Skip to Content

Wiki source code of 04 Wiring

Version 143.4 by Karen on 2023/05/15 09:55
Show last authors
1 = **Main circuit wiring** =
2
3 == Main circuit terminals ==
4
5 (((
6 **VD2A servo drive main circuit terminal distribution**
7 )))
8
9 (% style="text-align:center" %)
10 (((
11 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
12 [[**Figure 4-1 VD2A servo drive main circuit terminal distribution**>>image:image-20220611124012-2.png||height="455" id="Iimage-20220611124012-2.png" width="135"]]
13 )))
14
15 (% class="table-bordered" %)
16 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 173px;" %)**Terminal number**|=(% style="text-align: center; vertical-align: middle; width: 253px;" %)**Terminal name**|=(% style="text-align: center; vertical-align: middle; width: 650px;" %)**Terminal function**
17 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle; width:253px" %)Power input terminal|(% rowspan="3" style="width:650px" %)Single-phase 220V AC input is connected to L1 and L3.
18 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)L2
19 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)L3
20 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle; width:253px" %)Braking resistor terminal|(% rowspan="3" style="width:650px" %)(((
21 * Use internal braking resistor: short-circuit C and D.
22 * Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C;
23 )))
24 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)C
25 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)D
26 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle; width:253px" %)Motor power line terminal|(% rowspan="3" style="width:650px" %)Connect with the U, V and W of motor to power the motor.
27 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)V
28 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)W
29 |=(% style="text-align: center; vertical-align: middle; width: 173px;" %)Ground terminal|(% style="text-align:center; vertical-align:middle; width:253px" %)Ground terminal|(% style="width:650px" %)Grounding treatment of the servo drive.
30
31 Table 4-1 The name and function of VD2A servo drive main circuit terminal
32
33 **VD2B servo drive (220V) main circuit terminal distribution**
34
35 (% style="text-align:center" %)
36 (((
37 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
38 [[Figure 4-2 VD2B servo drive (220V) main circuit terminal distribution>>image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_17042d8c7761266a.gif||id="IWeconVD2SASeriesServoDrivesManual28FullV1.129_html_17042d8c7761266a.gif"]]
39 )))
40
41 (% class="table-bordered" %)
42 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 174px;" %)**Terminal number**|=(% style="text-align: center; vertical-align: middle; width: 251px;" %)**Terminal name**|=(% style="text-align: center; vertical-align: middle; width: 651px;" %)**Terminal function**
43 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle; width:251px" %)Power input terminal|(% rowspan="3" style="width:651px" %)(((
44 * Three-phase 220V AC input is connected to L1, L2, L3;
45 * Single-phase 220V AC input is connected to L1 and L3.
46 )))
47 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)L2
48 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)L3
49 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)L1C|(% rowspan="2" style="text-align:center; vertical-align:middle; width:251px" %)Control power input terminal|(% rowspan="2" style="width:651px" %)Single-phase 220V AC input is connected to L1C and L2C.
50 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)L2C
51 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle; width:251px" %)Braking resistor terminal|(% rowspan="3" style="width:651px" %)(((
52 * Use internal braking resistor: short-circuit C and D.
53 * Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
54 )))
55 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)C
56 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)D
57 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle; width:251px" %)Motor power line terminal|(% rowspan="3" style="width:651px" %)Connect with the U, V and W of motor to power the motor.
58 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)V
59 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)W
60 |=(% style="text-align: center; vertical-align: middle; width: 174px;" %)Ground terminal|(% style="text-align:center; vertical-align:middle; width:251px" %)Ground terminal|(% style="width:651px" %)Grounding treatment of the servo drive.
61
62 Table 4-2 The name and function of VD2B servo drive (220V) main circuit terminal
63
64 **VD2B servo drive (380V) main circuit terminal distribution**
65
66 (% style="text-align:center" %)
67 (((
68 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
69 [[**Figure 4-3 VD2B servo drive (380V) main circuit terminal distribution**>>image:image-20220705111045-1.jpeg||height="803" id="Iimage-20220705111045-1.jpeg" width="958"]]
70 )))
71
72 |=(% scope="row" style="width: 194px;" %)**Terminal number**|=(% style="width: 248px;" %)**Terminal name**|=(% style="width: 634px;" %)**Terminal function**
73 |=(% style="width: 194px;" %)L1|(% rowspan="3" style="width:248px" %)Power input terminal|(% rowspan="3" style="width:634px" %)Three-phase 380V AC input is connected to L1, L2, L3;
74 |=(% style="width: 194px;" %)L2
75 |=(% style="width: 194px;" %)L3
76 |=(% style="width: 194px;" %)L1C|(% rowspan="2" style="width:248px" %)Control power input terminal|(% rowspan="2" style="width:634px" %)Single-phase 380V AC input is connected to L1C and L2C.
77 |=(% style="width: 194px;" %)L2C
78 |=(% style="width: 194px;" %)P+|(% rowspan="3" style="width:248px" %)Braking resistor terminal|(% rowspan="3" style="width:634px" %)(((
79 * Use internal braking resistor: short-circuit C and D.
80 * Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
81 )))
82 |=(% style="width: 194px;" %)C
83 |=(% style="width: 194px;" %)D
84 |=(% style="width: 194px;" %)U|(% rowspan="3" style="width:248px" %)Motor power line terminal|(% rowspan="3" style="width:634px" %)Connect with the U, V and W of motor to power the motor.
85 |=(% style="width: 194px;" %)V
86 |=(% style="width: 194px;" %)W
87 |=(% style="width: 194px;" %)Ground terminal|(% style="width:248px" %)Ground terminal|(% style="width:634px" %)Grounding treatment of servo drive.
88
89 Table 4-3 The name and function of VD2B servo drive (380V) main circuit terminal
90
91 **VD2F servo drive main circuit terminal distribution**
92
93 (% style="text-align:center" %)
94 (((
95 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
96 [[**Figure 4-4 VD2F servo drive main circuit terminal distribution**>>image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6dd68f214c0f9f79.gif||id="IWeconVD2SASeriesServoDrivesManual28FullV1.129_html_6dd68f214c0f9f79.gif"]]
97 )))
98
99 (% class="table-bordered" %)
100 |=(% scope="row" style="text-align: center; vertical-align: middle; width: 160px;" %)**Terminal number**|=(% style="text-align: center; vertical-align: middle; width: 265px;" %)**Terminal name**|=(% style="text-align: center; vertical-align: middle; width: 651px;" %)**Terminal function**
101 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)L1|(% rowspan="2" style="text-align:center; vertical-align:middle; width:265px" %)Power input terminal|(% rowspan="2" style="width:651px" %)Connect single-phase 220V input power
102 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)L2
103 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle; width:265px" %)Braking resistor terminal|(% rowspan="3" style="width:651px" %)(((
104 * Use internal braking resistor: short-circuit C and D.
