Skip to Content

Wiki source code of 04 Wiring

Version 6.3 by Leo Wei on 2022/06/09 11:28
Show last authors
1 = **Main circuit wiring** =
2
3 == **Main circuit terminals** ==
4
5 [[image:image-20220609112700-1.png]]
6
7
8 (((
9 **VD2A servo drive main circuit terminal distribution**
10 )))
11
12 (% style="text-align:center" %)
13 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_c8486fa03c80511d.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_c8486fa03c80511d.gif"]]
14
15 Figure 4-1 VD2A servo drive main circuit terminal distribution
16
17 (% class="table-bordered" %)
18 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
19 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="3" %)Single-phase 220V AC input is connected to L1 and L3.
20 |(% style="text-align:center; vertical-align:middle" %)L2
21 |(% style="text-align:center; vertical-align:middle" %)L3
22 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
23 Use internal braking resistor: short-circuit C and D.
24
25 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C;
26 )))
27 |(% style="text-align:center; vertical-align:middle" %)C
28 |(% style="text-align:center; vertical-align:middle" %)D
29 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of motor to power the motor.
30 |(% style="text-align:center; vertical-align:middle" %)V
31 |(% style="text-align:center; vertical-align:middle" %)W
32 |(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
33
34 Table 4-1 The name and function of VD2A servo drive main circuit terminal
35
36 **VD2B servo drive main circuit terminal distribution**
37
38 (% style="text-align:center" %)
39 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_17042d8c7761266a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_17042d8c7761266a.gif"]]
40
41 Figure 4-2 VD2B servo drive main circuit terminal distribution
42
43 (% class="table-bordered" %)
44 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
45 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="3" %)(((
46 Three-phase 220V AC input is connected to L1, L2, L3;
47
48 Single-phase 220V AC input is connected to L1 and L3.
49 )))
50 |(% style="text-align:center; vertical-align:middle" %)L2
51 |(% style="text-align:center; vertical-align:middle" %)L3
52 |(% style="text-align:center; vertical-align:middle" %)L1C|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Control power input terminal|(% rowspan="2" %)Single-phase 220V AC input is connected to L1C and L2C.
53 |(% style="text-align:center; vertical-align:middle" %)L2C
54 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
55 Use internal braking resistor: short-circuit C and D.
56
57 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
58 )))
59 |(% style="text-align:center; vertical-align:middle" %)C
60 |(% style="text-align:center; vertical-align:middle" %)D
61 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of motor to power the motor.
62 |(% style="text-align:center; vertical-align:middle" %)V
63 |(% style="text-align:center; vertical-align:middle" %)W
64 |(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
65
66 Table 4-2 The name and function of VD2B servo drive main circuit terminal
67
68 **VD2F servo drive main circuit terminal distribution**
69
70 (% style="text-align:center" %)
71 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6dd68f214c0f9f79.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6dd68f214c0f9f79.gif"]]
72
73 Figure 4-3 VD2F servo drive main circuit terminal distribution
74
75 (% class="table-bordered" %)
76 |(% style="text-align:center; vertical-align:middle" %)**Terminal number**|(% style="text-align:center; vertical-align:middle" %)**Terminal name**|(% style="text-align:center; vertical-align:middle" %)**Terminal function**
77 |(% style="text-align:center; vertical-align:middle" %)L1|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Power input terminal|(% rowspan="2" %)Connect single-phase 220V input power
78 |(% style="text-align:center; vertical-align:middle" %)L2
79 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Braking resistor terminal|(% rowspan="3" %)(((
80 Use internal braking resistor: short-circuit C and D.
81
82 Use external braking resistor: Please disconnect the short wire between C and D, and then connect the external braking resistor between P+ and C.
83 )))
84 |(% style="text-align:center; vertical-align:middle" %)C
85 |(% style="text-align:center; vertical-align:middle" %)D
86 |(% style="text-align:center; vertical-align:middle" %)P+|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Common DC bus terminal|(% rowspan="2" %)DC bus terminal of servo drive
87 |(% style="text-align:center; vertical-align:middle" %)N
88 |(% style="text-align:center; vertical-align:middle" %)U|(% rowspan="3" style="text-align:center; vertical-align:middle" %)Motor power line terminal|(% rowspan="3" %)Connect with the U, V and W of the motor to power the motor.
89 |(% style="text-align:center; vertical-align:middle" %)V
90 |(% style="text-align:center; vertical-align:middle" %)W
91 |(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Ground terminal|Grounding treatment of the servo drive.
92
93 Table 4-3 The name and function of VD2F servo drive main circuit terminal
94
95 == **Power wiring** ==
96
97 **VD2A drive single-phase 220V main circuit wiring**
98
99 (% style="text-align:center" %)
100 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9d2a6455f3f19347.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9d2a6455f3f19347.gif" data-xwiki-image-style-alignment="center" height="638" width="750"]]
101
102 Figure 4-4 VD2A drive single-phase 220V main circuit wiring
103
104 **VD2B drive single-phase 220V main circuit wiring**
105
106 (% style="text-align:center" %)
107 [[image:image-20220608141527-2.png||height="657" width="750"]]
108
109 Figure 4-5 VD2B drive single-phase 220V main circuit wiring
110
111 **VD2B drive three-phase 220V main circuit wiring**
112
113 (% style="text-align:center" %)
114 [[image:image-20220608141722-3.png||height="662" width="750"]]
115
116 Figure 4-6 VD2B drive three-phase 220V main circuit wiring
117
118 **VD2F drive single-phase 220V main circuit wiring**
119
120 (% style="text-align:center" %)
121 [[image:image-20220608141754-4.png||height="674" width="750"]]
122
123
124 Figure 4-7 VD2F drive single-phase 220V main circuit wiring
125
126 == **Precautions for main circuit wiring** ==
127
128 1. Do not connect the input power cord to the output terminals U, V, W, otherwise the servo drive will be damaged. When using the built-in braking resistor, C and D must be connected (factory default connection).
