Skip to Content

Wiki source code of 04 Wiring

Version 45.1 by Joey on 2022/06/10 14:10
Show last authors
1 = **Main circuit wiring** =
2
3 == **Main circuit terminals** ==
4
5
6 (((
7 **VD2A servo drive main circuit terminal distribution**
8 )))
9
10 (% style="text-align:center" %)
11 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_c8486fa03c80511d.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_c8486fa03c80511d.gif"]]
12
13 Figure 4-1 VD2A servo drive main circuit terminal distribution
14
15 (% class="table-bordered" %)
16 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
17 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="3" %)Single-phase 220V AC input is connected to L1 and L3.
18 |(% style="text-align:center; vertical-align:middle" %)L2
19 |(% style="text-align:center; vertical-align:middle" %)L3
20 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
21 Use internal braking resistor: short-circuit C and D.
22
23 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C;
24 )))
25 |(% style="text-align:center; vertical-align:middle" %)C
26 |(% style="text-align:center; vertical-align:middle" %)D
27 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of motor to power the motor.
28 |(% style="text-align:center; vertical-align:middle" %)V
29 |(% style="text-align:center; vertical-align:middle" %)W
30 |(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
31
32 Table 4-1 The name and function of VD2A servo drive main circuit terminal
33
34 **VD2B servo drive main circuit terminal distribution**
35
36 (% style="text-align:center" %)
37 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_17042d8c7761266a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_17042d8c7761266a.gif"]]
38
39 Figure 4-2 VD2B servo drive main circuit terminal distribution
40
41 (% class="table-bordered" %)
42 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
43 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="3" %)(((
44 Three-phase 220V AC input is connected to L1, L2, L3;
45
46 Single-phase 220V AC input is connected to L1 and L3.
47 )))
48 |(% style="text-align:center; vertical-align:middle" %)L2
49 |(% style="text-align:center; vertical-align:middle" %)L3
50 |(% style="text-align:center; vertical-align:middle" %)L1C|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Control power input terminal|(% rowspan="2" %)Single-phase 220V AC input is connected to L1C and L2C.
51 |(% style="text-align:center; vertical-align:middle" %)L2C
52 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
53 Use internal braking resistor: short-circuit C and D.
54
55 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
56 )))
57 |(% style="text-align:center; vertical-align:middle" %)C
58 |(% style="text-align:center; vertical-align:middle" %)D
59 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of motor to power the motor.
60 |(% style="text-align:center; vertical-align:middle" %)V
61 |(% style="text-align:center; vertical-align:middle" %)W
62 |(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
63
64 Table 4-2 The name and function of VD2B servo drive main circuit terminal
65
66 **VD2F servo drive main circuit terminal distribution**
67
68 (% style="text-align:center" %)
69 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6dd68f214c0f9f79.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6dd68f214c0f9f79.gif"]]
70
71 Figure 4-3 VD2F servo drive main circuit terminal distribution
72
73 (% class="table-bordered" %)
74 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
75 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="2" %)Connect single-phase 220V input power
76 |(% style="text-align:center; vertical-align:middle" %)L2
77 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
78 Use internal braking resistor: short-circuit C and D.
79
80 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
81 )))
82 |(% style="text-align:center; vertical-align:middle" %)C
83 |(% style="text-align:center; vertical-align:middle" %)D
84 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Common DC bus terminal|(% rowspan="2" %)DC bus terminal of servo drive
85 |(% style="text-align:center; vertical-align:middle" %)N
86 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of the motor to power the motor.
87 |(% style="text-align:center; vertical-align:middle" %)V
88 |(% style="text-align:center; vertical-align:middle" %)W
89 |(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
90
91 Table 4-3 The name and function of VD2F servo drive main circuit terminal
92
93 == **Power wiring** ==
94
95 **VD2A drive single-phase 220V main circuit wiring**
96
97 (% style="text-align:center" %)
98 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9d2a6455f3f19347.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9d2a6455f3f19347.gif" data-xwiki-image-style-alignment="center" height="638" width="750"]]
99
100 Figure 4-4 VD2A drive single-phase 220V main circuit wiring
101
102 **VD2B drive single-phase 220V main circuit wiring**
103
104 (% style="text-align:center" %)
105 [[image:image-20220608141527-2.png||height="657" width="750"]]
106
107 Figure 4-5 VD2B drive single-phase 220V main circuit wiring
108
109 **VD2B drive three-phase 220V main circuit wiring**
110
111 (% style="text-align:center" %)
112 [[image:image-20220608141722-3.png||height="662" width="750"]]
113
114 Figure 4-6 VD2B drive three-phase 220V main circuit wiring
115
116 **VD2F drive single-phase 220V main circuit wiring**
117
118 (% style="text-align:center" %)
119 [[image:image-20220608141754-4.png||height="674" width="750"]]
120
121
122 Figure 4-7 VD2F drive single-phase 220V main circuit wiring
123
124 == **Precautions for main circuit wiring** ==
125
126 1. Do not connect the input power cord to the output terminals U, V, W, otherwise the servo drive will be damaged. When using the built-in braking resistor, C and D must be connected (factory default connection).
