Skip to Content

Changes for page 09 Function code

Last modified by Iris on 2025/11/17 14:59
From version 6.1
edited by Iris
on 2025/11/13 17:40
Change comment: There is no comment for this version
To version 3.1
edited by Iris
on 2025/11/13 16:49
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,4 +1,4 @@
1 -== **F0 group basic function group** ==
1 +**F0 group basic function group**
2 2  
3 3  |(% rowspan="2" style="text-align:center" %)F0.00|(% style="text-align:center" %)Motor control mode|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)1
4 4  |(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
... ... @@ -128,13 +128,13 @@
128 128  The secondary frequency source Y is used in the same way as the primary frequency source X when it is used as an independent frequency given channel (that is, the frequency source selected to switch from X to Y).
129 129  
130 130  |(% rowspan="2" style="text-align:center" %)F0.05|(% style="width:344px" %)The auxiliary frequency source Y range is selected during superposition|(% style="text-align:center; width:142px" %)Factory default|(% style="text-align:center" %)0
131 -|(% style="text-align:center; width:344px" %)Setting range|(% colspan="2" style="width:228px" %)(((
131 +|(% style="width:344px" %)Setting range|(% colspan="2" style="width:228px" %)(((
132 132  0: Relative to the maximum frequency  F0.10
133 133  
134 134  1: Relative to the frequency source X
135 135  )))
136 -|(% rowspan="2" style="text-align:center" %)F0.06|(% style="width:344px" %)Auxiliary frequency source Y range in superposition|(% style="text-align:center; width:142px" %)Factory default|(% style="text-align:center" %)100%
137 -|(% style="text-align:center; width:344px" %)Setting range|(% colspan="2" style="text-align:center; width:228px" %)0% to 150%
136 +|(% rowspan="2" style="text-align:center" %)F0.06|(% style="width:344px" %)Auxiliary frequency source Y range in superposition|(% style="text-align:center; width:142px" %)Factory default|100%
137 +|(% style="width:344px" %)Setting range|(% colspan="2" style="text-align:center; width:228px" %)0% to 150%
138 138  
139 139  When the frequency source is selected as a frequency stack (F0.07 is set to 1, 3, or 4), it is used to determine the adjustment range of the auxiliary frequency source. F0.05 is used to determine the object relative to the range, if it is relative to the maximum frequency (F0.10), the range is a fixed value; If it is relative to the primary frequency source X, its range will change as the primary frequency source X changes.
140 140  
... ... @@ -169,7 +169,7 @@
169 169  
170 170  When the auxiliary frequency source for digital or pulse potentiometer timing, preset frequency (F0.08) does not work, through the keyboard ▲/▼ key (or multi-function input terminal UP, DOWN) can be adjusted on the basis of the main given frequency.
171 171  
172 -When the auxiliary frequency source is given as an analog input (AI1, AI2) or a pulse input, 100% of the input setting corresponds to the auxiliary frequency source range (see F0.05 and F0.06 instructions). If you need to adjust up or down from the main given frequency, set the analog input to a range of n% to +n%.
172 +When the auxiliary frequency source is given as an analog input (AI1, AI2) or a pulse input, 100% of the input setting corresponds to the auxiliary frequency source range (see F0.05 and F0.06 instructions). If you need to adjust up or down from the main given frequency, set the analog input to a range of.n% to +n%.
173 173  
174 174  The frequency source is timed for pulse input, similar to analog quantity setting.
175 175  
... ... @@ -265,11 +265,11 @@
265 265  
266 266  The effect of adjusting the carrier frequency on the following performance:
267 267  
268 -|(% style="text-align:center" %)Carrier frequency|(% style="text-align:center" %)Low [[image:1763022484807-191.png]] High
268 +|(% style="text-align:center" %)Carrier frequency|(% style="text-align:center" %)Low[[image:1763022484807-191.png]]High
269 269  |(% style="text-align:center" %)Motor noise|(% style="text-align:center" %)High [[image:1763022495845-910.png]] Low
270 -|(% style="text-align:center" %)The output current waveform|(% style="text-align:center" %)Worse [[image:1763022525597-175.png]] Better
271 -|(% style="text-align:center" %)Temperature rise in electric motors|(% style="text-align:center" %)High [[image:1763022595008-156.png]] Low
272 -|(% style="text-align:center" %)VFD temperature rise|(% style="text-align:center" %)Low [[image:1763022599082-487.png]] High
270 +|(% style="text-align:center" %)The output current waveform|(% style="text-align:center" %)Worse[[image:1763022525597-175.png]]Better
271 +|(% style="text-align:center" %)Temperature rise in electric motors|(% style="text-align:center" %)High[[image:1763022595008-156.png]]Low
272 +|(% style="text-align:center" %)VFD temperature rise|(% style="text-align:center" %)Low[[image:1763022599082-487.png]]High
273 273  |(% style="text-align:center" %)Leak current|(% style="text-align:center" %)Low[[image:1763022602360-885.png]]High
274 274  |(% style="text-align:center" %)External radiation interference|(% style="text-align:center" %)Low[[image:1763022605234-199.png]]High
275 275  
... ... @@ -318,7 +318,7 @@
318 318  
319 319  When the output frequency is low, reducing the PWM carrier can increase the low frequency starting torque and reduce the electromagnetic interference during starting. When the bit is 1, the program automatically reduces the PWM carrier when the output frequency is low.
