined by F0.24) to the zero frequency, see t2 in Figure 9-0-1.
332 332  
333 -(% style="text-align:center" %)
334 -(((
335 -(% style="display:inline-block; width:616px;" %)
336 -[[Figure 9-0-1 Acceleration and deceleration time>>image:1763022803632-610.png||height="370" width="616"]]
337 -)))
338 338  
354 +[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps10.jpg]]
355 +
356 +Figure 9-0-1 Acceleration and deceleration time
357 +
339 339  Note the difference between the actual acceleration and deceleration time and the set acceleration and deceleration time.
340 340  
341 341  There are four groups of acceleration and deceleration time selection
... ... @@ -350,12 +350,13 @@
350 350  
351 351  The acceleration and deceleration time can be selected through the multifunctional digital input terminals (F5.00 to F5.03).
352 352  
353 -|(% rowspan="2" style="text-align:center" %)F0.20|(% style="text-align:center" %)Parameter initialization|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
354 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
355 -0: No operation
356 356  
357 -1: Restore factory default (Do not restore motor parameters)
373 +|(% rowspan="2" %)F0.20|Parameter initialization|Factory default|0
374 +|Setting range|(% colspan="2" %)(((
375 +0: No opreration
358 358  
377 +1: Restore factorydefault (Do not restore motor parameters)
378 +
359 359  2: Clear the record information
360 360  
361 361  3: Restore factory default (Restore motor parameters)
... ... @@ -369,8 +369,8 @@
369 369  
370 370  3: Restore all factory settings, including motor parameters, and clear the recorded information at the same time.
371 371  
372 -|(% rowspan="2" style="text-align:center" %)F0.23|(% style="text-align:center" %)Unit of acceleration and deceleration time|(% style="text-align:center" %)Factory default|1
373 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:left" %)(((
392 +|(% rowspan="2" %)F0.23|Unit of acceleration and deceleration time|Factory default|1
393 +|Setting range|(% colspan="2" %)(((
374 374  0: 1s
375 375  
376 376  1: 0.1s
... ... @@ -384,8 +384,8 @@
384 384  
385 385  Note the following function codes: F0.18, F0.19, F8.01, F8.02, F8.03, F8.04, F8.05, F8.06, F8.07, F8.08.
386 386  
387 -|(% rowspan="2" style="text-align:center" %)F0.24|(% style="text-align:center; width:382px" %)Acceleration and deceleration time reference frequency|(% style="text-align:center; width:147px" %)Factory default|(% style="text-align:center; width:33px" %)0
388 -|(% style="text-align:center; width:382px" %)Setting range|(% colspan="2" style="width:180px" %)(((
407 +|(% rowspan="2" %)F0.24|Acceleration and deceleration time reference frequency|Factory default|0
408 +|Setting range|(% colspan="2" %)(((
389 389  0: Maximum frequency (F0.10)
390 390  
391 391  1: Set the frequency
... ... @@ -395,9 +395,9 @@
395 395  
396 396  Define the frequency range corresponding to the acceleration and deceleration time. See Figure 9-0-1 Acceleration and deceleration time.
397 397  
398 -|(% rowspan="2" style="text-align:center" %)F0.25|(% style="text-align:center" %)Fan control|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)01
399 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
400 -One place: Start/stop control
418 +|(% rowspan="2" %)F0.25|Fan control|Factory default|01
419 +|Setting range|(% colspan="2" %)(((
420 +One place: start/stop control
401 401  
402 402  0: The fan runs after the inverter is powered on
403 403  
... ... @@ -420,24 +420,29 @@
420 420  
421 421  Speed control: Below 45°C: Operate at 50% speed; From 45°C to 50°C: Operate at 75% speed; At 50°C and above: Operate at 100% speed.
422 422  
423 -|(% rowspan="2" style="text-align:center" %)F0.26|(% style="text-align:center" %)Frequency command decimal point|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)2
424 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)(((
443 +
444 +|(% rowspan="2" %)F0.26|Frequency command decimal point|Factory default|2
445 +|Setting range|(% colspan="2" %)(((
425 425  1: 1 decimal places
426 426  
427 427  2: 2 decimal places
428 428  )))
429 429  
451 +
452 +
430 430  This parameter is not restored when restoring factory defaults.
431 431  
432 -|(% rowspan="2" style="text-align:center" %)F0.27|(% style="text-align:center" %)Modulation ratio coefficient|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)100.0%
433 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)10.0 to 150.0%
455 +|(% rowspan="2" %)F0.27|Modulation ratio coefficient|Factory default|100.0%
456 +|Setting range|(% colspan="2" %)10.0 to 150.0%
434 434  
458 +
459 +
435 435  This parameter is the upper limit of the modulation ratio. The lower the modulation ratio, the lower the maximum output voltage; The higher the modulation ratio, the more obvious the current distortion during over modulation.
