Skip to Content

Changes for page 06 Data Tool

Last modified by Jett on 2025/02/18 16:43
From version 32.1
edited by Jim
on 2023/08/11 09:33
Change comment: There is no comment for this version
To version 24.7
edited by Stone Wu
on 2022/08/06 10:26
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Jim
1 +XWiki.Stone
Content
... ... @@ -19,20 +19,17 @@
19 19  
20 20  **Upload to Cloud: **The data upload by "bit alarm" is stored in the Cloud and it is alarm data. (Only ig series and 8000/9000 series with -R after system upgrade are supported)
21 21  
22 -(% class="box infomessage" %)
23 -(((
24 24  **✎Note:**
25 25  
26 26  * After enable the Cloud and check the box of Upload to Cloud, the communication port settings of the address in the imported Bit Alarm record configuration must be the same as the communication port settings of the current project, otherwise it cannot be used normally.
27 27  * The number of Alarm records upload to Cloud shall not exceed the limit value, or the sum of the imported alarm records and the number of existing alarm records shall not exceed the limit value. the specific limitation as following table:
28 28  
29 -(% class="table-bordered" style="margin-left:auto; margin-right:auto; width:358px" %)
27 +(% style="margin-left:auto; margin-right:auto; width:358px" %)
30 30  |=(% style="width: 79px;" %)Series|=(% style="width: 276px;" %)Number of Alarm upload to Cloud
31 31  |(% style="width:79px" %)8000-R|(% style="text-align:center; width:276px" %)200
32 32  |(% style="width:79px" %)9000-R|(% style="text-align:center; width:276px" %)200
33 33  |(% style="width:79px" %)3000ig|(% style="text-align:center; width:276px" %)20
34 34  |(% style="width:79px" %)8000ig|(% style="text-align:center; width:276px" %)200
35 -)))
36 36  
37 37  **Alarm Condition:** It sets alarm trigger condition, there are two types: alarm when ON and alarm when OFF.
38 38  
... ... @@ -91,8 +91,6 @@
91 91  
92 92  **Upload to Cloud: **The data upload by "word alarm" is stored in the Cloud and it is alarm data. (Only ig series and 8000/9000 series with -R after system upgrade are supported)
93 93  
94 -(% class="box infomessage" %)
95 -(((
96 96  **✎Note:**
97 97  
98 98  * If the "cloud" function is enabled and "upload to cloud" is checked, the communication port of the address in the configuration of the imported word alarm record must be the same as that of the current project; otherwise, it cannot be used normally.
... ... @@ -104,7 +104,6 @@
104 104  |(% style="width:79px" %)9000-R|(% style="text-align:center; width:276px" %)200
105 105  |(% style="width:79px" %)3000ig|(% style="text-align:center; width:276px" %)20
106 106  |(% style="width:79px" %)8000ig|(% style="text-align:center; width:276px" %)200
107 -)))
108 108  
109 109  **Record alarm:**  Whether to record the alarm history data of word alarm, if checked, it will be saved in the designated storage location.
110 110  
... ... @@ -247,29 +247,13 @@
247 247  **✎Note: **This function only supported in HMI+, i series, ie series, ig series.
248 248  )))
249 249  
244 +[[image:image-20220805174501-1.jpeg]]
250 250  
251 -**description of Adcanced mode**
246 +[[image:image-20220805174543-2.jpeg]]
252 252  
253 -According to the recipe configuration information in Figure 2 above. The function address is HDW70, and each function configuration corresponds to the group number address, recipe element address and recipe file name address. The recipe information configured in figure 2 can be displayed in the table in figure 3 with the "Record Display" object.
254 -
255 -[[image:image-20220806111333-1.jpeg]]
256 -
257 -**Read recipe**: Input 1 to the file name, when the group number addresses HDW100=1 and HDW70=1 (read), the element data of the first group (ID=1) is written to the recipe address from the recipe file. As shown in Figure 3 above: HDW105=1, HHDW106=2, HDW107=3, HDW108=4, HDW109=5.
258 -
259 -**Write recipe**: Input 1 to the file name, when the group number addresses HDW101=4 and HDW70=2 (write), the data will be read from the recipe address and written to the corresponding group of the recipe file. As shown in figure 3 above: HDW110=20, HHDW111=21, HDW112=22, HDW113=23, HDW114=24. Write the data of this set to the elements of ID=4 in the recipe table (if there is no data of Group 4 in the recipe file, a new set of data will be added; If there is data of Group 4 in the original recipe, the original data will be overwritten and the latest data will be displayed in the recipe file).
