06 Data Tool

* **Record bit alarm by default:** Whether to record the alarm history data of bit alarm, if checked, it will be saved in the designated storage location.

18

* **Not save alarm OFF:** If checked, after the alarm is dismissed, the corresponding alarm records will be deleted from the log file.

19

20

**Upload to Cloud: **The data upload by "bit alarm" is stored in the Cloud and it is alarm data. (Only ig series and 8000/9000 series with -R after system upgrade are supported)

21

22

(% class="box infomessage" %)

(((

**✎Note:**

* After enable the Cloud and check the box of Upload to Cloud, the communication port settings of the address in the imported Bit Alarm record configuration must be the same as the communication port settings of the current project, otherwise it cannot be used normally.

27

* The number of Alarm records upload to Cloud shall not exceed the limit value, or the sum of the imported alarm records and the number of existing alarm records shall not exceed the limit value. the specific limitation as following table:

28

29

(% class="table-bordered" style="margin-left:auto; margin-right:auto; width:358px" %)

30

|=(% style="width: 79px;" %)Series|=(% style="width: 276px;" %)Number of Alarm upload to Cloud

31

|(% style="width:79px" %)8000-R|(% style="text-align:center; width:276px" %)200

32

|(% style="width:79px" %)9000-R|(% style="text-align:center; width:276px" %)200

33

|(% style="width:79px" %)3000ig|(% style="text-align:center; width:276px" %)20

34

|(% style="width:79px" %)8000ig|(% style="text-align:center; width:276px" %)200

35

|(% style="width:79px" %)MD|(% style="text-align:center; width:276px" %)20

36

)))

37

38

**Alarm Condition:** It sets alarm trigger condition, there are two types: alarm when ON and alarm when OFF.

39

40

**Alert: **It is used to mark whether the alarm has occurred. if an alarm occurs, the address of "control bit" will be written to 1. If "clear alert when alarm OFF" is checked, the address of "control bit" will be written to 0.

41

42

**Beep when alarm ON: **The beep works when the alarm is triggered. If "beep once" is checked, bit address alarm only beep once and stop.

43

44

**Content: **It is used for setting alarm content (command).

45

46

**Alarm Screen: **Pop-up alarm screen (it need to be sub-screen);

47

48

* **Position: **The location of the screen alarm display.

49

* **Pop-up Interval: **The time of reopen the alarm screen when alarm screen closed.

50

* **Pop-up once: **Pop up alarm screen once, and the screen would not pop up again

51

* **Close window when alarm off: **Automatically close the alarm screen when alarm off.

52

53

(% class="box infomessage" %)

(((

**✎Note:**

* If the "cloud" function is enabled and "upload to cloud" is checked, the communication port of the address in the configuration of the imported bit alarm record must be the same as that of the current project; otherwise, it cannot be used normally.

58

* The number of alarm configuration points reported to the cloud cannot exceed 20, or the sum of imported alarm records and the current alarm records cannot exceed 20. If it exceeds, please reconfigure.

59

)))

60

61

**Operating Procedures of Adding One Alarm**

62

63

* Click "Project"→"Bit Alarm" as below shows.

64

65

(% style="text-align:center" %)

66

[[image:8.Basic Function_html_5f8da20315334bac.png||data-xwiki-image-style-alignment="center" height="144" width="539" class="img-thumbnail"]]

67

68

* Click "Add" button to open "Bit Alarm" setting window.

69

70

(% style="text-align:center" %)

71

[[image:8.Basic Function_html_94a019683b506e15.png||data-xwiki-image-style-alignment="center" height="307" width="554" class="img-thumbnail"]]

72

73

* Set "Bit Address".

74

* Set "Alarm Condition".

75

* Set "Content".

76

* Other settings can be set according to the actual situation".

77

* Click "OK" button to complete settings.

== Word alarm ==

Word alarm is to monitor the word address of a device. If the data meets the set conditions, an alarm will be generated.

82

83

Click "Project"→"Word alarm", it is displayed as the following figure.

84

85

(% style="text-align:center" %)

86

[[image:字报警 1.png||class="img-thumbnail"]]

87

88

**Alarm Name:** You can set alarm name for it. Alarm Name can only consist of (0~~9), (a~~z), (A~~Z), ('_'), (' ') and other non-English characters.

89

90

**Alarm Address: **It is used for setting word address for word alarm, such as HDW0.

91

92

**Data Format: **16-bit unsigned decimal, 16-bit signed decimal, 16-bit BCD, 32-bit unsigned decimal, 32-bit signed decimal, 32-bit BCD, 32-bit float.

93

94

**Group No.: **Group number of word alarm. The name is unique and cannot be duplicated.

95

96

**Upload to Cloud: **The data upload by "word alarm" is stored in the Cloud and it is alarm data. (Only ig series and 8000/9000 series with -R after system upgrade are supported)

97

98

(% class="box infomessage" %)

(((

**✎Note:**

* If the "cloud" function is enabled and "upload to cloud" is checked, the communication port of the address in the configuration of the imported word alarm record must be the same as that of the current project; otherwise, it cannot be used normally.

103

* The number of alarm configuration points reported to the cloud cannot exceed 20, or the sum of imported alarm records and the current alarm records cannot exceed 20. If it exceeds, please reconfigure.

104

105

(% style="margin-left:auto; margin-right:auto; width:358px" %)

106

|=(% style="width: 79px;" %)Series|=(% style="width: 276px;" %)Number of Alarm upload to Cloud

107

|(% style="width:79px" %)8000-R|(% style="text-align:center; width:276px" %)200

108

|(% style="width:79px" %)9000-R|(% style="text-align:center; width:276px" %)200

109

|(% style="width:79px" %)3000ig|(% style="text-align:center; width:276px" %)20

110

|(% style="width:79px" %)8000ig|(% style="text-align:center; width:276px" %)200

111

|(% style="width:79px" %)MD|(% style="text-align:center; width:276px" %)20

112

)))

113

114

**Record alarm:** Whether to record the alarm history data of word alarm, if checked, it will be saved in the designated storage location.

115

116

**Not save alarm OFF:** If checked, after the alarm is dismissed, the corresponding alarm records will be deleted from the log file.

117

118

**Alarm Condition**: Alarm is triggered when designated address meets the alarm condition, it provides four conditions;

119

120

1. **High alarm:** Alarm is triggered when it reaches high limit. It can be a constant or a variable

121

1. **Low alarm:** Alarm is triggered when it reaches low limit. It can be a constant or a variable

122

1. **Range alarm:** Alarm is triggered when it exceeds the range. It can be a constant or a variable

123

1. **Equivalent alarm: **Alarm is triggered when the value equals to the given data. It can be a constant or a variable

124

125

**Alarm Info: **It is used for setting alarm content (command);

126

127

**Alert: **It is used to mark whether the alarm has occurred. if an alarm occurs, the address of "control bit" will be written to 1. If "clear alert when alarm OFF" is checked, the address of "control bit" will be written to 0.

128

129

**Alarm Screen: **Pop-up alarm screen (it need to be sub-screen);

130

131

1. **Position: **The location of the screen alarm display.

132

1. **Pop-up Interval: **The time of reopen the alarm screen when alarm screen closed.

133

1. **Pop-up once: **Pop up alarm screen once.

134

1. **Close window when alarm off: **Automatically close the alarm screen when alarm off.

135

136

**Beep when alarm ON: **beep works when the alarm is triggered, in the default mode, the beep works until the alarm is released.

137

138

**Beep once:** Beep works once, when alarm is triggered.

**Alarm List**

It displays all the word alarm lists; it will show the alarm information;

143

144

**Operating Procedures of Adding One Alarm**

145

146

* Click "Project"→ "Word Alarm" as below shows.

147

148

(% style="text-align:center" %)

149

[[image:8.Basic Function_html_1b59522c984cd7c2.png||height="144" width="492" class="img-thumbnail"]]

150

151

* Click "AddClick" button to open "Word Alarm" setting window.

152

153

(% style="text-align:center" %)

154

[[image:8.Basic Function_html_942107c81fc6901c.png||height="307" width="554" class="img-thumbnail"]]

155

156

* Set Basic information of word alarm.

157

* Set "Content".

158

* Other settings can be set according to the actual situation.

159

* Click "OK" button to complete settings.

160

161

== How to show the variables in alarm info? ==

162

163

We can write some codes in the alarm info and add variables to the alarm info to make the alarm info clearer.

164

165

**{Address,Data format}**

166

167

(% style="height:10px; width:250px" %)

|=Letter|=Mean

|B|Binary

|O|Octal

|U|Unsigned

|H|Hex

|b|BCD

|F|32-bit floating

|S|Signed

|C|String

|W|Word

|D|Dword

|T|Dword string

Example:

Unsigned,BCD,32-bit floating,Signed:

184

185

{HDW100,UW2.1} ~-~-- add a variables into the alarm info:address-HDW100 ,data format-unsigned,Word,2 Integer,1 Decimal.

Binary,Octal,Hex:

{HDW100,HD8} ~-~-- add a variables into the alarm info:address-HDW100 ,data format-Hex,Dword,8 Integer.

String

{HDW100,C32} ~-~-- add a variables into the alarm info:address-HDW100 ,data format-String,32 length.

194

195

196

**HMI Alarm Demo Download Link**

197

198

[[https:~~/~~/drive.google.com/open?id=1Llq03CMISM_1mMIfU308hxFbs4rGdQGP>>url:https://drive.google.com/open?id=1Llq03CMISM_1mMIfU308hxFbs4rGdQGP]]

= **Recipe** =

== Overview of recipe ==

203

204

Recipes are composed of multiple groups of information materials with the same structure and different data. Due to the sameness of these materials, users can edit them into a group of recipes to facilitate data transfer between HMI and PLC. Therefore, this function can be utilized for information that has a similar structure to achieve efficient and correct transmission.

205

206

Data operation of recipe: Upload and download. Upload refers to reading the data of [The set address] group and writing the data of this group to the corresponding recipe file. Download refers to reading a group of data from the recipe file and assigning the group of data to [The set address].

207

208

The recipe data can be stored in external equipment, such as USB flash disk and SD card. The whole recipe data can be viewed with the [Recipe record] object.

209

210

(% class="wikigeneratedid" id="HExample" %)

211

**Example**

212

213

Taking automobile paint spraying as an example, suppose that when a newly manufactured automobile needs to be painted, it needs to spray different colors (red, green and blue) on the top, bottom and outside of the automobile, and the original colors provided are only red, green and blue. At this time, to spray different colors, it needs the appropriate ratio of these three colors, and the spraying time of different parts is different. At this time, the function of recipe needs to be executed. Check Table 1 for details.

214

215

Table 1 Example recipe

|Top|2|2|1|30

|Bottom|3|1|2|40

|Outside|2|3|3|20

From the above table, one group of recipes is needed when spraying different parts, and three groups of recipes can be established, and each group of recipes has four ingredients: Red, Green, Blue, Spraying time. The value of each ingredient is different in different groups of recipes.**Recipe configuration**

223

224

The recipe function needs to be used with the recipe configuration area and [Recipe record] object. Click [Recipe] in the [System configuration/Record setting] in the upper left side of the software [[image:1698393787529-717.png]]and the following interface will pop up:

225

226

(% style="text-align:center" %)

227

[[image:1.png]]

228

229

Click [Add] to pop up the recipe setting interface, as shown in the following figure:

230

231

(% style="text-align:center" %)

232

[[image:2.png]]

233

234

|Recipe configuration options|Description|Notice

235

|Recipe name|Name the current recipe|Note: Recipe name can only consist of (0~~9), (a~~z), (A~~Z), ('_'), ('') and other non-English characters.

236

|Group number|Configure the group number of the current recipe, ranging from 0 to 1000|

237

|Number of ingredients|Configure the number of the current ingredient, ranging from 0 to 1500|

238

239

|Data configuration options|Description|Notice

240

|Starting address|The data of group in the recipe file is read out and displayed in the address, which will be automatically assigned according to the set data format of each ingredient. For example, if each group has 10 ingredients, the ingredient format is 16-bit unsigned decimal number, and the starting address is HDW0, then 10 addresses (HDW0-HDW9) correspond to 10 ingredients respectively, the values in HDWO correspond to the values in ingredient 1, the values in HDW1 correspond to the values in ingredient 2, and so on.|

241

|Recipes are read and written at different addresses|When "recipe written and read address are different" is checked, the address configured by the read address is only used for recipe read data operation, and the address set in this area is used to control recipe written data operation.|

242

|Data format|Configure the data format of this recipe. There are 9 modes of data format: 16-bit BCD code, 16-bit signed decimal, 16-bit unsigned decimal, 32-bit BCD code, 32-bit signed decimal, 32-bit unsigned decimal, 32-bit (single-precision) floating points, 64-bit (double-precision) floating point, string.|(% rowspan="2" %)(% class="box infomessage" %)

243

(((

244

**✎Note:** The data format set here is for all components of the recipe, that is, the data format of all components in a recipe is consistent.

245

)))

246

|Decimal point position|Configure the selection of integer and decimal places of data.

247

|Enable discontinuous addresses|If checked, the address of the recipe list can be modified.|

248

|Language|Recipe display language is selectable.|

249

|Recipe list|The recipe list displays the configured recipe parameter information in the list according to the settings. The parameters of each ingredient in the recipe list can be modified at the same time: For example, the name of the ingredient, the data format of the ingredient, the address of the ingredient, and directly filling in the data of each ingredient in each group.|

250

|Insert group|Click [Insert group], enter the number of groups to insert, and the corresponding row will be added to the recipe list.|

251

|Delete group.|Click [Delete group] to select the group to delete|

252

|Insert ingredient|Click [Insert group], enter the number of groups to insert, and the corresponding row will be added to the recipe list.|

253

|Delete ingredient|Click [Delete ingredient] to select the ingredient to delete.|

254

|Data import|Import existing data files, supporting .xlsx .xls .csv format.|

255

|Data export|Export configured recipe data|

256

257

Traditional recipe is composed of multiple groups of information with the same structure and different data. Due to the similarity of these information, you could edit them into a set of recipes to facilitate the transfer of data between HMI and PLC.

Data operation

1. **Read:** Read a group of data from the recipe file and assign the group of data to the set address.

262

1. **Write: **Read a group of data from the set address and assign the group of data to the corresponding recipe file.

263

264

PI Series HMI has Recipe function, Recipe function keeps data in the HMI, used to download the data from HMI to designated device addresses, or upload the data from device addresses to HMI.

265

266

The maximum number of group in recipe is 1000, and the maximum number of member in each group is 1500.

267

268

Recipe could store the data in USB flash disk and SD card and view the recipe data by object "Recipe display". It has two mode: simple mode and advanced mode.

269

270

1. **Simple: **Only support the data operation of one recipe file, including read and write.

271

1. **Advanced:** Support the data operation of multiple recipe files, including read, write, insert and index. View and select recipe file by object "File list".

272

273

Recipe function settings will be display in "[[Recipe display>>http://docs.we-con.com.cn/wiki/pistudio/view/Helps/06.Objects/#HRecipedisplay]]" object.