127 1. When the cables are bundled and used in pipes, etc., due to the deterioration of heat dissipation conditions, please consider the allowable current reduction rate.
128 1. When the temperature in the cabinet is higher than the cable temperature limit, please choose a cable with a larger cable temperature limit, and it is recommended that the cable wire use Teflon wire. Please pay attention to the warmth of the cable in the low temperature environment. Generally, the surface of the cable is easy to harden and break under the low temperature environment.
129 1. The bending radius of the cable should be more than 10 times the outer diameter of the cable itself to prevent the core of the cable from breaking due to long-term bending.
130
131 = **Power line connection of servo drive and servo motor** =
132
133 == **Power line** ==
134
135 Wecon VD2 series servo drive have 3 kinds of interface power cables: rectangular plug, aviation plug and in-line type.
136
137 (% class="table-bordered" %)
138 |(% style="text-align:center; vertical-align:middle" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle" %)**Terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Pin description**|(% style="text-align:center; vertical-align:middle" %)(((
139 **Motor flange**
140 )))
141 |(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610092710-1.png]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610092728-2.png]]|(% style="text-align:center; vertical-align:middle" %)Rectangular plug(((
142 (% class="table-bordered" %)
143 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
144 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
145 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
146 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
147 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
148 )))|(% style="text-align:center; vertical-align:middle" %)(((
149 40
150
151 60
152
153 80
154 )))
155 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9335f5058d76f79a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9335f5058d76f79a.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:image-20220610100433-1.png]]|(% style="text-align:center; vertical-align:middle" %)Aviation plug(((
156 (% class="table-bordered" %)
157 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
158 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Black
159 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)Yellow-green
160 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
161 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Black
162 )))|(% style="text-align:center; vertical-align:middle" %)(((
163 110
164
165 130
166 )))
167 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_77117dacdd5935b9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_77117dacdd5935b9.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_7e9ea795751e109c.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_7e9ea795751e109c.gif"]]|(% style="text-align:center; vertical-align:middle" %)In-line type plug(((
168 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
169 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
170 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
171 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
172 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
173 )))|(% style="text-align:center; vertical-align:middle" %)(((
174 60
175
176 80
177 )))
178
179 Table 4-4 Power cable servo motor side connector
180
181 ✎**Note:** The color of the lines is subject to the actual product. The lines described in this manual are all lines of Wecon.
182
183 == **Brake device cable** ==
184
185 (% class="table-bordered" %)
186 |(% colspan="2" style="text-align:center; vertical-align:middle; width:475px" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle; width:277px" %)**terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
187 |(% style="text-align:center; vertical-align:middle" %)WD series|(% style="text-align:center; vertical-align:middle; width:374px" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9be5695e6c0fd897.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9be5695e6c0fd897.gif" height="103" width="128"]]|(% style="width:277px" %)(((
188 (% class="table-bordered" %)
189 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
190 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)BR+
191 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)BR-
192 )))|(% style="text-align:center; vertical-align:middle" %)(((
193 40
194
195 60
196
197 80
198 )))
199 |(% style="text-align:center; vertical-align:middle" %)WE series|(% style="text-align:center; vertical-align:middle; width:374px" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_576ebded84acbded.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_576ebded84acbded.gif" height="173" width="190"]]|(% style="width:277px" %)(((
200 (% class="table-bordered" %)
201 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
202 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DC 24V
203 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND
204 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)-
205 )))|(% style="text-align:center; vertical-align:middle" %)(((
206 80
207
208 110
209
210 130
211 )))
212
213 Table 4-5 Brake device cable
214
215 == **Encoder cable connection of servo drive and servo motor** ==
216
217 (% style="text-align:center" %)
218 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_2a7019b4f21f159e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_2a7019b4f21f159e.gif" height="324" width="857"]]
219
220 Figure 4-8 Encoder connection line wiring
221
222 (% class="table-bordered" %)
223 |(% style="text-align:center; vertical-align:middle" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle" %)**Terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Pin description**
224 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_c798aa1eac035779.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_c798aa1eac035779.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_671f87b1a542ce32.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_671f87b1a542ce32.gif"]]|(((
225 (% class="table-bordered" %)
226 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
227 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)E-
228 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+