436 436  
437 -== **F1 group start stop control** ==
462 +**F1 group start stop control**
438 438  
439 -|(% rowspan="2" style="text-align:center" %)F1.00|(% style="text-align:center" %)Start-up operation mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)00
440 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
464 +|(% rowspan="2" %)F1.00|Start-up operation mode|Factory default|00
465 +|Setting range|(% colspan="2" %)(((
441 441  LED ones place: Boot mode
442 442  
443 443  0: Start directly from the start frequency
... ... @@ -457,8 +457,9 @@
457 457  
458 458  Pre-excitation current, time and DC braking current, time share function code. If F1.09 pre-start braking time is set to 0, start from the start frequency. When the value is not set to 0, pre-excitation is implemented before startup to improve the dynamic response speed.
459 459  
460 -|(% rowspan="2" style="text-align:center" %)F1.01|(% style="text-align:center" %)Speed tracking mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
461 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
485 +
486 +|(% rowspan="2" %)F1.01|Speed tracking mode|Factory default|0
487 +|Setting range|(% colspan="2" %)(((
462 462  LED tens place: speed tracking direction
463 463  
464 464  0: One to the stop direction
... ... @@ -468,52 +468,72 @@
468 468  2: Automatic search
469 469  )))
470 470  
497 +
498 +
471 471  Ten: speed tracking direction
472 472  
473 473  This parameter determines the direction from which to start speed tracking. Please set it correctly according to the actual situation. If the setting is wrong, the startup may fail. In the case of not knowing the starting direction, you can set to automatic search, the program will automatically judge the starting direction, but the search time will be lengthened accordingly.
474 474  
475 -|(% rowspan="2" style="text-align:center" %)F1.02|(% style="text-align:center" %)Speed tracking time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)1.00s
476 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01 to 60.00s
477 477  
504 +|(% rowspan="2" %)F1.02|Speed tracking time|Factory default|1.00s
505 +|Setting range|(% colspan="2" %)0.01 to 60.00s
506 +
507 +
508 +
478 478  If the speed tracking time is too short, the tracking may end without tracking the actual frequency. At F1.01=002X, if the search direction is wrong, two searches will be performed and the actual search time will be doubled.
479 479  
480 -|(% rowspan="2" style="text-align:center" %)F1.03|(% style="text-align:center" %)Speed tracking current loop gain|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)10.00
481 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 10.00
482 -|(% rowspan="2" style="text-align:center" %)F1.04|(% style="text-align:center" %)(((
483 -RPM tracking speed gain
484 -)))|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)2.00
485 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01 to 10.00
486 486  
512 +|(% rowspan="2" %)F1.03|Speed tracking current loop gain|Factory default|10.00
513 +|Setting range|(% colspan="2" %)0.00 to 10.00
514 +|(% rowspan="2" %)F1.04|(((
515 +RPM tracking
516 +
517 +speed gain
518 +)))|Factory default|2.00
519 +|Setting range|(% colspan="2" %)0.01 to 10.00
520 +
521 +
522 +
487 487  The excitation search current loop gain and velocity loop gain are determined.
488 488  
489 -|(% rowspan="2" style="text-align:center" %)F1.05|(% style="text-align:center" %)Speed tracking current|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)150%
490 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)50% to 200%
491 491  
526 +|(% rowspan="2" %)F1.05|Speed tracking current|Factory default|150%
527 +|Setting range|(% colspan="2" %)50% to 200%
528 +
529 +
530 +
492 492  Set the excitation search current size.
493 493  
494 -|(% rowspan="2" style="text-align:center" %)F1.06|(% style="text-align:center" %)Starting frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
495 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 60.00Hz
496 -|(% rowspan="2" style="text-align:center" %)F1.07|(% style="text-align:center" %)Startup frequency duration|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.0s
497 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0 to 50.0s
533 +|(% rowspan="2" %)F1.06|Starting frequency|Factory default|0.00Hz
534 +|Setting range|(% colspan="2" %)0.0s to 60.00Hz
535 +|(% rowspan="2" %)F1.07|Startup frequency duration|Factory default|0.0s
536 +|Setting range|(% colspan="2" %)0.0 to 50.0s
498 498  
499 -In order to ensure the torque during startup, please use the appropriate startup frequency. In addition, the magnetic flux is established when waiting for the motor to start, so that the starting frequency is maintained for a certain time before accelerating. The starting frequency is maintained for a certain time before accelerating. The startup frequency F1.06 is not limited by the lower frequency. If the frequency given less than startup frequency, the AC driver can no be started, and it will standby state. The startup frequency holding time is not work during forward/reverse switching. The holding time is not included in the acceleration time, but is included in the running time of the simple PLC.