**Description**

(% style="text-align:center" %)

278

[[image:8-1Recipe.png]]

**Basic**

* **Recipe Folder:** Give Recipe folder name (It can be used, when setting Recipe display object);

283

** (% class="box infomessage" %)

284

(((

285

**✎Note: **Recipe Folder name can only consist of (0~~9), (a~~z), (A~~Z), ('_'), (' ') and other non-English characters;

286

)))

287

* **Group: **Set the recipe group number, the number of elements, the data format. The data format has 8 modes: 16-bit signed decimal, 16-bit unsigned decimal, 16-bit BCD, 32-bit signed decimal, 32-bit unsigned decimal, 16-bit BCD, 32-bit floating point number, 64-bit (double-precision) floating-point number, string, and the choice of data integer and decimal places.

288

* **Elements:** It sets members' initial number of each group;

289

* **Data Format:** There are some formats can be supported in Recipe, like 16-bit BCD, 16-bit signed, 16-bit unsigned, 32-bit BCD, 32-bit signed, 32-bit unsigned, 32-bit floating and string. If each member requires different formats, please set it one by one in form;

290

* **Decimal: **It sets integer and scale digits;

291

292

**Mode Selection: **Select Simple or Advanced mode. Recipe file is divided into simple mode and advanced mode. Only in advanced mode can exist multiple recipe files used at the same time. (used wiht file list onject), Simple mode can only support a recipe file; Aadvanced mode can insert group information and reordered.

293

294

Function address: all operations are done through function addresses, different operating value is as follows:

295

296

* = 0: no operation;

297

* = 1: trigger read data;

298

* = 2: new trigger or update (If there is group number, it updates.)

299

* = 4: insert (only valid in advanced mode)

300

* = 8: delete (Delete according to the writing group number. If write and read address are consistent, refer to the reading group number);

301

* = 16: delete and sorted ((Delete according to the writing group number. If write and read address are consistent, refer to the reading group number)

302

* = 64: import CSV recipe file.

303

304

**Use Multiple File**

305

306

Check it to use more than one recipe file in HMI, but this option only valid in [Advanced mode];

**Select language**

The text in HMI can be in 8 languages, user can set language in here;

**Address**

1. **Group:** This address is for selecting group number;

315

1. **Start: **This is starting address is for reading and writing in recipe, PIStudio will automatically assigns addresses for each members;

316

1. **File(16 words): **This address only available when enable the Use Multiple File. This setting address is for input the recipe file's filename.

**Use Index**

If the value from Group address is changed, Read address will display the new data according to new group number immediately. Relatively, if the data of write address is changed, the corresponding group from table is also changed.

**Query by Element**

Enable it for querying group by specify element, select a primary key from all the elements, except the group number. This element value from all groups must be unique if want to set as primary key;

325

326

(% class="box infomessage" %)

327

(((

328

**✎Note: **When this option is enabled, Group address will be invalid.

329

)))

330

331

**Use Independent Write Address**

332

333

To separate Recipe read address and write address.

**Use Insert**

It inserts data into the specified group, if the specified group already exists, it would not cover the original data, while it will move the original group next one after it.

338

339

**Discontinuous Address**

340

341

Whether enable the non-consecutive recipe operation addresses or not. If disabled, the recipe address will recover as the continuous addresses.

342

343

(% class="box infomessage" %)

344

(((

345

**✎Note: **This function only supported in HMI+, i series, ie series, ig series.

346

)))

347

348

**Description of adcanced mode**

349

350

According to the recipe configuration information in Figure 2 above. The function address is HDW70, and each function configuration corresponds to the group number address, recipe element address and recipe file name address. The recipe information configured in figure 2 can be displayed in the table in figure 3 with the "Record Display" object.

351

352

[[image:image-20220806111333-1.jpeg]]

353

354

**Read recipe**: Input 1 to the file name, when the group number addresses HDW100=1 and HDW70=1 (read), the element data of the first group (ID=1) is written to the recipe address from the recipe file. As shown in Figure 3 above: HDW105=1, HHDW106=2, HDW107=3, HDW108=4, HDW109=5.

355

356

**Write recipe**: Input 1 to the file name, when the group number addresses HDW101=4 and HDW70=2 (write), the data will be read from the recipe address and written to the corresponding group of the recipe file. As shown in figure 3 above: HDW110=20, HHDW111=21, HDW112=22, HDW113=23, HDW114=24. Write the data of this set to the elements of ID=4 in the recipe table (if there is no data of Group 4 in the recipe file, a new set of data will be added; If there is data of Group 4 in the original recipe, the original data will be overwritten and the latest data will be displayed in the recipe file).

357

358

**Index recipe**: When the file name is input 1, when the group number address HDW102=3, the data of ID=3 (Group 3) in the recipe file will be directly displayed in the component address of the index, that is, HDW115=11, HHDW116=12, HDW117=13, HDW118=14 and HDW119=15. If the data of the index component address is modified, the modified data will be automatically filled into the table of the recipe file, that is, the data of the recipe file will be automatically updated after the data is modified.

359

360

[[image:image-20220806111355-2.jpeg]]

361

362

**Insert recipe**: Input 1 to the file name, when the group number addresses HDW103=3 and HDW70=4 (insert), the data of the 3rd group will be inserted, but the data of the third group already exists in the original recipe file (see Figure 3 above), then the original data will be moved down by one group, that is, the original 3rd group will become the 4th group, and so on, and HDW120=16, HHDW121=17, HDW122=18, HDW123=19 and HDW124=20 will be written into the new 3rd group of the recipe file at the same time. The results are shown in Figure 4 above.

363

364

When the group number address HDW101=2 (**The delete function only works on the group number of the write function**), HDW70=8 (delete), the data in the recipe file with ID=2 (Group 2) will be deleted.

365

366

When the group number address HDW101=5 (**The delete function only works on the group number of the write function**), HDW70=16 (delete and sort), the data of ID=5 (Group 5) in the recipe file will be deleted, and the original ID=6 (Group 6) data will be reordered to become the new Group 5 data, the original ID=7 (Group 7) data will be reordered to become the new Group 6 data, and so on.

367

368

**Recipe Demo Download Link: **[[Download>>url:https://drive.google.com/open?id=1Cjbq_tW-NIirHFBpxt47g7IKvoYaWqUR]]

369

370

== Calling CSV recipe file ==

**Overview**

The recipe files used by the regular series HMI are in CSV format, and the recipe files used by the current series HMI are in database format. In order to be compatible with CSV format recipe files on the current series of HMI, please follow the instruction when using it.

**Operations**

Create the recipe as it is configured. The default recipe file name is “1. rcp2”, which is placed in folder 123, as shown in the following figure.

379

380

(% style="text-align:center" %)

381

(((

382

(% style="display:inline-block" %)

383

[[Figure 1>>image:image-20220806100702-2.jpeg]]

384

)))

385

386

2. Place a "Recipe Record Display" object and a "File List" object on the project screen for viewing the recipe files in the folder 123, and the address configuration in the object should be consistent with the above configuration.

387

388

(% style="text-align:center" %)

389

[[image:image-20220806100753-3.jpeg]]

390

391

By configuring the address in the table and combining the recipe function, the CSV recipe files of regular series are imported.

392

393

|=Address range|=Object type|=Address function

394

|HSW1050 to 1065|Text input object|Enter the CSV recipe file name to import

395

|HSW1066|Numerical input object|Import CSV file type:(((

396

* = 0: Custom CSV file (all data in the file is valid)

397

* = 1: Normal recipe file for regular series HMI (the data in line 1 of the file is invalid)

398

* = 2: Special recipe file for regular series HMI (the data in line 1 and 2 and column 1 of the file are invalid)

399

)))

400

|HSW1067|Numerical input object|(((

401

Where the CSV file is saved:

402

403

* = 0: In the CsvFile directory of U disk

404

* = 1: In the CsvFile directory of the SD card

405

406

**The path for offline simulation is: C:\ HMIEmulation\ CustomFileDir\ CsvFile**

407

)))

408

|HSW242|Numerical input object|Returns the results of the csv import:(((

409

* = 37: CSV file imported successfully

410

* = 38: CSV file import failed

411

)))

412

413

**Select CSV recipe file (take U disk as an example):**

414

415

Using the file list object, select the recipe file in the U disk by path, and configure the recipe file name address directly to the special address HSW1050 in the above table, which can directly detect the CSV file in the U disk; Select the recipe file in the file list, and write the selected recipe file name into the recipe file name: In HSW1050 to 1065.

416

417

Use the special address of the above table to configure the path of the CSV file: HSW106, configure recipe file name: HSW1050 to1065

418

419

Use HSW1066 address to select the corresponding CSV recipe file type.

420

421

* HSW1066 = 0: Import a user-defined CSV recipe file (all data in the custom CSV file must be valid);

422

423

(% style="text-align:center" %)

424

[[image:image-20220806101129-5.jpeg]]

425

426

* HSW1066=1: Import the normal recipe file of regular series HMI (the data in line 1 of the file is invalid);

427

428

The data in line 1 of the normal recipe file is used to define the format of the recipe and will not be imported into the recipe table as recipe information, **but you must ensure that the data in line 1 representing the elements and number of groups is correct, otherwise the CSV recipe file will fail to be imported.**

429

430

(% style="text-align:center" %)

431

[[image:image-20220806101520-6.jpeg]]

432

433

* HSW1066=2: Import the special recipe file of regular series HMI (the data in line 1, 2 and column 1 of the file are invalid);

434

435

In the special recipe file, line 1 is used to define the format of the recipe, line 2 is used to define the element name of the recipe, and column 1 is used to define the group name of the recipe, so lines 1, 2 and column 1 of the special recipe will not be imported into the recipe table as recipe information. **During use, ensure that the data such as the number of groups and elements representing the recipe format in the first line are correct, otherwise the import of the CSV recipe file will fail.**

436

437

(% style="text-align:center" %)

438

[[image:image-20220806102610-7.jpeg]]

**Perform import**

After configuring the saving path of CSV recipe file, the name of recipe file and the type of recipe according to the above steps, the method of transferring CSV file to DB file is as follows:

443

444

* Configure the DB recipe file name by text input object: HDW500 = 3 (recipe file configured in Figure 1),

445

* Set the recipe function address to: HDW1000 = 64 (the function address configured in Figure 1),

446

* Transform the CSV recipe file in U disk into DB recipe file with file name “3.rcp2”.

447

448

**DB recipe file for storing CSV data:**

449

450

Simple mode: When the recipe file is set to simple mode, the file of CSV data is saved as the DB recipe file of 1. rcp2 by default.

451

452

Advanced mode: When the recipe is enabled in advanced mode (multi-file recipe), the imported CSV file data is saved to the file recorded at the recipe file address HDW500 (the address configured in Figure 1).

**Import results:**

* HSW242 = 37: Import succeeded;

457

* HSW242 = 38: Import failed.

**Precautions:**

* Ensure that the data format of each element in the CSV file is the same as the recipe data format set in the software (DB), and ensure that the elements of each row in the valid data area is the same as the elements set in the software (DB);

462

* When the elements of a line in CSV file is more than the elements set in the software (DB), it will prompt the import failure;

463

* When the CSV file imported into the regular series HMI is a recipe file, the data representing the recipe format (elements, number of groups, whether it is a special recipe) in line 1 must be correct, otherwise the import of CSV file will fail.

464

465

== **Recipe record function** ==

**Basic setting**

(% style="text-align:center" %)

470

[[image:3.png]]

471

472

Recipe selection: Select the recipe name to be displayed. The list is all the recipes configured in the recipe. If the list is empty, add the recipe in [Recipe].

473

474

Recipe shortcut key setting:

475

476

Add data: Used to add groups.

477

478

Delete data: Used to delete the selected configuration

479

480

Upload recipe: Used to upload the address data of the selected group to the corresponding group in recipe records.

481

482

Download recipe: Used to download the address data of the selected group to the corresponding group in recipe records.

483

484

Import recipe: Used to import the existing recipe files.

485

486

Export recipe: Used to export the current recipe as a file.

**Graphic**

(% style="text-align:center" %)

491

[[image:4.png]]

492

493

Style selection: Styles can be switched or customized.

494

495

Background configuration: Set the recipe background, including background color and transparency.

496

497

Table configuration: Set the appearance of recipe table area, including row background color, row spacing color, horizontal header background color, vertical header background color, horizontal header text color, vertical header text color, text color, row selected color, name color, line color and cell style.

**Expansion**

(% style="text-align:center" %)

502

[[image:5.png]]

503

504

Object lock: With the interlock address, the object is locked and the lock icon is displayed (upper left corner of the object) when the lock address is 0, and the bit switch is operable only when the bit pointed by the interlock bit address is 1. To lock the bit switch when the interlock bit address is 1, just check "Lock in ON".

505

506

Object lock icon: Icons will not display when the [Not display “Lock” icon] option is checked. Icon display will adapt to the change of object size.

507

508

Gray level display: When the object is locked, the text message will be grayed out.

509

510

== **New recipe function address** ==

511

512

In recipe, new special address is used as Function address.

513

514

**Address Type:** RPG

515

516

(% style="text-align:center" %)

517

[[image:企业微信截图_17570533194720.png]]

518

519

(% style="text-align:center" %)

520

[[image:企业微信截图_17570534728083.png]]

521

522

(% class="box infomessage" %)

523

(((

524

Note: There is a set of function address in each recipe.

525

)))

526

527

|(% style="width:107px" %)Name|(% style="width:162px" %)Data format|Length|Function

528

|(% style="width:107px" %)File name|(% style="width:162px" %)String|15 word address|Input file name

529

|(% style="width:107px" %)Record select|(% style="width:162px" %)16-bit unsigned decimal|(((

1 word address

(0-65535)

)))|Currently selected record, numbered starting from 0. When the record selection value changes, the corresponding value will be updated.

534

|(% style="width:107px" %)Function address|(% style="width:162px" %)16-bit unsigned decimal|(((

1 word address

(0-65535)

)))|(((

Enter a specific value to send a command to the selected record

540

541

"1": Add a new recipe record

542

543

"2": Delete the selected recipe record

544

545

"3": Upload the recipe

546

547

"4": Download the recipe

548

549

"5": Update the selected recipe record

550

)))

551

|(% style="width:107px" %)Result|(% style="width:162px" %)16-bit unsigned decimal|1 word address (-32768~-~-32767)|(((

552

View the result of executing the command.

553

554

Display "1": Successfully executed the command

555

556

Display "2": The record limit has been reached and no new records can be added.

557

558

Display "4": No corresponding option

559

560

Display "8": unknown command

561

562

Display "16": recipe download failed.

563

564

Display "32": recipe upload failed.

565

566

Display "64": recipe update failed.

567

)))

568

|(% style="width:107px" %)Record count|(% style="width:162px" %)16-bit unsigned decimal|(((

1 word address

(0-65535)

)))|Display the number of records in the current recipe

573

|(% style="width:107px" %)Element address|(% style="width:162px" %)16-bit unsigned decimal|(((

1 word address

(0-65535)

)))|Element address

= (% style="color:inherit; font-family:inherit; font-size:29px" %)**Traditional recipe**(%%) =

582

583

Traditional recipe is composed of multiple groups of information with the same structure and different data. Due to the similarity of these information, you could edit them into a set of recipes to facilitate the transfer of data between HMI and PLC.

584

585

Traditional recipe function is valid only when the LEVI project is converted to the PI project, and the original project uses the traditional recipe.

