Skip to Content

Changes for page 12 PLC Protocol OLD

Last modified by Mora Zhou on 2024/12/05 14:53
From version 23.1
edited by Hunter
on 2022/08/15 10:55
Change comment: There is no comment for this version
To version 66.1
edited by Ben
on 2022/08/29 14:06
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Hunter
1 +XWiki.Ben
Content
... ... @@ -85,6 +85,389 @@
85 85  
86 86  Click [OK] button to save settings and close the dialog;
87 87  
88 += Create communication with WECON PLC =
89 +
90 +
91 +Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
92 +
93 +**HMI Settings**
94 +
95 +(% class="table-bordered" %)
96 +|**Item**|**Settings**|**Note**
97 +|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
98 +|Connection|RS422/RS485|
99 +|Baud rate|9600|
100 +|Data bit|7|
101 +|Parity|EVEN|
102 +|Stop bit|1|
103 +|PLC station No.|1|
104 +
105 +**Address List**
106 +
107 +(% class="table-bordered" %)
108 +|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
109 +|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
110 +|Y|Y|Y o|0~~303237|
111 +|M|M|M d|0~~99999|
112 +|T|T|T d|0~~99999|
113 +|C|C|C d|0~~99999|
114 +|S|S|S d|0~~99999|
115 +|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
116 +|Y|Y|Y o|0~~303237|
117 +|M|M|M d|0~~99999|
118 +|T|T|T d|0~~99999|
119 +|C|C|C d|0~~199|
120 +|D|D|D d|0~~7999|
121 +|S|S|S d|0~~99999|
122 +|SD|SD|SD d|8000~~9999|
123 +
124 +**Cable Wiring**
125 +
126 +* **RS485**
127 +
128 +(% style="text-align:center" %)
129 +[[image:12.PLC Protocol_html_1897d92be6948d58.png||data-xwiki-image-style-alignment="center" height="223" width="393" class="img-thumbnail"]]
130 +
131 +* **RS422**
132 +
133 +(% style="text-align:center" %)
134 +[[image:12.PLC Protocol_html_5c7fca9a70da2ee8.png||data-xwiki-image-style-alignment="center" height="247" width="389" class="img-thumbnail"]]
135 +
136 +**✎Note:**
137 +
138 +* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
139 +* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
140 +
141 +[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
142 +
143 +== HMI settings ==
144 +
145 +**Download PIStudio Software**
146 +
147 +Please visit the link below to get the latest version PIstudio for HMI programming:
148 +
149 +* [[Download link>>doc:PIStudio.Download.3 Software.WebHome]]
150 +
151 +**Create a new HMI project connect with PLC**
152 +
153 +Check the link below for the video to show you how to get started with a new project
154 +
155 +* [[Video>>https://youtu.be/0FpmDZe_8U8]]
156 +
157 +For more videos, please visit our Youtube channel: [[http:~~/~~/www.youtube.com/user/Wecon2004/videos>>url:http://www.youtube.com/user/Wecon2004/videos]]
158 +
159 +**General**
160 +
161 +HMI could communicate with PLC and support many PLC protocols.  It is easy to operate and set communication parameters. This demo shows how to make a communication with PLC device, use WECON LX3V Series PLC as an example.
162 +
163 +**Protocol settings**
164 +
165 +The communication between two devices requires a protocol. The following contents show the steps of protocol settings.
166 +
167 +Please select the protocol, when creating a new project.
168 +
169 +1. Select the COM port for communication;
170 +1. PLC type: It means PLC brand, like WECON;
171 +1. PLC model: It shows the model of PLC, such as LX3V;
172 +
173 +(% style="text-align:center" %)
174 +[[image:image-20220819093729-1.png]]
175 +
176 +If you want to change the protocol for existing project, please click [Program] → [Communication] to open the [Communication] windows, shown as the following figure.
177 +
178 +(% style="text-align:center" %)
179 +[[image:image-20220819093729-2.png]]
180 +
181 +
182 +The steps to change the protocol for project are as follows.
183 +
184 +1. Click [Setting] to open the [Communication device] window;
185 +1. Select communication port, such as COM1;
186 +1. Select Serial port for communication, such as RS422;
187 +1. Select device type (device brand), such as WECON;
188 +1. Select the protocol for communication, such as WECON LX3V;
189 +
190 +(% style="text-align:center" %)
191 +[[image:image-20220819093729-3.png]]
192 +
193 +**Parameter settings**
194 +
195 +The parameters settings are in [Communication] window, shown as following below.