229 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)E+|(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-
230 )))
231
232 Table 4-6 Encoder cable servo drive side connector
233
234 (% class="table-bordered" %)
235 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Connector exterior and terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
236 |(% style="text-align:center; vertical-align:middle" %)(((
237 (% style="text-align:center" %)
238 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_a41c00ba1133ea20.png?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_a41c00ba1133ea20.png" height="145" width="502"]]
239
240
241 )))|(((
242 (% style="text-align:center" %)
243 [[image:image-20220608142110-6.png||height="182" width="278"]]
244 )))|(% rowspan="3" style="text-align:center; vertical-align:middle" %)(((
245 40
246
247 60
248
249 80
250 )))
251 |(% style="text-align:center; vertical-align:middle" %)(((
252 (% style="text-align:center" %)
253 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_1ce0548bf47ef5ae.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_1ce0548bf47ef5ae.gif"]]
254 )))|(((
255 (% style="text-align:center" %)
256 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_4cb7be8f7bd5893e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_4cb7be8f7bd5893e.gif"]]
257 )))
258 |(% colspan="2" %)(((
259 (% class="table-bordered" %)
260 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
261 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
262 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)GND
263 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD+
264 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD-
265 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Shield
266 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Battery+
267 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
268 )))
269
270 Table 4-7 Absolute value encoder line connector (Rectangular plug)
271
272 (% class="table-bordered" %)
273 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle" %)**Motor side**
274 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Rectangular plug pin number**|(% style="text-align:center; vertical-align:middle" %)**Cable color**
275 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Blue
276 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Encoder power ground|(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Orange
277 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+|(% style="text-align:center; vertical-align:middle" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Green
278 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-|(% style="text-align:center; vertical-align:middle" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Brown
279 |(% style="text-align:center; vertical-align:middle" %)Shell|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)~-~-
280 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery+|(% style="text-align:center; vertical-align:middle" %)1*|(% style="text-align:center; vertical-align:middle" %)Pink
281 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery-|(% style="text-align:center; vertical-align:middle" %)2*|(% style="text-align:center; vertical-align:middle" %)Pink-Black
282
283 Table 4-8 Connection of encoder line pin
284
285 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
286
287 ✎ **Note: **The color of the line is subject to the actual product. The lines described in this manual are all lines of Wecon!
288
289 (% class="table-bordered" %)
290 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Connector shape and terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
291 |(% style="text-align:center; vertical-align:middle; width:531px" %)(((
292 (% style="text-align:center" %)
293 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_d450a92cc1507fcd.png?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_d450a92cc1507fcd.png" height="178" width="487"]]
294 )))|(% style="text-align:center; vertical-align:middle; width:530px" %)[[image:image-20220608142557-7.png]]|(% rowspan="3" style="text-align:center; vertical-align:middle" %)(((
295 110
296
297 130
298 )))
299 |(% style="width:531px" %)(((
300 (% style="text-align:center" %)
301 [[image:image-20220608144304-1.png]]
302 )))|(% style="width:530px" %)(((
303 (% style="text-align:center" %)
304 [[image:image-20220608144357-2.png]]
305 )))
306 |(% colspan="2" %)(((
307 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
308 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
309 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND
310 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD+
311 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD-
312 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Shield
313 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Battery+
314 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
315 )))
316
317 Table 4-9 Absolute value encoder line connector (Aviation plug)
318
319 (% class="table-bordered" %)
320 |(% colspan="2" style="text-align:center; vertical-align:middle; width:258px" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle; width:273px" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle; width:365px" %)**Motor side**
321 |(% style="text-align:center; vertical-align:middle; width:126px" %)**Pin number**|(% style="text-align:center; vertical-align:middle; width:128px" %)**Signal name**|(% style="text-align:center; vertical-align:middle; width:218px" %)(((
322 **Aviation plug pin number**
323 )))|(% style="text-align:center; vertical-align:middle; width:156px" %)**Cable  color**
324 |(% style="text-align:center; vertical-align:middle; width:126px" %)1|(% style="text-align:center; vertical-align:middle; width:128px" %)5V|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle; width:218px" %)7|(% style="text-align:center; vertical-align:middle; width:156px" %)Blue
325 |(% style="text-align:center; vertical-align:middle; width:126px" %)2|(% style="text-align:center; vertical-align:middle; width:128px" %)GND|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder power ground|(% style="text-align:center; vertical-align:middle; width:218px" %)8|(% style="text-align:center; vertical-align:middle; width:156px" %)Orange
326 |(% style="text-align:center; vertical-align:middle; width:126px" %)5|(% style="text-align:center; vertical-align:middle; width:128px" %)SD+|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle; width:218px" %)4|(% style="text-align:center; vertical-align:middle; width:156px" %)Green
