Changes for page 06 Data Tool

Last modified by Jett on 2025/02/18 16:43

From 3.3 to 3.2 From 4.1 to 3.6

From version 3.6

edited by Stone Wu
on 2022/06/30 11:43

Change comment: There is no comment for this version

To version 3.3

edited by Stone Wu
on 2022/06/30 11:33

Change comment: There is no comment for this version

Raw
Rendered

Summary

Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

@@ -366,7 +366,7 @@
  **(1) Basic settings**
--1. **Curve NO.: **It is for setting curve number,
++1. **Curve NO.: **It is for setting curvenumber,
 . **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.
 . **Curve (1~~8):** It is for setting the number of curves. The default is 3.
 . **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.
@@ -373,7 +373,7 @@
  **(2) Sample Type**
--1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.
++1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to adit.
 . **Sample unit:** 100ms.
  **(3) Quick Setting**
@@ -384,7 +384,7 @@
  [[image:趋势图设置 3.png||class="img-thumbnail"]]
  (% start="2" %)
--1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
++1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
  **(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.
@@ -408,7 +408,7 @@
  **(1) Basic settings**
--1. **Curve NO.: **It is for setting curve number,
++1. **Curve NO.: **It is for setting curvenumber,
 . **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.
 . **Curve (1~~8):** It is for setting the number of curves. The default is 3.
 . **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.
@@ -415,7 +415,7 @@
  **(2) Sample Type**
--1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.
++1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to adit.
 . **Sample unit:** 100ms.
  **(3) Quick Setting**
@@ -426,7 +426,7 @@
  [[image:image-20220616145435-1.png]]
  (% start="2" %)
--1. **Sample address: **Fill in the start address that read the device data. If the sample address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
++1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.
  **(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.
@@ -463,7 +463,7 @@
  The data record stored in SD card is also organized according to the above figure.
--The sample time and save time is consistent in the same record group. There are multiple channels in the group, When the sampling time is up, every channel would collect data to PLC register according to its own address.
++The sample time and save time is consistent in the same recored group. There are multiple channels in the group, When the sampling time is up, every channel would collect data to PLC register according to its own address.
  **Sampling interval: **The interval between two consecutive samples was recorded.
@@ -511,7 +511,7 @@
 . **Trigger to record by sample cycle: **Data will be recorded in every same time, when trigger control bit set ON.
 . **Trigger to record once and reset: **Data will be recorded when trigger control bit set ON, and the bit will be reset automatically.
 . **Trigger to record once: **Data will be recorded when trigger control bit set ON, and the bit need to be reset manually.
--1. **Trigger address: **It is only valid when the trigger condition is selected. The monitoring cycle for trigger sampling address is 1s.
++1. **Trigger address: **It is only valid when the trigger condition is selected. The monitoring cyclce for trigger sampling address is 1s.
  **(3) Total channels (1~~100): **Set the numbers of channels. Click "apply" to view the channel lists on the right record channel.
@@ -527,8 +527,8 @@
  **(7) Quick Settings**
--1. **Start Channel:** It sets the continuous addresses for channels.
--1. **Data Format: **It sets the same data format for channels.
++1. **Start Channel:** It sets the continuous addressesfor channels.
++1. **Data Format: **It setsthe samedata format for channels.
 . **Number of Digits:** It sets the digits’ number for channels.
 . **Language Settings**: The text in HMI can be in 8 languages, user can set language in here.
@@ -570,7 +570,7 @@
  [[image:用户权限 1.png||class="img-thumbnail"]]
 . Click "User Permission" in "Data Tool" toolbar.
--1. Edit user name, click "User0" cell under "UserName", and then enter the user name, one project allows maximum 20 users.
++1. Edit user name, click "User0" cellunder "UserName", and then enter the user name, one project allows maximum 20 users.
 . Edit password, click "User0" cell under "PassWord", and then enter the user name.
 . Edit description, click "User0" cell under "Desc", and then enter, description is not necessary。
 . Check the groups for each user, there are 11 groups beside admin.
@@ -597,7 +597,7 @@
 . Enter [Log Message], it is for operation records, if it was empty, the operation for this object would be not be recorded;
 . Select the ~[[[Access Denied Setting>>path:#_Security]]] mode;
--**Log information description**
++**Log imformation description**
 . A combination of Chinese characters, numbers, and uppercase and lowercase letters can be entered, and the number does not exceed 63.
 . The format of insert variable:{variable address, data format}. e.g., {HDW100,UW2.1}.
@@ -762,7 +762,7 @@
  **For Example:**
--Trigger address is 011, during inserting a USB flash disk into HMI, and 011 would be set ON, once HMI recognizes USB flash disk, and display message.
++Trigger address is 011, during insertinga USB flash disk into HMI, and 011 would be set ON, once HMI recognizes USB flash disk, and display message.
 . **Show message: **Check it to display message when HMI is running. It is checked by default.
 . **Show on web: **Check it to display message when remote access HMI screen, it is unchecked by default.
@@ -781,7 +781,7 @@
  * If you do not want this prompt during the running of HMI, please uncheck "Show message".
  * "Reload text" function would be invalid after clicking "save".
--* These 5 special characters are not supported in the header Multi language settings: ",", "|", "<", ">", "&".
++* These 5 special characters are not supported in the header Multilanguage settings: ",", "|", "<", ">", "&".
  = **Cloud (Only ig series)** =

Changes for page 06 Data Tool

Summary

Details

Navigation

Table of Contents