196 +
197 +1. Click [Setting] to open the [COM port setting] window;
198 +1. Set the parameters such as [connection], [Baud rate] and so on;
199 +
200 +(% style="text-align:center" %)
201 +[[image:image-20220819093729-4.png||height="636" width="818"]]
202 +
203 +(% start="3" %)
204 +1. Click [Setting] to open [Timeout] setting window, you could set the parameters according your requirements, or just use the default value.
205 +
206 +(% style="text-align:center" %)
207 +[[image:image-20220819093729-5.png]]
208 +
209 +**Set PLC address in HMI screen**
210 +
211 +1. Place the objects to HMI screen;
212 +1. Double-click the object to open the setting window;
213 +1. Click “Edit” to open the address setting windows;
214 +1. Connection: select the serial port in HMI;
215 +1. Address type: All the PLC address types will be display in this list, such as M;
216 +1. Address No.: Please input the number of this address, such as 0;
217 +
218 +[[image:image-20220819093729-6.jpeg]]
219 +
220 +**Communication cable**
221 +
222 +In order to ensure the stability of communication, please use the twisted-pair communication cable with good grounding. The following figure shows the pin out definition.
223 +
224 +(% style="text-align:center" %)
225 +[[image:image-20220819093729-7.png]]
226 +
227 +**HMI communication PLC use Modbus **
228 +
229 +* HMI setting: [[https:~~/~~/docs.we-con.com.cn/bin/view/PIStudio/12.PLC%20protocols/>>https://docs.we-con.com.cn/bin/view/PIStudio/12.PLC%20protocols/]]
230 +* PLC setting: [[https:~~/~~/docs.we-con.com.cn/bin/view/PLC%20Editor/8.1.%09Communication/>>https://docs.we-con.com.cn/bin/view/PLC%20Editor/8.1.%09Communication/]]
231 +
232 +== PLC settings ==
233 +
234 +**Download PLC Software**
235 +
236 +Please visit below link to get the latest version PLC Editor for HMI programming
237 +
238 +* LX3V:[[Download link>>doc:PLC Editor.10 Hardware .Software.WebHome]]
239 +* LX5V:[[Download link>>doc:PLC Editor2.Download.03 Software.WebHome]]
240 +
241 +**Start a new PLC project**
242 +
243 +Start a new PLC project by clicking “New” on the left top corner of screen, select the PLC mode from the drop-down list.
244 +
245 +(% style="text-align:center" %)
246 +[[image:image-20220819101447-3.jpeg]]
247 +
248 +
249 +
250 +**Add a new instruction **
251 +
252 +Double click on the ladder, select the ladder symbol (instruction) from the drop-down list, then enter the address for this symbol.
253 +
254 +(% style="text-align:center" %)
255 +[[image:image-20220819105530-1.png]]
256 +
257 +You could also select the ladder symbol from the menu bar directly.
258 +
259 +[[image:image-20220819093729-11.png]]
260 +
261 +[[image:image-20220819093729-12.png]]
262 +
263 +**Add comment to PLC program**
264 +
265 +(% style="text-align:center" %)
266 +[[image:image-20220819105630-3.png]]
267 +
268 +**Add the statement to PLC program**
269 +
270 +Add the statement by single click on “Statement”, when finished, single click on “Statement” again to go back to Ladder edit.
271 +
272 +(% style="text-align:center" %)
273 +[[image:image-20220819105644-4.png]]
274 +
275 +**Compile **
276 +
277 +You need to compile the PLC program before downloading or running Off-line simulator. The background color will be changed from purple to white when there is no error.
278 +
279 +[[image:image-20220819093729-15.png]]
280 +
281 +**Download setting **
282 +
283 +Click on “Transfer Setup” to select download mode.
284 +
285 +[[image:image-20220820150853-1.png]]**Download PLC program to PLC**
286 +
287 +Quick select the parameters and main program of PLC program, then download to PLC, “Yes”-”Yes”-”OK”
288 +
289 +[[image:image-20220819093729-17.png]]
290 +
291 +**Upload PLC program from PLC**
292 +
293 +Read the PLC program from PLC to computer.
294 +
295 +[[image:image-20220819093729-18.png]]
296 +
297 +**Device monitor**
298 +
299 +Monitor the value of certain address in PLC, double click “Current value” to change the value in this address.