327 |(% style="text-align:center; vertical-align:middle; width:126px" %)6|(% style="text-align:center; vertical-align:middle; width:128px" %)SD-|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle; width:218px" %)5|(% style="text-align:center; vertical-align:middle; width:156px" %)Brown
328 |(% style="text-align:center; vertical-align:middle; width:126px" %)Shell|(% style="text-align:center; vertical-align:middle; width:128px" %)Shield|(% style="text-align:center; vertical-align:middle; width:273px" %)Shield|(% style="text-align:center; vertical-align:middle; width:218px" %)3|(% style="text-align:center; vertical-align:middle; width:156px" %)-
329 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery+|(% style="text-align:center; vertical-align:middle; width:218px" %)1*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink
330 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery-|(% style="text-align:center; vertical-align:middle; width:218px" %)2*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink-Black
331
332 Table 4-10 Absolute encoder cable connector (aviation socket)
333
334 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
335
336 ✎ **Note: **The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
337
338 (% class="table-bordered" %)
339 |(% colspan="2" style="text-align:center; vertical-align:middle; width:791px" %)**Connector shape and terminal pin distribution**|(% style="text-align:center; vertical-align:middle; width:94px" %)(((
340 **Motor**
341
342 **flange**
343 )))
344 |(% style="text-align:center; vertical-align:middle; width:544px" %)(((
345 (% style="text-align:center" %)
346 [[image:image-20220608144543-3.png||height="203" width="495"]]
347 )))|(% style="width:563px" %)(((
348 (% style="text-align:center" %)
349 [[image:image-20220608144728-6.png]]
350 )))|(% rowspan="3" style="text-align:center; vertical-align:middle; width:94px" %)(((
351 60
352
353 80
354 )))
355 |(% style="text-align:center; vertical-align:middle; width:544px" %)(((
356 (% style="text-align:center" %)
357 [[image:image-20220608144619-5.png||height="147" width="353"]]
358 )))|(% style="width:563px" %)(((
359 (% style="text-align:center" %)
360 [[image:image-20220608144750-7.png||height="137" width="358"]]
361 )))
362 |(% colspan="2" style="width:791px" %)(((
363 (% class="table-bordered" %)
364 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
365 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
366 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND
367 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD+
368 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD-
369 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Shield
370 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Battery+
371 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
372 )))
373
374 Table 4-11 Absolute encoder cable connector (in-line type)
375
376 (% class="table-bordered" %)
377 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle" %)**Motor side**
378 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)(((
379 **In-line plug**
380
381 **pin number**
382 )))|(% style="text-align:center; vertical-align:middle" %)**Cable color**
383 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Blue
384 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Encoder power ground|(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Orange
385 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+|(% style="text-align:center; vertical-align:middle" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Green
386 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-|(% style="text-align:center; vertical-align:middle" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Brown
387 |(% style="text-align:center; vertical-align:middle" %)Shell|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)-
388 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery+|(% style="text-align:center; vertical-align:middle" %)3*|(% style="text-align:center; vertical-align:middle" %)Brown
389 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery-|(% style="text-align:center; vertical-align:middle" %)2*|(% style="text-align:center; vertical-align:middle" %)Black
390
391 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
392
393 ✎**Note:** The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
394
395 = **Servo drive control input and output wiring** =
396
397 == **CN2 pin distribution** ==
398
399 **VD2A and VD2B servo drive control input and output pin distribution (CN2 interface)**
400
401 (% style="text-align:center" %)
402 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_e8200287ad0381e3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_e8200287ad0381e3.gif"]]
403
404 Figure 4-9 VD2A and VD2B servo drive control input and output pin distribution
405
406 (% class="table-bordered" %)
407 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
408 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)16|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)31|(% style="text-align:center; vertical-align:middle" %)-
409 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)AI_2+|(% style="text-align:center; vertical-align:middle" %)17|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)32|(% style="text-align:center; vertical-align:middle" %)AI_1+
410 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)AI_2-|(% style="text-align:center; vertical-align:middle" %)18|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)33|(% style="text-align:center; vertical-align:middle" %)AI_1-
411 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DO1-|(% style="text-align:center; vertical-align:middle" %)19|(% style="text-align:center; vertical-align:middle" %)DO3-|(% style="text-align:center; vertical-align:middle" %)34|(% style="text-align:center; vertical-align:middle" %)GND
412 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DO1+|(% style="text-align:center; vertical-align:middle" %)20|(% style="text-align:center; vertical-align:middle" %)DO3+|(% style="text-align:center; vertical-align:middle" %)35|(% style="text-align:center; vertical-align:middle" %)-
