Skip to Content

Changes for page 12 PLC Protocol OLD

Last modified by Mora Zhou on 2024/12/05 14:53
From version 16.1
edited by Ben
on 2022/08/11 14:06
Change comment: There is no comment for this version
To version 13.1
edited by Ben
on 2022/08/11 10:33
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -2478,7 +2478,7 @@
2478 2478  **✎Note:** COM3 only available in PI8000/PI9000 series.
2479 2479  
2480 2480  
2481 -== **1 HMI and Wecon LX5V serial communication** ==
2481 +== **2 Communication with Wecon LX5V** ==
2482 2482  
2483 2483  This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2484 2484  
... ... @@ -2540,88 +2540,11 @@
2540 2540  
2541 2541  Parity：No verification
2542 2542  
2543 +[[image:image-20220811093202-2.png]]
2543 2543  
2544 -[[image:image-20220811104012-1.png]]
2545 2545  
2546 2546  
2547 -**hardware connection**
2548 2548  
2549 -**1）Hardware wiring diagram**
2550 -
2551 -This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
2552 -
2553 -[[image:image-20220811103005-4.png]]
2554 -
2555 -
2556 -[[image:image-20220811103227-7.png]]
2557 -
2558 -The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
2559 -
2560 -
2561 -== **2 HMI and Wecon LX5V-N Ethernet communication** ==
2562 -
2563 -(% id="cke_bm_147709S" style="display:none" %) (%%)This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2564 -
2565 -
2566 -**Software configuration of PLC**
2567 -
2568 -**1）PLC programming software**
2569 -
2570 -[[image:image-20220810164710-1.png]]
2571 -
2572 -**2）New PLC project**
2573 -
2574 -Click New Project and select the PLC model.
2575 -
2576 -[[image:image-20220811115454-1.png]]
2577 -
2578 -
2579 -**3）Set Ethernet port parameters**
2580 -
2581 -Follow the steps below to configure Serial port parameters
2582 -
2583 -PLC IP address：192.168.39.200
2584 -
2585 -default gateway：192.168.39.1
2586 -
2587 -subnet mask：255.255.255.0
2588 -
2589 -[[image:image-20220811140530-2.png]]
2590 -
2591 -
2592 -**4）Registers list**
2593 -
2594 -[[image:image-20220811102219-3.png]]
2595 -
2596 -
2597 -**HMI software configuration**
2598 -
2599 -**1）HMI programming software**
2600 -
2601 - [[image:image-20220810171237-4.png]]
2602 -
2603 -**2）New HMI project**
2604 -
2605 -Click New Project and select the HMI model.
2606 -
2607 -[[image:image-20220810172010-5.png]]
2608 -
2609 -**3）Set communication port parameters**
2610 -
2611 -Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
2612 -
2613 -Baud rate：115200
2614 -
2615 -Data bit：8
2616 -
2617 -Stop bit：1
2618 -
2619 -Parity：No verification
2620 -
2621 -
2622 -[[image:image-20220811104012-1.png]]
2623 -
2624 -
2625 2625  **hardware connection**
2626 2626  
2627 2627  **1）Hardware wiring diagram**
image-20220811104012-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -113.6 KB
Content
image-20220811115454-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -204.7 KB
Content
image-20220811140308-1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -122.3 KB
Content
image-20220811140530-2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.Ben
Size
... ... @@ -1,1 +1,0 @@
1 -126.0 KB
Content