Wiki source code of 01 Precautions
Last modified by Wecon on 2025/09/03 21:03
Show last authors
| author | version | line-number | content |
|---|---|---|---|
| 1 | = **Safety** = | ||
| 2 | |||
| 3 | This section explains important items that users must observe, such as product confirmation, storage, transportation, installation, wiring, operation, inspection, and disposal. Follow the steps required in this manual for trial operation. | ||
| 4 | |||
| 5 | (% class="table-bordered" %) | ||
| 6 | |=((( | ||
| 7 | (% style="text-align:center" %) | ||
| 8 | [[image:1.Safety Instruction_html_f547c64fa62591ff.png||height="34" width="130"]] | ||
| 9 | ))) | ||
| 10 | |((( | ||
| 11 | * After the power is turned off for more than 5 minutes and the power indicator is off, use a multimeter to confirm that the voltage across the high-voltage capacitor has dropped to a safe voltage, and then perform the disassembly of the driver, otherwise electric shock may be caused due to residual voltage. | ||
| 12 | * Do not touch the inside of the Servo drive, otherwise electric shock may be caused. | ||
| 13 | * To avoid an electric shock, insulate the connections of the power supply terminals. | ||
| 14 | * To prevent an electric shock, always connect the protective earth (PE) terminal (marked) of the Servo to earth well. | ||
| 15 | * Install the Servo drive, Servo motor, and external brake resistor on incombustible material. Installing them directly or close to combustibles would lead to smoke or a fire. | ||
| 16 | * Always connect the magnetic contactor and the non-fuse breaker between the power supply and the main circuit power supply of the Servo driver (three-phase is L1, L2, L3). otherwise, when the device fails, the high current may not be cut off. This could cause a fire. | ||
| 17 | * Provide adequate protection to prevent screws and other conductive matter, oil and other combustible matter from entering the Servo drive and Servo motor. | ||
| 18 | * When the Servo motor and the machine are connected, if an operation error occurs, it would not only cause mechanical damage, but may also lead to personal safety accidents. | ||
| 19 | * Do not damage or pull the cable with force, do not subject the cable to excessive force, or place heavy objects under it, otherwise electric shock may occur, causing the product to stop operating or burn out. | ||
| 20 | * Do not use the brake function of motor for normal braking, otherwise it may cause a malfunction. | ||
| 21 | * Except for the designated operator, please do not set up, disassemble or repair the equipment, otherwise electric shock or injury may be caused. | ||
| 22 | * Do not remove the cover, cables, connectors, and optional accessories while the power is on. Otherwise, electric shock may occur. | ||
| 23 | * Install a stop device on the machine side to ensure safety. | ||
| 24 | * Please take measures to ensure that the personal safety would not be endangered when restarting, otherwise it may cause injury. | ||
| 25 | * Do not modify this product, otherwise it may cause personal injury or mechanical damage. | ||
| 26 | ))) | ||
| 27 | |||
| 28 | = **Storage and Handling** = | ||
| 29 | |||
| 30 | (% class="table-bordered" %) | ||
| 31 | |=((( | ||
| 32 | (% style="text-align:center" %) | ||
| 33 | [[image:1.Safety Instruction_html_6db94f5d0421f97a.png||height="32" width="130"]] | ||
| 34 | ))) | ||
| 35 | |Please keep and install in the following environment:((( | ||
| 36 | * Locations without direct sunlight. | ||
| 37 | * Locations where the ambient temperature does not exceed the product specifications. | ||
| 38 | * Locations where the relative humidity does not exceed the product specifications. | ||
| 39 | * Locations where condensation does not occur due to rapid temperature changes. | ||
| 40 | * No corrosive gas or flammable gas. | ||
| 41 | * No flammable materials nearby. | ||
| 42 | * Locations with less dust, salt and metal powder. | ||
| 43 | * Locations without water, oil, medicine plashing etc.. | ||
| 44 | * Locations where vibration or shock would not affect the product (places that exceed product specifications). | ||
| 45 | * Location that would not be exposed to radiation. | ||
| 46 | ))) | ||
| 47 | |((( | ||
| 48 | Storage or installation in environments other than those described above could cause product failure or damage: | ||
| 49 | |||
| 50 | Please use proper method for transportatoin according to the weight of the product. | ||
| 51 | |||
| 52 | Do not hold the motor cable or motor shaft for transportation. | ||
| 53 | |||
| 54 | When operating the Servo unit and Servo motor, pay attention to sharp parts such as the corners of the equipment. | ||
| 55 | ))) | ||