129 1. When the cables are bundled and used in pipes, etc., due to the deterioration of heat dissipation conditions, please consider the allowable current reduction rate.
130 1. When the temperature in the cabinet is higher than the cable temperature limit, please choose a cable with a larger cable temperature limit, and it is recommended that the cable wire use Teflon wire. Please pay attention to the warmth of the cable in the low temperature environment. Generally, the surface of the cable is easy to harden and break under the low temperature environment.
131 1. The bending radius of the cable should be more than 10 times the outer diameter of the cable itself to prevent the core of the cable from breaking due to long-term bending.
132
133 = **Power line connection of servo drive and servo motor** =
134
135 == **Power line** ==
136
137 Wecon VD2 series servo drive have 3 kinds of interface power cables: rectangular plug, aviation plug and in-line type.
138
139 (% class="table-bordered" %)
140 |(% style="text-align:center; vertical-align:middle" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle" %)**Terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Pin description**|(% style="text-align:center; vertical-align:middle" %)(((
141 **Motor**
142
143 **flange**
144 )))
145 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_621bbfcda5c57f86.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_621bbfcda5c57f86.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_621bbfcda5c57f86.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_621bbfcda5c57f86.gif"]]|(% style="text-align:center; vertical-align:middle" %)Rectangular plug(((
146 (% class="table-bordered" %)
147 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
148 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
149 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
150 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
151 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
152 )))|(% style="text-align:center; vertical-align:middle" %)(((
153 40
154
155 60
156
157 80
158 )))
159 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9335f5058d76f79a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9335f5058d76f79a.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_489b0453ee74953d.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_489b0453ee74953d.gif"]]|(% style="text-align:center; vertical-align:middle" %)Aviation plug(((
160 (% class="table-bordered" %)
161 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
162 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Black
163 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)Yellow-green
164 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
165 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Black
166 )))|(% style="text-align:center; vertical-align:middle" %)(((
167 110
168
169 130
170 )))
171 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_77117dacdd5935b9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_77117dacdd5935b9.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_7e9ea795751e109c.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_7e9ea795751e109c.gif"]]|(% style="text-align:center; vertical-align:middle" %)In-line type plug(((
172 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Color**
173 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)U|(% style="text-align:center; vertical-align:middle" %)Red
174 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)V|(% style="text-align:center; vertical-align:middle" %)White
175 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)W|(% style="text-align:center; vertical-align:middle" %)Black
176 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)PE|(% style="text-align:center; vertical-align:middle" %)Yellow-green
177 )))|(% style="text-align:center; vertical-align:middle" %)(((
178 60
179
180 80
181 )))
182
183 Table 4-4 Power cable servo motor side connector
184
185 ✎**Note:** The color of the lines is subject to the actual product. The lines described in this manual are all lines of Wecon.
186
187 == **Brake device cable** ==
188
189 (% class="table-bordered" %)
190 |(% colspan="2" style="text-align:center; vertical-align:middle; width:475px" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle; width:277px" %)**terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
191 |(% style="text-align:center; vertical-align:middle" %)WD series|(% style="text-align:center; vertical-align:middle; width:374px" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9be5695e6c0fd897.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_9be5695e6c0fd897.gif" height="103" width="128"]]|(% style="width:277px" %)(((
192 (% class="table-bordered" %)
193 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
194 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)BR+
195 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)BR-
196 )))|(% style="text-align:center; vertical-align:middle" %)(((
197 40
198
199 60
200
201 80
202 )))
203 |(% style="text-align:center; vertical-align:middle" %)WE series|(% style="text-align:center; vertical-align:middle; width:374px" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_576ebded84acbded.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_576ebded84acbded.gif" height="173" width="190"]]|(% style="width:277px" %)(((
204 (% class="table-bordered" %)
205 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
206 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DC 24V
207 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND
208 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)-
209 )))|(% style="text-align:center; vertical-align:middle" %)(((
210 80
211
212 110
213
214 130
215 )))
216
217 Table 4-5 Brake device cable
218
219 == **Encoder cable connection of servo drive and servo motor** ==
220
221 (% style="text-align:center" %)
222 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_2a7019b4f21f159e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_2a7019b4f21f159e.gif" height="324" width="857"]]
223
224 Figure 4-8 Encoder connection line wiring
225
226 (% class="table-bordered" %)
227 |(% style="text-align:center; vertical-align:middle" %)**Connector exterior**|(% style="text-align:center; vertical-align:middle" %)**Terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Pin description**
228 |(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_c798aa1eac035779.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_c798aa1eac035779.gif"]]|(% style="text-align:center; vertical-align:middle" %)[[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_671f87b1a542ce32.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_671f87b1a542ce32.gif"]]|(((
229 (% class="table-bordered" %)
230 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
231 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)E-