320 320  
321 -Hundreds place: Random PWM depth
321 +Hundreds palce: Random PWM depth
322 322  
323 323  In order to make the motor noise spectrum flatter, you can turn on the random PWM function, after the function is turned on, the PWM carrier is no longer a fixed value, but fluctuates around the F0.16 set carrier. When the bit is not 0, the random PWM function works. The larger the value, the wider the fluctuation range and the flatter the noise spectrum. It should be noted that after opening the random carrier, the electromagnetic noise of the motor will not necessarily be reduced, and the actual noise perception varies from person to person.
324 324  
... ... @@ -332,8 +332,8 @@
332 332  
333 333  (% style="text-align:center" %)
334 334  (((
335 -(% style="display:inline-block; width:616px;" %)
336 -[[Figure 9-0-1 Acceleration and deceleration time>>image:1763022803632-610.png||height="370" width="616"]]
335 +(% style="display:inline-block" %)
336 +[[Figure 9-0-1 Acceleration and deceleration time>>image:1763022803632-610.png]]
337 337  )))
338 338  
339 339  Note the difference between the actual acceleration and deceleration time and the set acceleration and deceleration time.
... ... @@ -352,9 +352,9 @@
352 352  
353 353  |(% rowspan="2" style="text-align:center" %)F0.20|(% style="text-align:center" %)Parameter initialization|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
354 354  |(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
355 -0: No operation
355 +0: No opreration
356 356  
357 -1: Restore factory default (Do not restore motor parameters)
357 +1: Restore factorydefault (Do not restore motor parameters)
358 358  
359 359  2: Clear the record information
360 360  
... ... @@ -384,8 +384,8 @@
384 384  
385 385  Note the following function codes: F0.18, F0.19, F8.01, F8.02, F8.03, F8.04, F8.05, F8.06, F8.07, F8.08.
386 386  
387 -|(% rowspan="2" style="text-align:center" %)F0.24|(% style="text-align:center; width:382px" %)Acceleration and deceleration time reference frequency|(% style="text-align:center; width:147px" %)Factory default|(% style="text-align:center; width:33px" %)0
388 -|(% style="text-align:center; width:382px" %)Setting range|(% colspan="2" style="width:180px" %)(((
387 +|(% rowspan="2" %)F0.24|Acceleration and deceleration time reference frequency|Factory default|0
388 +|Setting range|(% colspan="2" %)(((
389 389  0: Maximum frequency (F0.10)
390 390  
391 391  1: Set the frequency
... ... @@ -397,7 +397,7 @@
397 397  
398 398  |(% rowspan="2" style="text-align:center" %)F0.25|(% style="text-align:center" %)Fan control|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)01
399 399  |(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
400 -One place: Start/stop control
400 +One place: start/stop control
401 401  
402 402  0: The fan runs after the inverter is powered on
403 403  
... ... @@ -420,6 +420,7 @@
420 420  
421 421  Speed control: Below 45°C: Operate at 50% speed; From 45°C to 50°C: Operate at 75% speed; At 50°C and above: Operate at 100% speed.
422 422  
423 +
423 423  |(% rowspan="2" style="text-align:center" %)F0.26|(% style="text-align:center" %)Frequency command decimal point|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)2
424 424  |(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)(((
425 425  1: 1 decimal places
... ... @@ -480,7 +480,9 @@
480 480  |(% rowspan="2" style="text-align:center" %)F1.03|(% style="text-align:center" %)Speed tracking current loop gain|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)10.00
481 481  |(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 10.00
482 482  |(% rowspan="2" style="text-align:center" %)F1.04|(% style="text-align:center" %)(((
483 -RPM tracking speed gain
484 +RPM tracking
485 +
486 +speed gain
484 484  )))|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)2.00
485 485  |(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01 to 10.00
486 486  
... ... @@ -531,31 +531,32 @@
531 531  |(% rowspan="2" style="text-align:center" %)F1.14|(% style="text-align:center" %)Stop DC braking duration|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.0s
532 532  |(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0s to 100.0s
533 533  
537 +
538 +
534 534  DC braking start frequency: slow down the stopping process. When the output frequency is less than this frequency, the DC braking process starts to stop.