413 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO2-|(% style="text-align:center; vertical-align:middle" %)21|(% style="text-align:center; vertical-align:middle" %)DO4-|(% style="text-align:center; vertical-align:middle" %)36|(% style="text-align:center; vertical-align:middle" %)-
414 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2+|(% style="text-align:center; vertical-align:middle" %)22|(% style="text-align:center; vertical-align:middle" %)DO4+|(% style="text-align:center; vertical-align:middle" %)37|(% style="text-align:center; vertical-align:middle" %)-
415 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)23|(% style="text-align:center; vertical-align:middle" %)DI5|(% style="text-align:center; vertical-align:middle" %)38|(% style="text-align:center; vertical-align:middle" %)-
416 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)24|(% style="text-align:center; vertical-align:middle" %)DI6|(% style="text-align:center; vertical-align:middle" %)39|(% style="text-align:center; vertical-align:middle" %)-
417 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)25|(% style="text-align:center; vertical-align:middle" %)DI7|(% style="text-align:center; vertical-align:middle" %)40|(% style="text-align:center; vertical-align:middle" %)SIGN-
418 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)26|(% style="text-align:center; vertical-align:middle" %)DI8|(% style="text-align:center; vertical-align:middle" %)41|(% style="text-align:center; vertical-align:middle" %)SIGN+
419 |(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)27|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)42|(% style="text-align:center; vertical-align:middle" %)PULS-
420 |(% style="text-align:center; vertical-align:middle" %)13|(% style="text-align:center; vertical-align:middle" %)PAO-|(% style="text-align:center; vertical-align:middle" %)28|(% style="text-align:center; vertical-align:middle" %)PAO+|(% style="text-align:center; vertical-align:middle" %)43|(% style="text-align:center; vertical-align:middle" %)PULS+
421 |(% style="text-align:center; vertical-align:middle" %)14|(% style="text-align:center; vertical-align:middle" %)PBO-|(% style="text-align:center; vertical-align:middle" %)29|(% style="text-align:center; vertical-align:middle" %)PBO+|(% style="text-align:center; vertical-align:middle" %)44|(% style="text-align:center; vertical-align:middle" %)PL
422 |(% style="text-align:center; vertical-align:middle" %)15|(% style="text-align:center; vertical-align:middle" %)PZO-|(% style="text-align:center; vertical-align:middle" %)30|(% style="text-align:center; vertical-align:middle" %)PZO+|(% style="text-align:center; vertical-align:middle" %)~-~-|(% style="text-align:center; vertical-align:middle" %)~-~-
423
424 Table 4-12 CN2 interface definition of VD2A and VD2B servo drive
425
426 **VD2F servo drive control input and output pin distribution (CN2 interface)**
427
428 (% style="text-align:center" %)
429 [[image:image-20220610135735-1.png]]
430
431 Figure 4-10 VD2F servo drive control input and output pin distribution
432
433 (% class="table-bordered" %)
434 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
435 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DO3|(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI4
436 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)DO1|(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2
437 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)PL
438 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)PULS+
439 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)13|(% style="text-align:center; vertical-align:middle" %)PULS-
440 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO4|(% style="text-align:center; vertical-align:middle" %)14|(% style="text-align:center; vertical-align:middle" %)SIGN+
441 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2|(% style="text-align:center; vertical-align:middle" %)15|(% style="text-align:center; vertical-align:middle" %)SIGN-
442 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DOCOM|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-
443
444 Table 4-13 CN2 interface definition of VD2F servo drive
445
446 == **Wiring diagram of each mode** ==
447
448 **VD2A and VD2B servo drive**
449
450 (% style="text-align:center" %)
451 [[image:4-11.jpg||height="961" width="750"]]
452
453 Figure 4-11 Wiring diagram of each mode
454
455 ✎**Note:** Please refer to "[[__4.4.1 __Table 4-12 CN2 interface definition of VD2A and VD2B servo drive>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_e8200287ad0381e3.gif?rev=1.1]]" for the pin numbers in the figure.
456
457 **VD2F servo drive**
458
459 (% style="text-align:center" %)
460 [[image:image-20220608145058-9.png]]
461
462 Figure 4-12 Position pulse mode wiring
463
464 ✎**Note:** Please refer to "[[__4.4.1 __Table 4-13 CN2 interface definition of VD2F servo drive>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_55a725365ef15a86.gif?rev=1.1]]" for the pin numbers in the figure.
465
466 == **Position instruction input signal** ==
467
468 (% class="table-bordered" %)
469 |(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**VD2A and VD2B pin number**|(% style="text-align:center; vertical-align:middle" %)**VD2F pin number**|(% style="text-align:center; vertical-align:middle" %)**Function**
470 |(% style="text-align:center; vertical-align:middle" %)PULS+|(% style="text-align:center; vertical-align:middle" %)43|(% style="text-align:center; vertical-align:middle" %)12|(% rowspan="4" %)(((
471 Low-speed pulse input modes: differential input, open collector.
472
473 There are three types of input pulse:
474
475 1. Direction + pulse (positive logic);
476 1. CW/CCW;
477 1. A and B phase quadrature pulses (4 times the
478
479 frequency).
480 )))
481 |(% style="text-align:center; vertical-align:middle" %)PULS-|(% style="text-align:center; vertical-align:middle" %)42|(% style="text-align:center; vertical-align:middle" %)13
482 |(% style="text-align:center; vertical-align:middle" %)SIGN+|(% style="text-align:center; vertical-align:middle" %)41|(% style="text-align:center; vertical-align:middle" %)14
483 |(% style="text-align:center; vertical-align:middle" %)SIGN-|(% style="text-align:center; vertical-align:middle" %)40|(% style="text-align:center; vertical-align:middle" %)15
484 |(% style="text-align:center; vertical-align:middle" %)PL|(% style="text-align:center; vertical-align:middle" %)44|(% style="text-align:center; vertical-align:middle" %)11|External power input interface for instruction pulse.