300 +
301 +[[image:image-20220819093730-19.png]]
302 +
303 +**Online monitor**
304 +
305 +Monitor the each address in PLC by online monitor. Changing the state or value in PLC is also allowd.
306 +
307 +[[image:image-20220819093730-20.png]]
308 +
309 +**Monitor edit**
310 +
311 +In this mode, you could edit the PLC program during PLC is running. 
312 +
313 +
314 +(% style="text-align:center" %)
315 +[[image:image-20220819105928-9.png||height="229" width="669"]]
316 +
317 += **HMI and Wecon LX5V serial communication** =
318 +
319 +This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
320 +
321 +**Software configuration of PLC**
322 +
323 +**1）PLC programming software**
324 +
325 +[[image:image-20220810164710-1.png]]
326 +
327 +**2）New PLC project**
328 +
329 +Click New Project and select the PLC model.
330 +
331 +[[image:image-20220810172412-1.png]]
332 +
333 +
334 +**3）Set Serial port parameters**
335 +
336 +Follow the steps below to configure Serial port parameters
337 +
338 +Baud rate：115200
339 +
340 +Data bit：8
341 +
342 +Stop bit：1
343 +
344 +Parity：No verification
345 +
346 +[[image:image-20220810165759-3.png]]
347 +
348 +
349 +**4）Registers list**
350 +
351 +[[image:image-20220811102219-3.png]]
352 +
353 +
354 +**HMI software configuration**
355 +
356 +**1）HMI programming software**
357 +
358 + [[image:image-20220810171237-4.png]]
359 +
360 +**2）New HMI project**
361 +
362 +Click New Project and select the HMI model.
363 +
364 +[[image:image-20220810172010-5.png]]
365 +
366 +**3）Set communication port parameters**
367 +
368 +Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
369 +
370 +Baud rate：115200
371 +
372 +Data bit：8
373 +
374 +Stop bit：1
375 +
376 +Parity：No verification
377 +
378 +
379 +[[image:image-20220811104012-1.png]]
380 +
381 +
382 +**hardware connection**
383 +
384 +**1）Hardware wiring diagram**
385 +
386 +This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
387 +
388 +[[image:image-20220811103005-4.png]]
389 +
390 +
391 +[[image:image-20220811103227-7.png]]
392 +
393 +The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
394 +
395 +== **HMI and Wecon LX5V-N Ethernet communication** ==
396 +
397 +(% id="cke_bm_147709S" style="display:none" %) (%%)This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
398 +
399 +
400 +**Software configuration of PLC**
401 +
402 +**1）PLC programming software**
403 +
404 +[[image:image-20220810164710-1.png]]
405 +
406 +**2）New PLC project**
407 +
408 +Click New Project and select the PLC model.
409 +
410 +[[image:image-20220811115454-1.png]]
411 +
412 +
413 +**3）Set Ethernet port parameters**
414 +
415 +Follow the steps below to configure Ethernet parameters
416 +
417 +PLC IP address：192.168.39.200
418 +
419 +default gateway：192.168.39.1
420 +
421 +subnet mask：255.255.255.0
422 +
423 +[[image:image-20220811140530-2.png]]
424 +
425 +
426 +**4）Registers list**
427 +
428 +[[image:image-20220811102219-3.png]]
429 +
430 +
431 +**HMI software configuration**
432 +
433 +**1）HMI programming software**
434 +
435 + [[image:image-20220810171237-4.png]]
436 +
437 +**2）New HMI project**
438 +
439 +Click New Project and select the HMI model.
440 +
441 +[[image:image-20220810172010-5.png]]
442 +
443 +**3）Set communication port parameters**
444 +
445 +Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
446 +
447 +HMI IP address：192.168.39.201
448 +
449 +default gateway：192.168.39.1
450 +
451 +subnet mask：255.255.255.0
452 +
453 +[[image:image-20220811170753-2.png]]
454 +
455 +Next, click Communication Settings to configure the IP of the HMI communication object.
456 +
457 +[[image:image-20220811163047-1.png]]
458 +
459 +**hardware connection**
460 +
461 +**1）Hardware wiring diagram**
462 +
463 +This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
464 +
465 +[[image:image-20220811170248-1.png]]
466 +
467 +The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
468 +
469 += =
470 +
88 88  = **Allen-Bradley** =
89 89  
90 90  == **FreeTag Ethernet/IP (CompactLogix)** ==
... ... @@ -193,7 +193,7 @@
193 193  * **Word address S:** The word address ranges from 0 to 255 (decimal).