500 500  
501 -|(% rowspan="2" style="text-align:center" %)F1.08|(% style="text-align:center" %)Braking current before starting|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)80.0%
502 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0 to 150.0%
503 -|(% rowspan="2" style="text-align:center" %)F1.09|(% style="text-align:center" %)Braking time before starting|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.0s
504 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0 to 60.0s
505 505  
540 +In order to ensure the torque during startup, please use the appropriate startup frequency.In addition, the magnetic flux is established when waiting for the motor to start, so that the starting frequency is maintained for a certain time before accelerating.The starting frequency is maintained for a certain time before accelerating. The startup frequency F1.06 is not limited by the lower frequency. If the frequency given less than startup frequency, the AC driver can no be started, and it will standby state.The startup frequency holding time is not work during forward/reverse switching. The holding time is not included in the acceleration time, but is included in the running time of the simple PLC.
541 +
542 +|(% rowspan="2" %)F1.08|Braking current before starting|Factory default|80.0%
543 +|Setting range|(% colspan="2" %)0.0 to 150.0%
544 +|(% rowspan="2" %)F1.09|Braking time before starting|Factory default|0.0s
545 +|Setting range|(% colspan="2" %)0.0 to 60.0s
546 +
547 +
548 +
506 506  Starting DC braking is generally used to stop the motor completely before starting.
507 507  
508 508  If the starting mode is starting after the DC braking, the AC driver will execute the DC braking as the setting value, and it will start running after the setting starting braking time value. It will direct start without DC braking if the setting DC braking time is 0. The braking power is greater with the greater DC braking current.
509 509  
510 -|(% rowspan="2" style="text-align:center" %)F1.10|(% style="text-align:center" %)Shutdown mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
511 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:left" %)(((
553 +
554 +|(% rowspan="2" %)F1.10|Shutdown mode|Factory default|0
555 +|Setting range|(% colspan="2" %)(((
512 512  0: Slow down stop
513 513  
514 514  1: Free stop
515 515  )))
516 516  
561 +
562 +
517 517  0: Slow down stop
518 518  
519 519  After the stop command is effective, the inverter reduces the output frequency according to the deceleration mode and the defined acceleration and deceleration time, and stops after the frequency drops to 0.
... ... @@ -522,40 +522,41 @@
522 522  
523 523  When the stop command is valid, the inverter terminates output immediately. The load stops freely according to mechanical inertia.
524 524  
525 -|(% rowspan="2" style="text-align:center" %)F1.11|(% style="text-align:center" %)Stop DC braking start frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
526 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00Hz to Maximum frequency F0.10
527 -|(% rowspan="2" style="text-align:center" %)F1.12|(% style="text-align:center" %)Stop DC braking wait time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.0s
528 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 100.0s
529 -|(% rowspan="2" style="text-align:center" %)F1.13|(% style="text-align:center" %)Stop DC braking current|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)80.0%
530 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0% to 150%
531 -|(% rowspan="2" style="text-align:center" %)F1.14|(% style="text-align:center" %)Stop DC braking duration|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.0s
532 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 100.0s
571 +|(% rowspan="2" %)F1.11|Stop DC braking start frequency|Factory default|0.00Hz
572 +|Setting range|(% colspan="2" %)0.00Hz to Maximum frequency F0.10
573 +|(% rowspan="2" %)F1.12|Stop DC braking wait time|Factory default|0.0s
574 +|Setting range|(% colspan="2" %)0.0s to 100.0s
575 +|(% rowspan="2" %)F1.13|Stop DC braking current|Factory default|80.0%
576 +|Setting range|(% colspan="2" %)0%-150%
577 +|(% rowspan="2" %)F1.14|Stop DC braking duration|Factory default|0.0s
578 +|Setting range|(% colspan="2" %)0.0s to 100.0s
533 533  
580 +
581 +
534 534  DC braking start frequency: slow down the stopping process. When the output frequency is less than this frequency, the DC braking process starts to stop.
535 535  
536 -DC braking waiting time: When the output frequency is reduced to F1.11 DC braking starting frequency, the inverter stops output and starts timing. After the delay time set by F1.12, DC braking starts again. Used to prevent over current failure caused by DC braking at high speeds.
584 +Dc braking waiting time: When the output frequency is reduced to F1.11 DC braking starting frequency, the inverter stops output and starts timing. After the delay time set by F1.12, DC braking starts again. Used to prevent over current failure caused by DC braking at high speeds.
537 537  
538 538  Stop DC braking current: refers to the amount of DC braking applied. The greater the value, the stronger the DC braking effect.
539 539  
540 -DC braking time: the time added to the DC braking amount. When this value is 0, it means that there is no DC braking process, and the inverter stops according to the set deceleration stop process.
588 +Dc braking time: the time added to the DC braking amount. When this value is 0, it means that there is no DC braking process, and the inverter stops according to the set deceleration stop process.
