| ... |
... |
@@ -83,9 +83,10 @@ |
| 83 |
83 |
|(% rowspan="2" style="width:121px" %)WE light|(% rowspan="2" style="width:346px" %)Calibration indicator for the channel|(% style="width:126px" %)Lights off|(% style="width:483px" %)Calibration succeeded |
| 84 |
84 |
|(% style="width:126px" %)Always ON|(% style="width:483px" %)Calibration failed or not calibrated |
| 85 |
85 |
|
| 86 |
|
-== Use of blade terminals == |
|
86 |
+== **Use of blade terminals** == |
| 87 |
87 |
|
| 88 |
|
-[[image:image-20220705162505-2.jpeg]] |
|
88 |
+(% style="text-align:center" %) |
|
89 |
+[[image:image-20220705162505-2.jpeg||height="218" width="375"]] |
| 89 |
89 |
|
| 90 |
90 |
Use crimp terminals of the size shown in the figure. Terminal tightening torque is 0.5 to 0.8N.m. Be sure to tighten the screws so as not to cause malfunction. |
| 91 |
91 |
|
| ... |
... |
@@ -617,12 +617,12 @@ |
| 617 |
617 |
The adjustment is to make the module match the weight value of the load cell of the weighing module. The adjustment steps are as follows. Described with CH1. |
| 618 |
618 |
|
| 619 |
619 |
(% style="text-align:center" %) |
| 620 |
|
-[[image:image-20220622145005-8.jpeg||height="193" width="797"]] |
|
621 |
+[[image:image-20220705162540-3.jpeg]] |
| 621 |
621 |
|
| 622 |
622 |
**Tare weight and gross weight** |
| 623 |
623 |
|
| 624 |
624 |
(% style="text-align:center" %) |
| 625 |
|
-[[image:image-20220622145005-9.jpeg||height="274" width="749"]] |
|
626 |
+[[image:image-20220705162551-4.jpeg]] |
| 626 |
626 |
|
| 627 |
627 |
**Filter mode setting** |
| 628 |
628 |
|
| ... |
... |
@@ -629,7 +629,7 @@ |
| 629 |
629 |
After setting the filtering mode and filtering strength, you need to calibrate it again. |
| 630 |
630 |
|
| 631 |
631 |
(% style="text-align:center" %) |
| 632 |
|
-[[image:image-20220622145005-10.jpeg||height="196" width="791"]] |
|
633 |
+[[image:image-20220705162602-5.jpeg]] |
| 633 |
633 |
|
| 634 |
634 |
**Zero tracking** |
| 635 |
635 |
|
| ... |
... |
@@ -638,7 +638,7 @@ |
| 638 |
638 |
Set Zero Tracking Intensity to 0 to disable tracking. Set Zero Tracking Range to 0 to make it is unlimited. |
| 639 |
639 |
|
| 640 |
640 |
(% style="text-align:center" %) |
| 641 |
|
-[[image:image-20220622145005-11.jpeg||height="242" width="601"]] |
|
642 |
+[[image:image-20220705162610-6.jpeg]] |
| 642 |
642 |
|
| 643 |
643 |
**Calibration without weights** |
| 644 |
644 |
|
| ... |
... |
@@ -647,12 +647,12 @@ |
| 647 |
647 |
Example: The sensitivity of LAB-B-B sensor is 2.0±10%mV/V, and there may be a maximum error of 10%, so it is best to use a sensor with a small sensor sensitivity error to use this function. |
| 648 |
648 |
|
| 649 |
649 |
(% style="text-align:center" %) |
| 650 |
|
-[[image:image-20220622145005-12.jpeg||height="323" width="774"]] |
|
651 |
+[[image:image-20220705162619-7.jpeg]] |
| 651 |
651 |
|
| 652 |
652 |
**Modify calibration parameters** |
| 653 |
653 |
|
| 654 |
654 |
(% style="text-align:center" %) |
| 655 |
|
-[[image:image-20220622145005-13.jpeg||height="315" width="838"]] |
|
656 |
+[[image:image-20220705162627-8.jpeg]] |
| 656 |
656 |
|
| 657 |
657 |
**✎Note: **BFM35, BFM36, BFM37, and BFM38 are real number (float). Real numbers need to be input when inputting. If the input exceeds the range, BFM5 will report an error in writing calibration parameters. |
| 658 |
658 |
|