535 535  
536 -DC braking waiting time: When the output frequency is reduced to F1.11 DC braking starting frequency, the inverter stops output and starts timing. After the delay time set by F1.12, DC braking starts again. Used to prevent over current failure caused by DC braking at high speeds.
541 +Dc braking waiting time: When the output frequency is reduced to F1.11 DC braking starting frequency, the inverter stops output and starts timing. After the delay time set by F1.12, DC braking starts again. Used to prevent over current failure caused by DC braking at high speeds.
537 537  
538 538  Stop DC braking current: refers to the amount of DC braking applied. The greater the value, the stronger the DC braking effect.
539 539  
540 540  DC braking time: the time added to the DC braking amount. When this value is 0, it means that there is no DC braking process, and the inverter stops according to the set deceleration stop process.
541 541  
542 -(% style="text-align:center" %)
543 -(((
544 -(% style="display:inline-block" %)
545 -[[Figure 9-1-1 Shutdown DC braking diagram>>image:1763024398600-482.png]]
546 -)))
547 +[[image:1763022599082-487.png]]
547 547  
548 -|(% rowspan="2" style="text-align:center" %)F1.16|(% style="text-align:center" %)Energy consumption brake action voltage|(% style="text-align:center" %)Factory default|Model-based setting
549 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)115.0% to 140.0%
549 +Figure 9-1-1 Shutdown DC braking diagram
550 550  
551 +
552 +|(% rowspan="2" %)F1.16|Energy consumption brake action voltage|Factory default|Model-based setting
553 +|Setting range|(% colspan="2" %)115.0% to 140.0%
554 +
551 551  Set the brake resistance operating voltage. When the relative value of the bus voltage is higher than this value, the brake resistance starts braking.
552 552  
553 -|(% rowspan="2" style="text-align:center" %)F1.17|(% style="text-align:center" %)Magnetic flux braking gain|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)80%
554 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)10% to 500%
555 -|(% rowspan="2" style="text-align:center" %)F1.18|(% style="text-align:center" %)Magnetic flux braking operating voltage|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model-based setting
556 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)110% to 150%
557 -|(% rowspan="2" style="text-align:center" %)F1.19|(% style="text-align:center" %)Flux brake limiting|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)20%
558 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0 to 200%
557 +|(% rowspan="2" %)F1.17|Magnetic flux braking gain|Factory default|80%
558 +|Setting range|(% colspan="2" %)10% to 500%
559 +|(% rowspan="2" %)F1.18|Magnetic flux braking operating voltage|Factory default|Model-based setting
560 +|Setting range|(% colspan="2" %)110% to 150%
561 +|(% rowspan="2" %)F1.19|Flux brake limiting|Factory default|20%
562 +|Setting range|(% colspan="2" %)0 to 200%
559 559  
560 560  When the motor decelerates the feedback energy, opening the flux brake can consume the feedback energy on the motor, so as to achieve rapid deceleration of the motor. This function is only effective in asynchronous motor VF control, and turning on this function will correspondingly increase motor loss and motor temperature rise.
561 561  
... ... @@ -565,36 +565,43 @@
565 565  
566 566  Flux brake limiting: The upper limit of the flux brake voltage, which may cause the output current of the inverter to be too high.
567 567  
568 -|(% rowspan="2" style="text-align:center" %)F1.20|Acceleration and deceleration selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
569 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
572 +|(% rowspan="2" %)F1.20|Acceleration and deceleration selection|Factory default|0
573 +|Setting range|(% colspan="2" %)(((
570 570  0: Straight line
571 571  
572 572  1: S curve
573 573  )))
574 574  
579 +
580 +
575 575  0: Straight line, generally suitable for general purpose load.
576 576  
577 577  1: S-curve, S-type acceleration and deceleration curve is mainly provided for the load that needs to slow down noise and vibration during acceleration and deceleration, reduce start-stop impact, or decrease torque at low frequency, and short-time acceleration at high frequency. If an over current or over load failure occurs at startup, reduce the set value of [F1.21].
