| ... |
... |
@@ -85,7 +85,8 @@ |
| 85 |
85 |
|
| 86 |
86 |
== Use of blade terminals == |
| 87 |
87 |
|
| 88 |
|
-[[image:image-20220705162505-2.jpeg]] |
|
88 |
+(% style="text-align:center" %) |
|
89 |
+[[image:image-20220622145005-4.jpeg||height="220" width="366"]] |
| 89 |
89 |
|
| 90 |
90 |
Use crimp terminals of the size shown in the figure. Terminal tightening torque is 0.5 to 0.8N.m. Be sure to tighten the screws so as not to cause malfunction. |
| 91 |
91 |
|
| ... |
... |
@@ -114,7 +114,7 @@ |
| 114 |
114 |
= **4 Wiring ** = |
| 115 |
115 |
|
| 116 |
116 |
(% style="text-align:center" %) |
| 117 |
|
-[[image:image-20220705162452-1.jpeg]] |
|
118 |
+[[image:image-20220622145005-5.jpeg||height="522" width="706"]] |
| 118 |
118 |
|
| 119 |
119 |
**✎Note:** |
| 120 |
120 |
|
| ... |
... |
@@ -502,18 +502,18 @@ |
| 502 |
502 |
|
| 503 |
503 |
* Calibration with weights |
| 504 |
504 |
** Step1: Do not put any weights on the load cell. |
| 505 |
|
-** Step2: Write 0x0001 to #8. |
|
506 |
+** Step2: #8 value is written as 0x0001. |
| 506 |
506 |
** Step3: Add standard weights to the load cell. |
| 507 |
507 |
** Step4: Write the weight of the current weight on the chassis into #23. |
| 508 |
|
-** Step5: Write 0x0002 to #8. |
|
509 |
+** Step5: #8 value is written as 0x0002. |
| 509 |
509 |
* Weightless calibration |
| 510 |
510 |
** Step1: Do not put any weights on the load cell. |
| 511 |
511 |
** Step2: Write the maximum range of the sensor into #23. |
| 512 |
512 |
** Step3: Write the sensor sensitivity into #39, accurate to three decimal places. |
| 513 |
|
-** Step4: Write 0x0003 to #8. |
|
514 |
+** Step4: #8 value is written as 0x0003. |
| 514 |
514 |
* Modify calibration parameters: |
| 515 |
515 |
** Step1: Modify the calibration parameter values in BFM#35 to BFM#38; |
| 516 |
|
-** Step2: Write 0x0004 to #8. |
|
517 |
+** Step2: #8 value is written as 0x0004. |
| 517 |
517 |
|
| 518 |
518 |
**✎Note: **When a value is written to BFM#8 or BFM#48 using the device monitor, it is automatically reset to 0. |
| 519 |
519 |
|
| ... |
... |
@@ -533,7 +533,7 @@ |
| 533 |
533 |
|
| 534 |
534 |
|**Settings**|(% style="width:599px" %)**Description**|(% style="width:404px" %)**Remark** |
| 535 |
535 |
|0|(% style="width:599px" %)Do not enable zero tracking|(% style="width:404px" %)Default |
| 536 |
|
-|1 to 300|(% style="width:599px" %)When setting the zero tracking range (absolute value), tracking must be performed when the value is stable and the current weight is within the zero tracking range.|(% style="width:404px" %)((( |
|
537 |
+|1 to 100|(% style="width:599px" %)When setting the zero tracking range (absolute value), tracking must be performed when the value is stable and the current weight is within the zero tracking range.|(% style="width:404px" %)((( |
| 537 |
537 |
If set to 10, the current weight is ±9 and the stable flag is 1, the current weight is cleared. |
| 538 |
538 |
))) |
| 539 |
539 |
|(% colspan="3" %)**✎Note: **When the accuracy of the measured items is not high, the temperature drift has little effect, and this function is not required. |