232 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+
233 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)E+|(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-
234 )))
235
236 Table 4-6 Encoder cable servo drive side connector
237
238 (% class="table-bordered" %)
239 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Connector exterior and terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
240 |(% style="text-align:center; vertical-align:middle" %)(((
241 (% style="text-align:center" %)
242 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_a41c00ba1133ea20.png?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_a41c00ba1133ea20.png" height="145" width="502"]]
243
244
245 )))|(((
246 (% style="text-align:center" %)
247 [[image:image-20220608142110-6.png||height="182" width="278"]]
248 )))|(% rowspan="3" style="text-align:center; vertical-align:middle" %)(((
249 40
250
251 60
252
253 80
254 )))
255 |(% style="text-align:center; vertical-align:middle" %)(((
256 (% style="text-align:center" %)
257 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_1ce0548bf47ef5ae.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_1ce0548bf47ef5ae.gif"]]
258 )))|(((
259 (% style="text-align:center" %)
260 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_4cb7be8f7bd5893e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_4cb7be8f7bd5893e.gif"]]
261 )))
262 |(% colspan="2" %)(((
263 (% class="table-bordered" %)
264 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
265 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
266 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)GND
267 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD+
268 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD-
269 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Shield
270 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Battery+
271 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
272 )))
273
274 Table 4-7 Absolute value encoder line connector (Rectangular plug)
275
276 (% class="table-bordered" %)
277 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle" %)**Motor side**
278 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Rectangular plug pin number**|(% style="text-align:center; vertical-align:middle" %)**Cable color**
279 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Blue
280 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Encoder power ground|(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Orange
281 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+|(% style="text-align:center; vertical-align:middle" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Green
282 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-|(% style="text-align:center; vertical-align:middle" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Brown
283 |(% style="text-align:center; vertical-align:middle" %)Shell|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)~-~-
284 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery+|(% style="text-align:center; vertical-align:middle" %)1*|(% style="text-align:center; vertical-align:middle" %)Pink
285 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery-|(% style="text-align:center; vertical-align:middle" %)2*|(% style="text-align:center; vertical-align:middle" %)Pink-Black
286
287 Table 4-8 Connection of encoder line pin
288
289 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
290
291 ✎ **Note: **The color of the line is subject to the actual product. The lines described in this manual are all lines of Wecon!
292
293 (% class="table-bordered" %)
294 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Connector shape and terminal pin distribution**|(% style="text-align:center; vertical-align:middle" %)**Motor flange**
295 |(% style="text-align:center; vertical-align:middle; width:531px" %)(((
296 (% style="text-align:center" %)
297 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_d450a92cc1507fcd.png?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_d450a92cc1507fcd.png" height="178" width="487"]]
298 )))|(% style="text-align:center; vertical-align:middle; width:530px" %)[[image:image-20220608142557-7.png]]|(% rowspan="3" style="text-align:center; vertical-align:middle" %)(((
299 110
300
301 130
302 )))
303 |(% style="width:531px" %)(((
304 (% style="text-align:center" %)
305 [[image:image-20220608144304-1.png]]
306 )))|(% style="width:530px" %)(((
307 (% style="text-align:center" %)
308 [[image:image-20220608144357-2.png]]
309 )))
310 |(% colspan="2" %)(((
311 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
312 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
313 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND
314 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD+
315 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD-
316 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Shield
317 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Battery+
318 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
319 )))
320
321 Table 4-9 Absolute value encoder line connector (Aviation plug)
322
323 (% class="table-bordered" %)
324 |(% colspan="2" style="text-align:center; vertical-align:middle; width:258px" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle; width:273px" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle; width:365px" %)**Motor side**
325 |(% style="text-align:center; vertical-align:middle; width:126px" %)**Pin number**|(% style="text-align:center; vertical-align:middle; width:128px" %)**Signal name**|(% style="text-align:center; vertical-align:middle; width:218px" %)(((
326 **Aviation plug pin number**
327 )))|(% style="text-align:center; vertical-align:middle; width:156px" %)**Cable  color**
328 |(% style="text-align:center; vertical-align:middle; width:126px" %)1|(% style="text-align:center; vertical-align:middle; width:128px" %)5V|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle; width:218px" %)7|(% style="text-align:center; vertical-align:middle; width:156px" %)Blue
329 |(% style="text-align:center; vertical-align:middle; width:126px" %)2|(% style="text-align:center; vertical-align:middle; width:128px" %)GND|(% style="text-align:center; vertical-align:middle; width:273px" %)Encoder power ground|(% style="text-align:center; vertical-align:middle; width:218px" %)8|(% style="text-align:center; vertical-align:middle; width:156px" %)Orange
330 |(% style="text-align:center; vertical-align:middle; width:126px" %)5|(% style="text-align:center; vertical-align:middle; width:128px" %)SD+|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle; width:218px" %)4|(% style="text-align:center; vertical-align:middle; width:156px" %)Green
331 |(% style="text-align:center; vertical-align:middle; width:126px" %)6|(% style="text-align:center; vertical-align:middle; width:128px" %)SD-|(% style="text-align:center; vertical-align:middle; width:273px" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle; width:218px" %)5|(% style="text-align:center; vertical-align:middle; width:156px" %)Brown