485
486 Table 4-14 Position instruction signal description
487
488 The instruction pulse and sign output circuit on the host device side can be selected from differential output or open collector output. The maximum input frequency is shown in the table.
489
490 (% class="table-bordered" %)
491 |(% style="text-align:center; vertical-align:middle" %)**Pulse method**|(% style="text-align:center; vertical-align:middle" %)**Difference**|(% style="text-align:center; vertical-align:middle" %)**Open collector**
492 |(% style="text-align:center; vertical-align:middle" %)Maximum frequency|(% style="text-align:center; vertical-align:middle" %)500KHz|(% style="text-align:center; vertical-align:middle" %)200KHz
493
494 **Differential input**
495
496 The connection of differential input is shown in Figure 4-9
497
498 (% style="text-align:center" %)
499 [[image:image-20220610140653-1.png]]
500
501 Figure 4-13 VD2A and VD2B servo drive differential input connection
502
503 (% style="text-align:center" %)
504 [[image:image-20220610141030-1.png]]
505
506 Figure 4-14 VD2F servo drive differential input connection
507
508 **Open collector input**
509
510 1.Open collector input connection
511
512 (% style="text-align:center" %)
513 [[image:image-20220609111236-7.jpeg||height="441" width="610"]]
514
515 Figure 4-15 VD2A and VD2B servo drive open collector input connection
516
517 (% style="text-align:center" %)
518 [[image:image-20220609111352-8.jpeg||height="431" width="600"]]
519
520 Figure 4-16 VD2F servo drive open collector input connection
521
522 2.NPN and PNP wiring
523
524 (% class="table-bordered" %)
525 |(% style="width:597px" %)(((
526 (% style="text-align:center" %)
527 [[image:image-20220609111643-11.jpeg]]
528 )))|(% style="width:478px" %)(((
529 (% style="text-align:center" %)
530 [[image:image-20220609111654-12.jpeg]]
531 )))
532 |(% style="text-align:center; vertical-align:middle; width:597px" %)NPN|(% style="text-align:center; vertical-align:middle; width:478px" %)PNP
533 |(% colspan="2" style="text-align:center; vertical-align:middle" %)Figure 4-17 Triode Wiring
534
535 == **Analog input signal** ==
536
537 The analog input signal is only supported by VD2A and VD2B servo drives.
538
539 (% class="table-bordered" %)
540 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Function**
541 |(% style="text-align:center; vertical-align:middle" %)32|(% style="text-align:center; vertical-align:middle" %)AI_1+|(% rowspan="2" %)(((
542 AI_1 analog input signal, resolution 12-bit.
543
544 Input voltage range: -10V to +10V.
545 )))
546 |(% style="text-align:center; vertical-align:middle" %)33|(% style="text-align:center; vertical-align:middle" %)AI_1-
547 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)AI_2+|(% rowspan="2" %)(((
548 AI_2 analog input signal, resolution 12-bit.
549
550 Input voltage range: -10V to +10V.
551 )))
552 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)AI_2-
553 |(% style="text-align:center; vertical-align:middle" %)17|(% style="text-align:center; vertical-align:middle" %)GND|(% rowspan="2" %)Analog input signal ground.
554 |(% style="text-align:center; vertical-align:middle" %)34|(% style="text-align:center; vertical-align:middle" %)GND
555
556 Table 4-15 Analog input signal description
557
558 (% style="text-align:center" %)
559 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_189eff54d0bbd5af.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_189eff54d0bbd5af.gif"]]
560
561 Figure 4-18 Analog input wiring
562
563
564 == **Digital input and output signals** ==
565
566 **VD2A and VD2B servo drives**
567
568 (% class="table-bordered" %)
569 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Default function**
570 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
571 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
572 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
573 |(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
574 |(% style="text-align:center; vertical-align:middle" %)23|(% style="text-align:center; vertical-align:middle" %)DI5|(% style="text-align:center; vertical-align:middle" %)Inverted instruction
575 |(% style="text-align:center; vertical-align:middle" %)24|(% style="text-align:center; vertical-align:middle" %)DI6|(% style="text-align:center; vertical-align:middle" %)Instruction pulse prohibited input
576 |(% style="text-align:center; vertical-align:middle" %)25|(% style="text-align:center; vertical-align:middle" %)DI7|(% style="text-align:center; vertical-align:middle" %)Not used
577 |(% style="text-align:center; vertical-align:middle" %)26|(% style="text-align:center; vertical-align:middle" %)DI8|(% style="text-align:center; vertical-align:middle" %)Not used
578 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DICOM|(% style="text-align:center; vertical-align:middle" %)24V
579 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DO1-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Rotation detection
580 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DO1+
581 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO2-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Faults signal
582 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2+
583 |(% style="text-align:center; vertical-align:middle" %)19|(% style="text-align:center; vertical-align:middle" %)DO3-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Servo is ready
584 |(% style="text-align:center; vertical-align:middle" %)20|(% style="text-align:center; vertical-align:middle" %)DO3+