541 541  
542 -(% style="text-align:center" %)
543 -(((
544 -(% style="display:inline-block" %)
545 -[[Figure 9-1-1 Shutdown DC braking diagram>>image:1763024398600-482.png]]
546 -)))
590 +[[image:file:///C:\Users\Administrator\AppData\Local\Temp\ksohtml13344\wps11.jpg]]
547 547  
548 -|(% rowspan="2" style="text-align:center" %)F1.16|(% style="text-align:center" %)Energy consumption brake action voltage|(% style="text-align:center" %)Factory default|Model-based setting
549 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)115.0% to 140.0%
592 +Figure 9-1-1 Shutdown DC braking diagram
550 550  
594 +
595 +|(% rowspan="2" %)F1.16|Energy consumption brake action voltage|Factory default|Model-based setting
596 +|Setting range|(% colspan="2" %)115.0% to 140.0%
597 +
551 551  Set the brake resistance operating voltage. When the relative value of the bus voltage is higher than this value, the brake resistance starts braking.
552 552  
553 -|(% rowspan="2" style="text-align:center" %)F1.17|(% style="text-align:center" %)Magnetic flux braking gain|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)80%
554 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)10% to 500%
555 -|(% rowspan="2" style="text-align:center" %)F1.18|(% style="text-align:center" %)Magnetic flux braking operating voltage|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model-based setting
556 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)110% to 150%
557 -|(% rowspan="2" style="text-align:center" %)F1.19|(% style="text-align:center" %)Flux brake limiting|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)20%
558 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0 to 200%
600 +|(% rowspan="2" %)F1.17|Magnetic flux braking gain|Factory default|80%
601 +|Setting range|(% colspan="2" %)10% to 500%
602 +|(% rowspan="2" %)F1.18|Magnetic flux braking operating voltage|Factory default|Model-based setting
603 +|Setting range|(% colspan="2" %)110% to 150%
604 +|(% rowspan="2" %)F1.19|Flux brake limiting|Factory default|20%
605 +|Setting range|(% colspan="2" %)0 to 200%
559 559  
560 560  When the motor decelerates the feedback energy, opening the flux brake can consume the feedback energy on the motor, so as to achieve rapid deceleration of the motor. This function is only effective in asynchronous motor VF control, and turning on this function will correspondingly increase motor loss and motor temperature rise.
561 561  
... ... @@ -565,36 +565,43 @@
565 565  
566 566  Flux brake limiting: The upper limit of the flux brake voltage, which may cause the output current of the inverter to be too high.
567 567  
568 -|(% rowspan="2" style="text-align:center" %)F1.20|Acceleration and deceleration selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
569 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
615 +|(% rowspan="2" %)F1.20|Acceleration and deceleration selection|Factory default|0
616 +|Setting range|(% colspan="2" %)(((
570 570  0: Straight line
571 571  
572 572  1: S curve
573 573  )))
574 574  
622 +
623 +
575 575  0: Straight line, generally suitable for general purpose load.
576 576  
577 577  1: S-curve, S-type acceleration and deceleration curve is mainly provided for the load that needs to slow down noise and vibration during acceleration and deceleration, reduce start-stop impact, or decrease torque at low frequency, and short-time acceleration at high frequency. If an over current or over load failure occurs at startup, reduce the set value of [F1.21].
578 578  
579 -|(% rowspan="2" style="text-align:center" %)F1.21|(% style="text-align:center" %)S-curve initial acceleration rate|(% style="text-align:center" %)Factory default|50.0%
580 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)20.0% to 100.0%
581 -|(% rowspan="2" style="text-align:center" %)F1.22|(% style="text-align:center" %)S-curve initial deceleration rate|(% style="text-align:center" %)Factory default|50.0%
582 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)20.0% to 100.0%
583 583  
629 +|(% rowspan="2" %)F1.21|S-curve initial acceleration rate|Factory default|50.0%
630 +|Setting range|(% colspan="2" %)20.0%-100.0%
631 +|(% rowspan="2" %)F1.22|S-curve initial deceleration rate|Factory default|50.0%
632 +|Setting range|(% colspan="2" %)20.0%-100.0%
633 +
584 584  S-curve Initial acceleration rate: The rate at which the acceleration process begins to increase in frequency. The smaller the initial acceleration rate, the more curved the S-curve of the acceleration process, whereas the larger the initial acceleration rate, the closer the acceleration S-curve to a straight line. To make the acceleration curve softer, you can reduce the initial acceleration rate and extend the acceleration time.
585 585  
586 -|(% rowspan="2" style="text-align:center" %)F1.23|(% style="text-align:center" %)Zero speed holding torque|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
587 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0% to 150.0%
636 +|(% rowspan="2" %)F1.23|Zero speed holding torque|Factory default|0
637 +|Setting range|(% colspan="2" %)0.0% to 150.0%
588 588  
639 +
640 +
589 589  Set the output torque of the inverter at zero speed. If the torque setting is large or the duration is long, attention should be paid to the heat dissipation of the motor.