332 |(% style="text-align:center; vertical-align:middle; width:126px" %)Shell|(% style="text-align:center; vertical-align:middle; width:128px" %)Shield|(% style="text-align:center; vertical-align:middle; width:273px" %)Shield|(% style="text-align:center; vertical-align:middle; width:218px" %)3|(% style="text-align:center; vertical-align:middle; width:156px" %)-
333 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery+|(% style="text-align:center; vertical-align:middle; width:218px" %)1*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink
334 |(% style="text-align:center; vertical-align:middle; width:126px" %)-|(% style="text-align:center; vertical-align:middle; width:128px" %)-|(% style="text-align:center; vertical-align:middle; width:273px" %)Battery-|(% style="text-align:center; vertical-align:middle; width:218px" %)2*|(% style="text-align:center; vertical-align:middle; width:156px" %)Pink-Black
335
336 Table 4-10 Absolute encoder cable connector (aviation socket)
337
338 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
339
340 ✎ **Note: **The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
341
342 (% class="table-bordered" %)
343 |(% colspan="2" style="text-align:center; vertical-align:middle; width:791px" %)**Connector shape and terminal pin distribution**|(% style="text-align:center; vertical-align:middle; width:94px" %)(((
344 **Motor**
345
346 **flange**
347 )))
348 |(% style="text-align:center; vertical-align:middle; width:544px" %)(((
349 (% style="text-align:center" %)
350 [[image:image-20220608144543-3.png||height="203" width="495"]]
351 )))|(% style="width:563px" %)(((
352 (% style="text-align:center" %)
353 [[image:image-20220608144728-6.png]]
354 )))|(% rowspan="3" style="text-align:center; vertical-align:middle; width:94px" %)(((
355 60
356
357 80
358 )))
359 |(% style="text-align:center; vertical-align:middle; width:544px" %)(((
360 (% style="text-align:center" %)
361 [[image:image-20220608144619-5.png||height="147" width="353"]]
362 )))|(% style="width:563px" %)(((
363 (% style="text-align:center" %)
364 [[image:image-20220608144750-7.png||height="137" width="358"]]
365 )))
366 |(% colspan="2" style="width:791px" %)(((
367 (% class="table-bordered" %)
368 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
369 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)5V
370 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND
371 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD+
372 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)SD-
373 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Shield
374 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Battery+
375 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Battery-
376 )))
377
378 Table 4-11 Absolute encoder cable connector (in-line type)
379
380 (% class="table-bordered" %)
381 |(% colspan="2" style="text-align:center; vertical-align:middle" %)**Drive side J1394**|(% rowspan="2" style="text-align:center; vertical-align:middle" %)**Description**|(% colspan="2" style="text-align:center; vertical-align:middle" %)**Motor side**
382 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)(((
383 **In-line plug**
384
385 **pin number**
386 )))|(% style="text-align:center; vertical-align:middle" %)**Cable color**
387 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)5V|(% style="text-align:center; vertical-align:middle" %)Encoder +5v power|(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Blue
388 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Encoder power ground|(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Orange
389 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)SD+|(% style="text-align:center; vertical-align:middle" %)Serial communication signal +|(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Green
390 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)SD-|(% style="text-align:center; vertical-align:middle" %)Serial communication signal -|(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Brown
391 |(% style="text-align:center; vertical-align:middle" %)Shell|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)Shield|(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)-
392 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery+|(% style="text-align:center; vertical-align:middle" %)3*|(% style="text-align:center; vertical-align:middle" %)Brown
393 |(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)Battery-|(% style="text-align:center; vertical-align:middle" %)2*|(% style="text-align:center; vertical-align:middle" %)Black
394
395 The pin with “*” indicates the signal line of encoder battery. If the multi-turn battery memory function is not used, you don’t need to connect the signal lines. It is only used as single turn encoder line at this time.
396
397 ✎**Note:** The color of the cable is subject to the actual product. The cables described in this manual are all cables of Wecon!
398
399 = **Servo drive control input and output wiring** =
400
401 == **CN2 pin distribution** ==
402
403 **VD2A and VD2B servo drive control input and output pin distribution (CN2 interface)**
404
405 (% style="text-align:center" %)
406 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_e8200287ad0381e3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_e8200287ad0381e3.gif"]]
407
408 Figure 4-9 VD2A and VD2B servo drive control input and output pin distribution
409
410 (% class="table-bordered" %)
411 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
412 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)16|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)31|(% style="text-align:center; vertical-align:middle" %)-
413 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)AI_2+|(% style="text-align:center; vertical-align:middle" %)17|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)32|(% style="text-align:center; vertical-align:middle" %)AI_1+
414 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)AI_2-|(% style="text-align:center; vertical-align:middle" %)18|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)33|(% style="text-align:center; vertical-align:middle" %)AI_1-
415 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DO1-|(% style="text-align:center; vertical-align:middle" %)19|(% style="text-align:center; vertical-align:middle" %)DO3-|(% style="text-align:center; vertical-align:middle" %)34|(% style="text-align:center; vertical-align:middle" %)GND
416 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DO1+|(% style="text-align:center; vertical-align:middle" %)20|(% style="text-align:center; vertical-align:middle" %)DO3+|(% style="text-align:center; vertical-align:middle" %)35|(% style="text-align:center; vertical-align:middle" %)-