194 194  * **Word address TS:** The address ranges from 000.0 to ffff. The first and second f from left to right represents the block number (hexadecimal); The third and fourth f from left to right represent the word address (hexadecimal).
195 195  
196 -**✎Note: **Register address TP, CS, CP, N, F and TS address edit tare he same. D indicates decimal, and F indicates hexadecimal. Different PLC models may support different registers. See the following table.
579 +**✎Note: **Register address TP, CS, CP, N, F and TS address edit are same. D indicates decimal, and F indicates hexadecimal. Different PLC models may support different registers. See the following table.
197 197  
198 198  |(% style="width:393px" %)**PLC bit address type**|(% style="width:350px" %)**Address format**|(% style="width:333px" %)**Address range**
199 199  |(% style="width:393px" %)I|(% style="width:350px" %)dd.dd|(% style="width:333px" %)I 0.0 ~~ 255.15
... ... @@ -1896,7 +1896,7 @@
1896 1896  
1897 1897  == **LOGO Ethernet** ==
1898 1898  
1899 -Supported Series: Siemens Logo
2282 +Supported Series: Siemens Logo 0BA0 series
1900 1900  
1901 1901  **HMI Settings**
1902 1902  
... ... @@ -1959,9 +1959,8 @@
1959 1959  Set PLC IP in [Device IP] settings;
1960 1960  
1961 1961  (% style="text-align:center" %)
1962 -[[image:12.PLC Protocol_html_573fc64ad393cd4f.png||data-xwiki-image-style-alignment="center" height="655" width="379" class="img-thumbnail"]]
2345 +[[image:SiemensLOGODeviceIP.png]]
1963 1963  
1964 -
1965 1965  Enable HMI Ethernet in [Project Settings];
1966 1966  
1967 1967  (% style="text-align:center" %)
... ... @@ -2013,7 +2013,7 @@
2013 2013  [[image:S7-XXXCommunication Settings.png]]
2014 2014  
2015 2015  (% style="text-align:center" %)
2016 -[[image:S7-XXXCommunication SettingsPI.png]]
2398 +[[image:S7-XXXCommunication SettingsPIStudio.png||alt="S7-XXXCommunication SettingsPI.png"]]
2017 2017  
2018 2018  **Address List**
2019 2019  
... ... @@ -2264,63 +2264,8 @@
2264 2264  
2265 2265  **✎Note:** COM3 only available in PI8000/PI9000 series.
2266 2266  
2267 -= **WECON PLC** =
2649 += =
2268 2268  
2269 -Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
2270 -
2271 -**HMI Settings**
2272 -
2273 -(% class="table-bordered" %)
2274 -|**Item**|**Settings**|**Note**
2275 -|Protocol|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM|
2276 -|Connection|RS422/RS485|
2277 -|Baud rate|9600|
2278 -|Data bit|7|
2279 -|Parity|EVEN|
2280 -|Stop bit|1|
2281 -|PLC station No.|1|
2282 -
2283 -**Address List**
2284 -
2285 -(% class="table-bordered" %)
2286 -|**Type**|**Device registers**|**HMI registers**|**Format**|**Range**|**Note**
2287 -|(% rowspan="6" %)Bit|X|X|Xo|0~~303237|
2288 -|Y|Y|Y o|0~~303237|
2289 -|M|M|M d|0~~99999|
2290 -|T|T|T d|0~~99999|
2291 -|C|C|C d|0~~99999|
2292 -|S|S|S d|0~~99999|
2293 -|(% rowspan="8" %)Word|X|X|Xo|0~~303237|
2294 -|Y|Y|Y o|0~~303237|
2295 -|M|M|M d|0~~99999|
2296 -|T|T|T d|0~~99999|
2297 -|C|C|C d|0~~199|
2298 -|D|D|D d|0~~7999|
2299 -|S|S|S d|0~~99999|
2300 -|SD|SD|SD d|8000~~9999|
2301 -
2302 -**Cable Wiring**
2303 -
2304 -* **RS485**
2305 -
2306 -(% style="text-align:center" %)
2307 -[[image:12.PLC Protocol_html_5e9a81a14106da9e.png||data-xwiki-image-style-alignment="center" height="223" width="392" class="img-thumbnail"]]
2308 -
2309 -(% style="text-align:center" %)
2310 -[[image:12.PLC Protocol_html_1897d92be6948d58.png||data-xwiki-image-style-alignment="center" height="223" width="393" class="img-thumbnail"]]
2311 -
2312 -* **RS422**
2313 -
2314 -(% style="text-align:center" %)
2315 -[[image:12.PLC Protocol_html_5c7fca9a70da2ee8.png||data-xwiki-image-style-alignment="center" height="247" width="389" class="img-thumbnail"]]
2316 -
2317 -**✎Note:**
2318 -
2319 -* HMI COM3 is available in PI8000 series and COM3 is in COM2(hardware PIN 7 and PIN 8) .