105 * Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
106 )))
107 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)C
108 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)D
109 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)P+|(% rowspan="2" style="text-align:center; vertical-align:middle; width:265px" %)Common DC bus terminal|(% rowspan="2" style="width:651px" %)DC bus terminal of servo drive
110 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)N
111 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle; width:265px" %)Motor power line terminal|(% rowspan="3" style="width:651px" %)Connect with the U, V and W of the motor to power the motor.
112 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)V
113 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)W
114 |=(% style="text-align: center; vertical-align: middle; width: 160px;" %)PE|(% style="text-align:center; vertical-align:middle; width:265px" %)Ground terminal|(% style="width:651px" %)Grounding treatment of the servo drive.
115
116 Table 4-3 The name and function of VD2F servo drive main circuit terminal
117
118 == Power wiring ==
119
120 **Use single-phase 220V power supply model: VD2-010SA1G and VD2-014SA1G**
121
122 (% style="text-align:center" %)
123 (((
124 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
125 [[**Figure 4-5 VD2A drive single-phase 220V main circuit wiring**>>image:image-20220705120253-1.jpeg||id="Iimage-20220705120253-1.jpeg"]]
126 )))
127
128 **Use single-phase 220V power supply model: VD2-016SA1G、VD2-019SA1G**
129
130 (% style="text-align:center" %)
131 (((
132 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
133 [[**Figure 4-6 VD2B drive single-phase 220V main circuit wiring**>>image:image-20220611155244-1.jpeg||height="1264" id="Iimage-20220611155244-1.jpeg" width="1500"]]
134 )))
135
136 **Use three-phase 220V power supply model: VD2-021SA1G、VD2-025SA1G、VD2-030SA1G**
137
138 (% style="text-align:center" %)
139 (((
140 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
141 [[**Figure 4-7 VD2B drive three-phase 220V main circuit wiring**>>image:image-20220611155302-2.jpeg||height="1292" id="Iimage-20220611155302-2.jpeg" width="1500"]]
142 )))
143
144 **Use single-phase 220V power supply model: VD2F-010SA1P、VD2F-014SA1P**
145
146 (% style="text-align:center" %)
147 (((
148 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
149 [[**Figure 4-8 VD2F drive single-phase 220V main circuit wiring**>>image:image-20220611155311-3.jpeg||height="1292" id="Iimage-20220611155311-3.jpeg" width="1500"]]
150 )))
151
152 **Use three-phase 380V power supply model: VD2-021TA1G**
153
154 (% style="text-align:center" %)
155 (((
156 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
157 [[**Figure 4-9 VD2B drive three-phase 380V main circuit wiring**>>image:image-20220705120605-3.jpeg||id="Iimage-20220705120605-3.jpeg"]]
158 )))
159
160 == Precautions ==
161
162 1. Do not connect the input power cord to the output terminals U, V, W, otherwise the servo drive will be damaged. When using the built-in braking resistor, C and D must be connected (factory default connection).
163 1. When the cables are bundled and used in pipes, etc., due to the deterioration of heat dissipation conditions, please consider the allowable current reduction rate.
164 1. When the temperature in the cabinet is higher than the cable temperature limit, please choose a cable with a larger cable temperature limit, and it is recommended that the cable wire use Teflon wire. Please pay attention to the warmth of the cable in the low temperature environment. Generally, the surface of the cable is easy to harden and break under the low temperature environment.
165 1. The bending radius of the cable should be more than 10 times the outer diameter of the cable itself to prevent the core of the cable from breaking due to long-term bending.
166
167 = **Power line connection** =
168
169 == Power line ==
170
171 Wecon VD2 series servo drives have 3 kinds of interface power cables: rectangular plug, aviation plug and in-line type.
172
173 (% class="table-bordered" %)
174 |=(% style="text-align: center; vertical-align: middle;" %)**Connector exterior**|=(% style="text-align: center; vertical-align: middle;" %)**Terminal pin distribution**|=(% style="text-align: center; vertical-align: middle;" %)**Pin description**|=(% style="text-align: center; vertical-align: middle;" %)(((
175 **Motor flange**
176 )))
177 |(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610092710-1.png||height="90" width="134"]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610092728-2.png]]|(% style="text-align:center; vertical-align:middle" %)Rectangular plug(((
178 (% class="table-bordered" %)
179 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Color**
180 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
181 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
182 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
183 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
184 )))|(% style="text-align:center; vertical-align:middle" %)(((
185 40
186
187 60
188
189 80
190 )))
191 |(% style="text-align:center; vertical-align:middle" %)[[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9335f5058d76f79a.gif]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610100433-1.png||height="135" width="146"]]|(% style="text-align:center; vertical-align:middle" %)Aviation plug(((
192 (% class="table-bordered" %)
193 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Color**
194 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Black
195 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)Yellow-green
196 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
197 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Black
198 )))|(% style="text-align:center; vertical-align:middle" %)(((
199 110
200
201 130
202 )))
203 |(% style="text-align:center; vertical-align:middle" %)[[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_77117dacdd5935b9.gif||height="114" width="130"]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611124053-4.png]]|(% style="text-align:center; vertical-align:middle" %)In-line type plug(((
204 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Color**
205 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
206 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
207 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
208 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
209 )))|(% style="text-align:center; vertical-align:middle" %)(((
210 60
211
212 80
213 )))
214
215 Table 4-4 Power cable servo motor side connector
216
217 (% class="box infomessage" %)
218 (((
219 ✎**Note:** The color of the lines is subject to the actual product. The lines described in this manual are all lines of Wecon.