585 |(% style="text-align:center; vertical-align:middle" %)21|(% style="text-align:center; vertical-align:middle" %)DO4-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Positioning completed
586 |(% style="text-align:center; vertical-align:middle" %)22|(% style="text-align:center; vertical-align:middle" %)DO4+
587
588 Table 4-16 DI/DO signal description
589
590 **Digital input circuit**
591
592 1.When the control device(HMI/PLC) is relay output
593
594 (% style="text-align:center" %)
595 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_df384a263bb6da8e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_df384a263bb6da8e.gif"]]
596
597 Figure 4-19 Relay output
598
599 2.When the control device(HMI/PLC) is open collector output
600
601 (% style="text-align:center" %)
602 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_bd7bc86ca63a344b.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_bd7bc86ca63a344b.gif"]]
603
604 Figure 4-20 Open collector output
605
606 **Digital output circuit**
607
608 1.When the control device(HMI/PLC) is relay input
609
610 (% style="text-align:center" %)
611 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_f16ac03591f1a0a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_f16ac03591f1a0a.gif"]]
612
613 Figure 4-21 Relay input
614
615 2.When the control device(HMI/PLC) is optocoupler input
616
617 (% style="text-align:center" %)
618 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_d1e75001d4cc31f9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_d1e75001d4cc31f9.gif"]]
619
620 Figure 4-22 Optocoupler input
621
622 **VD2F servo drive**
623
624 (% class="table-bordered" %)
625 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Pin name**|(% style="text-align:center; vertical-align:middle" %)**Default function**
626 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
627 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
628 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
629 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
630 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)Power input (24V)
631 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)DO1|(% style="text-align:center; vertical-align:middle" %)Rotation detection
632 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2|(% style="text-align:center; vertical-align:middle" %)Fault signal
633 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DO3|(% style="text-align:center; vertical-align:middle" %)Servo is ready
634 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO4|(% style="text-align:center; vertical-align:middle" %)Positioning completed
635 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DOCOM|(% style="text-align:center; vertical-align:middle" %)Do common terminal
636
637 Table 4-17 DI/DO signal description
638
639 **Digital input circuit**
640
641 1.When the control device(HMI/PLC) is relay output
642
643 (% style="text-align:center" %)
644 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6861cbbee65afc3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6861cbbee65afc3.gif"]]
645
646 Figure 4-23 Relay output
647
648 2.When the control device(HMI/PLC) is open collector output
649
650 (% style="text-align:center" %)
651 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_ce4de1a5701b382d.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_ce4de1a5701b382d.gif"]]
652
653 Figure 4-24 Open collector output
654
655 **Digital output circuit**
656
657 1.When the control device(HMI/PLC) is relay input
658
659 (% style="text-align:center" %)
660 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_1416274c5f871283.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_1416274c5f871283.gif"]]
661
662 Figure 4-25 Relay output
663
664 2.When the control device(HMI/PLC) is optocoupler input
665
666 (% style="text-align:center" %)
667 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3ade436b150a75d9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_3ade436b150a75d9.gif"]]
668
669 Figure 4-26 Optocoupler input
670
671 == **Brake wiring** ==
672
673 The brake is a mechanism that prevents the servo motor shaft from moving when the servo drive is in a non-running state, so that the motor remains in position lock, so that the moving part of the machinery will not move due to self-weight or external force.
674
675 Brake input signal is no polar. You need to use 24V power . The standard wiring between brake signal BK and brake power is as below.
676
677 (% style="text-align:center" %)
678 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_8000f59dd6848011.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_8000f59dd6848011.gif"]]
679
680 Figure 4-27 Brake wiring (three-phase 220V input)
681
682 (% style="text-align:center" %)
683 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_dcaf5f24afc3957b.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_dcaf5f24afc3957b.gif"]]
684
685 Figure 4-28 Brake wiring (single-phase 220V input)
686
687 = **Communication signal wiring** =
688
689 Wecon VD2 series servo drive supports two communication modes: RS-422 and RS-485. The exterior of communication terminal is shown in Figure 4-29.
690
691 (% style="text-align:center" %)
692 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_36a1ac5641d607b2.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_36a1ac5641d607b2.gif" height="159" width="157"]]
693
694 Figure 4-29 communication port exterior and pin definition
695
696 == **Communication signal connector** ==
697
698 **(1) VD2A and VD2B servo drive**
699
700 The signal connectors exterior of RS422 and RS485 communication methods are shown in Figure 4-19 (a) and (b) respectively.