590 590  
591 -|(% rowspan="2" style="text-align:center" %)F1.24|(% style="text-align:center" %)Zero speed holding torque time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model setting
592 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)(((
643 +|(% rowspan="2" %)F1.24|Zero speed holding torque time|Factory default|Model setting
644 +|Setting range|(% colspan="2" %)(((
593 593  0.0 to 6000.0s
594 594  
595 595  If the value is set to 6000.0s, the value remains unchanged without time limitation
596 596  )))
597 597  
650 +
651 +
598 598  Set the torque holding time when the inverter is running at zero speed. The timing starts when the operating frequency is 0Hz, and the inverter stops output after the time reaches the set zero-speed holding torque time. Among them, the effective timing value is 0 to 5999.9s, and the parameters are set in the effective timing value of the VFD at the set time. After the time is full, the VFD terminates and maintains the zero-speed torque.
599 599  
600 600  If the parameter setting is equal to 6000.0s, the VFD is not timed and defaults to long-term validity, and the zero-speed torque holding is terminated only after the stop command is given or the non-zero operating frequency is given.
... ... @@ -601,18 +601,18 @@
601 601  
602 602  Setting an appropriate zero-speed holding torque time can effectively achieve energy saving and protect the motor.
603 603  
604 -|(% rowspan="2" style="text-align:center" %)F1.25|(% style="text-align:center" %)Start pre-excitation time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.20
605 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 60.00s
658 +|(% rowspan="2" %)F1.25|Start pre-excitation time|Factory default|0.20
659 +|Setting range|(% colspan="2" %)0.00 to 60.00s
606 606  
607 607  This parameter is only valid if F0.00=0, in the open loop vector start, appropriate pre-excitation can make the start smoother.
608 608  
609 -|(% rowspan="2" style="text-align:center" %)F1.26|(% style="text-align:center" %)Shutdown frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
610 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 60.00Hz
663 +|(% rowspan="2" %)F1.26|Shutdown frequency|Factory default|0.00Hz
664 +|Setting range|(% colspan="2" %)0.00-60.00Hz
611 611  
612 612  This function is defined as the frequency of the minimum output of the inverter, less than this frequency, the output of the inverter stops.
613 613  
614 -|(% rowspan="2" style="text-align:center" %)F1.27|(% style="text-align:center" %)Power failure restart action selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
615 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
668 +|(% rowspan="2" %)F1.27|Power failure restart action selection|Factory default|0
669 +|Setting range|(% colspan="2" %)(((
616 616  0: Invalid
617 617  
618 618  1: Valid
... ... @@ -622,13 +622,14 @@
622 622  
623 623  1: Valid If the inverter is in operation before the power is cut off, the inverter will automatically start after the power is restored and after the set waiting time (set by [F1.28]). During the waiting time of power failure and restart, the inverter does not accept the running command, but if the stop command is entered during this period, the inverter will release the restart state.
624 624  
625 -|(% rowspan="2" style="text-align:center" %)F1.28|(% style="text-align:center" %)Power failure restart waiting time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.50s
626 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 120.00s
679 +|(% rowspan="2" %)F1.28|Power failure restart waiting time|Factory default|0.50s
680 +|Setting range|(% colspan="2" %)0.00 to 120.00s
627 627  
628 628  When [F1.27] setting is effective, After the inverter power supply, it will wait for the time set in [F1.28] to start running.
629 629  
630 -|(% rowspan="2" style="text-align:center" %)F1.29|(% style="text-align:center" %)Select the terminal running protection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)11
631 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
684 +
685 +|(% rowspan="2" %)F1.29|Select the terminal running protection|Factory default|11
686 +|Setting range|(% colspan="2" %)(((
632 632  LED units digital: Select the terminal run instruction when powering on.
633 633  
634 634  0: The terminal running instruction is invalid during power-on.
... ... @@ -644,6 +644,7 @@
644 644  
645 645  When terminal operation is selected, the initial wiring state of peripheral devices may affect the safety of the device. This parameter provides protective measures for terminal operation.
646 646  
702 +
647 647  LED units place: Select the terminal run command when powering on
648 648  
649 649  Select the mode of executing the operation instruction when the inverter is powered on with the terminal running signal in effect.
... ... @@ -660,10 +660,11 @@
660 660  
661 661  1: When the terminal instruction is effective, the terminal control can be started directly.
662 662  
663 -== **F2 group motor parameters** ==
664 664  
665 -|(% rowspan="2" style="text-align:center" %)F2.00|(% style="text-align:center" %)Motor type|(% style="text-align:center" %)Factory default|0
666 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
720 +**F2 group motor parameters**
721 +
722 +|(% rowspan="2" %)F2.00|Motor type|Factory default|0
723 +|Setting range|(% colspan="2" %)(((
667 667  0: Asynchronous motor (AM)
668 668  
669 669  1: Permanent magnet synchronous motor (PM)
... ... @@ -673,41 +673,41 @@
673 673  
674 674  2 Single-phase asynchronous motor refers to a single-phase motor without phase shift capacitance, U terminal is connected to the main winding, V terminal is connected to the common end, and W terminal is connected to the auxiliary winding.
