Skip to Content

Changes for page 09 Electronic cam

Last modified by Devin Chen on 2025/01/09 11:57
From version 18.1
edited by Devin Chen
on 2025/01/09 11:57
Change comment: There is no comment for this version
To version 14.1
edited by Devin Chen
on 2024/06/21 14:50
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -9,7 +9,7 @@
9 9  -[DEGEAR (s1) (s2) (s3) (d1) (d2)]
10 10  
11 11  (% style="text-align:center" %)
12 -[[image:PixPin_2024-12-31_14-57-19.png||alt="09_html_da882b8c1ba50fe6.png" class="img-thumbnail"]]
12 +[[image:09_html_da882b8c1ba50fe6.png||height="388" width="700" class="img-thumbnail"]]
13 13  
14 14  **Content, range and data type**
15 15  
... ... @@ -907,7 +907,7 @@
907 907  Aperiodic electronic cam: control table execution times; when the value is H0001, the electronic cam will stop after executing once;
908 908  
909 909  When the value is HFFFF, it will become a periodic electronic cam execution.
910 -)))|(% style="width:126px" %)1|(% style="width:154px" %)1 to 65535
910 +)))|(% style="width:126px" %)11|(% style="width:154px" %)1 to 65535
911 911  |15|ECAM start delay pulse setting (low word)|(% rowspan="2" style="width:944px" %)(((
912 912  Periodic electronic cam: reserved
913 913  
... ... @@ -1340,7 +1340,7 @@
1340 1340  
1341 1341  ③. After leaving the synchronization zone, the slave axis will decelerate and move back to the origin to complete a cycle of cutting. After knowing the stroke, the speed relationship can be drawn.
1342 1342  
1343 -2) In the cutting process, the most important thing is speed synchronization. For example, when the cutting knife contacts the material, it must be synchronized with the material speed. If the cutting knife speed is greater than the synchronous speed during contact, a force that pulls the material forward will cause the material to be uneven. If the speed is lower than the material speed, it will appear. Blocking phenomenon.
1343 +2) In the peeling process, the most important thing is speed synchronization. For example, when the cutting knife contacts the material, it must be synchronized with the material speed. If the cutting knife speed is greater than the synchronous speed during contact, a force that pulls the material forward will cause the material to be uneven. If the speed is lower than the material speed, it will appear. Blocking phenomenon.
1344 1344  
1345 1345  3) The planning of the synchronization area will affect the operation of the actual equipment. If the synchronization area is larger in a cutting cycle, the acceleration and deceleration time will be smaller, which means that the equipment needs to be accelerated and decelerated in a short time. For motors and machines The impact of the cutter is very large, and it is easy to cause the servo over-current alarm and the equipment cannot operate normally.
1346 1346  
... ... @@ -1661,7 +1661,7 @@
1661 1661  |(% rowspan="2" style="width:118px" %)Parameter 4|(% style="width:118px" %)Address 6|(% rowspan="2" style="width:134px" %)Slave axis synchronization magnification|(% rowspan="2" style="width:115px" %)Floating|(% rowspan="2" style="width:464px" %)(((
1662 1662  Calculation method one:
1663 1663  
1664 -In the synchronization zone, the speed of the master axis and the slave axis are equal, and the synchronization magnification calculation method:[[image:09_html_d11c191bffc9429b.jpg||class="img-thumbnail"]]
1664 +In the synchronization zone, the speed of the master axis and the slave axis are equal, and the synchronization magnification calculation method:
1665 1665  
1666 1666  V1(V2)=Master (slave) axis speed
1667 1667  
PixPin_2024-12-31_14-57-19.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.DevinChen
Size
... ... @@ -1,1 +1,0 @@
1 -53.0 KB
Content