2320 -* If PLC <= 20 points,such as LX3V-1208/LX3V-0806 PLC,PLC RS485A and RS485B mean PLC COM2 RS485+ and RS485- .PLC COM2 can support modbus. Please refer to PLC COM2 setting manual.
2321 -
2322 -[[https:~~/~~/drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing>>url:https://drive.google.com/drive/folders/13rgso7oUlatZQN_SNEcJCcN4toEdDPoP?usp=sharing]]
2323 -
2324 2324  = **Printer** =
2325 2325  
2326 2326  == **TSPL label printer** ==
... ... @@ -2489,155 +2489,35 @@
2489 2489  **✎Note:** COM3 only available in PI8000/PI9000 series.
2490 2490  
2491 2491  
2492 -== **1. HMI and Wecon LX5V serial communication** ==
2819 += **Schneider MODBUS RTU** =
2493 2493  
2494 -This example introduces the establishment of serial port communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2821 +**HMI Setting**
2495 2495  
2823 +|=**Parameters**|=**Recommended**|=**Notes**
2824 +|**Protocol**|(% colspan="1" %)Schneider MODBUS RTU|
2825 +|Connection|RS485|
2826 +|**Baud rate**|19200|
2827 +|**Data bit**|8|
2828 +|**Parity**|Even|
2829 +|**Stop bit**|1|
2830 +|**PLC station No.**|1|
2496 2496  
2497 -**Software configuration of PLC**
2832 +**PLC Setting**
2498 2498  
2499 -**1）PLC programming software**
2834 +|=(% scope="row" %)**Communication mode**|Modbus RTU protocol
2500 2500  
2501 -[[image:image-20220810164710-1.png]]
2836 +**Device Address**
2502 2502  
2503 -**2）New PLC project**
2838 +|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo**
2839 +|B|IX|DDDDDo|0 ~~ 655357|Input bit (read only)
2840 +|B|QX|DDDDDo|0 ~~ 655357|Write multiple coils
2841 +|B|MX|DDDDDDo|0 ~~ 9999997|Output register bit (octal)
2842 +|W|MW|DDDDDD|0 ~~ 999999|Output register
2843 +|DW|MD|DDDDDD|0 ~~ 999999|Output register
2504 2504  
2505 -Click New Project and select the PLC model.
2845 +**Wiring Diagram**
2506 2506  
2507 -[[image:image-20220810172412-1.png]]
2847 +**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector.
2508 2508  
2509 -
2510 -**3）Set Serial port parameters**
2511 -
2512 -Follow the steps below to configure Serial port parameters
2513 -
2514 -Baud rate：115200
2515 -
2516 -Data bit：8
2517 -
2518 -Stop bit：1
2519 -
2520 -Parity：No verification
2521 -
2522 -[[image:image-20220810165759-3.png]]
2523 -
2524 -
2525 -**4）Registers list**
2526 -
2527 -[[image:image-20220811102219-3.png]]
2528 -
2529 -
2530 -**HMI software configuration**
2531 -
2532 -**1）HMI programming software**
2533 -
2534 - [[image:image-20220810171237-4.png]]
2535 -
2536 -**2）New HMI project**
2537 -
2538 -Click New Project and select the HMI model.
2539 -
2540 -[[image:image-20220810172010-5.png]]
2541 -
2542 -**3）Set communication port parameters**
2543 -
2544 -Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
2545 -
2546 -Baud rate：115200
2547 -
2548 -Data bit：8
2549 -
2550 -Stop bit：1
2551 -
2552 -Parity：No verification
2553 -
2554 -
2555 -[[image:image-20220811104012-1.png]]
2556 -
2557 -
2558 -**hardware connection**
2559 -
2560 -**1）Hardware wiring diagram**
2561 -
2562 -This example introduces WeconHMI with LX5V PLC to establish communication through serial port. The connection diagram is as follows:
2563 -
2564 -[[image:image-20220811103005-4.png]]
2565 -
2566 -
2567 -[[image:image-20220811103227-7.png]]
2568 -
2569 -The above are all the steps for establishing serial port communication between Wecon HMI with LX5V PLC.