675 675  
676 -(% style="width:875px" %)
677 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.01|(% colspan="2" style="text-align:center" %)Rated power of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
678 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.1kW to 400.0kW
679 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.02|(% colspan="2" style="text-align:center" %)Rated voltage of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
680 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)1V to 440V
681 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.03|(% colspan="2" style="text-align:center" %)Rated current of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
682 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.1A to 2000.0A
683 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.04|(% colspan="2" style="text-align:center" %)Rated power of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
684 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.00Hz to Maximum frequency F0.10
685 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.05|(% colspan="2" style="text-align:center" %)Rated motor speed|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
686 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)1rpm to 65000rpm
687 -|(% colspan="8" %)**✎Note:**(((
733 +| |(% rowspan="2" %)F2.01|(% colspan="2" %)Rated power of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
734 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.1kW to 400.0kW|
735 +| |(% rowspan="2" %)F2.02|(% colspan="2" %)Rated voltage of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
736 +| |(% colspan="2" %)Setting range|(% colspan="4" %)1V to 440V|
737 +| |(% rowspan="2" %)F2.03|(% colspan="2" %)Rated current of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
738 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.1A to 2000.0A|
739 +| |(% rowspan="2" %)F2.04|(% colspan="2" %)Rated power of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
740 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.00Hz-Maximum frequency F0.10|
741 +| |(% rowspan="2" %)F2.05|(% colspan="2" %)Rated motor speed|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
742 +| |(% colspan="2" %)Setting range|(% colspan="4" %)1rpm to 65000rpm|
743 +|(% colspan="8" %)**Note:**|
744 +|(% colspan="8" %)(((
688 688  1. Please set according to the nameplate parameters of the motor.
689 689  
690 690  2. The excellent control performance of vector control requires accurate motor parameters, and accurate parameter identification comes from the correct setting of the rated parameters of the motor.
691 691  
692 692  3. In order to ensure the control performance, please configure the motor according to the inverter standard adaptation motor, if the motor power and the standard adaptation motor gap is too large, the control performance of the inverter will be significantly reduced.
693 -)))
694 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.06|(% colspan="2" style="text-align:center; width:493px" %)Motor stator resistance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
695 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.001Ω to 65.000Ω
696 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.07|(% colspan="2" style="text-align:center; width:493px" %)Motor rotor resistance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
697 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.001Ω to 65.000Ω
698 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.08|(% colspan="2" style="text-align:center; width:493px" %)Motor fixed rotor inductance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
699 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 6500.0mH
700 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.09|(% colspan="2" style="text-align:center; width:493px" %)Mutual inductance of motor fixed rotor|(% colspan="2" style="text-align:center" %)Factory default|Model determination
701 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 6500.0mH
702 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.10|(% colspan="2" style="text-align:center; width:493px" %)Motor no-load current|(% colspan="2" style="text-align:center" %)Factory default|Model determination
703 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 650.0A
750 +)))|
751 +|(% colspan="3" rowspan="2" %)F2.06|(% colspan="2" %)Motor stator resistance|(% colspan="2" %)Factory default|Model determination|
752 +|(% colspan="2" %)Setting range|(% colspan="3" %)0.001Ω to 65.000Ω|
753 +|(% colspan="3" rowspan="2" %)F2.07|(% colspan="2" %)Motor rotor resistance|(% colspan="2" %)Factory default|Model determination|
754 +|(% colspan="2" %)Setting range|(% colspan="3" %)0.001Ω to 65.000Ω|
755 +|(% colspan="3" rowspan="2" %)F2.08|(% colspan="2" %)Motor fixed rotor inductance|(% colspan="2" %)Factory default|Model determination|
756 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 6500.0mH
757 +|(% colspan="3" rowspan="2" %)F2.09|(% colspan="2" %)Mutual inductance of motor fixed rotor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination
758 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 6500.0mH
759 +|(% colspan="3" rowspan="2" %)F2.10|(% colspan="2" %)Motor no-load current|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination
760 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 650.0A
704 704  
705 705  After the automatic tuning of the asynchronous motor is completed normally, the set values of the asynchronous motor parameters (F2.06 to F2.10) are automatically updated.
706 706  
707 707  After changing the motor rated power F2.01 each time, the VFD F2.06 to F2.10 parameter values will automatically restore the default standard motor parameters, if running in vector mode, please re-tune.
708 708  
709 -|(% rowspan="2" style="text-align:center; width:135px" %)F2.11|(% style="text-align:center; width:266px" %)Tuning selection|(% style="text-align:center; width:202px" %)Factory default|(% style="text-align:center" %)0
710 -|(% style="text-align:center; width:266px" %)Setting range|(% colspan="2" style="width:231px" %)(((
766 +|(% rowspan="2" %)F2.11|Tuning selection|Factory default|0
767 +|Setting range|(% colspan="2" %)(((
711 711  0: No operation is performed
712 712  
713 713  1: Static tuning 1
... ... @@ -717,6 +717,8 @@
717 717  3: Static tuning 2 (AM calculated Lm)
718 718  )))
719 719  
777 +
778 +
720 720  Tip: Before tuning, you must set the correct motor type and rating parameters (F2.00 to F2.05).