586

587

(% class="box infomessage" %)

588

(((

589

**✎Note**: Currently, only HMI+, i series, ie series, and ig series support the traditional recipe.

590

)))

591

592

== Simple recipe mode ==

593

594

Click the "Traditional Recipe" [[image:8-2TraditionalRecipe.png]] in the "Data tool" bar in the upper side of the software, and the following interface will pop up:

595

596

(% style="text-align:center" %)

597

[[image:8-3TraditionalRecipeConfigScreen.png||class="img-thumbnail"]]

**✎Note**:

* The recipe folder name can only consist of (0~~9), (a~~z), (A~~Z), ('_'), ('').

602

* The element name of the recipe cannot include following 5 special characters: " **,** " , " **|** " , " **<** " , " **>** " , " **&** " .

== Recipe display ==

Select the file type "Traditional recipe file" in object "Recipe Display", and it is recommended to fill in the traditional recipe group number HSW1612 to the address of select line.

607

608

(% class="box infomessage" %)

609

(((

610

**✎Note**: The Recipe Display can display up to 50 groups of 100 elements by default, which can be to display out of range by enabled "Address Control". After the "Address Control" is enabled, the display group number can be reached to 100. If want to display more than 100, please adjust the "Start Group" from "Address Control" to index the display group, as following shown:

611

)))

612

613

(% style="text-align:center" %)

614

[[image:8-4TraditionalRecipeDisplayConfigScreen.png||class="img-thumbnail"]]

615

616

== Recipe transmission address ==

617

618

The special addresses used in the Recipe are shown in the following table:

619

620

(% class="table-bordered" %)

621

|=Address|=Description|=Function

622

|HSW1611|Traditional Recipe transfer operation.|(((

623

~=1: Recipe download.

~=2: Recipe upload.

)))

|HSW1612|Traditional Recipe group number.|Traditional Recipe group number.

|(((

HSW242

)))|(((

Recipe operation result prompt:

632

633

Upload: Data is written to recipe file from address.

634

635

Download: Data is written to the address from recipe file.

636

)))|(((

637

~=1: Recipe download, start.

638

639

~=2: Recipe download, execution error.

640

641

~=6: Recipe download, successful.

642

643

~=7: Recipe upload, start.

644

645

~=8: Recipe upload, execution error.

646

647

~=11: Recipe group name does not exist.

648

649

~=12: Recipe upload, successful.

650

)))

651

652

== **Recipe index** ==

653

654

The recipe index address RPW is mainly used for editing traditional recipes, and it is more convenient to modify the data and display of recipes. Only need to modify and display the data of the recipe file through "Numeric Input/Display" Object and "Word Switch".

655

656

The recipe index area (RPW)'s instruction as follows:

657

658

1. RPW~*~*~#~#~#~#, a total of six digits, the first two ~*~* represent the Recipe group number, ~#~#~#~# represents the element order number. For example, RPW010000 indicates the 1st element of the Recipe group No.1, and RPW110002 indicates the 3rd element of the Recipe group No.11.

659

1. If the indexed group number or element number does not exist, the value of RPW defaults to zero. For example, RPW110011 represents the 12th element of the Recipe group No.11. If it does not exist, the value returned by accessing RPW110011 is zero. The value written in RPW110011 will not be saved to the recipe file.

660

661

* **✎Note**: As long as RPW~*~*~#~#~#~# exists, any object "writes" to HPW~*~*~#~#~#~# will be saved to the recipe file.

662

663

(% start="3" %)

664

1. The RPW register only supports word address access.

665

1. It can be known from the coding method of RPW~*~*~#~#~#~# that the range of RPW is from RPW000000-RPW990450, wherein the range of group number is 0-100, and the range of element is 0-450.

== Recipe example ==

The recipe index makes the modification and display of recipe data more convenient. Only need to modify and display the data of the recipe file through "Numeric Input/Display" Object and "Word Switch".

670

671

Edit the recipe configuration, create three groups of recipes, 4 elements for per group: Red, green, blue, spraying time, as following shown:

672

673

(% style="text-align:center" %)

674

[[image:8-5TraditionalRecipeCaseConfig.png]]

675

676

RPW 0~~3 can display the data of group for the selected line. RPW10000~~10003, RPW20000~~20003, RPW30000~~30003 each address can display the single element. Directly modify the content of the RPW address and then modify the recipe data, as following shown:

677

678

(% style="text-align:center" %)

679

[[image:8-7TraditionalRecipeCaseShowNoOpera.png]]

680

681

After selecting the 2nd group, trigger the download button to download the whole group data to the corresponding element address (For this case, the data will write into HDW0~~3), or trigger the upload button to upload the content of the element address to the specified recipe group.

682

683

(% style="text-align:center" %)

684

[[image:8-6TraditionalRecipeCaseShow.png]]

= **Trend chart** =

Trend chart function is used for displaying the real-time data in HMI as curve graph, which X axis represent as time, Y axis represent as data.

689

690

Click "Project" → "Trend chart", it will pop up the following screen. Click "Add" to creat new curve record.

691

692

(% style="text-align:center" %)

693

[[image:趋势图配置 001.png||class="img-thumbnail"]]

**Settings**

(% style="text-align:center" %)

698

[[image:趋势图设置 2.png||height="507" width="866"]]

699

700

**(1) Basic settings**

701

702

1. **Curve NO.: **It is for setting curve number,

703

1. **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.

704

1. **Curve (1~~8):** It is for setting the number of curves. The default is 3.

705

1. **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.

**(2) Sample Type**

1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.

710

1. **Sample unit:** 100ms.

711

712

**(3) Quick Setting**

713

714

1. **Data format: **It is for setting all the curves, select the data format for all curves, and setting the reading addresses for curves. There are as follows.

715

716

(% style="text-align:center" %)

717

[[image:趋势图设置 3.png||class="img-thumbnail"]]

718

719

(% start="2" %)

720

1. **Sample address: **Fill in the start address that read the device data. If the sampl address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.

721

722

**(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.

723

724

(% class="box infomessage" %)

725

(((

726

**✎Note: **Curve names can only consist of Chinese characters, (0~~9), (a~~z), (A~~Z), ('_') (' '), and other non-English characters.

727

)))

728

729

**Trend Chart Demo Download Link**

730

731

[[https:~~/~~/drive.google.com/open?id=1smnaAvSxOWC0WQK4_uvqHXWn4vUZxGJC>>url:https://drive.google.com/open?id=1smnaAvSxOWC0WQK4_uvqHXWn4vUZxGJC]]

732

733

= **History XY plot** =

734

735

Different from TrendChart, uses need to set history XY curve items in project. Please click "Project"-> "History XY Plot" to open the setting screen.

736

737

Recipe function settings will be display in "[[History XY Plot>>path:https://docs.we-con.com.cn/bin/view/PIStudio/08.Basic%20Function/#HHistoryXYplot]]" object.

738

739

(% style="text-align:center" %)

740

[[image:历史XY 2.png||class="img-thumbnail"]]

741

742

(% style="text-align:center" %)

743

[[image:历史XY 3.png||class="img-thumbnail"]]

744

745

**(1) Basic settings**

746

747

1. **Curve NO.: **It is for setting curve number,

748

1. **Curve Name:** It is for setting curve name. The length limitation is 31 bytes.

749

1. **Curve (1~~8):** It is for setting the number of curves. The default is 3.

750

1. **Dots of one curve: **It is for setting dots number of each curve. The default is 1000, but the maximum dots are 10,000 for all the curves.

**(2) Sample Type**

1. **Sample method:** There are two types, one is Cycle sample, the other is Trigger cycle sample. If you select Trigger cycle same mode, the trigger sample address is required to edit.

755

1. **Sample unit:** 100ms.

756

757

**(3) Quick Setting**

758

759

1. **Data format: **It is for setting all the curves, select the data format for all curves, and setting the reading addresses for curves. There are as follows.

760

761

(% style="text-align:center" %)

762

[[image:image-20220616145435-1.png]]

763

764

(% start="2" %)

765

1. **Sample address: **Fill in the start address that read the device data. If the sample address is consecutive, check "use continuous address". For example, set HDW0 as start address, curve number is 3, then the HDW0 is for Curve 1, HDW1 is for Curve2, HDW2 is for Curve 3.

766

767

**(4) Curve Table:** The sample address you have set would display on it. Click the corresponding box to modify the content.

768

769

(% class="box infomessage" %)

770

(((

771

**✎Note: **Curve names can only consist of Chinese characters, (0~~9), (a~~z), (A~~Z), ('_') (' '), and other non-English characters.

772

)))

773

774

**Operating Procedure**

775

776

* Click "Project" → "History XY Plot" to open the function selecting windows.

777

778

(% style="text-align:center" %)

779

[[image:8.Basic Function_html_5da6ca44bd28acbe.png||height="144" width="533" class="img-thumbnail"]]

780

781

* Click "Add" button to open "History XY Plot” setting windows.

782

783

(% style="text-align:center" %)

784

[[image:8.Basic Function_html_6345b50ea55168fa.png||height="307" width="554" class="img-thumbnail"]]

785

786

* Setting the function of History XY Plot.

787

* Click "OK" to save the setting.

**Download Link**

[[https:~~/~~/drive.google.com/open?id=1t4_HuRmIJJ-B5ryA2kVMadD9FywKhZ4r>>url:https://drive.google.com/open?id=1t4_HuRmIJJ-B5ryA2kVMadD9FywKhZ4r]]

792

793

= (% style="color:inherit; font-family:inherit; font-size:29px" %)**Data record**(%%) =

794

795

The data record function is organized according to the structure below. In a project, there can be multiple record groups, each record group containing multiple channels. Different groups have different sampling times.

796

797

The topology is shown in the following figure.

798

799

(% style="text-align:center" %)

800

[[image:8.Basic Function_html_1b4bd09dafa7e049.png||height="332" width="554" class="img-thumbnail"]]

801

802

The data record stored in SD card is also organized according to the above figure.

803

804

The sample time and save time is consistent in the same record group. There are multiple channels in the group, When the sampling time is up, every channel would collect data to PLC register according to its own address.

805

806

**Sampling interval: **The interval between two consecutive samples was recorded.

807

808

As long as the project uses the data record function and supports the large-capacity storage module, the system will sample data according to the set sampling interval and save data according to the set saving interval.

809

810

For the file storage of data, see the file size configuration during data record configuration.

✎**Note: **

After enable the Cloud and check the box of Upload to Cloud, the communication port settings of the address in the imported Data record configuration must be the same as the communication port settings of the current project, otherwise it cannot be used normally.

815

816

The number of Data records upload to Cloud shall not exceed the limit value, or the sum of the imported Data records and the number of existing alarm records shall not exceed the limit value. the specific limitation as following table:

817

818

(% style="margin-left:auto; margin-right:auto; width:513px" %)

819

|=(% style="width: 70px;" %)Series|=(% style="width: 442px;" %)Number of Data Record upload to Cloud

820

|(% style="width:70px" %)8000-R|(% style="text-align:center; width:442px" %)100

821

|(% style="width:70px" %)9000-R|(% style="text-align:center; width:442px" %)100

822

|(% style="width:70px" %)3000ig|(% style="text-align:center; width:442px" %)50

823

|(% style="width:70px" %)8000ig|(% style="text-align:center; width:442px" %)100

824

|(% style="width:70px" %)MD|(% style="text-align:center; width:442px" %)50

825

826

The record group name can only be composed of Chinese characters, (0~~9), (a~~z), (A~~Z), ('_'), ('') and other non-English characters.

827

828

Channel name cannot incloud following symbols: ：" , ", " | ", " < ", " > ", " & ".

829

830

(% class="wikigeneratedid" id="HSettings" %)

831

**Settings**

832

833

(% style="text-align:center" %)

834

[[image:数据记录设置 1.png||height="533" width="848" class="img-thumbnail"]]

835

836

**Operating Procedures**

837

838

1. Click "Project"->"Data record" as below shows.

839

1. Click "Add" button to open "Data record" setting window.

840

1. Enter group name, the default is "GroupName0"

841

1. Select "Trigger function" mode, such as "No trigger".

842

1. Set "Total channels", such as 3.

843

1. Click "Apply" button.

844

1. Set Sample cycle, such as 15.

845

1. Set "Start channel" in "Quick settings", such as 4 0.

846

1. Check group information in "Channel list" as below.

847

1. Click "Save" button to complete settings.

848

849

The figure above display the group of current project. The data record file would stored in "DataLogFile" folder, and the data of every group would have a data file. The file suffix is in "db" format.

✎**Note: **

* For HMI series 8000 and above, the size of a single file cannot exceed 300M and the total file capacity cannot exceed 1000M.

854

* For HMI series 3000, the size of a single file cannot exceed 4M and the total file capacity cannot exceed 10M.

855

* If the total amount exceeds the range, an alarm will be given during project compilation.

856

857

(% style="text-align:center" %)

858

[[image:数据记录设置 2.png||height="572" width="850" class="img-thumbnail"]]

859

860

**(1) Group name:** Set group name, and he name should be unique.

861

862

**(2) Trigger function:** There are four modes to trigger record.

863

864

1. **No trigger: **Data will be recorded in every sample time.

865

1. **Trigger to record by sample cycle: **Data will be recorded in every same time, when trigger control bit set ON.

866

1. **Trigger to record once and reset: **Data will be recorded when trigger control bit set ON, and the bit will be reset automatically.

867

1. **Trigger to record once: **Data will be recorded when trigger control bit set ON, and the bit need to be reset manually.

868

1. **Trigger address: **It is only valid when the trigger condition is selected. The monitoring cycle for trigger sampling address is 1s.

869

870

**(3) Total channels (1~~100): **Set the numbers of channels. Click "apply" to view the channel lists on the right record channel.

871

872

**(4) Sampling cycle: **If you check "collect control address", the sampling interval is the value of the address. The unit is second. For example, Sample cycle=15s. It means that records data one time every 15s.

873

874

**Timing address:** It sets address to change sample time when HMI is running;

875

876

**(5) Total records:** It sets data record number in one data record file. If the data file size is beyond the current file size. The old data will be deleted, and the new data will replace the old data. Please remember to back up the old data record file.

877

878

**Abnormal value:** It sets a value, when communication fails, data record will record this value;

879

880

**(6) Upload to Cloud**: The data uploaded by Data Record is stored in the Cloud(Only ig series). The maximum number of record is 20.

881

882

**(7) Quick Settings**

883

884

1. **Start Channel:** It sets the continuous addresses for channels.

885

1. **Data Format: **It sets the same data format for channels.

886

1. **Number of Digits:** It sets the digits’ number for channels.

887

1. **Language Settings**: The text in HMI can be in 8 languages, user can set language in here.

888

889

**(8) Channel List**: Besides quick settings, user can set channel name, address, data format, and so on one by one according to real situation.

**✎Note:**

* After enabling the Cloud function and checking the upload to the Cloud, the communication port settings of the address in the imported Data record configuration must be the same as the communication settings of the current project, otherwise it cannot be used normally.

894

* The range of upload to the Cloud from Data record configuration must not exceed 50, or the total number of imported Data records and the number of currently existing Data records must not exceed 50. If it exceeds, it will prompt you to reconfigure, should reduce the number.

895

* The channel name can only be composed of English characters, (0~~9), (a~~z), (A~~Z), ('_'), ('').

896

* The channel name does not include these 5 special characters: ", ", "| "," <", "> "," & ".

897

* The data would be overwritten automatically if the capacity exceed the maximum capacity. For 8000/9000 series, the size of single file cannot exceed 300MB, and total capacity of data records cannot exceed 1000MB. For 3000/3000i/3000ie series, the size of single file cannot exceed 4MB, and total capacity of data records cannot exceed 10MB. If the total amount exceeds the range , an error will be prompted when the project is compiled.