417 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO2-|(% style="text-align:center; vertical-align:middle" %)21|(% style="text-align:center; vertical-align:middle" %)DO4-|(% style="text-align:center; vertical-align:middle" %)36|(% style="text-align:center; vertical-align:middle" %)-
418 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2+|(% style="text-align:center; vertical-align:middle" %)22|(% style="text-align:center; vertical-align:middle" %)DO4+|(% style="text-align:center; vertical-align:middle" %)37|(% style="text-align:center; vertical-align:middle" %)-
419 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)23|(% style="text-align:center; vertical-align:middle" %)DI5|(% style="text-align:center; vertical-align:middle" %)38|(% style="text-align:center; vertical-align:middle" %)-
420 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)24|(% style="text-align:center; vertical-align:middle" %)DI6|(% style="text-align:center; vertical-align:middle" %)39|(% style="text-align:center; vertical-align:middle" %)-
421 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)25|(% style="text-align:center; vertical-align:middle" %)DI7|(% style="text-align:center; vertical-align:middle" %)40|(% style="text-align:center; vertical-align:middle" %)SIGN-
422 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)26|(% style="text-align:center; vertical-align:middle" %)DI8|(% style="text-align:center; vertical-align:middle" %)41|(% style="text-align:center; vertical-align:middle" %)SIGN+
423 |(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)27|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)42|(% style="text-align:center; vertical-align:middle" %)PULS-
424 |(% style="text-align:center; vertical-align:middle" %)13|(% style="text-align:center; vertical-align:middle" %)PAO-|(% style="text-align:center; vertical-align:middle" %)28|(% style="text-align:center; vertical-align:middle" %)PAO+|(% style="text-align:center; vertical-align:middle" %)43|(% style="text-align:center; vertical-align:middle" %)PULS+
425 |(% style="text-align:center; vertical-align:middle" %)14|(% style="text-align:center; vertical-align:middle" %)PBO-|(% style="text-align:center; vertical-align:middle" %)29|(% style="text-align:center; vertical-align:middle" %)PBO+|(% style="text-align:center; vertical-align:middle" %)44|(% style="text-align:center; vertical-align:middle" %)PL
426 |(% style="text-align:center; vertical-align:middle" %)15|(% style="text-align:center; vertical-align:middle" %)PZO-|(% style="text-align:center; vertical-align:middle" %)30|(% style="text-align:center; vertical-align:middle" %)PZO+|(% style="text-align:center; vertical-align:middle" %)~-~-|(% style="text-align:center; vertical-align:middle" %)~-~-
427
428 Table 4-12 CN2 interface definition of VD2A and VD2B servo drive
429
430 **VD2F servo drive control input and output pin distribution (CN2 interface)**
431
432 (% style="text-align:center" %)
433 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_55a725365ef15a86.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_55a725365ef15a86.gif" height="255" width="92"]]
434
435 Figure 4-10 VD2F servo drive control input and output pin distribution
436
437 (% class="table-bordered" %)
438 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**
439 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DO3|(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI4
440 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)DO1|(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2
441 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)PL
442 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)PULS+
443 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)13|(% style="text-align:center; vertical-align:middle" %)PULS-
444 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO4|(% style="text-align:center; vertical-align:middle" %)14|(% style="text-align:center; vertical-align:middle" %)SIGN+
445 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2|(% style="text-align:center; vertical-align:middle" %)15|(% style="text-align:center; vertical-align:middle" %)SIGN-
446 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DOCOM|(% style="text-align:center; vertical-align:middle" %)-|(% style="text-align:center; vertical-align:middle" %)-
447
448 Table 4-13 CN2 interface definition of VD2F servo drive
449
450 == **Wiring diagram of each mode** ==
451
452 **VD2A and VD2B servo drive**
453
454 (% style="text-align:center" %)
455 [[image:4-11.jpg||height="961" width="750"]]
456
457 Figure 4-11 Wiring diagram of each mode
458
459 ✎**Note:** Please refer to "[[__4.4.1 __Table 4-12 CN2 interface definition of VD2A and VD2B servo drive>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_e8200287ad0381e3.gif?rev=1.1]]" for the pin numbers in the figure.
460
461 **VD2F servo drive**
462
463 (% style="text-align:center" %)
464 [[image:image-20220608145058-9.png]]
465
466 Figure 4-12 Position pulse mode wiring
467
468 ✎**Note:** Please refer to "[[__4.4.1 __Table 4-13 CN2 interface definition of VD2F servo drive>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_55a725365ef15a86.gif?rev=1.1]]" for the pin numbers in the figure.
469
470 == **Position instruction input signal** ==
471
472 (% class="table-bordered" %)
473 |(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**VD2A and VD2B pin number**|(% style="text-align:center; vertical-align:middle" %)**VD2F pin number**|(% style="text-align:center; vertical-align:middle" %)**Function**
474 |(% style="text-align:center; vertical-align:middle" %)PULS+|(% style="text-align:center; vertical-align:middle" %)43|(% style="text-align:center; vertical-align:middle" %)12|(% rowspan="4" %)(((
475 Low-speed pulse input modes: differential input, open collector.
476
477 There are three types of input pulse:
478
479 1. Direction + pulse (positive logic);
480 1. CW/CCW;
481 1. A and B phase quadrature pulses (4 times the
482
483 frequency).
484 )))
485 |(% style="text-align:center; vertical-align:middle" %)PULS-|(% style="text-align:center; vertical-align:middle" %)42|(% style="text-align:center; vertical-align:middle" %)13
486 |(% style="text-align:center; vertical-align:middle" %)SIGN+|(% style="text-align:center; vertical-align:middle" %)41|(% style="text-align:center; vertical-align:middle" %)14
487 |(% style="text-align:center; vertical-align:middle" %)SIGN-|(% style="text-align:center; vertical-align:middle" %)40|(% style="text-align:center; vertical-align:middle" %)15
488 |(% style="text-align:center; vertical-align:middle" %)PL|(% style="text-align:center; vertical-align:middle" %)44|(% style="text-align:center; vertical-align:middle" %)11|External power input interface for instruction pulse.
489
490 Table 4-14 Position instruction signal description
491
492 The instruction pulse and sign output circuit on the host device side can be selected from differential output or open collector output. The maximum input frequency is shown in the table.