701
702 (% class="table-bordered" %)
703 |(((
704 (% style="text-align:center" %)
705 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6017da4ef2b79ce3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6017da4ef2b79ce3.gif"]]
706 )))|(((
707 (% style="text-align:center" %)
708 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_54ecc0baf9dc3fe8.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_54ecc0baf9dc3fe8.gif"]]
709 )))
710 |(% style="text-align:center; vertical-align:middle" %)(A) RS422 communication|(% style="text-align:center; vertical-align:middle" %)(B) RS485 communication
711 |(% colspan="2" style="text-align:center; vertical-align:middle" %)Figure 4-30 VD2A and VD2B servo drive communication signal connector exterior
712
713 **(2) VD2F servo drive**
714
715 The CN3 and CN4 interfaces support RS422 and RS485 communication methods. The exterior of the communication signal connector is shown in __[[Figure 4-31>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3036b46714cd6b88.gif?rev=1.1]]__. __[[Table 4-18>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/#HCommunicationsignalconnector]]__ is the pin definition corresponding to the two communications.
716
717 (% style="text-align:center" %)
718 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3036b46714cd6b88.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_3036b46714cd6b88.gif"]]
719
720 Figure 4-31 VD2F servo drive communication signal connector exterior
721
722 (% class="table-bordered" %)
723 |(% colspan="2" style="text-align:center; vertical-align:middle" %)(((
724 **Communication method Pin number and function**
725 )))|(% style="text-align:center; vertical-align:middle" %)**Pin name corresponding to RS422 communication**|(% style="text-align:center; vertical-align:middle" %)**Pin name corresponding to RS485 communication**
726 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal|(% style="text-align:center; vertical-align:middle" %)RX-|(% style="text-align:center; vertical-align:middle" %)485-
727 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal|(% style="text-align:center; vertical-align:middle" %)RX+|(% style="text-align:center; vertical-align:middle" %)485+
728 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Computer receives negative terminal|(% style="text-align:center; vertical-align:middle" %)TX-|(% style="text-align:center; vertical-align:middle" %)-
729 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)GND
730 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
731 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)Computer receives positive terminal|(% style="text-align:center; vertical-align:middle" %)TX+|(% style="text-align:center; vertical-align:middle" %)-
732 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
733 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
734
735 Table 4-18 VD2F servo drive communication signal connector pin definition
736
737 == **Host computer communication connection** ==
738
739 VD2A and VD2B servo drives communicate with the host computer via the CN3 interface by RS422 communication. Table 4-9 is the pin definition of the CN3 interface. The communication diagrams of VD2A and VD2B servo drives and host computer are shown in __[[Figure 4-32>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_2a6d3dc0bc5368b7.gif?rev=1.1]]__ and __[[Figure 4-33 >>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9d156f3c473d7fc.gif?rev=1.1]]__respectively.
740
741 (% class="table-bordered" %)
742 |(% style="text-align:center; vertical-align:middle" %)**Pin**|(% style="text-align:center; vertical-align:middle" %)**Name**|(% style="text-align:center; vertical-align:middle" %)**Function description**
743 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)RX-|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal (drive receives negative)
744 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)RX+|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal (drive receives positive)
745 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)TX-|(% style="text-align:center; vertical-align:middle" %)Computer receives negative terminal (drive sends negative)
746 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
747 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
748 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)TX+|(% style="text-align:center; vertical-align:middle" %)Computer receives positive terminal (drive sends positive)
749 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
750 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
751
752 Table 4-19 The pin definition of CN3 interface
753
754 (% style="text-align:center" %)
755 [[image:image-20220608145637-11.png]]
756
757 Figure 4-32 The Connection between VD2A drive and PC
758
759 (% style="text-align:center" %)
760 [[image:image-20220608145828-14.png]]
761
762 Figure 4-33 The connection between VD2B drive and PC
763
764 VD2F servo drive communicates with the host computer via the CN3 or CN4 interface byRS422 communication. The communication diagrams of VD2F servo drive and host computer are shown in __[[Figure 4-34>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#F434]]__ respectively.
765
766 (% style="text-align:center" %)
767 [[image:image-20220608145750-13.png]]
768
769 Figure 4-34 The connection between VD2F drive and PC
770
771 == **PLC communication connection** ==
772
773 VD2A and VD2B servo drives communicate with the PLC via CN5 or CN6 interface (located on the top of servo drive) by RS485 communication.
774
775 VD2F servo drive communicates with the PLC via CN3 or CN4 interface by RS485 communication.
776
777 (% class="table-bordered" %)
778 |(% style="text-align:center; vertical-align:middle" %)**Pin**|(% style="text-align:center; vertical-align:middle" %)**Name**|(% style="text-align:center; vertical-align:middle" %)**Function description**
779 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)485+|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal (drive receives negative)
780 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)485-|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal (drive receives positive)
781 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
782 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
783 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
784 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
785 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Reserved|(% style="text-align:center; vertical-align:middle" %)Reserved
786 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
787
788 Table 4-20 The pin definition of CN5/CN6 interface