220 )))
221
222 == **Brake device cable** ==
223
224 (% class="table-bordered" style="width:775px" %)
225 |=(% colspan="2" scope="row" style="text-align: center; vertical-align: middle; width: 378px;" %)**Connector exterior**|=(% style="text-align: center; vertical-align: middle; width: 337px;" %)**terminal pin distribution**|=(% style="text-align: center; vertical-align: middle; width: 94px;" %)**Motor flange**
226 |=(% style="text-align: center; vertical-align: middle; width: 131px;" %)WD series|(% style="text-align:center; vertical-align:middle; width:239px" %)[[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9be5695e6c0fd897.gif||height="119" width="149"]]|(% style="width:337px" %)(((
227 (% class="table-bordered" style="width:285px" %)
228 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 131px;" %)**Signal name**
229 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle; width:131px" %)BR+
230 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle; width:131px" %)BR-
231 )))|(% style="text-align:center; vertical-align:middle; width:94px" %)(((
232 40
233
234 60
235
236 80
237 )))
238 |=(% scope="col" style="text-align: center; vertical-align: middle; width: 131px;" %)WE series|(% style="text-align:center; vertical-align:middle; width:239px" %)[[image:image-20220611124106-5.png||height="123" width="134"]]|(% style="width:337px" %)(((
239 (% class="table-bordered" style="width:284px" %)
240 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)**Signal name**
241 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle; width:128px" %)DC 24V
242 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle; width:128px" %)GND
243 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle; width:128px" %)-
244 )))|(% style="text-align:center; vertical-align:middle; width:94px" %)(((
245 80
246
247 110
248
249 130
250 )))
251
252 Table 4-5 Brake device cable
253
254 == **Encoder cable connection** ==
255
256 (% class="box infomessage" %)
257 (((
258 ✎ **Note: **It is recommended that the encoder cable should not exceed 10m, otherwise it may cause an error **A93.**
259 )))
260
261 (% style="text-align:center" %)
262 (((
263 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
264 [[**Figure 4-8 Encoder connection line wiring**>>image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_2a7019b4f21f159e.gif||height="324" id="IWeconVD2SASeriesServoDrivesManual28FullV1.129_html_2a7019b4f21f159e.gif" width="857"]]
265 )))
266
267
268 (% class="table-bordered" %)
269 |=(% style="text-align: center; vertical-align: middle;" %)**Connector exterior**|=(% style="text-align: center; vertical-align: middle;" %)**Terminal pin distribution**|=(% style="text-align: center; vertical-align: middle;" %)**Pin description**
270 |(% style="text-align:center; vertical-align:middle" %)[[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_c798aa1eac035779.gif||height="106" width="76"]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220611155405-4.png]]|(((
271 (% class="table-bordered" %)
272 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**
273 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)-
274 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+
275 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-
276 )))
277
278 Table 4-6 Encoder cable servo drive side connector
279
280 (% class="table-bordered" %)
281 |=(% colspan="2" style="text-align: center; vertical-align: middle;" %)**Connector exterior and terminal pin distribution**|=(% style="text-align: center; vertical-align: middle;" %)**Motor flange**
282 |(% style="text-align:center; vertical-align:middle" %)(((
283 (% style="text-align:center" %)
284 [[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_a41c00ba1133ea20.png||height="145" width="502"]]
285
286
287 )))|(((
288 (% style="text-align:center" %)
289 [[image:image-20220608142110-6.png||height="182" width="278"]]
290 )))|(% rowspan="3" style="text-align:center; vertical-align:middle" %)(((
291 40
292
293 60
294
295 80
296 )))
297 |(% style="text-align:center; vertical-align:middle" %)(((
298 (% style="text-align:center" %)
299 [[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_1ce0548bf47ef5ae.gif]]
300 )))|(((
301 (% style="text-align:center" %)
302 [[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_4cb7be8f7bd5893e.gif]]
303 )))
304 |(% colspan="2" %)(((
305 (% class="table-bordered" style="margin-left:auto; margin-right:auto; width:622px" %)
306 |=(% style="text-align: center; vertical-align: middle; width: 289px;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 329px;" %)**Signal name**
307 |(% style="text-align:center; vertical-align:middle; width:289px" %)7|(% style="text-align:center; vertical-align:middle; width:329px" %)5V
308 |(% style="text-align:center; vertical-align:middle; width:289px" %)8|(% style="text-align:center; vertical-align:middle; width:329px" %)GND
309 |(% style="text-align:center; vertical-align:middle; width:289px" %)4|(% style="text-align:center; vertical-align:middle; width:329px" %)SD+
310 |(% style="text-align:center; vertical-align:middle; width:289px" %)5|(% style="text-align:center; vertical-align:middle; width:329px" %)SD-
311 |(% style="text-align:center; vertical-align:middle; width:289px" %)3|(% style="text-align:center; vertical-align:middle; width:329px" %)Shield
312 |(% style="text-align:center; vertical-align:middle; width:289px" %)1|(% style="text-align:center; vertical-align:middle; width:329px" %)Battery+
313 |(% style="text-align:center; vertical-align:middle; width:289px" %)2|(% style="text-align:center; vertical-align:middle; width:329px" %)Battery-
314 )))
315
316 Table 4-7 Absolute value encoder line connector (Rectangular plug)
317
318 (% class="table-bordered" %)
319 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle" %)**Motor side**
320 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Rectangular plug pin number**|(% style="text-align:center; vertical-align:middle" %)**Cable color**
321 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Blue
322 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Encoder power ground|(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Orange
323 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+|(% style="text-align:center; vertical-align:middle" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Green
324 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-|(% style="text-align:center; vertical-align:middle" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Brown
325 |(% style="text-align:center; vertical-align:middle" %)Shell|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)~-~-
326 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery+|(% style="text-align:center; vertical-align:middle" %)1*|(% style="text-align:center; vertical-align:middle" %)Pink
327 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery-|(% style="text-align:center; vertical-align:middle" %)2*|(% style="text-align:center; vertical-align:middle" %)Pink-Black
328
329 Table 4-8 Connection of encoder line pin
330
331 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
332
333 [[image:企业微信截图_16606338254815.png]]
334
335 (% class="box infomessage" %)
336 (((
337 ✎ **Note: **The color of the line is subject to the actual product. The lines described in this manual are all lines of Wecon!