721 721  
722 722  0: No operation is performed, that is, tuning is disabled.
... ... @@ -735,13 +735,15 @@
735 735  
736 736  Note: Tuning can only be effective in keyboard control mode, acceleration and deceleration time is recommended to use the factory default.
737 737  
738 -|(% rowspan="2" style="text-align:center" %)F2.12|(% style="text-align:center" %)G/P Machine type|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
739 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
740 -0: G-type machine;
797 +|(% rowspan="2" %)F2.12|G/P Machine type|Factory default|Model determination
798 +|Setting range|(% colspan="2" %)(((
799 +0: G type machine;
741 741  
742 742  1: P-type machine
743 743  )))
744 744  
804 +
805 +
745 745  This parameter can only be used to view factory models.
746 746  
747 747  1: Constant torque load for specified rated parameters.
... ... @@ -748,63 +748,73 @@
748 748  
749 749  2: Suitable for the specified rated parameters of the variable torque load (fan, pump load).
750 750  
751 -|(% rowspan="2" style="text-align:center" %)F2.13|(% style="text-align:center" %)Single phase asynchronous motor turns ratio|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)100%
752 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)10 to 200%
812 +|(% rowspan="2" %)F2.13|Single phase asynchronous motor turns ratio|Factory default|100%
813 +|Setting range|(% colspan="2" %)10 to 200%
753 753  
815 +
816 +
754 754  U terminal main winding, V terminal auxiliary winding, W common end, this parameter is used to set the ratio of the number of turns between the main winding and the auxiliary winding of the single-phase motor.
755 755  
756 -|(% rowspan="2" style="text-align:center" %)F2.14|(% style="text-align:center" %)Current calibration coefficient of single-phase motor|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)120%
757 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)50 to 200%
819 +|(% rowspan="2" %)F2.14|Current calibration coefficient of single-phase motor|Factory default|120%
820 +|Setting range|(% colspan="2" %)50 to 200%
758 758  
759 759  The single-phase motor has main and auxiliary windings, and the three-phase output current is unbalanced, so the output current displayed by the inverter needs to be multiplied by the coefficient of the resultant current.
760 760  
761 -|(% rowspan="2" style="text-align:center" %)F2.15|(% style="text-align:center; width:310px" %)Number of motor poles|(% style="text-align:center; width:167px" %)Factory default|(% style="text-align:center" %)4
762 -|(% style="text-align:center; width:310px" %)Setting range|(% colspan="2" style="text-align:center; width:215px" %)2 to 48
763 763  
825 +|(% rowspan="2" %)F2.15|Number of motor poles|Factory default|4
826 +|Setting range|(% colspan="2" %)2 to 48
827 +
828 +
829 +
764 764  Change F2.04 or F2.05, the program will automatically calculate the number of motor poles, in general, do not need to set this parameter.
765 765  
766 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.22|(% style="text-align:center; width:242px" %)Stator resistance of synchro|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
767 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.001 to 65.000(0.001Ohm)
768 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.23|(% style="text-align:center; width:242px" %)Synchro d-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
769 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.01mH to 655.35mH
770 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.24|(% style="text-align:center; width:242px" %)Synchro Q-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
771 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.01mH to 655.35mH
772 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.25|(% style="text-align:center; width:242px" %)Synchro back electromotive force|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
773 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.1V to 1000.0V
832 +|(% rowspan="2" %)F2.22|Stator resistance of synchro|Factory default|Model determination
833 +|Setting range|(% colspan="2" %)0.001 to 65.000(0.001Ohm)
834 +|(% rowspan="2" %)F2.23|Synchro d-axis inductance|Factory default|Model determination
835 +|Setting range|(% colspan="2" %)0.01mH-655.35mH
836 +|(% rowspan="2" %)F2.24|Synchro Q-axis inductance|Factory default|Model determination
837 +|Setting range|(% colspan="2" %)0.01mH to 655.35mH
838 +|(% rowspan="2" %)F2.25|Synchro back electromotive force|Factory default|Model determination
839 +|Setting range|(% colspan="2" %)0.1V to 1000.0V
774 774  
775 775  After the automatic tuning of the synchronous motor is completed, the set values of the synchronous motor parameters (F2.22 to F2.25) are automatically updated.
776 776  
777 777  After changing the rated motor power F2.01 each time, the F2.22 to F2.25 parameter values of the inverter will automatically restore the default standard motor parameters, please re-tune.
778 778  
779 -|(% rowspan="2" style="text-align:center" %)F2.28|(% style="text-align:center" %)High frequency injection voltage|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)20.0%
780 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1% to 100.0%
845 +|(% rowspan="2" %)F2.28|High frequency injection voltage|Factory default|20.0%
846 +|Setting range|(% colspan="2" %)0.1% to 100.0%
781 781  
848 +
849 +
782 782  The current injected when the synchronous motor learns the inductance of DQ axis by high frequency injection.