493
494 (% class="table-bordered" %)
495 |(% style="text-align:center; vertical-align:middle" %)**Pulse method**|(% style="text-align:center; vertical-align:middle" %)**Difference**|(% style="text-align:center; vertical-align:middle" %)**Open collector**
496 |(% style="text-align:center; vertical-align:middle" %)Maximum frequency|(% style="text-align:center; vertical-align:middle" %)500KHz|(% style="text-align:center; vertical-align:middle" %)200KHz
497
498 **Differential input**
499
500 The connection of differential input is shown in Figure 4-9.
501
502 [[image:image-20220609112758-1.png]]
503
504 (% style="text-align:center" %)
505 [[image:image-20220609112049-1.png]]
506
507 Figure 4-13 VD2A and VD2B servo drive differential input connection
508
509 (% style="text-align:center" %)
510 [[image:image-20220609110918-6.jpeg||height="313" width="512"]]
511
512 Figure 4-14 VD2F servo drive differential input connection
513
514 **Open collector input**
515
516 1.Open collector input connection
517
518 (% style="text-align:center" %)
519 [[image:image-20220609111236-7.jpeg||height="441" width="610"]]
520
521 Figure 4-15 VD2A and VD2B servo drive open collector input connection
522
523 (% style="text-align:center" %)
524 [[image:image-20220609111352-8.jpeg||height="431" width="600"]]
525
526 Figure 4-16 VD2F servo drive open collector input connection
527
528 2.NPN and PNP wiring
529
530 (% class="table-bordered" %)
531 |(% style="width:597px" %)(((
532 (% style="text-align:center" %)
533 [[image:image-20220609111643-11.jpeg]]
534 )))|(% style="width:478px" %)(((
535 (% style="text-align:center" %)
536 [[image:image-20220609111654-12.jpeg]]
537 )))
538 |(% style="text-align:center; vertical-align:middle; width:597px" %)NPN|(% style="text-align:center; vertical-align:middle; width:478px" %)PNP
539 |(% colspan="2" style="text-align:center; vertical-align:middle" %)Figure 4-17 Triode Wiring
540
541 == **Analog input signal** ==
542
543 The analog input signal is only supported by VD2A and VD2B servo drives.
544
545 (% class="table-bordered" %)
546 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Function**
547 |(% style="text-align:center; vertical-align:middle" %)32|(% style="text-align:center; vertical-align:middle" %)AI_1+|(% rowspan="2" %)(((
548 AI_1 analog input signal, resolution 12-bit.
549
550 Input voltage range: -10V to +10V.
551 )))
552 |(% style="text-align:center; vertical-align:middle" %)33|(% style="text-align:center; vertical-align:middle" %)AI_1-
553 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)AI_2+|(% rowspan="2" %)(((
554 AI_2 analog input signal, resolution 12-bit.
555
556 Input voltage range: -10V to +10V.
557 )))
558 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)AI_2-
559 |(% style="text-align:center; vertical-align:middle" %)17|(% style="text-align:center; vertical-align:middle" %)GND|(% rowspan="2" %)Analog input signal ground.
560 |(% style="text-align:center; vertical-align:middle" %)34|(% style="text-align:center; vertical-align:middle" %)GND
561
562 Table 4-15 Analog input signal description
563
564 (% style="text-align:center" %)
565 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_189eff54d0bbd5af.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_189eff54d0bbd5af.gif"]]
566
567 Figure 4-18 Analog input wiring
568
569
570 == **Digital input and output signals** ==
571
572 **VD2A and VD2B servo drives**
573
574 (% class="table-bordered" %)
575 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Signal name**|(% style="text-align:center; vertical-align:middle" %)**Default function**
576 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
577 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
578 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
579 |(% style="text-align:center; vertical-align:middle" %)12|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
580 |(% style="text-align:center; vertical-align:middle" %)23|(% style="text-align:center; vertical-align:middle" %)DI5|(% style="text-align:center; vertical-align:middle" %)Inverted instruction
581 |(% style="text-align:center; vertical-align:middle" %)24|(% style="text-align:center; vertical-align:middle" %)DI6|(% style="text-align:center; vertical-align:middle" %)Instruction pulse prohibited input
582 |(% style="text-align:center; vertical-align:middle" %)25|(% style="text-align:center; vertical-align:middle" %)DI7|(% style="text-align:center; vertical-align:middle" %)Not used
583 |(% style="text-align:center; vertical-align:middle" %)26|(% style="text-align:center; vertical-align:middle" %)DI8|(% style="text-align:center; vertical-align:middle" %)Not used
584 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DICOM|(% style="text-align:center; vertical-align:middle" %)24V
585 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DO1-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Rotation detection
586 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DO1+
587 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO2-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Faults signal
588 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2+
589 |(% style="text-align:center; vertical-align:middle" %)19|(% style="text-align:center; vertical-align:middle" %)DO3-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Servo is ready
590 |(% style="text-align:center; vertical-align:middle" %)20|(% style="text-align:center; vertical-align:middle" %)DO3+
591 |(% style="text-align:center; vertical-align:middle" %)21|(% style="text-align:center; vertical-align:middle" %)DO4-|(% rowspan="2" style="text-align:center; vertical-align:middle" %)Positioning completed
592 |(% style="text-align:center; vertical-align:middle" %)22|(% style="text-align:center; vertical-align:middle" %)DO4+
593
594 Table 4-16 DI/DO signal description
595
596 **Digital input circuit**
597
598 1.When the control device(HMI/PLC) is relay output
599
600 (% style="text-align:center" %)
601 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_df384a263bb6da8e.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_df384a263bb6da8e.gif"]]
602
603 Figure 4-19 Relay output
604
605 2.When the control device(HMI/PLC) is open collector output
606
607 (% style="text-align:center" %)
608 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_bd7bc86ca63a344b.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_bd7bc86ca63a344b.gif"]]
609
610 Figure 4-20 Open collector output
611
612 **Digital output circuit**
613