338 )))
339
340 (% class="table-bordered" %)
341 |(% colspan="2" style="text-align:center; vertical-align:middle; width:937px" %)**Connector shape and terminal pin distribution**|(% style="text-align:center; vertical-align:middle; width:138px" %)**Motor flange**
342 |(% style="text-align:center; vertical-align:middle; width:531px" %)(((
343 (% style="text-align:center" %)
344 [[image:Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_d450a92cc1507fcd.png||height="178" width="487"]]
345 )))|(% style="text-align:center; vertical-align:middle; width:428px" %)[[image:image-20220608142557-7.png]]|(% rowspan="3" style="text-align:center; vertical-align:middle; width:138px" %)(((
346 110
347
348 130
349 )))
350 |(% style="width:531px" %)(((
351 (% style="text-align:center" %)
352 [[image:image-20220608144304-1.png]]
353 )))|(% style="width:428px" %)(((
354 (% style="text-align:center" %)
355 [[image:image-20220608144357-2.png]]
356 )))
357 |(% colspan="2" style="width:937px" %)(((
358 (% style="margin-left:auto; margin-right:auto; width:535px" %)
359 |=(% style="text-align: center; vertical-align: middle; width: 262px;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 271px;" %)**Signal name**
360 |(% style="text-align:center; vertical-align:middle; width:262px" %)7|(% style="text-align:center; vertical-align:middle; width:271px" %)5V
361 |(% style="text-align:center; vertical-align:middle; width:262px" %)5|(% style="text-align:center; vertical-align:middle; width:271px" %)GND
362 |(% style="text-align:center; vertical-align:middle; width:262px" %)6|(% style="text-align:center; vertical-align:middle; width:271px" %)SD+
363 |(% style="text-align:center; vertical-align:middle; width:262px" %)4|(% style="text-align:center; vertical-align:middle; width:271px" %)SD-
364 |(% style="text-align:center; vertical-align:middle; width:262px" %)1|(% style="text-align:center; vertical-align:middle; width:271px" %)Shield
365 |(% style="text-align:center; vertical-align:middle; width:262px" %)3|(% style="text-align:center; vertical-align:middle; width:271px" %)Battery+
366 |(% style="text-align:center; vertical-align:middle; width:262px" %)2|(% style="text-align:center; vertical-align:middle; width:271px" %)Battery-
367 )))
368
369 Table 4-9 Absolute value encoder line connector (Aviation plug)
370
371 (% class="table-bordered" %)
372 |=(% colspan="2" style="text-align: center; vertical-align: middle; width: 258px;" %)**Drive side J1394**|=(% rowspan="2" style="text-align: center; vertical-align: middle; width: 273px;" %)**Description**|=(% colspan="2" style="text-align: center; vertical-align: middle; width: 365px;" %)**Motor side**
373 |=(% style="text-align: center; vertical-align: middle; width: 126px;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle; width: 218px;" %)(((
374 **Aviation plug pin number**
375 )))|=(% style="text-align: center; vertical-align: middle; width: 156px;" %)**Cable color**
376 |(% style="text-align:center; vertical-align:middle; width:126px" %)1|(% style="text-align:center; vertical-align:middle; width:128px" %)5V|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle; width:218px" %)7|(% style="text-align:center; vertical-align:middle; width:156px" %)Blue
377 |(% style="text-align:center; vertical-align:middle; width:126px" %)2|(% style="text-align:center; vertical-align:middle; width:128px" %)GND|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder power ground|(% style="text-align:center; vertical-align:middle; width:218px" %)5|(% style="text-align:center; vertical-align:middle; width:156px" %)Orange
378 |(% style="text-align:center; vertical-align:middle; width:126px" %)5|(% style="text-align:center; vertical-align:middle; width:128px" %)SD+|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle; width:218px" %)6|(% style="text-align:center; vertical-align:middle; width:156px" %)Green
379 |(% style="text-align:center; vertical-align:middle; width:126px" %)6|(% style="text-align:center; vertical-align:middle; width:128px" %)SD-|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle; width:218px" %)4|(% style="text-align:center; vertical-align:middle; width:156px" %)Brown
380 |(% style="text-align:center; vertical-align:middle; width:126px" %)Shell|(% style="text-align:center; vertical-align:middle; width:128px" %)Shield|(% style="text-align:center; vertical-align:middle; width:273px" %)Shield|(% style="text-align:center; vertical-align:middle; width:218px" %)1|(% style="text-align:center; vertical-align:middle; width:156px" %)-
381 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery+|(% style="text-align:center; vertical-align:middle; width:218px" %)3*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink
382 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery-|(% style="text-align:center; vertical-align:middle; width:218px" %)2*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink-Black
383
384 Table 4-10 Absolute encoder cable connector (aviation socket)
385
386 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
387
388 (% class="box infomessage" %)
389 (((
390 ✎ **Note: **The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
391 )))
392
393 (% class="table-bordered" %)
394 |=(% colspan="2" style="text-align: center; vertical-align: middle; width: 667px;" %)**Connector shape and terminal pin distribution**|=(% style="text-align: center; vertical-align: middle; width: 107px;" %)(((
395 **Motor**
396
397 **flange**
398 )))
399 |(% style="text-align:center; vertical-align:middle; width:380px" %)(((
400 (% style="text-align:center" %)
401 [[image:image-20220608144543-3.png||height="130" width="317"]]
402 )))|(% style="width:320px" %)(((
403 (% style="text-align:center" %)
404 [[image:image-20220608144728-6.png||height="187" width="210"]]
405 )))|(% rowspan="3" style="text-align:center; vertical-align:middle; width:107px" %)(((
406 60
407
408 80
409 )))
410 |(% style="text-align:center; vertical-align:middle; width:380px" %)(((
411 (% style="text-align:center" %)
412 [[image:image-20220608144619-5.png||height="132" width="316"]]
413 )))|(% style="width:320px" %)(((
414 (% style="text-align:center" %)
415 [[image:image-20220608144750-7.png||height="137" width="358"]]
416 )))
417 |(% colspan="2" style="width:667px" %)(((
418 (% class="table-bordered" style="margin-left:auto; margin-right:auto; width:605px" %)
419 |=(% style="text-align: center; vertical-align: middle; width: 295px;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 309px;" %)**Signal name**
420 |(% style="text-align:center; vertical-align:middle; width:295px" %)7|(% style="text-align:center; vertical-align:middle; width:309px" %)5V
421 |(% style="text-align:center; vertical-align:middle; width:295px" %)5|(% style="text-align:center; vertical-align:middle; width:309px" %)GND
422 |(% style="text-align:center; vertical-align:middle; width:295px" %)6|(% style="text-align:center; vertical-align:middle; width:309px" %)SD+
423 |(% style="text-align:center; vertical-align:middle; width:295px" %)4|(% style="text-align:center; vertical-align:middle; width:309px" %)SD-
424 |(% style="text-align:center; vertical-align:middle; width:295px" %)1|(% style="text-align:center; vertical-align:middle; width:309px" %)Shield
425 |(% style="text-align:center; vertical-align:middle; width:295px" %)3|(% style="text-align:center; vertical-align:middle; width:309px" %)Battery+
426 |(% style="text-align:center; vertical-align:middle; width:295px" %)2|(% style="text-align:center; vertical-align:middle; width:309px" %)Battery-
427 )))