| 56 | |||
| 57 | = **Installation** = | ||
| 58 | |||
| 59 | (% class="table-bordered" %) | ||
| 60 | |=((( | ||
| 61 | (% style="text-align:center" %) | ||
| 62 | [[image:1.Safety Instruction_html_6db94f5d0421f97a.png||height="32" width="130"]] | ||
| 63 | ))) | ||
| 64 | |((( | ||
| 65 | * Do not install this product in a place where it would be splashed with water or an environment prone to cause corrosion. | ||
| 66 | * Please follow the requirements of the installation direction, otherwise it may cause equipment failure. | ||
| 67 | * When installing, please ensure that the specified distance between the Servo drive and the inner surface of the electrical cabinet and other machines is proper, otherwise fire or equipment failure may be caused. | ||
| 68 | * Do not apply excessive impact, otherwise it may cause equipment failure. | ||
| 69 | * Do not sit on this product or place heavy objects on it, otherwise personal injury may be caused. | ||
| 70 | * Do not use this product near flammable gas or combustible materials, otherwise there may be danger of electric shock or fire. | ||
| 71 | * Do not block the air intake and exhaust ports, and do not allow foreign matter to enter the product, or the equipment may be damaged due to the aging of internal components or cause a fire. | ||
| 72 | ))) | ||
| 73 | |||
| 74 | = **Wiring** = | ||
| 75 | |||
| 76 | (% class="table-bordered" %) | ||
| 77 | |=((( | ||
| 78 | (% style="text-align:center" %) | ||
| 79 | [[image:1.Safety Instruction_html_6db94f5d0421f97a.png||height="32" width="130"]] | ||
| 80 | ))) | ||
| 81 | |((( | ||
| 82 | * During trial operation, in order to prevent accidents, please run the Servo motor with no load (not connected to the drive shaft), otherwise injury may be caused. | ||
| 83 | * When the Servo motor is running, do not touch rotating parts, otherwise injury may be caused. | ||
| 84 | * Be sure to set proper inertia ratio, otherwise vibration may be caused. | ||
| 85 | * When installing drive on a machine a, please set the parameters corresponding to the machine in advance. Otherwise it may cause the machine to run out of control or malfunction. | ||
| 86 | * When installing drive on a machine, please put the Servo motor in a state that could be stopped Immediately at any time, otherwise injury may be caused | ||
| 87 | * When using a Servo motor on a vertical axis, install a safety device to prevent the workpiece from falling in an alarm or overtravel condition. In addition, please set the Servo lock stop when overtravel occurs, otherwise the workpiece may fall down during overtravel. | ||
| 88 | * Extreme parameter adjustments and setting changes could cause the Servo system to become unstable. Therefore, do not do this, otherwise injury may be caused. | ||
| 89 | * When an alarm occurs, reset the alarm after clearing the cause and ensuring safety, and restart the operation, otherwise injury may be caused. | ||
| 90 | * Except for special purposes, do not change the maximum speed value (P1-10). Inadvertent changes could damage the machine or cause injury. | ||
| 91 | * When the power is turned on and for a period of time after the power is turned off, the heat sink of the Servo driver, external regenerative resistor, Servo motor, etc. may become hot. Do not touch it, otherwise injury may be caused. | ||
| 92 | * If the power supply is restored after an instantaneous power failure during operation, the machine may restart suddenly, so please do not approach the machine, and press the non-stop button during power failure, and then operate after the power supply is stable | ||
| 93 | ))) | ||
| 94 | |||
| 95 | = **Maintenance and Inspection** = | ||
| 96 | |||
| 97 | (% class="table-bordered" %) | ||
| 98 | |=((( | ||
| 99 | (% style="text-align:center" %) | ||
| 100 | [[image:1.Safety Instruction_html_6db94f5d0421f97a.png||height="32" width="130"]] | ||
| 101 | ))) | ||
| 102 | |((( | ||
| 103 | * Power on and off operations should be performed by professional operators. | ||
| 104 | * During testing the insulation resistance of the driver, please cut off all connections with the driver first, otherwise it may cause drive failure. | ||
| 105 | * Do not use gasoline, alcohol, acid and alkaline detergents, otherwise discolored or damaged may be caused. | ||
| 106 | * When replacing the servo driver, please transfer the original servo driver user parameters to the new one before operation, otherwise equipment failure may be caused. | ||
| 107 | * Do not change the wiring while running, otherwise electric shock or injury may be caused. | ||
| 108 | * Do not disassemble the Servo Motor, otherwise electric shock or injury may be caused. | ||
| 109 | ))) |