898

899

You could click here to jump to object "[[Data Record Display>>https://docs.we-con.com.cn/bin/view/PIStudio/06.Objects/#HDatarecorddisplay]]"

= Column Chart =

Use the bar chart to monitor and visualize register data in real time

904

905

== **Y-axis configuration** ==

906

907

Configure the Y-axis parameters, including value type, minimum ,maximum ,data types, and decimal point settings.

908

909

(% style="text-align:center" %)

910

[[image:5.png]]

911

912

== **Channel setting** ==

913

914

Set the channel address to be displayed.

915

916

**Dynamic color:** Change value of a word address to change the color of the channel display.

917

918

Dynamic color sequence: The color sequence number bound to the channel (click to enter the color sequence configuration interface)

919

920

(% style="text-align:center" %)

921

[[image:1.png]]

922

923

(% class="wikigeneratedid" %)

924

**Color sequence configuration interface**

925

926

927

**Upgrade to Global Configuration: **This color sequence is upgraded to the global default.

928

929

**Global Configuration:** When a new bar chart control is created in a project, the color sequence has a default configuration. When you upgrade an existing configuration to a global configuration, the default color sequence for the new control will be the same as the configured color sequence.

930

931

(% style="text-align:center" %)

[[image:2.png]]

**Enable Baseline:** Set baselines on the bar chart.

936

937

**Baseline: **The baseline ID bound to the channel) (click to enter the baseline configuration interface).

938

939

(% style="text-align:center" %)

940

[[image:121.png]]

941

942

**Baseline Configuration:**

943

944

**Value type: **Baseline value type

945

946

(**Fixed value: **baseline value is fixedly set; **Dynamic address:** baseline value is read from address).

947

948

**Upgrade to Global Configuration:** This will make this warning zone the global default configuration.

949

950

Global Configuration: When a new bar chart control is created in a project, the warning zone has a default configuration. When you upgrade an existing configuration to a global configuration, the default configuration for the new control will be the same as the configured one.

951

952

(% style="text-align:center" %)

953

[[image:3.png]]

954

955

== **Appearance setting** ==

956

957

(% class="wikigeneratedid" %)

958

Set a configuration for the X-axis, background color, etc.

959

960

(% style="text-align:center" %)

961

[[image:4.png]]

962

963

== **Function settings** ==

964

965

**Column Update Method：**

966

967

**Periodic Update:** Updates the histogram periodically.

968

969

**Triggered Update: **Controls whether the histogram updates based on an address.

970

971

**Triggered Periodic Update:** Triggers a periodic update of the histogram.

972

973

**Cycle update time: **Periodic update time setting, unit: seconds

974

975

**Function control starting address: **The function of the bar chart can be controlled by the address. The starting address is configured here. For specific functions, refer to the address description list.

976

977

(% style="text-align:center" %)

[[image:0.png]]

== Chart Button ==

[[image:Screenshot 2025-09-09 102850.png||style="float:left"]]

：Menu

：Zoom in

：Zoom out

：Restore button (Reset the chart's zoom level to its original 1:1 ratio)

：Data label hide/show button(Controls hiding/showing of data labels)

：Settings Button

= **User permission** =

**Introduction**

1. User permission is one of expansion function in PI Series HMI; it provides multi-level of permission for control HMI operations.

1013

1. User need to set the user and group during designing project. Different groups have different permission levels for accessing. Each user should be added into the specified group; it is possible to add the same user into different groups.

1014

1. Operating record: it records user operations information, the records files are saved in HMI flash; its path is [~\~\flash~\~\UserOperationLogs.db].

1015

1. When it is on simulator mode, the files are saved in C disk, its path is [C:~\~\WECON\UserMgrFile\UserOperationLogs.db].

1016

1017

(% class="box infomessage" %)

(((

✎**Note: **

* The user name and password must be unique. Username can be up to 32 characters, and password can be up to 8 characters.

1022

* The multi language function of User permission only supported on HMI system version V2.0 or above

)))

== Settings ==

Open PIStudio software, then operate as the following figure.

1028

1029

(% style="text-align:center" %)

1030

[[image:用户权限 1.png||class="img-thumbnail"]]

1031

1032

Click on the cell from UserName and Desc, which can support the multi language.

1033

1034

(% style="text-align:center" %)

1035

[[image:UserPermissionMultilan.png]]

1036

1037

1. Click "User Permission" in "Data Tool" toolbar.

1038

1. Edit user name, click "User0" cell under "UserName", and then enter the user name, one project allows maximum 20 users.

1039

1. Edit password, click "User0" cell under "PassWord", and then enter the user name.

1040

1. Edit description, click "User0" cell under "Desc", and then enter, description is not necessary。

1041

1. Check the groups for each user, there are 11 groups beside admin.

1042

1. Editing groups' description, but it is not necessary.

1043

1. {{id name="OLE_LINK7"/}}{{id name="OLE_LINK6"/}}Click "Save and Exit" button to complete all settings.

1044

1045

(% class="box infomessage" %)

(((

✎**Note:**

* Only a maximum of one administrator permission is allowed in a profile with one user permission. If you want to use "Funtion address" to modify the user permission, you must log in the administrator account to operate.

1050

* When the configured file does not have the administrator account, a new user can be added through "Funtion address" and set as the administrator.

1051

* If you select hidden fucntion when configuring user account, the account would display as "~*~*~*~*~*~*" in the list. You only need to enter the password of the corresponding hidden user to log in.

1052

* (((

1053

Adding new UserName and Desc on the HMI by special addresses in the current language of the HMI, other languages will also configure the user names and user descriptions to the current language by default, i.e. switching to other languages, the new user names and user descriptions will not change with the language.

)))

)))

(((

)))

== Object permission configuration ==

1062

1063

(% style="text-align:center" %)

1064

[[image:用户权限 2.png||class="img-thumbnail"]]

1065

1066

User operation logs support multi languages configuration. Click on the Log Message, the text editor of multi language will be pop up:

1067

1068

(% style="text-align:center" %)

1069

[[image:LogMessagesMultilan.png]]

1070

1071

**Operation Procedure of Object Permission**

1072

1073

1. Open the object setting windows;

1074

1. Select "Security" windows;

1075

1. Check the "User Permission";

1076

1. Select "Level" to set permission level;

1077

1. Enter "Log Message", it is for operation records, if it was empty, the operation for this object would be not be recorded;

1078

1. Select the "Access Denied Setting" mode;

1079

1080

**Log information description**

1081

1082

A combination of Chinese characters, numbers, and uppercase and lowercase letters can be entered, and the number does not exceed 63.

1083

1084

The format of insert variable:{variable address, data format}. e.g., {HDW100,UW2.1}.

1085

1086

The data format are as follows.

1087

1088

(% class="table-bordered" %)

|=Letter|=Meaning

|B|Binary

|O|Octonary

|U|Unsigned decimal

|H|Hexadecimal

|b|BCD

|F|32-bit float

|S|Signed decimal

|C|Character

|W|Single word

|D|Double word

Examples.

* Unsigned decimal, BCD, 32-bit float and Signed decimal are as follows.

1104

1105

{HDW100,UW2.1}: Indicates the variable address is HDW100. The data format are: unsigned decimal, single word, two integer bits, one decimal place.

1106

1107

* (((

1108

Binary, Octonary and Hexadecimal are as follows.

1109

)))

1110

1111

{HDW100,HD8}: Indicates the variable address is HDW100. The data format are: hexadecimal, double word, eight integer bits.

1112

1113

* (((

1114

Character is as follows.

1115

)))

1116

1117

{HDW100,C32}: Indicates the variable address is HDW100. The data format are: 32 characters.

1118

1119

When a record is generated, the contents of this variable are replaced by the value of your corresponding address.

1120

1121

== **Function address** ==

1122

1123

A user must first log in before performing an operation, and after the login is successful, the user can perform the required operation, and log out after completing the operation, making the operation permission invalid. User login, log out, modification of user password during operation and user management and other functions need to be configured.

1124

1125

HMI allows managing user accounts on screen. Including adding, deleting and editing the user account. HMI provide built-in screen for [Sign in] and [change password] (screen No. 1006 and 1007).

1126

1127

Functions and addresses are as follows.

1128

1129

(% class="table-bordered" %)

1130

|=**Function**|=**Address**|=**Object type**|=**Address function**

1131

|(% rowspan="3" %)Sign in|HUW1158~~1335|Drop down list|User name

1132

|HUW1002|Character input object|Password

1133

|HUW1000|Word Switch (Input 1)|OK (sign in)

1134

|(% rowspan="5" %)Change password|HUW1158~~1335|Drop down list|User name

1135

|HUW1002|Character input object|Old password

1136

|HUW1006|Character input object|New password

1137

|HUW1010|Character input object|Confirm password

1138

|HUW1000|Word Switch (Input 2)|OK(change password)

1139

|Sign out|HUW1000|Word Switch (Input 3) |Sign out

1140

|(% rowspan="7" %)(((

1141

New user ***1**

1142

)))|HUW1014|Character input object|User name

1143

|HUW1006|Character input object|password

1144

|HUW1010|Character input object|Confirm password

1145

|HUW1000|Word Switch (Input 4) |OK(add new user)

1146

|HUW1336~~1345|Character input object|User description

1147

|HUX1347.0|Bit switch|(((

1148

~=1: User hidden

1149

1150

~=0: Visible (Defaults)

1151

)))

1152

|HUW1000|Word Switch (Input 8) |Save(add Hide features)

1153

|(% rowspan="2" %)(((

1154

Delete user ***2**

1155

)))|HUW1158~~1335|Drop down list|User name

1156

|HUW1000|Word Switch (Input 5)|OK (delete user)

1157

|Delete Profile|HUW1000|Word Switch (Input 9)|OK(delete)

1158

|Export Profile|HUW1000|Word Switch (Input 10)|OK(export)

1159

|Import profile|HUW1000|Word Switch (Input 11)|OK(import)

1160

|Export log file|HUW1000|Word Switch (Input 12)|OK(export)

1161

|Delete log file|HUW1000|Word Switch (Input 13)|OK (delete)

1162

|Current user name|HUW1349|Character object|32 Word

1163

|System state information|HUW1030|Character input object|System state information

1164

|(% rowspan="3" %)Permission settings|HUW1014|Character input object|User name

1165

|HUW1348|Bit switch|(((

1166

Set the user group:

1167

1168

HUX1348.0 = 1 administrator;

1169

1170

HUX1348.1 = 1 group 0 permission;

1171

1172

HUX1348.2 = 1 group 1 permission;

1173

1174

(Total group 0 - group 10)

1175

)))

1176

|HUW1000|Word Switch (Input 6)|Add user rights (set according to HUW1348)

1177

|User login mode setting|HUW1382|Word Switch/Numeric input object|(((

1178

0: Select a user name from the drop-down list

1179

1180

1: Use character input object (address HUW1014) to log in with a user name

1181

)))

1182

1183

When the user performs a function operation, the operation result is displayed in the HUW1001.

1184

1185

(% class="table-bordered" %)

1186

|=**Value (HUW1001)**|=**Meaning**

1187

|1|Insufficient permissions.

1188

|2|Username does not exist.

1189

|3|Username already exists.

1190

|4|Wrong username or password.

1191

|5|Login successfully.

1192

|6|Passwords are inconsistent in twice time.

1193

|7|Password changed successfully.

1194

|8|User added successfully.

1195

|9|User deleted successfully.

1196

|10|Maximum number of users exceeded.

1197

|11|Admin user already exists.

1198

|12|User permission modified successfully.

1199

|13|File imported successfully.

1200

|14|File imported failed.

1201

|15|File exported successfully.

1202

|16|File exported failed.

1203

|17|Logout successfully.

1204

|18|Profile deleted successfully.

1205

|19|Log file deleted successfully.

1206

|20|Hide settings modified successfully.

1207

|21|Hide settings modified failed.

1208

|22|(((

1209

Password already occupied, please reset.

1210

1211

(For both username and password, it can not repetition)

1212

)))

1213

1214

(% class="box infomessage" %)

(((

**✎Note:**

* *1: If there is an admin user account, then the new user can no longer add one more admin, that is, one project can only have one administrator account.

1219

* *1: When adding new user, the password could not be duplicated with other users.

1220

* *2: When deleting user, it is forbidden to delete the admin user.

1221

)))

1222

1223

**User Permission Demo Download**

1224

1225

[[https:~~/~~/drive.google.com/open?id=1qOiEDvo_1H1YqpoLDpS77dGaAFm8nrGq>>url:https://drive.google.com/open?id=1qOiEDvo_1H1YqpoLDpS77dGaAFm8nrGq]]

= Message prompt =

A message box is a window used to show some prompts or warnings to users. For example, the application process a task in the process of pop-up message box, suggesting that "U disk has been detected", then the customer can carry out data dump function.

1230

1231

(% style="text-align:center" %)

1232

[[image:消息提示 2.png||class="img-thumbnail"]]

1233

1234

(% style="text-align:center" %)

1235

[[image:8.Basic Function_html_5ce2091d6f7cd732.png||height="515" width="704" class="img-thumbnail"]]

**(1) Message**

It includes system classes (u disk, SD card, and others), chart classes (alarm, data record, recipe, file list), curve classes (Trend Chart, historical XY trend Plot).

**(2) Control**

1. **Current item: **It shows selected message information.

1244

1. **Use trigger address: **When the message is triggered, the trigger address would be set ON.

**For Example:**

Trigger address is 011, during inserting a USB flash disk into HMI, and 011 would be set ON, once HMI recognizes USB flash disk, and display message.

1249

1250

1. **Show message: **Check it to display message when HMI is running. It is checked by default.

1251

1. **Show on web: **Check it to display message when remote access HMI screen, it is unchecked by default.

1252

1253

**(3) Message Content**

1254

1255

Each message has default content, but you could set different content according to the actual situation. And the same message could be displayed in 8 languages.

1256

1257

**(4) Reload Text: **It means discard changes.

**For Example**

User deletes default content or modifies default content, but he wants to give up modification back to original, just click "Reload text".

1262

1263

(% class="box infomessage" %)

(((

**✎Note:**

* If you do not want this prompt during the running of HMI, please uncheck "Show message".

1268

* "Reload text" function would be invalid after clicking "save".

1269

* These 5 special characters are not supported in the header Multi language settings: ",", "|", "<", ">", "&".

)))

== **Appendix** ==

The following pop-up message and code only available for HMI System V1.0, to indicate some system errors:

1275

1276

|=**Message code**|=**Description**|=

1277

|=10001|Failed to delete folder directory|(% rowspan="3" %)First confirm whether the U disk SD card is read-only, or if there are other abnormalities, if it cannot handle by prevouis advises, please provide the back label and background version info.

1278

|=10002|Failed to renaming file

1279

|=10003|Failed to delete file

1280

|=10004|Inconsistent data record tables|The files in the U disk SD card may be from other projects, or the same project but the number of channels in the current project is inconsistent with the record. Please consider verifying it first.