428
429 Table 4-11 Absolute encoder cable connector (in-line type)
430
431 (% class="table-bordered" %)
432 |=(% colspan="2" style="text-align: center; vertical-align: middle; width: 218px;" %)**Drive side J1394**|=(% rowspan="2" style="text-align: center; vertical-align: middle; width: 242px;" %)**Description**|=(% colspan="2" style="text-align: center; vertical-align: middle; width: 311px;" %)**Motor side**
433 |=(% style="text-align: center; vertical-align: middle; width: 100px;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle; width: 117px;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle; width: 188px;" %)(((
434 **In-line plug pin number**
435 )))|=(% style="text-align: center; vertical-align: middle; width: 128px;" %)**Cable color**
436 |(% style="text-align:center; vertical-align:middle; width:100px" %)1|(% style="text-align:center; vertical-align:middle; width:117px" %)5V|(% style="text-align:center; vertical-align:middle; width:242px" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle; width:188px" %)7|(% style="text-align:center; vertical-align:middle; width:128px" %)Blue
437 |(% style="text-align:center; vertical-align:middle; width:100px" %)2|(% style="text-align:center; vertical-align:middle; width:117px" %)GND|(% style="text-align:center; vertical-align:middle; width:242px" %)Encoder power ground|(% style="text-align:center; vertical-align:middle; width:188px" %)5|(% style="text-align:center; vertical-align:middle; width:128px" %)Orange
438 |(% style="text-align:center; vertical-align:middle; width:100px" %)5|(% style="text-align:center; vertical-align:middle; width:117px" %)SD+|(% style="text-align:center; vertical-align:middle; width:242px" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle; width:188px" %)6|(% style="text-align:center; vertical-align:middle; width:128px" %)Green
439 |(% style="text-align:center; vertical-align:middle; width:100px" %)6|(% style="text-align:center; vertical-align:middle; width:117px" %)SD-|(% style="text-align:center; vertical-align:middle; width:242px" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle; width:188px" %)4|(% style="text-align:center; vertical-align:middle; width:128px" %)Brown
440 |(% style="text-align:center; vertical-align:middle; width:100px" %)Shell|(% style="text-align:center; vertical-align:middle; width:117px" %)Shield|(% style="text-align:center; vertical-align:middle; width:242px" %)Shield|(% style="text-align:center; vertical-align:middle; width:188px" %)1|(% style="text-align:center; vertical-align:middle; width:128px" %)-
441 |(% style="text-align:center; vertical-align:middle; width:100px" %)-|(% style="text-align:center; vertical-align:middle; width:117px" %)-|(% style="text-align:center; vertical-align:middle; width:242px" %)Battery+|(% style="text-align:center; vertical-align:middle; width:188px" %)3*|(% style="text-align:center; vertical-align:middle; width:128px" %)Brown
442 |(% style="text-align:center; vertical-align:middle; width:100px" %)-|(% style="text-align:center; vertical-align:middle; width:117px" %)-|(% style="text-align:center; vertical-align:middle; width:242px" %)Battery-|(% style="text-align:center; vertical-align:middle; width:188px" %)2*|(% style="text-align:center; vertical-align:middle; width:128px" %)Black
443
444 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
445
446 (% class="box infomessage" %)
447 (((
448 ✎**Note:** The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
449 )))
450
451 = **Servo drive control input and output wiring** =
452
453 == CN2 pin distribution ==
454
455 **VD2A and VD2B servo drive control input and output pin distribution (CN2 interface)**
456
457 [[image:企业微信截图_16841152769709.png||height="800" width="500"]]
458
459 (% style="text-align:center" %)
460 (((
461 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
462 [[**Figure 4-9 VD2A and VD2B servo drive control input and output pin distribution**>>image:企业微信截图_16841152769709.png||height="800" id="企业微信截图_16841152769709.png" width="500"]]
463 )))
464
465 (% style="text-align:center" %)
466 (((
467 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
468 [[**Figure 4-9 VD2A and VD2B servo drive control input and output pin distribution**>>image:image-20220824105322-3.jpeg||height="735" id="Iimage-20220824105322-3.jpeg" width="165"]]
469 )))
470
471 (% class="table-bordered" %)
472 |=(% scope="row" style="text-align: center; vertical-align: middle;" %)**Pin number**|=**Signal name**|=**Pin number**|=**Signal name**|=**Pin number**|=**Signal name**
473 |=1|-|16|GND|31|-
474 |=2|AI_2+|17|GND|32|AI_1+
475 |=3|AI_2-|18|-|33|AI_1-
476 |=4|DO1-|19|DO3-|34|GND
477 |=5|DO1+|20|DO3+|35|-
478 |=6|DO2-|21|DO4-|36|-
479 |=7|DO2+|22|DO4+|37|-
480 |=8|SS|23|DI5|38|-
481 |=9|DI1|24|DI6|39|-
482 |=10|DI2|25|DI7|40|SIGN-
483 |=11|DI3|26|DI8|41|SIGN+
484 |=12|DI4|27|GND|42|PULS-
485 |=13|PAO-|28|PAO+|43|PULS+
486 |=14|PBO-|29|PBO+|44|PL
487 |=15|PZO-|30|PZO+|~-~-|~-~-
488
489 Table 4-12 CN2 interface definition of VD2A and VD2B servo drive
490
491 **VD2F servo drive control input and output pin distribution (CN2 interface)**
492
493 (% style="text-align:center" %)
494 (((
495 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
496 [[**Figure 4-10 VD2F servo drive control input and output pin distribution**>>image:image-20220824105128-1.jpeg||height="463" id="Iimage-20220824105128-1.jpeg" width="159"]]
497 )))
498
499 |=**Pin number**|=**Signal name**|=**Pin number**|=**Signal name**|=**Pin number**|=**Signal name**
500 |1|DO3|6|DO4|11|PL
501 |2|DO1|7|DO2|12|PULS+
502 |3|SS|8|DOCOM|13|PULS-
503 |4|DI3|9|DI4|14|SIGN+
504 |5|DI1|10|DI2|15|SIGN-
505
506 Table 4-13 CN2 interface definition of VD2F servo drive
507
508 == Wiring diagram ==
509
510 **VD2A and VD2B servo drive**
511
512 (% style="text-align:center" %)
513 (((
514 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
515 [[**Figure 4-11 Wiring diagram of each mode**>>image:4-11.jpg||height="961" id="I4-11.jpg" width="750"]]
516 )))
517
518 (% class="box infomessage" %)
519 (((
520 ✎**Note:** Please refer to "Table 4-13 CN2 interface definition of VD2A and VD2B servo drive" for the pin numbers in the figure.
521 )))
522
523 **VD2F servo drive**
524
525 (% style="text-align:center" %)
526 (((
527 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
528 [[**Figure 4-12 Position pulse mode wiring**>>image:image-20220608145058-9.png||id="Iimage-20220608145058-9.png"]]
529 )))
530
531 (% class="box infomessage" %)
532 (((
533 ✎**Note:** Please refer to "Table 4-14 CN2 interface definition of VD2F servo drive" for the pin numbers in the figure.
534 )))
535
536 == Position instruction input signal ==
537
538 (% class="table-bordered" %)
539 |=(% style="text-align: center; vertical-align: middle; width: 128px;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle; width: 160px;" %)**VD2A and VD2B pin number**|=(% style="text-align: center; vertical-align: middle; width: 129px;" %)**VD2F pin number**|=(% style="text-align: center; vertical-align: middle; width: 357px;" %)**Function**
540 |(% style="text-align:center; vertical-align:middle; width:128px" %)PULS+|(% style="text-align:center; vertical-align:middle; width:160px" %)43|(% style="text-align:center; vertical-align:middle; width:129px" %)12|(% rowspan="4" style="width:357px" %)(((
541 Low-speed pulse input modes: differential input, open collector.
542
543 There are three types of input pulse:
544
545 1. Direction + pulse (positive logic);
546 1. CW/CCW;
547 1. A and B phase quadrature pulses (4 times the frequency).
