Changes for page 06 Data Tool

Last modified by Jett on 2025/02/18 16:43

From 1.1 to 2.1 From 3.6 to 4.1

From version 2.1

edited by Joey
on 2022/06/16 13:58

Change comment: There is no comment for this version

To version 3.6

edited by Stone Wu
on 2022/06/30 11:43

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (2 modified, 0 added, 0 removed)
Attachments (0 modified, 1 added, 0 removed)
- image-20220616145435-1.png

Details

Page properties

Author

@@ -1,1 +1,1 @@
--XWiki.Joey
++XWiki.Stone

Content

@@ -1,9 +1,9 @@
  (% class="wikigeneratedid" id="H8BasicFunction" %)
--This chapter provides information about basic functions and configiration in PIStudio.
++This chapter provides information about basic functions and configuration in PIStudio.
  = **{{id name="_Toc28532"/}}Alarm** =
--== **Bit Alarm** ==
++== **Bit alarm** ==
  Click "Project"->"Bit alarm", it is displayed as the following figure.
@@ -18,7 +18,7 @@
 . **Record bit alarm by default:**  Whether to record the alarm history data of bit alarm, if checked, it will be saved in the designated storage location.
 . **Not save alarm OFF:** If checked, after the alarm is dismissed, the corresponding alarm records will be deleted from the log file.
--**(3) Upload to Cloud: **The data upload by "bit alarm" is stored in the Cloud aand it is alarm data. (Only ig supported)
++**(3) Upload to Cloud: **The data upload by "bit alarm" is stored in the Cloud and it is alarm data. (Only ig supported)
  **(4) Alarm Condition:** It sets alarm trigger condition, there are two types: alarm when ON and alarm when OFF.
@@ -37,7 +37,7 @@
  **✎Note:**
--* If the "cloud" function is enabled and "upload to cloud" is checked, the communnication port of the address in the configuration of the imported bit alarm record must be the same as that of the current project; otherwise, it cannot be used normally.
++* If the "cloud" function is enabled and "upload to cloud" is checked, the communication port of the address in the configuration of the imported bit alarm record must be the same as that of the current project; otherwise, it cannot be used normally.
  * The number of alarm configuration points reported to the cloud cannot exceed 20, or the sum of imported alarm records and the current alarm records cannot exceed 20. If it exceeds, please reconfigure.
  **Operating Procedures of Adding One Alarm**
@@ -64,7 +64,7 @@
  Word alarm is to monitor the word address of a device. If the data meets the set conditions, an alarm will be generated.
--Click "Porject"->"Word alarm", it is displayed as the following figure.
++Click "Project"->"Word alarm", it is displayed as the following figure.
  (% style="text-align:center" %)
  [[image:字报警 1.png||class="img-thumbnail"]]
@@ -77,11 +77,11 @@
  **(4)  Group No.: **Group number of word alarm. The name is unique and cannot be duplicated.
--**(5) Upload to Cloud: **The data upload by "word alarm" is stored in the Cloud aand it is alarm data. (Only ig supported)
++**(5) Upload to Cloud: **The data upload by "word alarm" is stored in the Cloud and it is alarm data. (Only ig supported)
  **✎Note:**
--* If the "cloud" function is enabled and "upload to cloud" is checked, the communnication port of the address in the configuration of the imported word alarm record must be the same as that of the current project; otherwise, it cannot be used normally.
++* If the "cloud" function is enabled and "upload to cloud" is checked, the communication port of the address in the configuration of the imported word alarm record must be the same as that of the current project; otherwise, it cannot be used normally.
  * The number of alarm configuration points reported to the cloud cannot exceed 20, or the sum of imported alarm records and the current alarm records cannot exceed 20. If it exceeds, please reconfigure.
  **(6) Record alarm:**  Whether to record the alarm history data of word alarm, if checked, it will be saved in the designated storage location.
@@ -150,7 +150,7 @@
  The maximum number of group in recipe is 1000, and the maximum number of member in each group is 1500.
--Recipe could store the data in USB flash disk and SD card and view the recipe data by obejct "Recipe display". It has two mode: simple mode and advanced mode.
++Recipe could store the data in USB flash disk and SD card and view the recipe data by object "Recipe display". It has two mode: simple mode and advanced mode.
 . **Simple: **Only support the data operation of one recipe file, including read and write.
 . **Advanced:** Support the data operation of multiple recipe files, including read, write, insert and index. View and select recipe file by object "File list".
@@ -273,9 +273,9 @@
  == **Recipe display** ==
--Select the file type "Traditional recipe file" in onject "Recipe Display", and it is recommended to fill in the traditional recipe group number HSW1612 to the address of select line.
++Select the file type "Traditional recipe file" in object "Recipe Display", and it is recommended to fill in the traditional recipe group number HSW1612 to the address of select line.
--**✎Note**: The Recipe Display can display up to 50 groups of 100 elements, which can be to display out of range by enabled "Address Control", as follwoing shown:
++**✎Note**: The Recipe Display can display up to 50 groups of 100 elements, which can be to display out of range by enabled "Address Control", as following shown:
  (% style="text-align:center" %)
  [[image:8-4TraditionalRecipeDisplayConfigScreen.png||class="img-thumbnail"]]
@@ -366,7 +366,7 @@
  **(1) Basic settings**
--1. **Curve NO.: **It is for setting curvenumber,
++1. **Curve NO.: **It is for setting curve number,
 . **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.
 . **Curve (1~~8):** It is for setting the number of curves. The default is 3.
 . **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.
@@ -373,7 +373,7 @@