2570 -
2571 -== **2. HMI and Wecon LX5V-N Ethernet communication** ==
2572 -
2573 -(% id="cke_bm_147709S" style="display:none" %) (%%)This example introduces the establishment of Ethernet communication between Wecon HMI and LX5V. It is introduced through three parts: PLC software configuration, HMI software configuration, and hardware wiring.
2574 -
2575 -
2576 -**Software configuration of PLC**
2577 -
2578 -**1）PLC programming software**
2579 -
2580 -[[image:image-20220810164710-1.png]]
2581 -
2582 -**2）New PLC project**
2583 -
2584 -Click New Project and select the PLC model.
2585 -
2586 -[[image:image-20220811115454-1.png]]
2587 -
2588 -
2589 -**3）Set Ethernet port parameters**
2590 -
2591 -Follow the steps below to configure Ethernet parameters
2592 -
2593 -PLC IP address：192.168.39.200
2594 -
2595 -default gateway：192.168.39.1
2596 -
2597 -subnet mask：255.255.255.0
2598 -
2599 -[[image:image-20220811140530-2.png]]
2600 -
2601 -
2602 -**4）Registers list**
2603 -
2604 -[[image:image-20220811102219-3.png]]
2605 -
2606 -
2607 -**HMI software configuration**
2608 -
2609 -**1）HMI programming software**
2610 -
2611 - [[image:image-20220810171237-4.png]]
2612 -
2613 -**2）New HMI project**
2614 -
2615 -Click New Project and select the HMI model.
2616 -
2617 -[[image:image-20220810172010-5.png]]
2618 -
2619 -**3）Set communication port parameters**
2620 -
2621 -Click the project setting button on the left to configure the IP address of the HMI machine to ensure that the HMI and PLC IP remain in a local area network.
2622 -
2623 -HMI IP address：192.168.39.201
2624 -
2625 -default gateway：192.168.39.1
2626 -
2627 -subnet mask：255.255.255.0
2628 -
2629 -[[image:image-20220811170753-2.png]]
2630 -
2631 -Next, click Communication Settings to configure the IP of the HMI communication object.
2632 -
2633 -[[image:image-20220811163047-1.png]]
2634 -
2635 -**hardware connection**
2636 -
2637 -**1）Hardware wiring diagram**
2638 -
2639 -This example introduces WeconHMI with LX5V-N PLC to establish communication through ethernet. The connection diagram is as follows:
2640 -
2641 -[[image:image-20220811170248-1.png]]
2642 -
2643 -The above are all the steps for establishing ethernet communication between Wecon HMI with LX5V PLC.
2849 +(% style="text-align:center" %)
2850 +[[image:image-20220817154212-1.jpeg||height="315" width="554" class="img-thumbnail"]]
S7-XXXCommunication SettingsPIStudio.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Hunter
Size
... ... @@ -1,0 +1,1 @@
1 +24.9 KB
Content
SiemensLOGODeviceIP.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Hunter
Size
... ... @@ -1,0 +1,1 @@
1 +24.9 KB
Content
image-20220817154212-1.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +51.8 KB
Content
image-20220819093729-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +10.3 KB
Content
image-20220819093729-10.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +79.4 KB
Content
image-20220819093729-12.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +147.9 KB
Content
image-20220819093729-15.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +74.6 KB
Content
image-20220819093729-17.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +115.0 KB
Content
image-20220819093729-18.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +112.1 KB
Content
image-20220819093729-2.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +34.1 KB
Content
image-20220819093729-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +44.2 KB
Content
image-20220819093729-4 (1).png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +82.4 KB
Content
image-20220819093729-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +82.4 KB
Content
image-20220819093729-5.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +6.6 KB
Content
image-20220819093729-6.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +100.2 KB
Content
image-20220819093729-7.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +46.9 KB
Content
image-20220819093730-19.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +122.5 KB
Content
image-20220819093730-20.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +99.6 KB
Content
image-20220819101447-3.jpeg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +56.6 KB
Content
image-20220819105530-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +1.0 MB
Content
image-20220819105630-3.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +1.1 MB
Content
image-20220819105644-4.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +942.6 KB
Content
image-20220819105928-9.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +72.6 KB
Content
image-20220820150853-1.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.Stone
Size
... ... @@ -1,0 +1,1 @@
1 +171.7 KB
Content