1281

|=10009|(% rowspan="4" %)

1282

LAN monitoring error|(% rowspan="4" %)Data packet loss during the monitoring process may cause this problem. Confirm the software version. The company has updated this issue. Older versions can be updated

|=10010

|=10011

|=10012

|=10015|Failed to initialize project|It is recommended to send the project back to the company for testing

1287

|=10022|U Disk Safe Exit Failed|(% rowspan="5" %)It may be in use, data is exported, or the storage location is U disk or SD card. It is best to trigger again and wait for its successful exit.

1288

|=10023|SD card safe exit failed

1289

|=10024|U disk is busy

1290

|=10025|SD card is busy

1291

|=10026|Cannot recognize the U disk/SD card

1292

|=10027|U disk/SD card cannot be read or written|(% rowspan="3" %)Detect the format of U disk/SD card. Fat32 and ntfs can be recognized normally. If the computer can use it normally and the HMI cannot recognize it, you can only consider formatting the U disk first and then try again.

1293

|=10028|U disk/SD card unknown error

1294

|=10029|U disk/SD card format error

1295

|=11000|(% rowspan="2" %)Alarm record error|(% rowspan="29" %)(((

1296

The version before Sept. 19th considers the flash problem. Please provide the back label and the backstage version info . Make sure to ask the customer to update the version first, and the customer's similar projects must be updated even if there is no problem. After the update, the flash usage should be checked and. If the flash is on a severe status, return to the company replaces the flash with a new one.

1297

1298

When the question is returned, the text behind the prompt is as complete as possible, which can help R&D to confirm the problem faster.

1299

)))

1300

|=11001

1301

|=11002|Failed to delete Alarm record in Flash

1302

|=11006|Failed to save the Alarm records to Flash

1303

|=11007|Alarm record error

1304

|=11009|(% rowspan="2" %)Data record error

1305

|=11010

1306

|=11011|Failed to save Data records to Flash

1307

|=11012|Failed to delete Data record in Flash

1308

|=11013|Data record error

1309

|=11014|Failed to transfer Data record to U disk/SD card

1310

|=11015|Failed to copy Data record to U disk/SD card

1311

|=11016|Data record error

1312

|=11017|User permission related operation error

1313

|=11018|SQL trigger monitoring error

1314

|=11019|Data record error

1315

|=11020|Historical XY graph error

1316

|=11021|Failed to save the Historical XY graph to Flash

1317

|=11022|Failed to delete the Historical XY graph in Flash

1318

|=11023|(% rowspan="5" %)

1319

\\Installment payment error

|=11024

|=11025

|=11026

|=11027

|=11028|(% rowspan="3" %)

1325

Real-time trend graph error

1326

|=11029

1327

|=11030

1328

|=11031|Failed to delete the Real-time trend graph data in the memory

1329

|=11032|Failed to save the Real-time trend graph to Flash

1330

|=11033|(% rowspan="13" %)Recipe error|(% rowspan="13" %)If it is a new project download and there is an error, first confirm the settings of the recipe, if it is abnormal after a period of use, confirm whether it is the flash problem

|=11034

|=11035

|=11036

|=11037

|=11038

|=11039

|=11040

|=11041

|=11042

|=11043

|=11044

|=11045

|=11046|(% rowspan="3" %)User permission related operation error|(% rowspan="3" %)If an error occurs when downloading a new project, first confirm the permission configuration, whether the reserved configuration is checked in the download tool, etc., if it is abnormal after a period of use, confirm whether it is a flash problem

1344

|=11047

1345

|=11048

1346

|=11049|Failed to upload operation log file via Ethernet|

1347

|=11050|(% rowspan="8" %)User permission related operation error|(% rowspan="6" %)If an error occurs when downloading a new project, first confirm the permission configuration, whether the reserved configuration is checked in the download tool, etc., if it is abnormal after a period of use, confirm whether it is a flash problem

|=11051

|=11052

|=11053

|=11054

|=11055

|=11056|(% rowspan="2" %)

1354

|=11057

1355

|=11058|Alarm record error|(% rowspan="2" %)Same as flash problem

1356

|=11062|Installment payment error

1357

|=11063|Alarm Runbar error|Mostly, the Runbar is used without config the alarm settings.

1358

|=11069|(% rowspan="3" %)Historical trend graph error|Same as flash problem

1359

|=11070|

1360

|=11071|

1361

|=11072|SQL trigger monitoring error|

1362

|=11073|Real-time trend graph error|Same as flash problem

1363

|=11075|Error getting database table file|Same as flash problem

1364

|=11076|Error getting database table file|Same as flash problem

1365

|=11077|(% rowspan="3" %)Recipe error|(% rowspan="3" %)If it is a new project download and there is an error, first confirm the settings of the recipe, if it is abnormal after a period of use, confirm whether it is the flash problem

1366

|=11078

1367

|=11079

1368

|=11080|(% rowspan="2" %)User permission related operation error|(% rowspan="2" %)Same as 11046

1369

|=11081

1370

|=11082|Drop-down list error|

1371

|=11083|The message prompt error|

1372

|=11084|(% rowspan="2" %)Alarm record error|Same as flash problem

1373

|=11085|

1374

|=11086|(% rowspan="2" %)Data record error|Same as flash problem

1375

|=11087|

1376

|=11088|(% rowspan="2" %)Alarm record error|Same as flash problem

1377

|=11089|

1378

|=11090|Installment payment error|Same as flash problem

1379

|=11091|The message prompt error|

1380

|=11092|The database table file does not exist|

1381

|=11093|Machine code error|

1382

|=11094|Import csv file error|

1383

|=30001|Flash free space is not enough to store Data records|(% rowspan="3" %)Insufficient space, whether any file is copied into the flash

1384

|=30002|Flash free space is not enough, Historical XY trend graph is not stored

1385

|=30003|Flash free space is not enough to store real-time trend graphs

1386

|=30005|System read only|(% rowspan="2" %)Same as the flash problem, if the flash is damaged, then the system must be updated

1387

|=30006|Insufficient reserved blocks

= **Cloud** =

**Introduction**

You may configure the basic settings of Cloud functions, tags, and User MQTT according to your needs. (If the device supports the Cloud function, you can use the function and configure the tags after checking the box to enable it, or upload the data to the 3rd party server.)

1394

1395

Click "Project"-"[[image:hh_B4H5OuNT87.png||height="29" width="30"]]Cloud" in the upper left corner of the software, as shown in the following figure.

1396

1397

(% style="text-align:center" %)

1398

[[image:云配置1.png||height="494" width="750" class="img-thumbnail"]]

**(1) Enable**

If the HMI supports the Cloud function, check it to enable the Cloud function, and it will collect the real-time data from HMI upload to the Cloud. The number of data collection is limited, and the specific parameters are as follows:

1403

1404

1405

|8000-R (HMI V2.0 System)|300|200|100|1000

1406

|9000-R (HMI V2.0 System)|300|200|100|1000

1407

|3000ig|100|20|50|500

1408

|8000ig|300|200|100|1000

|MD|100|20|50|500

For example:

* In 3000ig's Cloud, the monitoring tags upload to the Cloud in real time is limited to 100.

1414

* For 3000ig's Alarm, the Alarm records of word alarms and bit alarms upload to Cloud is limited to 20. (See [["Alarm">>http://docs.we-con.com.cn/wiki/pistudio/view/Helps/08.Basic%20Function/#HAlarm]] for details).

1415

* For 3000ig's Data record, the Data records upload to Cloud is limited to 50. (For details, please refer to [["Data Record">>http://docs.we-con.com.cn/wiki/pistudio/view/Helps/08.Basic%20Function/#HDataRecord]]).

1416

1417

**(2) Server Selection**

1418

1419

**Server**: China, ASEAN, and Europe.

**Password**:

1. If the HMI is not bound, this access password will be updated and downloaded into the HMI screen simultaneously.

1424

1. If the HMI is bound, this access password in the project cannot effectively change the binding password of the device, and it can only be changed through V-NET.

1425

1426

**(3) Upload Selection**:

1427

1428

To upload the data collected by HMI to the cloud or a to the third-party server, only one upload method can be selected.

1429

1430

1. **to Cloud**: All the configured tags, data records, and alarm records would be pushed to V-NET.

1431

1. **to User MQTT**: All the configured tags, data records, and alarm records would be pushed to to the third-party server, and the relevant Lua function calls please refer to "[[Cloud interface>>http://docs.we-con.com.cn/wiki/pistudio/view/Helps/10.Lua/#HCloudInterface]]".

1432

1433

After the "to User MQTT" is checked. The tags, data records, and alarms cannot be viewed on V-NET, but the device can be bound to V-NET and remote monitoring the device screen normally.

1434

1435

**4) Low Data Mode setting**

1436

1437

1. When you check the "low Data Mod" by default on new tags, the newly added tags will be enabled in Low Data Mode by default.

1438

1. The longer the refresh interval, the slower the data upload, and the more traffic data will be saved. This function is only used for the control of tags.

1439

1440

= MQTT[[image:2.png]] =

1441

1442

(% class="wikigeneratedid" %)

1443

Configurable type MQTT. Users can publish message to the MQTT server or subscribe topics from the MQTT server.

1444

1445

The supported models and series are listed in the following table:

1446

1447

(% style="margin-left:auto; margin-right:auto; width:150px" %)

|Support series

|3000ig

|8000ig

**MQTT Configuration (Common Settings/AWS IOT Settings/ALi Settings/Huawei Settings)**

1455

1456

This chapter explains how to use configurable type MQTT. Users can publish message to the MQTT server or subscribe topics from the MQTT server.

1457

1458

Click “MQTT” in “Data Tool" in the upper side bar of the software.After checking "Enable", the settings window will pop up and select different cloud services for MQTT configuration, as shown in the following figure:

1459

1460

(% style="text-align:center" %)

1461

[[image:1747021182728-276.png]]

1462

1463

**MQTT Server Settings (Common)**

**General**

(% style="text-align:center" %)

1468

[[image:3.jpg]]

1469

1470

**Description:** Enter a description or comment about the server. Maximum input length: 255 characters, cannot be empty.

1471

1472

**Cloud Service**: (Select Common)

1473

1474

① Common (Common Platform): General MQTT publish-subscribe topic mode.

1475

1476

② AWS IoT (Amazon): Using "AWS IoT" as the Broker, using Thing to transfer data and support Shadow function.

1477

1478

③ ALi (Alibaba Cloud): Using "Alibaba Cloud" as Broker.

1479

1480

④ Huawei (Huawei Cloud): Using "Huawei Cloud" as Broker.

1481

1482

**Communication protocol**: MQTTv3.1, v3.1.1 and v5 are supported.

1483

1484

**Custom Client ID length:** User can customize the length of the Client ID (optional), length range: 20 ~~128.

1485

1486

**Custom username/password length:** Customize the length of user name/password length (optional), length range: 16 ~~ 256.

1487

1488

**IP:** Set the MQTT server IP to subscribe message.

1489

1490

**Use domain name:** Support using domain name to the specify server.

1491

1492

**Domain name:** Set the domain name of the MQTT server that subscribe message. Maximum input length: 128 characters, cannot be empty, supports letters, numbers, "-", “.”. The symbol cannot be placed at the first character or last character of name.

1493

1494

**Port number:** Set the MQTT server port to subscribe message. Range: 0~~65535, cannot be empty.

1495

1496

**Client ID:** Login name. Variables can be used as login names. For example: Enter% 0 and the Client ID is the device name. (This can be set in the HMI background. If not, the default is HMI model.) **(✎Note: A Client ID can only be used for one device.)** When there is no custom Client ID length, the maximum configurable length of Client ID is 40 characters.

1497

1498

**Verification:** Choose whether to connect to the MQTT server using [User Name] and [Password].

1499

1500

**User Name:** The [User Name] connects to the MQTT server. When there is no custom username/password length, the maximum configurable length of username is 32 characters.

1501

1502

**Password:** The password for connect to the MQTT server. When there is no custom username/password length, the maximum configurable length of password is 32 characters.

1503

1504

**Timestamp:** LOCAL: Using the HMI time as the timestamp. UTC Time: Using UTC+0.

1505

1506

**Clean message cache when normal connected:** If option is enabled, when the device is disconnected, the message to be published will be cached in the cache area, and then will be published when the device is online again.

**Address**

(% style="text-align:center" %)

1512

[[image:4.jpg]]

1513

1514

**Status address: (Total length: 2 words)**

1515

1516

HDWn: Display [MQTT] connection status.

1517

1518

|Value|Description

1519

|0|Disable MQTT server connection

1520

|1|Disconnected or connecting

1521

|2|Successfully connected the MQTT server

HDWn+1: Error prompt

|Value|Description

|0|No error

|-1|General error code of wrong operation

1528

|-3|Disconnected

1529

|-4|Exceed client data concurrency

1530

|-5|Invalid UTF-8 string

1531

|-6|Null pointer parameter

1532

|-7|Topic name is truncated

1533

|-8|Wrong protocol structure body

1534

|-9|Bad QoS, acceptable range is (0, 1, 2)

1535

|-10|Try to use a non-SSL version library for SSL connection

1536

|-11|Wrong MQTT version

1537

|-14|Wrong protocol type

1538

|-15|Option is not suitable for the current request version

1539

|-16|Call MQTT version that is not applicable to request.

1540

|-17|0 length connects topics

1541

1542

**Buffer usage address: (Total length: 1 word)**

1543

1544

Unsuccessful published message will be stored in memory as cache, with a maximum 100,000 messages or 2M. Value display as unit %, and it is carried unconditionally.

1545

1546

HDWn: Display buffer usage.

1547

1548

**Control address: (Total length: 123 words; If the domain name is not enabled, it will take up 59 words)**

1549

1550

HDWn: Control the execution or stop of [MQTT Server].

|Value|Description

|0|Ready

|1|Start

|2|Stop

|3|Update

HDWn+1: IP address of the MQTT server. (✎**Note: This address is only valid when IP is used.**)

1559

1560

HDWn+5: Port number of the MQTT server.

1561

1562

HDWn+6: Client ID of the MQTT server connection.

1563

1564

HDWn+26: Authentication is enabled or not. = 0, disabled; = 1, enabled.

1565

1566

HDWn+27: User name of MQTT server connection.

1567

1568

HDWn+43: Password of MQTT server connection.

1569

1570

HDWn+59: Domain name of the MQTT server. (**✎Note: This address is only valid if the domain name is used.**)

**TLS/SSL Settings**

(% style="text-align:center" %)

1576

[[image:5.jpg]]

1577

1578

**Enable:** Enable TLS/SSL encryption. User can manually select encrypted versions of TLS 1.0, TLS 1.1, or TLS 1.2.

1579

1580

**Server authentication:**

1581

1582

Enable: Verify whether the server certificate has been certified by a Certificate Authority Certificate (CA). Server certificates are sent by the server when connection is established.

1583

1584

Import: Select CA certificate to import.

1585

1586

More: After the import is successful, clicking it will display the certificate details.

1587

1588

Reset: Reset the import information.

1589

1590

The server name must match the certificate information: Verify whether the server name or IP matches with the information in the certificate. Domain name and IP are recorded in the Subject Alternative Name from certificate.

1591

1592

**Client authentication:** The private key and client certificate are the data required for the server to authenticate the client end.

Certificate:

Import: Select certificate to import.

1597

1598

More: After the import is successful, clicking it will display the certificate details.

1599

1600

Reset: Reset the import information.

Key:

Import: Select the key to import.

1605

1606

More: After the import is successful, clicking it will display key details.

1607

1608

Reset: Reset the import information.