578 578  
579 -|(% rowspan="2" style="text-align:center" %)F1.21|(% style="text-align:center" %)S-curve initial acceleration rate|(% style="text-align:center" %)Factory default|50.0%
580 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)20.0% to 100.0%
581 -|(% rowspan="2" style="text-align:center" %)F1.22|(% style="text-align:center" %)S-curve initial deceleration rate|(% style="text-align:center" %)Factory default|50.0%
582 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)20.0% to 100.0%
583 583  
586 +|(% rowspan="2" %)F1.21|S-curve initial acceleration rate|Factory default|50.0%
587 +|Setting range|(% colspan="2" %)20.0%-100.0%
588 +|(% rowspan="2" %)F1.22|S-curve initial deceleration rate|Factory default|50.0%
589 +|Setting range|(% colspan="2" %)20.0%-100.0%
590 +
584 584  S-curve Initial acceleration rate: The rate at which the acceleration process begins to increase in frequency. The smaller the initial acceleration rate, the more curved the S-curve of the acceleration process, whereas the larger the initial acceleration rate, the closer the acceleration S-curve to a straight line. To make the acceleration curve softer, you can reduce the initial acceleration rate and extend the acceleration time.
585 585  
586 -|(% rowspan="2" style="text-align:center" %)F1.23|(% style="text-align:center" %)Zero speed holding torque|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
587 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.0% to 150.0%
593 +|(% rowspan="2" %)F1.23|Zero speed holding torque|Factory default|0
594 +|Setting range|(% colspan="2" %)0.0% to 150.0%
588 588  
596 +
597 +
589 589  Set the output torque of the inverter at zero speed. If the torque setting is large or the duration is long, attention should be paid to the heat dissipation of the motor.
590 590  
591 -|(% rowspan="2" style="text-align:center" %)F1.24|(% style="text-align:center" %)Zero speed holding torque time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model setting
592 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)(((
600 +|(% rowspan="2" %)F1.24|Zero speed holding torque time|Factory default|Model setting
601 +|Setting range|(% colspan="2" %)(((
593 593  0.0 to 6000.0s
594 594  
595 595  If the value is set to 6000.0s, the value remains unchanged without time limitation
596 596  )))
597 597  
607 +
608 +
598 598  Set the torque holding time when the inverter is running at zero speed. The timing starts when the operating frequency is 0Hz, and the inverter stops output after the time reaches the set zero-speed holding torque time. Among them, the effective timing value is 0 to 5999.9s, and the parameters are set in the effective timing value of the VFD at the set time. After the time is full, the VFD terminates and maintains the zero-speed torque.
599 599  
600 600  If the parameter setting is equal to 6000.0s, the VFD is not timed and defaults to long-term validity, and the zero-speed torque holding is terminated only after the stop command is given or the non-zero operating frequency is given.
... ... @@ -601,18 +601,18 @@
601 601  
602 602  Setting an appropriate zero-speed holding torque time can effectively achieve energy saving and protect the motor.
603 603  
604 -|(% rowspan="2" style="text-align:center" %)F1.25|(% style="text-align:center" %)Start pre-excitation time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.20
605 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 60.00s
615 +|(% rowspan="2" %)F1.25|Start pre-excitation time|Factory default|0.20
616 +|Setting range|(% colspan="2" %)0.00 to 60.00s
606 606  
607 607  This parameter is only valid if F0.00=0, in the open loop vector start, appropriate pre-excitation can make the start smoother.
608 608  
609 -|(% rowspan="2" style="text-align:center" %)F1.26|(% style="text-align:center" %)Shutdown frequency|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.00Hz
610 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 60.00Hz
620 +|(% rowspan="2" %)F1.26|Shutdown frequency|Factory default|0.00Hz
621 +|Setting range|(% colspan="2" %)0.00-60.00Hz
611 611  
612 612  This function is defined as the frequency of the minimum output of the inverter, less than this frequency, the output of the inverter stops.
613 613  
614 -|(% rowspan="2" style="text-align:center" %)F1.27|(% style="text-align:center" %)Power failure restart action selection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0
615 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
625 +|(% rowspan="2" %)F1.27|Power failure restart action selection|Factory default|0
626 +|Setting range|(% colspan="2" %)(((
616 616  0: Invalid
617 617  
618 618  1: Valid
... ... @@ -622,13 +622,14 @@
622 622  
623 623  1: Valid If the inverter is in operation before the power is cut off, the inverter will automatically start after the power is restored and after the set waiting time (set by [F1.28]). During the waiting time of power failure and restart, the inverter does not accept the running command, but if the stop command is entered during this period, the inverter will release the restart state.