548 )))
549 |(% style="text-align:center; vertical-align:middle; width:128px" %)PULS-|(% style="text-align:center; vertical-align:middle; width:160px" %)42|(% style="text-align:center; vertical-align:middle; width:129px" %)13
550 |(% style="text-align:center; vertical-align:middle; width:128px" %)SIGN+|(% style="text-align:center; vertical-align:middle; width:160px" %)41|(% style="text-align:center; vertical-align:middle; width:129px" %)14
551 |(% style="text-align:center; vertical-align:middle; width:128px" %)SIGN-|(% style="text-align:center; vertical-align:middle; width:160px" %)40|(% style="text-align:center; vertical-align:middle; width:129px" %)15
552 |(% style="text-align:center; vertical-align:middle; width:128px" %)PL|(% style="text-align:center; vertical-align:middle; width:160px" %)44|(% style="text-align:center; vertical-align:middle; width:129px" %)11|(% style="width:357px" %)External power input interface for instruction pulse.
553
554 Table 4-14 Position instruction signal description
555
556 The instruction pulse and sign output circuit on the host device side can be selected from differential output or open collector output. The maximum input frequency is shown in the table.
557
558 (% class="table-bordered" %)
559 |=(% style="text-align: center; vertical-align: middle;" %)**Pulse method**|=(% style="text-align: center; vertical-align: middle;" %)**Difference**|=(% style="text-align: center; vertical-align: middle;" %)**Open collector**
560 |(% style="text-align:center; vertical-align:middle" %)Maximum frequency|(% style="text-align:center; vertical-align:middle" %)500KHz|(% style="text-align:center; vertical-align:middle" %)200KHz
561
562 **Differential input**
563
564 The connection of differential input is shown in Figure 4-9
565
566 (% style="text-align:center" %)
567 (((
568 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
569 [[**Figure 4-13 VD2A and VD2B servo drive differential input connection**>>image:image-20220610140653-1.png||id="Iimage-20220610140653-1.png"]]
570 )))
571
572 (% style="text-align:center" %)
573 (((
574 (% class="wikigeneratedid" style="display:inline-block" %)
575 [[**Figure 4-14 VD2F servo drive differential input connection**>>image:image-20220706104653-3.jpeg||id="Iimage-20220706104653-3.jpeg"]]
576 )))
577
578 **Open collector input**
579
580 * Open collector input connection
581
582 (% style="text-align:center" %)
583 (((
584 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
585 [[**Figure 4-15 VD2A and VD2B servo drive open collector input connection**>>image:image-20220706104705-4.jpeg||height="638" id="Iimage-20220706104705-4.jpeg" width="881"]]
586 )))
587
588 (% style="text-align:center" %)
589 (((
590 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
591 [[**Figure 4-16 VD2F servo drive open collector input connection**>>image:image-20220706104712-5.jpeg||height="628" id="Iimage-20220706104712-5.jpeg" width="875"]]
592 )))
593
594 * NPN and PNP wiring
595
596 (% class="table-bordered" %)
597 |(% style="width:597px" %)(((
598 (((
599 (% style="text-align:center" %)
600 [[image:image-20220706104746-7.jpeg||class="img-thumbnail"]]
601 )))
602 )))|(% style="width:478px" %)(((
603 (((
604 (% style="text-align:center" %)
605 [[image:image-20220706104753-8.jpeg||class="img-thumbnail"]]
606 )))
607 )))
608 |(% style="text-align:center; vertical-align:middle; width:597px" %)NPN|(% style="text-align:center; vertical-align:middle; width:478px" %)PNP
609 |(% colspan="2" style="text-align:center; vertical-align:middle" %)Figure 4-17 Triode Wiring
610
611 == **Analog input signal** ==
612
613 The analog input signal is only supported by VD2A and VD2B servo drives.
614
615 (% class="table-bordered" %)
616 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Function**
617 |(% style="text-align:center; vertical-align:middle" %)32|(% style="text-align:center; vertical-align:middle" %)AI_1+|(% rowspan="2" %)(((
618 AI_1 analog input signal, resolution 12-bit.
619
620 Input voltage range: -10V to +10V.
621 )))
622 |(% style="text-align:center; vertical-align:middle" %)33|(% style="text-align:center; vertical-align:middle" %)AI_1-
623 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)AI_2+|(% rowspan="2" %)(((
624 AI_2 analog input signal, resolution 12-bit.
625
626 Input voltage range: -10V to +10V.
627 )))
628 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)AI_2-
629 |(% style="text-align:center; vertical-align:middle" %)17|(% style="text-align:center; vertical-align:middle" %)GND|(% rowspan="2" %)Analog input signal ground.
630 |(% style="text-align:center; vertical-align:middle" %)34|(% style="text-align:center; vertical-align:middle" %)GND
631
632 Table 4-15 Analog input signal description
633
634 (% style="text-align:center" %)
635 (((
636 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
637 [[**Figure 4-18 Analog input wiring**>>image:image-20220611152916-3.jpeg||height="295" id="Iimage-20220611152916-3.jpeg" width="504"]]
638 )))
639
640
641 == Digital input&output signals ==
642
643 **VD2A and VD2B servo drives**
644
645 (% class="table-bordered" %)
646 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Signal name**|=(% style="text-align: center; vertical-align: middle;" %)**Default function**
647 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
648 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
649 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
650 |(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
651 |(% style="text-align:center; vertical-align:middle" %)23|(% style="text-align:center; vertical-align:middle" %)DI5|(% style="text-align:center; vertical-align:middle" %)Inverted instruction
652 |(% style="text-align:center; vertical-align:middle" %)24|(% style="text-align:center; vertical-align:middle" %)DI6|(% style="text-align:center; vertical-align:middle" %)Instruction pulse prohibited input
653 |(% style="text-align:center; vertical-align:middle" %)25|(% style="text-align:center; vertical-align:middle" %)DI7|(% style="text-align:center; vertical-align:middle" %)Not used
654 |(% style="text-align:center; vertical-align:middle" %)26|(% style="text-align:center; vertical-align:middle" %)DI8|(% style="text-align:center; vertical-align:middle" %)Not used
655 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)24V
656 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DO1-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Rotation detection
657 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DO1+
658 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO2-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Faults signal
659 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2+
660 |(% style="text-align:center; vertical-align:middle" %)19|(% style="text-align:center; vertical-align:middle" %)DO3-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Servo is ready
661 |(% style="text-align:center; vertical-align:middle" %)20|(% style="text-align:center; vertical-align:middle" %)DO3+
662 |(% style="text-align:center; vertical-align:middle" %)21|(% style="text-align:center; vertical-align:middle" %)DO4-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Positioning completed