614 1.When the control device(HMI/PLC) is relay input
615
616 (% style="text-align:center" %)
617 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_f16ac03591f1a0a.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_f16ac03591f1a0a.gif"]]
618
619 Figure 4-21 Relay input
620
621 2.When the control device(HMI/PLC) is optocoupler input
622
623 (% style="text-align:center" %)
624 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_d1e75001d4cc31f9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_d1e75001d4cc31f9.gif"]]
625
626 Figure 4-22 Optocoupler input
627
628 **VD2F servo drive**
629
630 (% class="table-bordered" %)
631 |(% style="text-align:center; vertical-align:middle" %)**Pin number**|(% style="text-align:center; vertical-align:middle" %)**Pin name**|(% style="text-align:center; vertical-align:middle" %)**Default function**
632 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)DI1|(% style="text-align:center; vertical-align:middle" %)Servo enable
633 |(% style="text-align:center; vertical-align:middle" %)10|(% style="text-align:center; vertical-align:middle" %)DI2|(% style="text-align:center; vertical-align:middle" %)Faults and alarms clearance
634 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)DI3|(% style="text-align:center; vertical-align:middle" %)Forward drive prohibited
635 |(% style="text-align:center; vertical-align:middle" %)9|(% style="text-align:center; vertical-align:middle" %)DI4|(% style="text-align:center; vertical-align:middle" %)Reverse drive prohibited
636 |(% style="text-align:center; vertical-align:middle" %)11|(% style="text-align:center; vertical-align:middle" %)SS|(% style="text-align:center; vertical-align:middle" %)Power input (24V)
637 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)DO1|(% style="text-align:center; vertical-align:middle" %)Rotation detection
638 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)DO2|(% style="text-align:center; vertical-align:middle" %)Fault signal
639 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)DO3|(% style="text-align:center; vertical-align:middle" %)Servo is ready
640 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)DO4|(% style="text-align:center; vertical-align:middle" %)Positioning completed
641 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)DOCOM|(% style="text-align:center; vertical-align:middle" %)Do common terminal
642
643 Table 4-17 DI/DO signal description
644
645 **Digital input circuit**
646
647 1.When the control device(HMI/PLC) is relay output
648
649 (% style="text-align:center" %)
650 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6861cbbee65afc3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6861cbbee65afc3.gif"]]
651
652 Figure 4-23 Relay output
653
654 2.When the control device(HMI/PLC) is open collector output
655
656 (% style="text-align:center" %)
657 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_ce4de1a5701b382d.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_ce4de1a5701b382d.gif"]]
658
659 Figure 4-24 Open collector output
660
661 **Digital output circuit**
662
663 1.When the control device(HMI/PLC) is relay input
664
665 (% style="text-align:center" %)
666 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_1416274c5f871283.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_1416274c5f871283.gif"]]
667
668 Figure 4-25 Relay output
669
670 2.When the control device(HMI/PLC) is optocoupler input
671
672 (% style="text-align:center" %)
673 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3ade436b150a75d9.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_3ade436b150a75d9.gif"]]
674
675 Figure 4-26 Optocoupler input
676
677 == **Brake wiring** ==
678
679 The brake is a mechanism that prevents the servo motor shaft from moving when the servo drive is in a non-running state, so that the motor remains in position lock, so that the moving part of the machinery will not move due to self-weight or external force.
680
681 Brake input signal is no polar. You need to use 24V power . The standard wiring between brake signal BK and brake power is as below.
682
683 (% style="text-align:center" %)
684 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_8000f59dd6848011.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_8000f59dd6848011.gif"]]
685
686 Figure 4-27 Brake wiring (three-phase 220V input)
687
688 (% style="text-align:center" %)
689 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_dcaf5f24afc3957b.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_dcaf5f24afc3957b.gif"]]
690
691 Figure 4-28 Brake wiring (single-phase 220V input)
692
693 = **Communication signal wiring** =
694
695 Wecon VD2 series servo drive supports two communication modes: RS-422 and RS-485. The exterior of communication terminal is shown in Figure 4-29.
696
697 (% style="text-align:center" %)
698 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_36a1ac5641d607b2.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_36a1ac5641d607b2.gif" height="159" width="157"]]
699
700 Figure 4-29 communication port exterior and pin definition
701
702 == **Communication signal connector** ==
703
704 **(1) VD2A and VD2B servo drive**
705
706 The signal connectors exterior of RS422 and RS485 communication methods are shown in Figure 4-19 (a) and (b) respectively.
707
708 (% class="table-bordered" %)
709 |(((
710 (% style="text-align:center" %)
711 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_6017da4ef2b79ce3.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_6017da4ef2b79ce3.gif"]]
712 )))|(((
713 (% style="text-align:center" %)
714 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_54ecc0baf9dc3fe8.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_54ecc0baf9dc3fe8.gif"]]
715 )))
716 |(% style="text-align:center; vertical-align:middle" %)(A) RS422 communication|(% style="text-align:center; vertical-align:middle" %)(B) RS485 communication
717 |(% colspan="2" style="text-align:center; vertical-align:middle" %)Figure 4-30 VD2A and VD2B servo drive communication signal connector exterior
718
719 **(2) VD2F servo drive**
720
721 The CN3 and CN4 interfaces support RS422 and RS485 communication methods. The exterior of the communication signal connector is shown in __[[Figure 4-31>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3036b46714cd6b88.gif?rev=1.1]]__. __[[Table 4-18>>http://13.229.109.52:8080/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/04%20Wiring/#HCommunicationsignalconnector]]__ is the pin definition corresponding to the two communications.