624 624  
625 -|(% rowspan="2" style="text-align:center" %)F1.28|(% style="text-align:center" %)Power failure restart waiting time|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)0.50s
626 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.00 to 120.00s
636 +|(% rowspan="2" %)F1.28|Power failure restart waiting time|Factory default|0.50s
637 +|Setting range|(% colspan="2" %)0.00 to 120.00s
627 627  
628 628  When [F1.27] setting is effective, After the inverter power supply, it will wait for the time set in [F1.28] to start running.
629 629  
630 -|(% rowspan="2" style="text-align:center" %)F1.29|(% style="text-align:center" %)Select the terminal running protection|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)11
631 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
641 +
642 +|(% rowspan="2" %)F1.29|Select the terminal running protection|Factory default|11
643 +|Setting range|(% colspan="2" %)(((
632 632  LED units digital: Select the terminal run instruction when powering on.
633 633  
634 634  0: The terminal running instruction is invalid during power-on.
... ... @@ -644,6 +644,7 @@
644 644  
645 645  When terminal operation is selected, the initial wiring state of peripheral devices may affect the safety of the device. This parameter provides protective measures for terminal operation.
646 646  
659 +
647 647  LED units place: Select the terminal run command when powering on
648 648  
649 649  Select the mode of executing the operation instruction when the inverter is powered on with the terminal running signal in effect.
... ... @@ -660,10 +660,11 @@
660 660  
661 661  1: When the terminal instruction is effective, the terminal control can be started directly.
662 662  
663 -== **F2 group motor parameters** ==
664 664  
665 -|(% rowspan="2" style="text-align:center" %)F2.00|(% style="text-align:center" %)Motor type|(% style="text-align:center" %)Factory default|0
666 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
677 +**F2 group motor parameters**
678 +
679 +|(% rowspan="2" %)F2.00|Motor type|Factory default|0
680 +|Setting range|(% colspan="2" %)(((
667 667  0: Asynchronous motor (AM)
668 668  
669 669  1: Permanent magnet synchronous motor (PM)
... ... @@ -673,41 +673,41 @@
673 673  
674 674  2 Single-phase asynchronous motor refers to a single-phase motor without phase shift capacitance, U terminal is connected to the main winding, V terminal is connected to the common end, and W terminal is connected to the auxiliary winding.
675 675  
676 -(% style="width:875px" %)
677 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.01|(% colspan="2" style="text-align:center" %)Rated power of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
678 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.1kW to 400.0kW
679 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.02|(% colspan="2" style="text-align:center" %)Rated voltage of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
680 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)1V to 440V
681 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.03|(% colspan="2" style="text-align:center" %)Rated current of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
682 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.1A to 2000.0A
683 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.04|(% colspan="2" style="text-align:center" %)Rated power of motor|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
684 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)0.00Hz to Maximum frequency F0.10
685 -|(% colspan="2" rowspan="2" style="text-align:center" %)F2.05|(% colspan="2" style="text-align:center" %)Rated motor speed|(% colspan="2" style="text-align:center" %)Factory default|(% colspan="2" style="text-align:center" %)Model determination
686 -|(% colspan="2" style="text-align:center" %)Setting range|(% colspan="4" style="text-align:center" %)1rpm to 65000rpm
687 -|(% colspan="8" %)**✎Note:**(((
690 +| |(% rowspan="2" %)F2.01|(% colspan="2" %)Rated power of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
691 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.1kW to 400.0kW|
692 +| |(% rowspan="2" %)F2.02|(% colspan="2" %)Rated voltage of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
693 +| |(% colspan="2" %)Setting range|(% colspan="4" %)1V to 440V|
694 +| |(% rowspan="2" %)F2.03|(% colspan="2" %)Rated current of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
695 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.1A to 2000.0A|
696 +| |(% rowspan="2" %)F2.04|(% colspan="2" %)Rated power of motor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
697 +| |(% colspan="2" %)Setting range|(% colspan="4" %)0.00Hz-Maximum frequency F0.10|
698 +| |(% rowspan="2" %)F2.05|(% colspan="2" %)Rated motor speed|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination|
699 +| |(% colspan="2" %)Setting range|(% colspan="4" %)1rpm to 65000rpm|
700 +|(% colspan="8" %)**Note:**|
701 +|(% colspan="8" %)(((
688 688  1. Please set according to the nameplate parameters of the motor.
689 689  
690 690  2. The excellent control performance of vector control requires accurate motor parameters, and accurate parameter identification comes from the correct setting of the rated parameters of the motor.