783 783  
784 -|(% rowspan="2" style="text-align:center" %)F2.29|(% style="text-align:center" %)Back potential identification current|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)50.0%
785 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1% to 100.0%
852 +|(% rowspan="2" %)F2.29|Back potential identification current|Factory default|50.0%
853 +|Setting range|(% colspan="2" %)0.1% to 100.0%
786 786  
855 +
856 +
787 787  The output current of the inverter is the size when the synchronous motor dynamically adjusts to learn the back potential.
788 788  
789 -|(% rowspan="2" style="text-align:center" %)F2.31|(% style="text-align:center" %)Asynchronous no-load current per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
790 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1%
791 -|(% rowspan="2" style="text-align:center" %)F2.32|(% style="text-align:center" %)Per unit asynchronous stator resistance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
792 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
793 -|(% rowspan="2" style="text-align:center" %)F2.33|(% style="text-align:center" %)Asynchronous rotor resistance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
794 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
795 -|(% rowspan="2" style="text-align:center" %)F2.34|(% style="text-align:center" %)Asynchronous mutual inductance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
796 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1%
797 -|(% rowspan="2" style="text-align:center" %)F2.35|(% style="text-align:center" %)Asynchronous leakage sensing per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
798 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
799 -|(% rowspan="2" style="text-align:center" %)F2.36|(% style="text-align:center" %)Per unit value of asynchronous leakage sensing coefficient|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
800 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
801 -|(% rowspan="2" style="text-align:center" %)F2.37|(% style="text-align:center" %)Synchronous stator resistance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
802 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
803 -|(% rowspan="2" style="text-align:center" %)F2.38|(% style="text-align:center" %)Per unit value of synchronous D-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
804 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
805 -|(% rowspan="2" style="text-align:center" %)F2.39|(% style="text-align:center" %)Synchronous Q-axis inductance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
806 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
807 -|(% rowspan="2" style="text-align:center" %)F2.40|(% style="text-align:center" %)Back electromotive force of synchronous motor|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
808 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1V
809 809  
810 -The per unit value of the motor parameters is used for the actual program calculation. After learning or parameter recovery, the actual change is F2.31 to F2.40. F2.06 to F2.10 and F2.22 to F2.25 are calculated from the per unit value, so only F2.31 to F2.40 values can be modified, F2.06 to F2.10 and F2.22 to F2.25 are only used to display and cannot be changed.
860 +|(% rowspan="2" %)F2.31|Asynchronous no-load current per unit value|Factory default|Model determination
861 +|Setting range|(% colspan="2" %)0.1%
862 +|(% rowspan="2" %)F2.32|Per unit asynchronous stator resistance|Factory default|Model determination
863 +|Setting range|(% colspan="2" %)0.01%
864 +|(% rowspan="2" %)F2.33|Asynchronous rotor resistance per unit value|Factory default|Model determination
865 +|Setting range|(% colspan="2" %)0.01%
866 +|(% rowspan="2" %)F2.34|Asynchronous mutual inductance per unit value|Factory default|Model determination
867 +|Setting range|(% colspan="2" %)0.1%
868 +|(% rowspan="2" %)F2.35|Asynchronous leakage sensing per unit value|Factory default|Model determination
869 +|Setting range|(% colspan="2" %)0.01%
870 +|(% rowspan="2" %)F2.36|Per unit value of asynchronous leakage sensing coefficient|Factory default|Model determination
871 +|Setting range|(% colspan="2" %)0.01%
872 +|(% rowspan="2" %)F2.37|Synchronous stator resistance per unit value|Factory default|Model determination
873 +|Setting range|(% colspan="2" %)0.01%
874 +|(% rowspan="2" %)F2.38|Per unit value of synchronous D-axis inductance|Factory default|Model determination
875 +|Setting range|(% colspan="2" %)0.01%
876 +|(% rowspan="2" %)F2.39|Synchronous Q-axis inductance per unit value|Factory default|Model determination
877 +|Setting range|(% colspan="2" %)0.01%
878 +|(% rowspan="2" %)F2.40|Back electromotive force of synchronous motor|Factory default|Model determination
879 +|Setting range|(% colspan="2" %)0.1V
880 +
881 +The per unit value of the motor parameters is used for the actual program calculation. After learning or parameter recovery, the actual change is F2.31-F2.40. F2.06-F2.10 and F2.22-F2.25 are calculated from the per unit value, so only F2.31-F2.40 values can be modified, F2.06-F2.10 and F2.22-F2.25 are only used to display and cannot be changed.
1763022484807-191.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022495845-910.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022525597-175.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022595008-156.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022599082-487.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022602360-885.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022605234-199.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -2.2 KB
Content
1763022734381-822.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -650.7 KB
Content
1763022752521-750.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -650.7 KB
Content
1763022803632-610.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -82.1 KB
Content
1763023714773-291.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -106.5 KB
Content
1763024398600-482.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -99.1 KB
Content