722
723 (% style="text-align:center" %)
724 [[image:http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_3036b46714cd6b88.gif?rev=1.1||alt="Wecon VD2 SA Series Servo Drives Manual (Full V1.1)_html_3036b46714cd6b88.gif"]]
725
726 Figure 4-31 VD2F servo drive communication signal connector exterior
727
728 (% class="table-bordered" %)
729 |(% colspan="2" style="text-align:center; vertical-align:middle" %)(((
730 **Communication method Pin number and function**
731 )))|(% style="text-align:center; vertical-align:middle" %)**Pin name corresponding to RS422 communication**|(% style="text-align:center; vertical-align:middle" %)**Pin name corresponding to RS485 communication**
732 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal|(% style="text-align:center; vertical-align:middle" %)RX-|(% style="text-align:center; vertical-align:middle" %)485-
733 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal|(% style="text-align:center; vertical-align:middle" %)RX+|(% style="text-align:center; vertical-align:middle" %)485+
734 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)Computer receives negative terminal|(% style="text-align:center; vertical-align:middle" %)TX-|(% style="text-align:center; vertical-align:middle" %)-
735 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)Ground terminal|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)GND
736 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
737 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)Computer receives positive terminal|(% style="text-align:center; vertical-align:middle" %)TX+|(% style="text-align:center; vertical-align:middle" %)-
738 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
739 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)Not used|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)-
740
741 Table 4-18 VD2F servo drive communication signal connector pin definition
742
743 == **Host computer communication connection** ==
744
745 VD2A and VD2B servo drives communicate with the host computer via the CN3 interface by RS422 communication. Table 4-9 is the pin definition of the CN3 interface. The communication diagrams of VD2A and VD2B servo drives and host computer are shown in __[[Figure 4-32>>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_2a6d3dc0bc5368b7.gif?rev=1.1]]__ and __[[Figure 4-33 >>http://docs.we-con.com.cn/wiki/servo/download/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/WebHome/Wecon%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29_html_9d156f3c473d7fc.gif?rev=1.1]]__respectively.
746
747 (% class="table-bordered" %)
748 |(% style="text-align:center; vertical-align:middle" %)**Pin**|(% style="text-align:center; vertical-align:middle" %)**Name**|(% style="text-align:center; vertical-align:middle" %)**Function description**
749 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)RX-|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal (drive receives negative)
750 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)RX+|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal (drive receives positive)
751 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)TX-|(% style="text-align:center; vertical-align:middle" %)Computer receives negative terminal (drive sends negative)
752 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
753 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
754 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)TX+|(% style="text-align:center; vertical-align:middle" %)Computer receives positive terminal (drive sends positive)
755 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
756 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
757
758 Table 4-19 The pin definition of CN3 interface
759
760 (% style="text-align:center" %)
761 [[image:image-20220608145637-11.png]]
762
763 Figure 4-32 The Connection between VD2A drive and PC
764
765 (% style="text-align:center" %)
766 [[image:image-20220608145828-14.png]]
767
768 Figure 4-33 The connection between VD2B drive and PC
769
770 VD2F servo drive communicates with the host computer via the CN3 or CN4 interface byRS422 communication. The communication diagrams of VD2F servo drive and host computer are shown in __[[Figure 4-34>>url:http://docs.we-con.com.cn/wiki/servo/view/2.%20User%20Manual/06%20VD2%20SA%20Series%20Servo%20Drives%20Manual%20%28Full%20V1.1%29/#F434]]__ respectively.
771
772 (% style="text-align:center" %)
773 [[image:image-20220608145750-13.png]]
774
775 Figure 4-34 The connection between VD2F drive and PC
776
777 == **PLC communication connection** ==
778
779 VD2A and VD2B servo drives communicate with the PLC via CN5 or CN6 interface (located on the top of servo drive) by RS485 communication.
780
781 VD2F servo drive communicates with the PLC via CN3 or CN4 interface by RS485 communication.
782
783 (% class="table-bordered" %)
784 |(% style="text-align:center; vertical-align:middle" %)**Pin**|(% style="text-align:center; vertical-align:middle" %)**Name**|(% style="text-align:center; vertical-align:middle" %)**Function description**
785 |(% style="text-align:center; vertical-align:middle" %)1|(% style="text-align:center; vertical-align:middle" %)485+|(% style="text-align:center; vertical-align:middle" %)Computer sends negative terminal (drive receives negative)
786 |(% style="text-align:center; vertical-align:middle" %)2|(% style="text-align:center; vertical-align:middle" %)485-|(% style="text-align:center; vertical-align:middle" %)Computer sends positive terminal (drive receives positive)
787 |(% style="text-align:center; vertical-align:middle" %)3|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
788 |(% style="text-align:center; vertical-align:middle" %)4|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
789 |(% style="text-align:center; vertical-align:middle" %)5|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
790 |(% style="text-align:center; vertical-align:middle" %)6|(% style="text-align:center; vertical-align:middle" %)NC|(% style="text-align:center; vertical-align:middle" %)Not used
791 |(% style="text-align:center; vertical-align:middle" %)7|(% style="text-align:center; vertical-align:middle" %)Reserved|(% style="text-align:center; vertical-align:middle" %)Reserved
792 |(% style="text-align:center; vertical-align:middle" %)8|(% style="text-align:center; vertical-align:middle" %)GND|(% style="text-align:center; vertical-align:middle" %)Ground terminal
793
794 Table 4-20 The pin definition of CN5/CN6 interface