Skip to Content

Changes for page 09 Electronic cam

Last modified by Jim(Forgotten) on 2025/06/23 18:38
From version 19.1
edited by Jim(Forgotten)
on 2025/06/23 15:14
Change comment: There is no comment for this version
To version 15.1
edited by Devin Chen
on 2024/06/21 14:51
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Jim
1 +XWiki.DevinChen
Content
... ... @@ -9,7 +9,7 @@
9 9  -[DEGEAR (s1) (s2) (s3) (d1) (d2)]
10 10  
11 11  (% style="text-align:center" %)
12 -[[image:PixPin_2024-12-31_14-57-19.png||alt="09_html_da882b8c1ba50fe6.png" class="img-thumbnail"]]
12 +[[image:09_html_da882b8c1ba50fe6.png||height="388" width="700" class="img-thumbnail"]]
13 13  
14 14  **Content, range and data type**
15 15  
... ... @@ -829,12 +829,8 @@
829 829  
830 830  (Confirm before using electronic cam)
831 831  )))|(% style="width:944px" %)(((
832 -Bit0: Delayed start enable
832 +Bit0: Delayed start enable Bit1: Start at specified position Bit2: Spindle zoom
833 833  
834 -Bit1: Start at specified position
835 -
836 -Bit2: Spindle zoom
837 -
838 838  Bit3: zoom from axis
839 839  
840 840  Bit5: Use external start signal
... ... @@ -911,7 +911,7 @@
911 911  Aperiodic electronic cam: control table execution times; when the value is H0001, the electronic cam will stop after executing once;
912 912  
913 913  When the value is HFFFF, it will become a periodic electronic cam execution.
914 -)))|(% style="width:126px" %)1|(% style="width:154px" %)1 to 65535
910 +)))|(% style="width:126px" %)11|(% style="width:154px" %)1 to 65535
915 915  |15|ECAM start delay pulse setting (low word)|(% rowspan="2" style="width:944px" %)(((
916 916  Periodic electronic cam: reserved
917 917  
... ... @@ -1344,7 +1344,7 @@
1344 1344  
1345 1345  ③. After leaving the synchronization zone, the slave axis will decelerate and move back to the origin to complete a cycle of cutting. After knowing the stroke, the speed relationship can be drawn.
1346 1346  
1347 -2) In the cutting process, the most important thing is speed synchronization. For example, when the cutting knife contacts the material, it must be synchronized with the material speed. If the cutting knife speed is greater than the synchronous speed during contact, a force that pulls the material forward will cause the material to be uneven. If the speed is lower than the material speed, it will appear. Blocking phenomenon.
1343 +2) In the peeling process, the most important thing is speed synchronization. For example, when the cutting knife contacts the material, it must be synchronized with the material speed. If the cutting knife speed is greater than the synchronous speed during contact, a force that pulls the material forward will cause the material to be uneven. If the speed is lower than the material speed, it will appear. Blocking phenomenon.
1348 1348  
1349 1349  3) The planning of the synchronization area will affect the operation of the actual equipment. If the synchronization area is larger in a cutting cycle, the acceleration and deceleration time will be smaller, which means that the equipment needs to be accelerated and decelerated in a short time. For motors and machines The impact of the cutter is very large, and it is easy to cause the servo over-current alarm and the equipment cannot operate normally.
1350 1350  
PixPin_2024-12-31_14-57-19.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.DevinChen
Size
... ... @@ -1,1 +1,0 @@
1 -53.0 KB
Content