260 -
261 -**Index recipe**: When the file name is input 1, when the group number address HDW102=3, the data of ID=3 (Group 3) in the recipe file will be directly displayed in the component address of the index, that is, HDW115=11, HHDW116=12, HDW117=13, HDW118=14 and HDW119=15. If the data of the index component address is modified, the modified data will be automatically filled into the table of the recipe file, that is, the data of the recipe file will be automatically updated after the data is modified.
262 -
263 -[[image:image-20220806111355-2.jpeg]]
264 -
265 -**Insert recipe**: Input 1 to the file name, when the group number addresses HDW103=3 and HDW70=4 (insert), the data of the 3rd group will be inserted, but the data of the third group already exists in the original recipe file (see Figure 3 above), then the original data will be moved down by one group, that is, the original 3rd group will become the 4th group, and so on, and HDW120=16, HHDW121=17, HDW122=18, HDW123=19 and HDW124=20 will be written into the new 3rd group of the recipe file at the same time. The results are shown in Figure 4 above.
266 -
267 -When the group number address HDW101=2 (**The delete function only works on the group number of the write function**), HDW70=8 (delete), the data in the recipe file with ID=2 (Group 2) will be deleted.
268 -
269 -When the group number address HDW101=5 (**The delete function only works on the group number of the write function**), HDW70=16 (delete and sort), the data of ID=5 (Group 5) in the recipe file will be deleted, and the original ID=6 (Group 6) data will be reordered to become the new Group 5 data, the original ID=7 (Group 7) data will be reordered to become the new Group 6 data, and so on.
270 -
271 271  **Recipe Demo Download Link: **[[Download>>url:https://drive.google.com/open?id=1Cjbq_tW-NIirHFBpxt47g7IKvoYaWqUR]]
272 272  
250 +
273 273  == Calling CSV recipe file ==
274 274  
275 275  **Overview**
... ... @@ -695,10 +695,7 @@
695 695  
696 696  (% class="box infomessage" %)
697 697  (((
698 -✎**Note: **
699 -
700 -* The user name and password must be unique.
701 -* The multi language function of User permission only supported on HMI system version V2.0 or above
676 +✎**Note: **The user name and password must be unique.
702 702  )))
703 703  
704 704  == Settings ==
... ... @@ -708,11 +708,6 @@
708 708  (% style="text-align:center" %)
709 709  [[image:用户权限 1.png||class="img-thumbnail"]]
710 710  
711 -Click on the cell from UserName and Desc, which can support the multi language.
712 -
713 -(% style="text-align:center" %)
714 -[[image:UserPermissionMultilan.png]]
715 -
716 716  1. Click "User Permission" in "Data Tool" toolbar.
717 717  1. Edit user name, click "User0" cell under "UserName", and then enter the user name, one project allows maximum 20 users.
718 718  1. Edit password, click "User0" cell under "PassWord", and then enter the user name.
... ... @@ -726,9 +726,6 @@
726 726  * Only a maximum of one administrator permission is allowed in a profile with one user permission. If you want to use "Funtion address" to modify the user permission, you must log in the administrator account to operate.
727 727  * When the configured file does not have the administrator account, a new user can be added  through "Funtion address" and set as the administrator.
728 728  * If you select hidden fucntion when configuring user account, the account would display as "~*~*~*~*~*~*" in the list. You only need to enter the password of the corresponding hidden user to log in.
729 -* (((
730 -Adding new UserName and Desc on the HMI by special addresses in the current language of the HMI, other languages will also configure the user names and user descriptions to the current language by default, i.e. switching to other languages, the new user names and user descriptions will not change with the language.
731 -)))
732 732  
733 733  == Object permission configuration ==
734 734  
... ... @@ -735,11 +735,6 @@
735 735  (% style="text-align:center" %)
736 736  [[image:用户权限 2.png||class="img-thumbnail"]]
737 737  
738 -User operation logs support multi languages configuration. Click on the Log Message, the text editor of multi language will be pop up:
739 -
740 -(% style="text-align:center" %)
741 -[[image:LogMessagesMultilan.png]]
742 -
743 743  **Operation Procedure of Object Permission**
744 744  
745 745  1. Open the object setting windows;
LogMessagesMultilan.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -37.5 KB
Content
UserPermissionMultilan.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Hunter
Size
... ... @@ -1,1 +1,0 @@
1 -23.2 KB
Content
image-20220806111333-1.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Stone
Size
... ... @@ -1,1 +1,0 @@
1 -131.4 KB
Content
image-20220806111355-2.jpeg
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Stone
Size
... ... @@ -1,1 +1,0 @@
1 -135.4 KB
Content