663 |(% style="text-align:center; vertical-align:middle" %)22|(% style="text-align:center; vertical-align:middle" %)DO4+
664
665 Table 4-16 DI/DO signal description
666
667 **Digital input circuit**
668
669 * When the control device (HMI/PLC) is relay output
670
671 (% style="text-align:center" %)
672 (((
673 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
674 [[**Figure 4-19 Relay output**>>image:image-20220706104845-9.jpeg||height="425" id="Iimage-20220706104845-9.jpeg" width="352"]]
675 )))
676
677 * When the control device (HMI/PLC) is open collector output
678
679 (% style="text-align:center" %)
680 (((
681 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
682 [[**Figure 4-20 Open collector output**>>image:image-20220706104858-10.jpeg||height="487" id="Iimage-20220706104858-10.jpeg" width="352"]]
683 )))
684
685 **Digital output circuit**
686
687 * When the control device (HMI/PLC) is relay input
688
689 (% style="text-align:center" %)
690 (((
691 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
692 [[**Figure 4-21 Relay input**>>image:image-20220611153124-4.jpeg||height="567" id="Iimage-20220611153124-4.jpeg" width="352"]]
693 )))
694
695 * When the control device (HMI/PLC) is optocoupler input
696
697 (% style="text-align:center" %)
698 (((
699 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
700 [[**Figure 4-22 Optocoupler input**>>image:image-20220611153802-10.jpeg||height="485" id="Iimage-20220611153802-10.jpeg" width="352"]]
701 )))
702
703 **VD2F servo drive**
704
705 (% class="table-bordered" %)
706 |=(% style="text-align: center; vertical-align: middle;" %)**Pin number**|=(% style="text-align: center; vertical-align: middle;" %)**Pin name**|=(% style="text-align: center; vertical-align: middle;" %)**Default function**
707 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
708 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
709 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
710 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
711 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)24V
712 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)DO1|(% style="text-align:center; vertical-align:middle" %)Rotation detection
713 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2|(% style="text-align:center; vertical-align:middle" %)Fault signal
714 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DO3|(% style="text-align:center; vertical-align:middle" %)Servo is ready
715 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO4|(% style="text-align:center; vertical-align:middle" %)Positioning completed
716 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DOCOM|(% style="text-align:center; vertical-align:middle" %)Do common terminal
717
718 Table 4-17 DI/DO signal description
719
720 **Digital input circuit**
721
722 * When the control device (HMI/PLC) is relay output
723
724 (% style="text-align:center" %)
725 (((
726 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
727 [[**Figure 4-23 Relay output**>>image:image-20220706105605-11.jpeg||height="429" id="Iimage-20220706105605-11.jpeg" width="352"]]
728 )))
729
730 * When the control device (HMI/PLC) is open collector output
731
732 (% style="text-align:center" %)
733 (((
734 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
735 [[**Figure 4-24 Open collector output**>>image:image-20220706110028-12.jpeg||height="476" id="Iimage-20220706110028-12.jpeg" width="352"]]
736 )))
737
738 **Digital output circuit**
739
740 * When the control device (HMI/PLC) is relay input
741
742 (% style="text-align:center" %)
743 (((
744 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
745 [[**Figure 4-25 Relay output**>>image:image-20220611154302-14.jpeg||height="494" id="Iimage-20220611154302-14.jpeg" width="352"]]
746 )))
747
748 * When the control device (HMI/PLC) is optocoupler input
749
750 (% style="text-align:center" %)
751 (((
752 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
753 [[**Figure 4-26 Optocoupler input**>>image:image-20220611154225-13.jpeg||height="473" id="Iimage-20220611154225-13.jpeg" width="352"]]
754 )))
755
756 == Brake wiring ==
757
758 The brake is a mechanism that prevents the servo motor shaft from moving when the servo drive is in a non-running state, so that the motor remains in position lock, so that the moving part of the machinery will not move due to self-weight or external force.
759
760 Brake input signal is no polar. You need to use 24V power . The standard wiring between brake signal BK and brake power is as below.
761
762 (% style="text-align:center" %)
763 (((
764 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
765 [[**Figure 4-27 Brake wiring of VD2A and VD2B**>>image:image-20220611153503-7.jpeg||id="Iimage-20220611153503-7.jpeg"]]
766 )))
767
768 (% style="text-align:center" %)
769 (((
770 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
771 [[**Figure 4-28 Brake wiring of VD2F**>>image:image-20220611153514-8.jpeg||id="Iimage-20220611153514-8.jpeg"]]
772 )))
773
774 == Communication signal wiring ==
775
776 Wecon VD2 series servo drive supports two communication modes: RS-422 and RS-485. The communication port is RJ45 socket. The exterior of communication terminal is shown in Figure 4-31
777
778 (% style="text-align:center" %)
779 (((
780 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
781 [[**Figure 4-31 Pin number of an RJ45 socket**>>image:image-20220706114233-13.png||id="Iimage-20220706114233-13.png"]]
782 )))
783
784 The communication modes supported by the driver communication ports are in the following table.
785
786 |=(% colspan="2" style="width: 412px;" %)**VD2 A&VD2 B**|=(% colspan="2" style="width: 663px;" %)**VD2F**
787 |(% style="width:80px" %)**Port**|(% style="width:223px" %)**Communication mode**|(% style="width:95px" %)**Port**|(% style="width:359px" %)**Communication mode**
788 |(% style="width:80px" %)CN3|(% style="width:223px" %)Only RS422|(% style="width:95px" %)CN3|(% rowspan="2" style="width:359px" %)RS422, RS485 communication mode choose one of two. Set by function code P12-05
789 |(% style="width:80px" %)CN5|(% rowspan="2" style="width:223px" %)Only RS485|(% style="width:95px" %)CN4
790 |(% style="width:80px" %)CN6|(% colspan="2" rowspan="2" style="width:663px" %)**✎Note**: The CN3 and CN4 interfaces are physically connected and are actually the same communication interface. When P12-05 is set to 1, CN3 and CN4 use RS485 communication mode. If the value is set to 0, both use RS422 communication mode.
791 |(% colspan="2" style="width:412px" %)**✎Note**: The CN5 and CN6 interfaces are physically connected and are actually the same communication interface.
792
793 Table 4-19 Communication port communication modes
794
795 **Communication connection with servo host computer (RS422)**
796
797 Servo drives communicate with the host computer via RS422 communication. A USB to RS422 (RJ45 connector) cable is required for communication, and you need to equip it by yourselves.
798
799 * **VD2A&VD2B**
800
801 VD2A and VD2B servo drives communicate with the host computer via the CN3 interface by RS422 communication. Figure 4-32 and Figure 4-33 show the communication connections.