**System topics**

(% style="text-align:center" %)

1614

[[image:6.jpg]]

1615

1616

**Birth Topic: **The message that HMI will publish when it is connected to server.

1617

1618

**Close Topic:** The last send message before HMI actively disconnects from server connection

1619

1620

**Last Will: **Subscription of Last Will receive this message when an abnormal disconnection occurs between HMI and the server. HMI synchronizes the Last Will message to the server when it initially establishes the connection.

1621

1622

**Topic List:** A list of topics in the HMI that is sent to the server after the HMI is connected to the server.

1623

1624

**Topic:** The actual topic name of the system topic. Maximum input length: 255 characters, cannot be empty.

1625

1626

**Retain message: **The MQTT server keeps the latest message.

1627

1628

**QoS: **MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

1629

1630

QoS 0: Messages are sent only once, and delivery is not guaranteed.

1631

1632

QoS 1: Message must be delivered at least once.

1633

1634

QoS 2: Message is delivered just once.

**Content format:**

**JSON (Default):** Use default values, default values for each system topic (**The bold is represented as the current actual value**)

**Birth Topic:**

{

"d": {

"connected": true

},

"ts": " **Current time**"

}**Close Topic: **

{

"d": {

"connected": false

},

"ts": " **Current time**"

}**Last Will: **

{

"d": {

"connected": false

}

}**Topic list:**

{

"d": {

"topics": [

{

"compression": "

",

"nickname": "**Subject name**",

"topic": "**Theme**"

},

{

"compression": "**Compression type**",

1673

1674

"nickname": "**Subject nam**e",

"topic": "**Theme**"

}

]

},

"ts": "**Current time**"

1681

}

1682

1683

Messages within topics vary depending on the actual topic settings. The above is an example of two topics.

1684

1685

**JSON (Customized):** Use custom content.

1686

1687

**Choose the connection network card**

1688

1689

(% style="text-align:center" %)

1690

[[image:7.jpg]]

1691

1692

**Default:** According to the priority order of network adapters set in the HMI background to connect server.

1693

1694

**Ethernet 1: **Specify Ethernet 1 network card to connect to the server. When the system does not find Ethernet 1, connect to the server by “Default”. When system finds Ethernet 1 and binds it to connect to the server.

1695

1696

**Ethernet 2: **Specify Ethernet 2 network card to connect to the server. When the system does not find Ethernet 2, connect to the server by “Default”. When system finds Ethernet 2 and binds it to connect to the server.

1697

1698

**4G:** Specify 4G network card to connect to server. When the system does not find 4G, connect to the server by “Default”. When system finds 4G and binds it to connect to the server.

1699

1700

**Wi-Fi:** Specify Wi-Fi network card to connect to server. When the system does not find Wi-Fi, connect to the server by “Default”. When the system finds Wi-Fi and bind it to connect to the server.

**MQTT Topic**

**MQTT topic publish**

1706

1707

Select [Topic publish], click [Add], enter [Add MQTT topic publish object], and set the general settings and address. The maximum number of MQTT published topics is 255.

1708

1709

(% style="text-align:center" %)

1710

[[image:8.jpg]]

1711

1712

**General properties**

1713

1714

(% style="text-align:center" %)

1715

[[image:9.jpg]]

1716

1717

**Alias:** Set the project name of the MQTT topic. Maximum input length: 255 characters, cannot be empty.

1718

1719

**Topic:** The topic received by the MQTT server when sending message. Maximum input length: 255 characters, cannot be empty.

1720

1721

Sending mode: (AUTO/TRIGGER)

1722

1723

**① AUTO **value change mode: When any value changes, MQTT message is published.

1724

1725

a. Minimum time interval between messages: The minimum time interval can be set between messages to avoid over-publishing MQTT messages. When the interval of value change is less than the minimum time interval between messages, the message will be put in the cache. The MQTT message will not be published until the minimum interval between messages is met. Range: 0~~3600000ms.

1726

1727

b. Periodic mode: Publish MQTT message by the fixed time. Time interval: Set the time interval for periodic publishing. The range is 1~~3600s.

**② TRIGGER**

When the specified bit is triggered, the MQTT message is published. When HDX0.0 changes from OFF to ON, an MQTT message is published, and HDX0.0 is automatically set to OFF after publishing.

1732

1733

**Compression type:** Message is compressed before it is transmitted. The compressed message needs to be decompressed before the MQTT client reads it. Zilb, Gzip, or Deflate algorithm can be chosen to compress or decompress the message.

1734

1735

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

1736

1737

0: Messages are sent only once, and delivery is not guaranteed.

1738

1739

1: Message must be delivered at least once.

1740

1741

2: Message is delivered just once.

1742

1743

**Retain message: **When checked, the MQTT server keeps the latest message.

**Content format:**

Raw data: Data composed of BYTE data.

1748

1749

JSON (General): Put all data in JSON format of member "d".

1750

1751

JSON (Advanced): JSON format of flexibly customizable nested structure.

1752

1753

**Include timestamps:** This function is only supported when the content format uses [JSON (General)], and whether to include the timestamp can be decided manually.

1754

1755

**Use the top "d" symbol in the message format:**

1756

1757

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ...,

"addressName2":...,

"ts":...

}

As shown above, when unchecked, ts and address names are both key at the same level. Therefore, avoid taking the address name as ts.

**Address setting**

①Address settings when content formats use [Raw Data] and [JSON (General)].

1790

1791

(% style="text-align:center" %)

1792

[[image:10.jpg]]

1793

1794

**Add:** Establish the address source of the topic. The length of each address can be set separately.

1795

1796

**Delete:** Delete the address.

1797

1798

**Settings:** Modify the address and name.

1799

1800

(% style="text-align:center" %)

1801

[[image:11.jpg]]

1802

1803

**Included in all message sent**

1804

1805

Check the options: This topic will include this address every time it publishes a message.

1806

1807

Uncheck the options: When the sending mode is value, message is published only when the value of the address changes.

1808

1809

**Remove JSON array brackets' ['and'] ':**

1810

1811

Check the options: Remove the array symbol name when using non-array bits or characters.

1812

1813

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

1814

1815

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

1816

1817

(% style="text-align:center" %)

1818

[[image:12.jpg]]

1819

1820

The above figure is an example. If setting like above figure, the subscription side will receive the MQTT message like following format.

{

"object": {

"value": "teststring",

"value (1)": 123,

"value (2)": true,

"value (3)": "",

"value (4)": 0,

"value (5)": true

},

"array": [

10,

20,

30

],

"value (6)": " 2023-04-27T03: 53: 20.156271 "

1837

}

1838

1839

**New component:** Add a new data component. Components can have multiple data formats; each data format has its own Name and Value. The data of the component is included in braces {}.

1840

1841

**New value:** Add a new value, string, or timestamp. When it is a value or a string, it can be fixed value or read data from a specified address.

1842

1843

**Delete:** Delete the selected field.

1844

1845

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

1846

1847

**Template:** Paste the JSON text here, and the system will automatically arrange the style to conform to this JSON format, saving the time of self-definition.

1848

1849

**Preview:** Preview JSON data in an easy-to-read format.

1850

1851

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

1852

1853

**Security settings**

1854

1855

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

1856

1857

(% style="text-align:center" %)

1858

[[image:13.jpg]]

1859

1860

**MQTT topic subscription**

1861

1862

Select [Topic subscription] and click [Add] to enter general property settings and address settings. The maximum number of MQTT subscription topics is 255.

1863

1864

(% style="text-align:center" %)

1865

[[image:14.jpg]]

1866

1867

**General properties**

1868

1869

(% style="text-align:center" %)

1870

[[image:15.jpg]]

1871

1872

**Alias:** Set the project name of the MQTT topic. Maximum input length: 255 characters, cannot be empty.

1873

1874

**Topic:** Topics subscribed from the MQTT server. Maximum input length: 255 characters, cannot be empty.

1875

1876

**Compression type:** The transport compression type of a subscription topic must be the same as that of a publication topic.

1877

1878

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

1879

1880

0: Messages are sent only once, and delivery is not guaranteed.

1881

1882

1: Message must be delivered at least once.

1883

1884

2: Message is delivered just once.

**Content format:**

Raw data: There is no original data in a specific format.

1889

1890

JSON (General): JSON format of single-layer structure.

1891

1892

JSON (Advanced): JSON format of flexibly customizable nested structure.

1893

1894

**Verify timestamp:** The user can decide whether to verify the timestamp or not. When checked, it indicates that the received data timestamp must be strictly incremented before it can be updated. Otherwise, it will be judged as outdated data and not updated.

1895

1896

**Use the top "d" symbol in the message format:**

1897

1898

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ..., "addressName2":...,

"ts":...

}

Please select the appropriate settings according to the data source.

**Address settings**

①Address settings when content formats use [Raw Data] and [JSON (General)].

1929

1930

(% style="text-align:center" %)

1931

[[image:16.jpg]]

1932

1933

**Add:** Establish the address where the data is stored after the topic is subscribed, and the length of each address can be set separately.

1934

1935

**Delete:** Delete the address.

1936

1937

**Settings:** Modify the address and name.

1938

1939

(% style="text-align:center" %)

1940

[[image:17.jpg]]

1941

1942

**Remove JSON array brackets' ['and'] ':**

1943

1944

When using non-array bits or characters, array symbol can manually be removed.

1945

1946

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

1947

1948

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

1949

1950

(% style="text-align:center" %)

1951

[[image:18.jpg]]

1952

1953

**New component:** Add a new data component. There can be multiple data formats in a component, each with a name and a value. The data of the component is included in braces {}.

1954

1955

**New Array:** Add a new data array. Arrays can have multiple data formats, but only one name. The data of the component is included in brackets [].

1956

1957

**New value:** Add a new value, string, or timestamp. When it is a value or a string, it can be fixed value or read data from a specified address.

1958

1959

**Delete:** Delete the selected field.

1960

1961

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

1962

1963

**Template:** Paste the JSON text here, and the system will automatically arrange the style to conform to this JSON format, saving the time of self-definition.

1964

1965

**Preview:** Preview JSON data in an easy-to-read format.

1966

1967

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

1968

1969

**(3) Security settings**

1970

1971

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

1972

1973

(% style="text-align:center" %)

1974

[[image:19.jpg]]

1975

1976

**MQTT Server Settings (AWS IOT)**

**General**

(% style="text-align:center" %)

1981

[[image:20.jpg]]

1982

1983

**Description:** Enter a description or comment about the server. Maximum input length: 255 characters, cannot be empty.

1984

1985

**Cloud service description**: (Select AWS IOT)

1986

1987

① Common (Common Platform): General MQTT publish-subscribe topic mode.

1988

1989

② AWS IoT (Amazon): Using "AWS IoT" as the Broker, using Thing to transfer data and support Shadow function.

1990

1991

③ ALi (Alibaba Cloud): Using "Alibaba Cloud" as Broker.

1992

1993

④ Huawei (Huawei Cloud): Using "Huawei Cloud" as Broker.

1994

1995

**Communication protocol**: MQTT v3.1.1 is supported.

1996

1997

**Domain name:** Set the domain name of the MQTT server that receives message. (Obtained from the AWS IOT platform) Maximum input length: 128 characters, cannot be empty, supports letters, numbers, "-", “.”. The symbol cannot be placed at the first character or last character of name.

1998

1999

**Port number:** Set the MQTT server port to receive message. Range: 0~~65535, cannot be empty. (AWS IOT platform is generally 8883).

2000

2001

**Client ID:** Login name. Variables can be used as login names. For example: Enter %0 and the Client ID is the device name (This can be set in the HMI background. If not, the default is HMI model). **(✎Note: A Client ID can only be used on one device.)** The maximum configurable length is 40 characters.

2002

2003

**Timestamp:** LOCAL: Using the HMI time as the timestamp. UTC Time: Using UTC+0.

**Address**

(% style="text-align:center" %)

2009

[[image:21.jpg]]

2010

2011

**Status address: (Total length: 2 words)**

2012

2013

HDWn: Display [MQTT] connection status.

2014

2015

|Value|Description

2016

|0|Disable MQTT server connection

2017

|1|Disconnected or connecting

2018

|2|Successfully connected the MQTT server

HDWn+1: Error prompt

|Value|Description

|0|No error

|-1|General error code of wrong operation

2025

|-3|Disconnected

2026

|-4|Exceed client data concurrency

2027

|-5|Invalid UTF-8 string

2028

|-6|Null pointer parameter

2029

|-7|Topic name is truncated

2030

|-8|Wrong protocol structure body

2031

|-9|Wrong QOS. (0, 1, 2) is acceptable.

2032

|-10|Attempt to use a non-SSL library for SSL connection

2033

|-11|Wrong MQTT version

2034

|-14|Wrong protocol type

2035

|-15|Option is not suitable for the current request version

2036

|-16|Call MQTT version that is not applicable to request.

2037

|-17|0 length topic connection

2038

2039

**Buffer usage address:** Not available.

2040

2041

**Control address: (Total length: 90 words)**

2042

2043

HDWn: Control the execution or stop of [MQTT Server].

|Value|Description

|0|Ready

|1|Start

|2|Stop

|3|Update

HDWn+1: Reserved for use.

2052

2053

HDWn+5: Port number of the AWS IOT connection.

2054

2055

HDWn+6: Client ID of the AWS IOT connection.

2056

2057

HDWn+26: Domain name of the AWS IOT connection.

**TLS/SSL Settings**

(% style="text-align:center" %)

[[image:22.jpg]]

**Enable:**

Enabled by default. The default is TLS V1.2.

2067

2068

**Server authentication:**

2069

2070

Enabled by default: Verify whether the server certificate has been certified by a Certificate Authority Certificate (CA). Server certificates are sent by the server when connection is established.

2071

2072

Import: Select CA certificate to import.

2073

2074

More: After the import is successful, clicking it will display the certificate details.

2075

2076

Reset: Reset the import information.

2077

2078

The server name must be matched with the certificate information to verify whether the server name or IP matches the records in the certificate. Domain name and IP are recorded in the Subject Alternative Name in the certificate.

2079

2080

**(3) Client authentication:** The private key and client certificate are the data required for the server to authenticate the client end.

Certificate:

Import: Select certificate to import.

2085

2086

More: After the import is successful, clicking it will display the certificate details.

2087

2088

Reset: Reset the import information.

Key:

Import: Select the key to import.

2093

2094

More: After the import is successful, clicking it will display key details.

2095

2096

Reset: Reset the import information.

**Device setting**

Select [Add] to enter [General property settings and address settings]. To delete a device, select the device and click Delete.

2102

2103

(% style="text-align:center" %)

[[image:23.jpg]]

**General**

(% style="text-align:center" %)

2109

[[image:24.jpg]]

2110

2111

**Device name:** It is consistent with the item name on AWS IOT. Maximum input length: 128 characters, cannot be empty, supports letters, numbers, "-", "_".

2112

2113

**Description:** For distinguish purpose. Maximum input length: 255 characters.

2114

2115

**Minimum time interval between messages:** The minimum time interval can be set between messages to avoid over-publishing MQTT messages. That is, when the interval of value change is less than the minimum time interval between messages, the message will be put in the cache, and the MQTT message will not be released until the minimum time interval between messages is met. Range: 0~~3600000ms.

2116

2117

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

2118

2119

0: Messages are sent only once, and delivery is not guaranteed.

2120

2121

1: Message must be delivered at least once.