691 691  
692 692  3. In order to ensure the control performance, please configure the motor according to the inverter standard adaptation motor, if the motor power and the standard adaptation motor gap is too large, the control performance of the inverter will be significantly reduced.
693 -)))
694 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.06|(% colspan="2" style="text-align:center; width:493px" %)Motor stator resistance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
695 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.001Ω to 65.000Ω
696 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.07|(% colspan="2" style="text-align:center; width:493px" %)Motor rotor resistance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
697 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.001Ω to 65.000Ω
698 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.08|(% colspan="2" style="text-align:center; width:493px" %)Motor fixed rotor inductance|(% colspan="2" style="text-align:center" %)Factory default|Model determination
699 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 6500.0mH
700 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.09|(% colspan="2" style="text-align:center; width:493px" %)Mutual inductance of motor fixed rotor|(% colspan="2" style="text-align:center" %)Factory default|Model determination
701 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 6500.0mH
702 -|(% colspan="3" rowspan="2" style="text-align:center; width:84px" %)F2.10|(% colspan="2" style="text-align:center; width:493px" %)Motor no-load current|(% colspan="2" style="text-align:center" %)Factory default|Model determination
703 -|(% colspan="2" style="text-align:center; width:493px" %)Setting range|(% colspan="3" style="text-align:center" %)0.1 to 650.0A
707 +)))|
708 +|(% colspan="3" rowspan="2" %)F2.06|(% colspan="2" %)Motor stator resistance|(% colspan="2" %)Factory default|Model determination|
709 +|(% colspan="2" %)Setting range|(% colspan="3" %)0.001Ω to 65.000Ω|
710 +|(% colspan="3" rowspan="2" %)F2.07|(% colspan="2" %)Motor rotor resistance|(% colspan="2" %)Factory default|Model determination|
711 +|(% colspan="2" %)Setting range|(% colspan="3" %)0.001Ω to 65.000Ω|
712 +|(% colspan="3" rowspan="2" %)F2.08|(% colspan="2" %)Motor fixed rotor inductance|(% colspan="2" %)Factory default|Model determination|
713 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 6500.0mH
714 +|(% colspan="3" rowspan="2" %)F2.09|(% colspan="2" %)Mutual inductance of motor fixed rotor|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination
715 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 6500.0mH
716 +|(% colspan="3" rowspan="2" %)F2.10|(% colspan="2" %)Motor no-load current|(% colspan="2" %)Factory default|(% colspan="2" %)Model determination
717 +|(% colspan="2" %)Setting range|(% colspan="4" %)0.1 to 650.0A
704 704  
705 705  After the automatic tuning of the asynchronous motor is completed normally, the set values of the asynchronous motor parameters (F2.06 to F2.10) are automatically updated.
706 706  
707 707  After changing the motor rated power F2.01 each time, the VFD F2.06 to F2.10 parameter values will automatically restore the default standard motor parameters, if running in vector mode, please re-tune.
708 708  
709 -|(% rowspan="2" style="text-align:center; width:135px" %)F2.11|(% style="text-align:center; width:266px" %)Tuning selection|(% style="text-align:center; width:202px" %)Factory default|(% style="text-align:center" %)0
710 -|(% style="text-align:center; width:266px" %)Setting range|(% colspan="2" style="width:231px" %)(((
723 +|(% rowspan="2" %)F2.11|Tuning selection|Factory default|0
724 +|Setting range|(% colspan="2" %)(((
711 711  0: No operation is performed
712 712  
713 713  1: Static tuning 1
... ... @@ -717,6 +717,8 @@
717 717  3: Static tuning 2 (AM calculated Lm)
718 718  )))
719 719  
734 +
735 +
720 720  Tip: Before tuning, you must set the correct motor type and rating parameters (F2.00 to F2.05).
721 721  
722 722  0: No operation is performed, that is, tuning is disabled.
... ... @@ -735,13 +735,15 @@
735 735  
736 736  Note: Tuning can only be effective in keyboard control mode, acceleration and deceleration time is recommended to use the factory default.
737 737  
738 -|(% rowspan="2" style="text-align:center" %)F2.12|(% style="text-align:center" %)G/P Machine type|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
739 -|(% style="text-align:center" %)Setting range|(% colspan="2" %)(((
740 -0: G-type machine;
754 +|(% rowspan="2" %)F2.12|G/P Machine type|Factory default|Model determination
755 +|Setting range|(% colspan="2" %)(((
756 +0: G type machine;
741 741  
742 742  1: P-type machine
743 743  )))
744 744  
761 +
762 +
745 745  This parameter can only be used to view factory models.
746 746  
747 747  1: Constant torque load for specified rated parameters.