802
803 (% style="text-align:center" %)
804 (((
805 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
806 [[**Figure 4-32 The Connection between VD2A drive and PC**>>image:企业微信截图_16775647177614.png||alt="image-20220706114358-14.png" id="Iimage-20220706114358-14.png"]]
807 )))
808
809 (% style="text-align:center" %)
810 (((
811 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
812 [[**Figure 4-33 The connection between VD2B drive and PC**>>image:企业微信截图_16775652329416.png||alt="image-20220706114416-15.png" id="Iimage-20220706114416-15.png"]]
813 )))
814
815 |=(% style="width: 170px;" %)**CN3**|=(% style="width: 97px;" %)**Pin**|=(% style="width: 105px;" %)**Name**|=(% style="width: 403px;" %)**Function description**
816 |(% rowspan="8" style="width:170px" %)(((
817 [[image:image-20220706114749-4.png||height="163" width="149"]]
818 )))|(% style="width:97px" %)1|(% style="width:105px" %)RX-|(% style="width:403px" %)Computer sends negative terminal (drive receives negative)
819 |(% style="width:97px" %)2|(% style="width:105px" %)RX+|(% style="width:403px" %)Computer sends positive terminal (drive receives positive)
820 |(% style="width:97px" %)3|(% style="width:105px" %)TX-|(% style="width:403px" %)Computer receives negative terminal (drive sends negative)
821 |(% style="width:97px" %)4|(% style="width:105px" %)GND|(% style="width:403px" %)Ground terminal
822 |(% style="width:97px" %)5|(% style="width:105px" %)NC|(% style="width:403px" %)Not used
823 |(% style="width:97px" %)6|(% style="width:105px" %)TX+|(% style="width:403px" %)Computer receives positive terminal (drive sends positive)
824 |(% style="width:97px" %)7|(% style="width:105px" %)NC|(% style="width:403px" %)Not used
825 |(% style="width:97px" %)8|(% style="width:105px" %)NC|(% style="width:403px" %)Not used
826
827 Table 4-20 VD2A and VD2B pin definitions for CN3
828
829 * **VD2F**
830
831 VD2F servo drive communicates with the host computer via the CN3 or CN4 interface byRS422 communication. The communication diagrams of VD2F servo drive and host computer are shown in Figure 4-34.
832
833 (% style="text-align:center" %)
834 (((
835 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
836 [[**Figure 4-34 The connection between VD2F drive and PC**>>image:image-20220706114622-16.png||id="Iimage-20220706114622-16.png"]]
837 )))
838
839 |=(% style="width: 162px;" %)**CN3&CN4**|=(% style="width: 87px;" %)**Pin**|=(% style="width: 106px;" %)**Name**|=(% style="width: 420px;" %)**Function description**
840 |(% rowspan="8" style="width:162px" %)[[image:image-20220706114745-3.png||height="142" width="129"]]|(% style="width:87px" %)1|(% style="width:106px" %)RX-|(% style="width:420px" %)Computer sends negative terminal (drive receives negative)
841 |(% style="width:87px" %)2|(% style="width:106px" %)RX+|(% style="width:420px" %)Computer sends positive terminal (drive receives positive)
842 |(% style="width:87px" %)3|(% style="width:106px" %)TX-|(% style="width:420px" %)Computer receives negative terminal (drive sends negative)
843 |(% style="width:87px" %)4|(% style="width:106px" %)GND|(% style="width:420px" %)Ground terminal
844 |(% style="width:87px" %)5|(% style="width:106px" %)NC|(% style="width:420px" %)Not used
845 |(% style="width:87px" %)6|(% style="width:106px" %)TX+|(% style="width:420px" %)Computer receives positive terminal (drive sends positive)
846 |(% style="width:87px" %)7|(% style="width:106px" %)NC|(% style="width:420px" %)Not used
847 |(% style="width:87px" %)8|(% style="width:106px" %)NC|(% style="width:420px" %)Not used
848
849 Table 4-21 VD2F pin definitions for CN3 and CN4 interfaces
850
851 **Communication connection with PLC and other device (RS485)**
852
853 VD2A and VD2B servo drives communicate with PLC and other devices for Modbus via CN5 or CN6 interface (located on the top of servo drive) by RS485 communication.
854
855 |=(% style="width: 166px;" %)**CN5&CN6**|=(% style="width: 81px;" %)**Pin**|=(% style="width: 109px;" %)**Name**|=(% style="width: 435px;" %)**Function description**
856 |(% rowspan="8" style="width:166px" %)[[image:image-20220706114742-2.png||height="146" width="133"]]|(% style="width:81px" %)1|(% style="width:109px" %)485-|(% style="width:435px" %)Computer sends negative terminal (drive receives negative)
857 |(% style="width:81px" %)2|(% style="width:109px" %)485+|(% style="width:435px" %)Computer sends positive terminal (drive receives positive)
858 |(% style="width:81px" %)3|(% style="width:109px" %)NC|(% style="width:435px" %)Not used
859 |(% style="width:81px" %)4|(% style="width:109px" %)GND|(% style="width:435px" %)Ground terminal
860 |(% style="width:81px" %)5|(% style="width:109px" %)GND|(% style="width:435px" %)Ground terminal
861 |(% style="width:81px" %)6|(% style="width:109px" %)NC|(% style="width:435px" %)Not used
862 |(% style="width:81px" %)7|(% style="width:109px" %)Reserved|(% style="width:435px" %)Reserved
863 |(% style="width:81px" %)8|(% style="width:109px" %)GND|(% style="width:435px" %)Ground terminal
864
865 Table 4-22 The pin definition of CN5/CN6 interface
866
867 VD2F servo drives communicate with PLC and other devices for Modbus via CN3 or CN4 interface (located on the top of servo drive) by RS485 communication.
868
869 |=(% style="width: 165px;" %)**CN3&CN4**|=(% style="width: 90px;" %)**Pin**|=(% style="width: 102px;" %)**Name**|=(% style="width: 418px;" %)**Function description**
870 |(% rowspan="8" style="width:165px" %)[[image:image-20220706114737-1.png||height="151" width="138"]]|(% style="width:90px" %)1|(% style="width:102px" %)485-|(% style="width:418px" %)Computer sends negative terminal (drive receives negative)
871 |(% style="width:90px" %)2|(% style="width:102px" %)485+|(% style="width:418px" %)Computer sends positive terminal (drive receives positive)
872 |(% style="width:90px" %)3|(% style="width:102px" %)-|(% style="width:418px" %)Computer receives negative terminal
873 |(% style="width:90px" %)4|(% style="width:102px" %)GND|(% style="width:418px" %)Ground terminal
874 |(% style="width:90px" %)5|(% style="width:102px" %)-|(% style="width:418px" %)Not used
875 |(% style="width:90px" %)6|(% style="width:102px" %)-|(% style="width:418px" %)Computer receives positive terminal
876 |(% style="width:90px" %)7|(% style="width:102px" %)-|(% style="width:418px" %)Not used
877 |(% style="width:90px" %)8|(% style="width:102px" %)-|(% style="width:418px" %)Not used