2122

2123

2: Message is delivered just once.

2124

2125

**Content format:** Not configurable. All data is in JSON format.

2126

2127

**Include timestamps:** Whether to include the timestamp can be decided manually.

2128

2129

**Use the top "d" symbol in the message format:**

2130

2131

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ...,

"addressName2":...,

"ts":...

}

As shown above, when unchecked, ts and address names are both key at the same level. Therefore, avoid taking the address name as ts.

**Address**

(% style="text-align:center" %)

2164

[[image:25.jpg]]

2165

2166

**Add:** Establish the address source of the topic. The length of each address can be set separately.

2167

2168

**Delete:** Delete the address.

2169

2170

**Settings:** Modify the address and name.

2171

2172

(% style="text-align:center" %)

[[image:26.jpg]]

**Advanced Mode:**

Check the options: Check to configure four “Settings/Status".

2178

2179

Uncheck the options: Check to configure two "Settings/Status".

2180

2181

**Name:** Correspond to the key value in JSON.

2182

2183

**Type:** “Bit" and “Word” are optional. “Word” configuration can choose system of numeration.

**Length:**

Length 1: General JSON format.

2188

2189

Length > 1: Enable the format of JSON array. The values of continuous address with the configuration address as the first address as the elements of the array. This length is valid to the selected "settings/status”. (For example, the length is set to 3, and 4 "settings/states" are checked, so the length of these 4 are all 3). Range: 1-255.

2190

2191

For example, configure as the following figure:

2192

2193

(% style="text-align:center" %)

2194

[[image:27.jpg]]

2195

2196

Then HDW0, HDW2 and HDW4 will be read and published to the reported key; HDW10, HDW12, HDW14 will be read and published to the desired key. For example, if HDW0=1, HDW2=2, HDW4=3, HDW10=4, HDW12=5, and HDW14=6, the subscribed message format is as follows.

{

"state": {

"desired": {

"welcome": [1, 2, 3]

},

"reported": {

"welcome": [4, 5, 6]

}

}

}

**Status (Device address~-~->AWS IOT "reported"):** Pass a value from the Device address to the AWS IOT “reported” in one direction, which is equivalent to publishing to "reported".

2219

2220

**Setting (Device address->AWS IOT "desired"):** Pass a value from the Device address to the AWS IOT “desired” in one direction, which is equivalent to publishing to “desired".

2221

2222

**Status (AWS IOT "reported"->Device address):** Pass a value from AWS IOT "reported" to Device address in one direction, which is equivalent to subscribing to "reported".

2223

2224

**Settings (AWS IOT "desired"->Device address):** Pass a value from the AWS IOT "desired" to the Device address in one direction, which is equivalent to subscribing to "desired".

2225

2226

**Remove JSON array brackets' ['and'] ':** Check to remove array symbols when using non-array bits or characters. (Configurable when length is 1).

2227

2228

**MQTT Server Settings (ALi)**

**General**

(% style="text-align:center" %)

2233

[[image:28.jpg]]

2234

2235

**Description:** Enter a description or comment about the server. Maximum input length: 255 characters, cannot be empty.

2236

2237

**Cloud service description**: (Select Ali)

2238

2239

① Common (Common Platform): General MQTT publish-subscribe topic mode.

2240

2241

② AWS IoT (Amazon): Using "AWS IoT" as the Broker, using Thing to transfer data and support Shadow function.

2242

2243

③ ALi (Alibaba Cloud): Using "Alibaba Cloud" as Broker.

2244

2245

④ Huawei (Huawei Cloud): Using "Huawei Cloud" as Broker.

2246

2247

**Communication protocol**: MQTTv3.1, v3.1.1 and v5 are supported.

2248

2249

**Domain name:** Set the domain name of the MQTT server that receives message. Maximum input length: 128 characters, cannot be empty, supports letters, numbers, "-", “.”. The symbol cannot be placed at the first character or last character of name.

2250

2251

**Port number:** Set the MQTT server port to subscribe message. Range: 0~~65535, cannot be empty.

2252

2253

**Client ID:** Login name. Variables can be used as login names. For example: Enter %0 and the Client ID is the device name (This can be set in the HMI background. If not, the default is HMI model). (Note: A Client ID can only be used for one device.) When there is no custom Client ID length, the maximum configurable length of a Client ID is 64 characters.

2254

2255

**ProductId:** The key of the product to which the device belongs, that is, the globally unique identifier issued by the IoT platform for the product. (Obtained from Alibaba Cloud Platform) Maximum input length: 128 characters.

2256

2257

**DeviceId:** Unique identifier of the device within the product. DeviceName is combined with ProductKey of the product to which the device belongs as the device identification, which is used for connection authentication and communication with the IoT platform. (Obtained from Alibaba Cloud Platform) Maximum input length: 64 characters.

2258

2259

**DeviceSecret:** The device key issued by the IoT platform for devices is used for authentication and encryption. It needs to be used in pairs with DeviceName. (Obtained from Alibaba Cloud Platform) Maximum input length: 128 characters.

2260

2261

**Encryption algorithm:** Alibaba Cloud's signature algorithm type supports hmacmd5 and hmacsha1.

2262

2263

**Timestamp:** LOCAL: Using the HMI time as the timestamp. UTC Time: Use UTC+0 time.

2264

2265

**Clean message cache when normal connected:** If option is enabled, when the device is disconnected, the message to be published will be cached in the cache area, and then will be published when the device is online again.

**Address**

(% style="text-align:center" %)

2271

[[image:29.jpg]]

2272

2273

**Status address: (Total length: 2 words)**

2274

2275

HDWn: Display [MQTT] connection status.

2276

2277

|Value|Description

2278

|0|Disable MQTT server connection

2279

|1|Disconnected or connecting

2280

|2|Successfully connected the MQTT server

HDWn+1: Error prompt

|Value|Description

|0|No error

|-1|General error code of wrong operation

2287

|-3|Disconnected

2288

|-4|Exceed client data concurrency

2289

|-5|Invalid UTF-8 string

2290

|-6|Null pointer parameter

2291

|-7|Topic name is truncated

2292

|-8|Wrong protocol structure body

2293

|-9|Wrong QOS. (0, 1, 2) is acceptable.

2294

|-10|Attempt to use a non-SSL library for SSL connection

2295

|-11|Wrong MQTT version

2296

|-14|Wrong protocol type

2297

|-15|Option is not suitable for the current request version

2298

|-16|Call MQTT version that is not applicable to request.

2299

|-17|0 length topic connection

2300

2301

**Buffer usage address: (Total length: 1 word)**

2302

2303

Unsuccessful published message will be stored in memory as cache, with a maximum 100,000 messages or 2M. Value display as unit %, and it is carried unconditionally.

2304

2305

HDWn: Display buffer usage.

2306

2307

**Control address: (Total length: 258 words)**

2308

2309

HDWn: Control the execution or stop of [MQTT Server].

|Value|Description

|0|Ready

|1|Start

|2|Stop

|3|Update

HDWn+1: Port number of the Alibaba Cloud connection.

2318

2319

HDWn+2: Domain name title of the Alibaba Cloud connection.

2320

2321

HDWn+66: Client ID of the Alibaba Cloud connection.

2322

2323

HDWn+98: ProductId of the Alibaba Cloud connection.

2324

2325

HDWn+162: DeviceId of the Alibaba Cloud connection.

2326

2327

HDWn+194: DeviceSecret of the Alibaba Cloud connection.

**TLS/SSL Settings**

(% style="text-align:center" %)

2332

[[image:30.jpg]]

2333

2334

**Enable:** Enable TLS/SSL encryption. User can manually select encrypted versions of TLS 1.0, TLS 1.1, or TLS 1.2.

2335

2336

**Server authentication:**

2337

2338

Enable: Verify whether the server certificate has been certified by a Certificate Authority Certificate (CA). Server certificates are sent by the server when connection is established.

2339

2340

Import: Select CA certificate to import.

2341

2342

More: After the import is successful, clicking it will display the certificate details.

2343

2344

Reset: Reset the import information.

2345

2346

The server name must be matched with the certificate information to verify whether the server name or IP matches the records in the certificate. Domain name and IP are recorded in the Subject Alternative Name in the certificate.

2347

2348

**(3) Client authentication:** The private key and client certificate are the data required for the server to authenticate the client end.

Certificate:

Import: Select certificate to import.

2353

2354

More: After the import is successful, clicking it will display the certificate details.

2355

2356

Reset: Reset the import information.

Key:

Import: Select the key to import.

2361

2362

More: After the import is successful, clicking it will display key details.

2363

2364

Reset: Reset the import information.

**MQTT Topic**

(% class="wikigeneratedid" id="H1.MQTTtopicpublish" %)

2370

**MQTT topic publish**

2371

2372

Select [Topic publish], click [Add], enter [Add MQTT topic publish object], and set the general settings and address. The maximum number of MQTT published topics is 255.

2373

2374

(% style="text-align:center" %)

2375

[[image:31.jpg]]

2376

2377

**General properties**

2378

2379

(% style="text-align:center" %)

[[image:32.jpg]]

**Alias:** Set the project name of the MQTT theme. Maximum input length: 255 characters, cannot be empty.

2384

2385

**Topic:** The topic received by the MQTT server when sending message. Maximum input length: 255 characters, cannot be empty.

2386

2387

**Sending mode:** **(AUTO/TRIGGER)**

2388

2389

**① AUTO **value change mode: When any value changes, MQTT message is published.

2390

2391

a. Minimum time interval between messages: The minimum time interval can be set between messages to avoid over-publishing MQTT messages. When the interval of value change is less than the minimum time interval between messages, the message will be put in the cache. The MQTT message will not be published until the minimum interval between messages is met. Range: 0~~3600000ms.

2392

2393

b. Periodic mode: Publish MQTT message by the fixed time. Time interval: Set the time interval for periodic publishing, ranging from 1 to 3600s.

**② TRIGGER**

When the specified bit is triggered, the MQTT message is published. When HDX0.0 changes from OFF to ON, an MQTT message is published, and HDX0.0 is automatically set to OFF after publishing.

2398

2399

**Compression type:** Message is compressed before it is transmitted. The compressed message needs to be decompressed before the MQTT client reads it. Zlib, Gzip, or Deflate algorithm can be chosen to compress or decompress the message.

2400

2401

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

2402

2403

0: Messages are sent only once, and delivery is not guaranteed.

2404

2405

1: Message must be delivered at least once.

2406

2407

2: Message is delivered just once.

2408

2409

**Retain message:** When checked, the MQTT server will keep the latest message.

**Content format:**

Raw data: Data composed of BYTE data.

2414

2415

JSON (General): Put all data in JSON format of member "d".

2416

2417

JSON (Advanced): JSON format of flexibly customizable nested structure.

2418

2419

**Include timestamps:** This function is only supported when the content format uses [JSON (General)], and whether to include the timestamp can be decided manually.

2420

2421

**Use the top "d" symbol in the message format:**

2422

2423

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ...,

"addressName2":...,

"ts":...

}

As shown above, when unchecked, ts and address names are both key at the same level. Therefore, avoid taking the address name as ts.

**Address setting**

①Address settings when content formats use [Raw Data] and [JSON (General)].

2457

2458

(% style="text-align:center" %)

2459

[[image:33.jpg]]

2460

2461

**Add:** Establish the address source of the topic. The length of each address can be set separately.

2462

2463

**Delete:** Delete the address.

2464

2465

**Settings:** Modify the address and name.

2466

2467

(% style="text-align:center" %)

2468

[[image:34.jpg]]

2469

2470

**Included in all message sent**

2471

2472

Check the options: This topic will include this address every time it publishes a message.

2473

2474

Uncheck the options: When the sending mode is value, message is published only when the value of the address changes.

2475

2476

**Remove JSON array brackets' ['and'] ':**

2477

2478

Check the options: Remove the array symbol name when using non-array bits or characters.

2479

2480

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

2481

2482

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

2483

2484

(% style="text-align:center" %)

2485

[[image:HMIEditor_Db5tLtioq7.jpg]]

2486

2487

The above figure is an example. If setting like above figure, the subscription side will receive the MQTT message like following format.

{

"object": {

"value": "teststring",

"value (1)": 123,

"value (2)": true,

"value (3)": "",

"value (4)": 0,

"value (5)": true

},

"array": [

10,

20,

30

],

"value (6)": " 2023-04-27T03: 53: 20.156271 "

2504

}

2505

2506

**New component:** Add a new data component. Components can have multiple data formats; each data format has its own Name and Value. The data of the component is included in braces {}.

2507

2508

**New value:** Add a value, string, or timestamp. When it is a value or a string, data can be read for a fixed value or from a specified address.

2509

2510

**Delete:** Delete the selected field.

2511

2512

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

2513

2514

**Template:** Paste the JSON text, and the system will automatically arrange the schema to conform to this JSON format, saving the time of self-definition.

2515

2516

**Preview:** Preview JSON data in an easy-to-read format.

2517

2518

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

2519

2520

2521

**Security settings**

2522

2523

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

2524

2525

(% style="text-align:center" %)

2526

[[image:35.jpg]]

2527

2528

**MQTT topic subscription**

2529

2530

Select [Topic subscription] and click [Add] to enter general property settings and address settings. The maximum number of MQTT subscription topics is 255.

2531

2532

(% style="text-align:center" %)

2533

[[image:36.jpg]]

2534

2535

**General properties**

2536

2537

(% style="text-align:center" %)

2538

[[image:37.jpg]]

2539

2540

**Alias:** Set the project name of the MQTT theme. Maximum input length: 255 characters, cannot be empty.

2541

2542

**Topic:** Topics subscribed from the MQTT server. Maximum input length: 255 characters, cannot be empty.

2543

2544

**Compression type:** The transport compression type of a subscription topic must be the same as that of a publication topic.

2545

2546

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

2547

2548

0: Messages are sent only once, and delivery is not guaranteed.

2549

2550

1: Message must be delivered at least once.

2551

2552

2: Message is delivered just once.

**Content format:**

Raw data: There is no original data in a specific format.

2557

2558

JSON (General): JSON format of single-layer structure.

2559

2560

JSON (Advanced): JSON format of flexibly customizable nested structure.

2561

2562

**Verify timestamp:** The user can decide whether to verify the timestamp or not. When checked, it indicates that the received data timestamp must be strictly incremented before it can be updated. Otherwise, it will be judged as outdated data and not updated.

2563

2564

**Use the top "d" symbol in the message format:**

2565

2566

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ..., "addressName2":...,

"ts":...

}

Please select the appropriate settings according to the data source.

**Address setting**

①Address settings when content formats use [Raw Data] and [JSON (General)].

2597

2598

(% style="text-align:center" %)

2599

[[image:38.jpg]]

2600

2601

**Add:** Establish the address where the data is placed after the topic is subscribed, and the length of each address can be set separately.

2602

2603

**Delete:** Delete the address.

2604

2605

**Settings:** Modify the address and name.

2606

2607

(% style="text-align:center" %)

2608

[[image:39.jpg]]

2609

2610

**Remove JSON array brackets' ['and'] ':**

2611

2612

When using non-array bits or characters, array symbol can manually be removed.

2613

2614

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

2615

2616

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

2617

2618

(% style="text-align:center" %)

2619

[[image:40.jpg]]

2620

2621

**New component:** Add a new data component. There can be multiple data formats in a component, each with a name and a value. The data of the component is included in braces {}.