  **(2) Sample Type**
--1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to adit.
++1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.
 . **Sample unit:** 100ms.
  **(3) Quick Setting**
@@ -384,7 +384,7 @@
  [[image:趋势图设置 3.png||class="img-thumbnail"]]
  (% start="2" %)
--1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
++1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
  **(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.
@@ -408,7 +408,7 @@
  **(1) Basic settings**
--1. **Curve NO.: **It is for setting curvenumber,
++1. **Curve NO.: **It is for setting curve number,
 . **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.
 . **Curve (1~~8):** It is for setting the number of curves. The default is 3.
 . **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.
@@ -415,7 +415,7 @@
  **(2) Sample Type**
--1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to adit.
++1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.
 . **Sample unit:** 100ms.
  **(3) Quick Setting**
@@ -423,10 +423,10 @@
 . **Data format: **It is for setting all the curves, select the data format for all curves, and setting the reading addresses for curves. There are as follows.
  (% style="text-align:center" %)
--[[image:http://docs.we-con.com.cn/wiki/pistudio/download/Helps/08.Basic%20Function/WebHome/%E8%B6%8B%E5%8A%BF%E5%9B%BE%E8%AE%BE%E7%BD%AE%203.png?rev=1.1||alt="趋势图设置 3.png" class="img-thumbnail"]]
++[[image:image-20220616145435-1.png]]
  (% start="2" %)
--1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
++1. **Sample address: **Fill in the start address that read the device data. If the sample address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
  **(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.
@@ -463,7 +463,7 @@
  The data record stored in SD card is also organized according to the above figure.
--The sample time and save time is consistent in the same recored group. There are multiple channels in the group, When the sampling time is up, every channel would collect data to PLC register according to its own address.
++The sample time and save time is consistent in the same record group. There are multiple channels in the group, When the sampling time is up, every channel would collect data to PLC register according to its own address.
  **Sampling interval: **The interval between two consecutive samples was recorded.
@@ -511,7 +511,7 @@
 . **Trigger to record by sample cycle: **Data will be recorded in every same time, when trigger control bit set ON.
 . **Trigger to record once and reset: **Data will be recorded when trigger control bit set ON, and the bit will be reset automatically.
 . **Trigger to record once: **Data will be recorded when trigger control bit set ON, and the bit need to be reset manually.
--1. **Trigger address: **It is only valid when the trigger condition is selected. The monitoring cyclce for trigger sampling address is 1s.
++1. **Trigger address: **It is only valid when the trigger condition is selected. The monitoring cycle for trigger sampling address is 1s.
  **(3) Total channels (1~~100): **Set the numbers of channels. Click "apply" to view the channel lists on the right record channel.
@@ -527,8 +527,8 @@
  **(7) Quick Settings**
--1. **Start Channel:** It sets the continuous addressesfor channels.
--1. **Data Format: **It setsthe samedata format for channels.
++1. **Start Channel:** It sets the continuous addresses for channels.
++1. **Data Format: **It sets the same data format for channels.
 . **Number of Digits:** It sets the digits’ number for channels.
 . **Language Settings**: The text in HMI can be in 8 languages, user can set language in here.
@@ -570,7 +570,7 @@
  [[image:用户权限 1.png||class="img-thumbnail"]]
 . Click "User Permission" in "Data Tool" toolbar.
--1. Edit user name, click "User0" cellunder "UserName", and then enter the user name, one project allows maximum 20 users.
++1. Edit user name, click "User0" cell under "UserName", and then enter the user name, one project allows maximum 20 users.
 . Edit password, click "User0" cell under "PassWord", and then enter the user name.
 . Edit description, click "User0" cell under "Desc", and then enter, description is not necessary。
 . Check the groups for each user, there are 11 groups beside admin.
@@ -597,7 +597,7 @@
 . Enter [Log Message], it is for operation records, if it was empty, the operation for this object would be not be recorded;
 . Select the ~[[[Access Denied Setting>>path:#_Security]]] mode;
--**Log imformation description**
++**Log information description**
 . A combination of Chinese characters, numbers, and uppercase and lowercase letters can be entered, and the number does not exceed 63.
 . The format of insert variable:{variable address, data format}. e.g., {HDW100,UW2.1}.
@@ -762,7 +762,7 @@
  **For Example:**
--Trigger address is 011, during insertinga USB flash disk into HMI, and 011 would be set ON, once HMI recognizes USB flash disk, and display message.
++Trigger address is 011, during inserting a USB flash disk into HMI, and 011 would be set ON, once HMI recognizes USB flash disk, and display message.
 . **Show message: **Check it to display message when HMI is running. It is checked by default.
 . **Show on web: **Check it to display message when remote access HMI screen, it is unchecked by default.
@@ -781,7 +781,7 @@
  * If you do not want this prompt during the running of HMI, please uncheck "Show message".
  * "Reload text" function would be invalid after clicking "save".
--* These 5 special characters are not supported in the header Multilanguage settings: ",", "|", "<", ">", "&".
++* These 5 special characters are not supported in the header Multi language settings: ",", "|", "<", ">", "&".
  = **Cloud (Only ig series)** =

image-20220616145435-1.png

Author

...	...	@@ -1,0 +1,1 @@
	1	+XWiki.Joey

Size

...	...	@@ -1,0 +1,1 @@
	1	+3.6 KB

Content

Changes for page 06 Data Tool

Summary

Details

Navigation

Table of Contents