... ... @@ -748,63 +748,73 @@
748 748  
749 749  2: Suitable for the specified rated parameters of the variable torque load (fan, pump load).
750 750  
751 -|(% rowspan="2" style="text-align:center" %)F2.13|(% style="text-align:center" %)Single phase asynchronous motor turns ratio|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)100%
752 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)10 to 200%
769 +|(% rowspan="2" %)F2.13|Single phase asynchronous motor turns ratio|Factory default|100%
770 +|Setting range|(% colspan="2" %)10 to 200%
753 753  
772 +
773 +
754 754  U terminal main winding, V terminal auxiliary winding, W common end, this parameter is used to set the ratio of the number of turns between the main winding and the auxiliary winding of the single-phase motor.
755 755  
756 -|(% rowspan="2" style="text-align:center" %)F2.14|(% style="text-align:center" %)Current calibration coefficient of single-phase motor|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)120%
757 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)50 to 200%
776 +|(% rowspan="2" %)F2.14|Current calibration coefficient of single-phase motor|Factory default|120%
777 +|Setting range|(% colspan="2" %)50 to 200%
758 758  
759 759  The single-phase motor has main and auxiliary windings, and the three-phase output current is unbalanced, so the output current displayed by the inverter needs to be multiplied by the coefficient of the resultant current.
760 760  
761 -|(% rowspan="2" style="text-align:center" %)F2.15|(% style="text-align:center; width:310px" %)Number of motor poles|(% style="text-align:center; width:167px" %)Factory default|(% style="text-align:center" %)4
762 -|(% style="text-align:center; width:310px" %)Setting range|(% colspan="2" style="text-align:center; width:215px" %)2 to 48
763 763  
782 +|(% rowspan="2" %)F2.15|Number of motor poles|Factory default|4
783 +|Setting range|(% colspan="2" %)2 to 48
784 +
785 +
786 +
764 764  Change F2.04 or F2.05, the program will automatically calculate the number of motor poles, in general, do not need to set this parameter.
765 765  
766 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.22|(% style="text-align:center; width:242px" %)Stator resistance of synchro|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
767 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.001 to 65.000(0.001Ohm)
768 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.23|(% style="text-align:center; width:242px" %)Synchro d-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
769 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.01mH to 655.35mH
770 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.24|(% style="text-align:center; width:242px" %)Synchro Q-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
771 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.01mH to 655.35mH
772 -|(% rowspan="2" style="text-align:center; width:92px" %)F2.25|(% style="text-align:center; width:242px" %)Synchro back electromotive force|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
773 -|(% style="text-align:center; width:242px" %)Setting range|(% colspan="2" style="text-align:center" %)0.1V to 1000.0V
789 +|(% rowspan="2" %)F2.22|Stator resistance of synchro|Factory default|Model determination
790 +|Setting range|(% colspan="2" %)0.001 to 65.000(0.001Ohm)
791 +|(% rowspan="2" %)F2.23|Synchro d-axis inductance|Factory default|Model determination
792 +|Setting range|(% colspan="2" %)0.01mH-655.35mH
793 +|(% rowspan="2" %)F2.24|Synchro Q-axis inductance|Factory default|Model determination
794 +|Setting range|(% colspan="2" %)0.01mH to 655.35mH
795 +|(% rowspan="2" %)F2.25|Synchro back electromotive force|Factory default|Model determination
796 +|Setting range|(% colspan="2" %)0.1V to 1000.0V
774 774  
775 775  After the automatic tuning of the synchronous motor is completed, the set values of the synchronous motor parameters (F2.22 to F2.25) are automatically updated.
776 776  
777 777  After changing the rated motor power F2.01 each time, the F2.22 to F2.25 parameter values of the inverter will automatically restore the default standard motor parameters, please re-tune.
778 778  
779 -|(% rowspan="2" style="text-align:center" %)F2.28|(% style="text-align:center" %)High frequency injection voltage|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)20.0%
780 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1% to 100.0%
802 +|(% rowspan="2" %)F2.28|High frequency injection voltage|Factory default|20.0%
803 +|Setting range|(% colspan="2" %)0.1% to 100.0%
781 781  
805 +
806 +
782 782  The current injected when the synchronous motor learns the inductance of DQ axis by high frequency injection.
783 783  
784 -|(% rowspan="2" style="text-align:center" %)F2.29|(% style="text-align:center" %)Back potential identification current|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)50.0%
785 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1% to 100.0%
809 +|(% rowspan="2" %)F2.29|Back potential identification current|Factory default|50.0%
810 +|Setting range|(% colspan="2" %)0.1% to 100.0%
786 786  
812 +
813 +
787 787  The output current of the inverter is the size when the synchronous motor dynamically adjusts to learn the back potential.