2622

2623

**New Array:** Add a new data array. Arrays can have multiple data formats, but only one name. The data of the component is included in brackets [].

2624

2625

**New value:** Add a value, string, or timestamp. When it is a value or a string, data can be read for a fixed value or from a specified address.

2626

2627

**Delete:** Delete the selected field.

2628

2629

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

2630

2631

**Template:** Paste the JSON text, and the system will automatically arrange the schema to conform to this JSON format, saving the time of self-definition.

2632

2633

**Preview:** Preview JSON data in an easy-to-read format.

2634

2635

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

2636

2637

2638

**Security settings**

2639

2640

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

2641

2642

(% style="text-align:center" %)

2643

[[image:41.jpg]]

2644

2645

**MQTT Server Settings (Huawei)**

**General**

(% style="text-align:center" %)

2650

[[image:42.jpg]]

2651

2652

**Description:** Enter a description or comment about the server. Maximum input length: 255 characters, cannot be empty.

2653

2654

**Cloud service description**: (Select Huawei)

2655

2656

① Common (Common Platform): General MQTT publish-subscribe topic mode.

2657

2658

② AWS IoT (Amazon): Using "AWS IoT" as the Broker, using Thing to transfer data and support Shadow function.

2659

2660

③ ALi (Alibaba Cloud): Using "Alibaba Cloud" as Broker.

2661

2662

④ Huawei (Huawei Cloud): Using "Huawei Cloud" as Broker.

2663

2664

**Communication protocol**: MQTTv3.1, v3.1.1 and v5 are supported.

2665

2666

**Domain name:** Set the domain name of the MQTT server that subscribe message. Maximum input length: 128 characters, cannot be empty, supports letters, numbers, "-", “.”. The symbol cannot be placed at the first character or last character of name.

2667

2668

**Port number:** Set the MQTT server port to subscribe message. Range: 0~~65535, cannot be empty.

2669

2670

**DeviceId:** **Device ID** generated when registering the device in Huawei Cloud. Maximum input length: 128 characters

2671

2672

**DeviceSecret:** Customized **password **when registering devices on Huawei Cloud Maximum input length: 128 characters.

2673

2674

**Timestamp:** LOCAL: Using the HMI time as the timestamp. UTC Time: Using UTC+0.

2675

2676

**Clean message cache when normal connected:** If option is enabled, when the device is disconnected, the message to be published will be cached in the cache area, and then will be published when the device is online again.

**Address**

(% style="text-align:center" %)

2682

[[image:43.jpg]]

2683

2684

**Status address: (Total length: 2 words)**

2685

2686

HDWn: Display [MQTT] connection status.

2687

2688

|Value|Description

2689

|0|Disable MQTT server connection

2690

|1|Disconnected or connecting

2691

|2|Successfully connected the MQTT server

HDWn+1: Error prompt

|Value|Description

|0|No error

|-1|General error code of wrong operation

2698

|-3|Disconnected

2699

|-4|Exceed client data concurrency

2700

|-5|Invalid UTF-8 string

2701

|-6|Null pointer parameter

2702

|-7|Topic name is truncated

2703

|-8|Wrong protocol structure body

2704

|-9|Wrong QOS. (0, 1, 2) is acceptable.

2705

|-10|Attempt to use a non-SSL library for SSL connection

2706

|-11|Wrong MQTT version

2707

|-14|Wrong protocol type

2708

|-15|Option is not suitable for the current request version

2709

|-16|Call MQTT version that is not applicable to request.

2710

|-17|0 length topic connection

2711

2712

**Buffer usage address: (Total length: 1 word)**

2713

2714

Unsuccessful published message will be stored in memory as cache, with a maximum 100,000 messages or 2M. Value display as unit %, and it is carried unconditionally.

2715

2716

HDWn: Display buffer usage.

2717

2718

**Control address: (Total length: 194 words)**

2719

2720

HDWn: Control the execution or stop of [MQTT Server].

|Value|Description

|0|Ready

|1|Start

|2|Stop

|3|Update

HDWn+1: Port number of the Huawei Cloud.

2729

2730

HDWn+2: Domain name of the Huawei Cloud.

2731

2732

HDWn+66: DeviceSecret of the Huawei Cloud.

2733

2734

HDWn+130: DeviceSecret of the Huawei Cloud.

**TLS/SSL Settings**

(% style="text-align:center" %)

2739

[[image:44.jpg]]

2740

2741

**Enable:** Enable TLS/SSL encryption. User can manually select encrypted versions of TLS 1.0, TLS 1.1, or TLS 1.2.

2742

2743

**Server authentication:**

2744

2745

Enable: Verify whether the server certificate has been certified by a Certificate Authority Certificate (CA). Server certificates are sent by the server when connection is established.

2746

2747

Import: Select CA certificate to import.

2748

2749

More: After the import is successful, clicking it will display the certificate details.

2750

2751

Reset: Reset the import information.

2752

2753

The server name must match the certificate information: Verify whether the server name or IP matches with the information in the certificate. Domain name and IP are recorded in the Subject Alternative Name from certificate.

2754

2755

**Client authentication:** The private key and client certificate are the data required for the server to authenticate the client end.

Certificate:

Import: Select certificate to import.

2760

2761

More: After the import is successful, clicking it will display the certificate details.

2762

2763

Reset: Reset the import information.

Key:

Import: Select the key to import.

2768

2769

More: After the import is successful, clicking it will display key details.

2770

2771

Reset: Reset the import information.

**MQTT Topic**

**MQTT topic publish**

2776

2777

Select [Topic publish], click [Add], enter [Add MQTT topic publish object], and set the general settings and address. The maximum number of MQTT published topics is 255.

2778

2779

(% style="text-align:center" %)

2780

[[image:45.jpg]]

2781

2782

**General properties**

2783

2784

(% style="text-align:center" %)

2785

[[image:46.jpg]]

2786

2787

**Alias:** Set the project name of the MQTT theme. Maximum input length: 255 characters, cannot be empty.

2788

2789

**Topic:** The topic received by the MQTT server when sending message. Maximum input length: 255 characters, cannot be empty.

2790

2791

**Sending mode:** **(AUTO/TRIGGER)**

2792

2793

**① AUTO **value change mode: When any value changes, MQTT message is published.

2794

2795

a. Minimum time interval between messages: The minimum time interval can be set between messages to avoid over-publishing MQTT messages. When the interval of value change is less than the minimum time interval between messages, the message will be put in the cache. The MQTT message will not be published until the minimum interval between messages is met. Range: 0~~3600000ms.

2796

2797

b. Periodic mode: Publish MQTT message by the fixed time. Time interval: Set the time interval for periodic publishing, ranging from 1 to 3600s.

**② TRIGGER**

When the specified bit is triggered, the MQTT message is published. When HDX0.0 changes from OFF to ON, an MQTT message is published, and HDX0.0 is automatically set to OFF after publishing.

2802

2803

**Compression type:** Message is compressed before it is transmitted. The compressed message needs to be decompressed before the MQTT client reads it. Zlib, Gzip, or Deflate algorithm can be chosen to compress or decompress the message.

2804

2805

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

2806

2807

0: Messages are sent only once, and delivery is not guaranteed.

2808

2809

1: Message must be delivered at least once.

2810

2811

2: Message is delivered just once.

2812

2813

**Retain message:** When checked, the MQTT server will keep the latest message.

**Content format:**

Raw data: Data composed of BYTE data.

2818

2819

JSON (General): Put all data in JSON format of member "d".

2820

2821

JSON (Advanced): JSON format of flexibly customizable nested structure.

2822

2823

**Include timestamps:** This function is only supported when the content format uses [JSON (General)], and whether to include the timestamp can be decided manually.

2824

2825

**Use the top "d" symbol in the message format:**

2826

2827

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ...,

"addressName2":...,

"ts":...

}

As shown above, when unchecked, ts and address names are both key at the same level. Therefore, avoid taking the address name as ts.

**Address setting**

①Address settings when content formats use [Raw Data] and [JSON (General)].

2861

2862

(% style="text-align:center" %)

2863

[[image:47.jpg]]

2864

2865

**Add:** Establish the address source of the topic. The length of each address can be set separately.

2866

2867

**Delete:** Delete the address.

2868

2869

**Settings:** Modify the address and name.

2870

2871

(% style="text-align:center" %)

2872

[[image:48.jpg]]

2873

2874

**Included in all message sent**

2875

2876

Check the options: This topic will include this address every time it publishes a message.

2877

2878

Uncheck the options: When the sending mode is value, message is published only when the value of the address changes.

2879

2880

**Remove JSON array brackets' ['and'] ':**

2881

2882

Check the options: Remove the array symbol name when using non-array bits or characters.

2883

2884

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

2885

2886

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

2887

2888

(% style="text-align:center" %)

2889

[[image:49.jpg]]

2890

2891

The above figure is an example. If setting like above figure, the subscription side will receive the MQTT message like following format.

{

"object": {

"value": "teststring",

"value (1)": 123,

"value (2)": true,

"value (3)": "",

"value (4)": 0,

"value (5)": true

},

"array": [

10,

20,

30

],

"value (6)": " 2023-04-27T03: 53: 20.156271 "

2908

}

2909

2910

**New component:** Add a new data component. Components can have multiple data formats; each data format has its own Name and Value. The data of the component is included in braces {}.

2911

2912

**New value:** Add a value, string, or timestamp. When it is a value or a string, data can be read for a fixed value or from a specified address.

2913

2914

**Delete:** Delete the selected field.

2915

2916

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

2917

2918

**Template:** Paste the JSON text, and the system will automatically arrange the schema to conform to this JSON format, saving the time of self-definition.

2919

2920

**Preview:** Preview JSON data in an easy-to-read format.

2921

2922

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

2923

2924

2925

**Security settings**

2926

2927

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

2928

2929

(% style="text-align:center" %)

[[image:50.jpg]]

**MQTT topic subscription**

2934

2935

Select [Topic subscription] and click [Add] to enter general property settings and address settings. The maximum number of MQTT subscription topics is 255.

2936

2937

(% style="text-align:center" %)

2938

[[image:51.jpg]]

2939

2940

**General properties**

2941

2942

(% style="text-align:center" %)

2943

[[image:52.jpg]]

2944

2945

**Alias:** Set the project name of the MQTT theme. Maximum input length: 255 characters, cannot be empty.

2946

2947

**Topic:** Topics subscribed from the MQTT server. Maximum input length: 255 characters, cannot be empty.

2948

2949

**Compression type:** The transport compression type of a subscription topic must be the same as that of a publication topic.

2950

2951

**QoS:** MQTT provides three levels of reliability called service quality. The service quality of message transmission determines whether the message is guaranteed to be delivered.

2952

2953

0: Messages are sent only once, and delivery is not guaranteed.

2954

2955

1: Message must be delivered at least once.

2956

2957

2: Message is delivered just once.

**Content format:**

Raw data: There is no original data in a specific format.

2962

2963

JSON (General): JSON format of single-layer structure.

2964

2965

JSON (Advanced): JSON format of flexibly customizable nested structure.

2966

2967

**Verify timestamp:** The user can decide whether to verify the timestamp or not. When checked, it indicates that the received data timestamp must be strictly incremented before it can be updated. Otherwise, it will be judged as outdated data and not updated.

2968

2969

**Use the top "d" symbol in the message format:**

2970

2971

This function is only supported when the content format uses [JSON (General)]. When checked, the message format is as follows:

{

"d": {

"addressName1": ...,

"addressName2":...

},

"ts":...

}

When unchecked, the message format is as follows:

{

"addressName1": ..., "addressName2":...,

"ts":...

}

Please select the appropriate settings according to the data source.

**Address setting**

①Address settings when content formats use [Raw Data] and [JSON (General)].

3002

3003

(% style="text-align:center" %)

3004

[[image:53.jpg]]

3005

3006

**Add:** Establish the address where the data is placed after the topic is subscribed. The length of each address can be set separately.

3007

3008

**Delete:** Delete the address.

3009

3010

**Settings:** Modify the address and name.

3011

3012

(% style="text-align:center" %)

3013

[[image:54.jpg]]

3014

3015

**Remove JSON array brackets' ['and'] ':**

3016

3017

When using non-array bits or characters, array symbol can manually be removed.

3018

3019

**✎Note: A topic can be configured up to 255 nodes. The name length of a node can be configured up to a maximum of 255 characters and cannot be empty.**

3020

3021

② Address setting when the content format uses [JSON (Advanced)]. [JSON (Advanced)] supports nested structure, which can use components, arrays and other forms. Timestamps and data names can also be customized, which is a more flexible design method.

3022

3023

(% style="text-align:center" %)

3024

[[image:HMIEditor_Db5tLtioq7.jpg]]

3025

3026

**New component:** Add a new data component. There can be multiple data formats in a component, each with a name and a value. The data of the component is included in braces {}.

3027

3028

**New Array:** Add a new data array. Arrays can have multiple data formats, but only one name. The data of the component is included in brackets [].

3029

3030

**New value:** Add a value, string, or timestamp. When it is a value or a string, data can be read for a fixed value or from a specified address.

3031

3032

**Delete:** Delete the selected field.

3033

3034

**Settings:** Modify the selected field. If the selected fields are components and arrays, only the names can be modified. But components and arrays include values that can modify parameters.

3035

3036

**Template:** Paste the JSON text, and the system will automatically arrange the schema to conform to this JSON format, saving the time of self-definition.

3037

3038

**Preview:** Preview JSON data in an easy-to-read format.

3039

3040

**✎Note: A Topic can be up to 512 nodes (including payload), and a node name can be configured to be up to 255 characters length.**

3041

3042

3043

**Security settings**

3044

3045

The topic is published only when the register status matches the setting. As shown in the following figure, this topic will not be published until the address HDX0.0 is set to ON.

3046

3047

(% style="text-align:center" %)

[[image:56.jpg]]

= OPCUA Server =

(% class="box infomessage" %)

3053

(((

3054

✎Note: Only 8000ig Series support OPC UA Server.

3055

)))

3056

3057

1.Open the OPCUA server tool

3058

3059

[Project]→[OPCUA server]→[Enable]

3060

3061

(% style="text-align:center" %)

3062

[[image:QOBzq5f8HF.png]]

3063

3064

2.Set General properties

3065

3066

(% style="text-align:center" %)

3067

[[image:e9rHcIHKsj.png]]

3068

3069

**Description:**Description of OPCUA server, character length 0~~255.** **

3070

3071

**OPC TCP:**Set URL of OPCUA server.

3072

3073

**Port number:**The port used by the client for communication.Default: 4840.

3074

3075

**Server name:**Set the name of Server,character length 0~~255.

3076

3077

**Security:**OPCUA server provides four security policies and three authentication methods, and different encryption methods can be implemented through different combinations.

3078

3079

3.User authentication

3080

3081

(% style="text-align:center" %)

3082

[[image:1733132656389-393.png]]

3083

3084

**Anonymous:**When the client chooses to log in anonymously, the permissions to interact with the server include brows, read and write.

3085

3086

**User name password:**The user name and password here are equivalent to the user name and password set on the [Project Settiing\User Login] page. When the client logs in to the server by using the user name and password, the user password used has the same group level as that configured by the server and has corresponding permissions.

4.Main interface

(% style="text-align:center" %)

3091

[[image:1733133255552-776.png]]

3092

3093

**Enable:**Check to configure the relevant properties of the OPC UA server

3094