788 788  
789 -|(% rowspan="2" style="text-align:center" %)F2.31|(% style="text-align:center" %)Asynchronous no-load current per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
790 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1%
791 -|(% rowspan="2" style="text-align:center" %)F2.32|(% style="text-align:center" %)Per unit asynchronous stator resistance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
792 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
793 -|(% rowspan="2" style="text-align:center" %)F2.33|(% style="text-align:center" %)Asynchronous rotor resistance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
794 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
795 -|(% rowspan="2" style="text-align:center" %)F2.34|(% style="text-align:center" %)Asynchronous mutual inductance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
796 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1%
797 -|(% rowspan="2" style="text-align:center" %)F2.35|(% style="text-align:center" %)Asynchronous leakage sensing per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
798 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
799 -|(% rowspan="2" style="text-align:center" %)F2.36|(% style="text-align:center" %)Per unit value of asynchronous leakage sensing coefficient|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
800 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
801 -|(% rowspan="2" style="text-align:center" %)F2.37|(% style="text-align:center" %)Synchronous stator resistance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
802 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
803 -|(% rowspan="2" style="text-align:center" %)F2.38|(% style="text-align:center" %)Per unit value of synchronous D-axis inductance|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
804 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
805 -|(% rowspan="2" style="text-align:center" %)F2.39|(% style="text-align:center" %)Synchronous Q-axis inductance per unit value|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
806 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.01%
807 -|(% rowspan="2" style="text-align:center" %)F2.40|(% style="text-align:center" %)Back electromotive force of synchronous motor|(% style="text-align:center" %)Factory default|(% style="text-align:center" %)Model determination
808 -|(% style="text-align:center" %)Setting range|(% colspan="2" style="text-align:center" %)0.1V
809 809  
810 -The per unit value of the motor parameters is used for the actual program calculation. After learning or parameter recovery, the actual change is F2.31 to F2.40. F2.06 to F2.10 and F2.22 to F2.25 are calculated from the per unit value, so only F2.31 to F2.40 values can be modified, F2.06 to F2.10 and F2.22 to F2.25 are only used to display and cannot be changed.
817 +|(% rowspan="2" %)F2.31|Asynchronous no-load current per unit value|Factory default|Model determination
818 +|Setting range|(% colspan="2" %)0.1%
819 +|(% rowspan="2" %)F2.32|Per unit asynchronous stator resistance|Factory default|Model determination
820 +|Setting range|(% colspan="2" %)0.01%
821 +|(% rowspan="2" %)F2.33|Asynchronous rotor resistance per unit value|Factory default|Model determination
822 +|Setting range|(% colspan="2" %)0.01%
823 +|(% rowspan="2" %)F2.34|Asynchronous mutual inductance per unit value|Factory default|Model determination
824 +|Setting range|(% colspan="2" %)0.1%
825 +|(% rowspan="2" %)F2.35|Asynchronous leakage sensing per unit value|Factory default|Model determination
826 +|Setting range|(% colspan="2" %)0.01%
827 +|(% rowspan="2" %)F2.36|Per unit value of asynchronous leakage sensing coefficient|Factory default|Model determination
828 +|Setting range|(% colspan="2" %)0.01%
829 +|(% rowspan="2" %)F2.37|Synchronous stator resistance per unit value|Factory default|Model determination
830 +|Setting range|(% colspan="2" %)0.01%
831 +|(% rowspan="2" %)F2.38|Per unit value of synchronous D-axis inductance|Factory default|Model determination
832 +|Setting range|(% colspan="2" %)0.01%
833 +|(% rowspan="2" %)F2.39|Synchronous Q-axis inductance per unit value|Factory default|Model determination
834 +|Setting range|(% colspan="2" %)0.01%
835 +|(% rowspan="2" %)F2.40|Back electromotive force of synchronous motor|Factory default|Model determination
836 +|Setting range|(% colspan="2" %)0.1V
837 +
838 +The per unit value of the motor parameters is used for the actual program calculation. After learning or parameter recovery, the actual change is F2.31-F2.40. F2.06-F2.10 and F2.22-F2.25 are calculated from the per unit value, so only F2.31-F2.40 values can be modified, F2.06-F2.10 and F2.22-F2.25 are only used to display and cannot be changed.
1763024398600-482.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Iris
Size
... ... @@ -1,1 +1,0 @@
1 -99.1 KB
Content