Wiki source code of Mitsubishi

Version 84.1 by Joe on 2024/04/29 14:40

version	line-number	content
40.1	1	== FX3U,3G,3GA Serial ==
2.1	2
	3	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
	4
38.1	5	V-BOX Settings
2.1	6
	7	\|Item\|Settings\|Note
	8	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	9	\|Connection\|RS422/RS485/RS232\|
	10	\|Baud rate\|9600~~115200\|
	11	\|Data bit\|7/8\|
	12	\|Parity\|EVEN/Odd/None\|
	13	\|Stop bit\|1/2\|
	14	\|PLC station No.\|1~~255\|
	15
58.1	16	(% style="text-align:center" %)
	17	[[image:三菱 FX3U 串口协议配置.png]]
	18
38.1	19	Address List
2.1	20
67.1	21	\|Type\|Device registers\|Format\|Range\|Note
83.16	22	\|(% rowspan="7" %)Bit\|X\|X o\|0~~303237\|
67.1	23	\|Y\|Y o\|0~~303237\|
	24	\|M\|M d\|0~~99999\|
	25	\|T\|T d\|0~~99999\|
	26	\|C\|C d\|0~~99999\|
	27	\|S\|S d\|0~~99999\|
	28	\|SM\|SM d\|8000~~9999\|
83.16	29	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
67.1	30	\|Y\|Y o\|0~~303237\|
	31	\|M\|M d\|0~~99999\|
	32	\|T\|T d\|0~~99999\|
	33	\|C\|C d\|0~~199\|
	34	\|D\|D d\|0~~7999\|
	35	\|S\|S d\|0~~99999\|
	36	\|SD\|SD d\|8000~~9999\|
2.1	37
42.1	38	PLC Setting
2.1	39
42.1	40	Open GX Works2, create a new PLC project or open the project that has been created.
	41	Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].
	42
	43	(% style="text-align:center" %)
77.1	44	[[image:GX2.png]]
	45
	46	(% style="text-align:center" %)
42.1	47	[[image:1.2.png]]
	48
	49	PLC Default Parameters:
	50	[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
	51	Note:The serial port parameters should be set depending on field requirements
	52
	53	PC and PLC connection:
	54
	55	[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]
	56
	57	(% style="text-align:center" %)
	58	[[image:1.5.1.png]]
	59
	60	Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”
	61
	62	(% style="text-align:center" %)
	63	[[image:1.5.2.png]]
	64
77.1	65	[PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]
	66
	67	(% style="text-align:center" %)
78.1	68	[[image:FX3U串口下载.png]]
77.1	69
42.1	70	Cable Wiring
	71
38.1	72	RS422
2.1	73
38.1	74	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e904556bb758dfe.png\|\|alt="image-20220825103421-5.png" height="296" width="715"]]
2.1	75
38.1	76	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_860bcf87f6ca7b98.png\|\|alt="image-20220825100845-4.png" height="246" width="419"]]
2.1	77
43.1	78	== FX NOPROTOCOL ==
	79
	80	Mitsubishi FX3G-RS232-BD
	81
	82	V-Box Settings
	83
	84	\|=Item\|=Settings\|=Note
	85	\|Protocol\|Mitsubishi FX NOPROTOCOL\|
	86	\|Connection\|RS232\|
	87	\|Baud rate\|9600\|
	88	\|Data bit\|7\|
	89	\|Parity\|EVEN\|
	90	\|Stop bit\|1\|
	91	\|PLC station No.\|0\|
	92
	93	(% style="text-align:center" %)
	94	[[image:三菱 FN盒子通讯配置.png]]
	95
	96	Address List
	97
68.1	98	\|=Type\|=Device registers\|=Format\|=Range\|=Note
	99	\|(% rowspan="8" %)Bit\|X\|X o\|0~~303237\|
	100	\|Y\|Y o\|0~~303237\|
	101	\|M\|M d\|0~~99999\|
	102	\|T\|T d\|0~~99999\|
	103	\|C\|C d\|0~~99999\|
	104	\|S\|S d\|0~~99999\|
	105	\|SM\|SM d\|8000~~9999\|
	106	\|Lamp\|Lamp d\|0~~0\|
	107	\|(% rowspan="8" %)Word\|X\|X o\|0~~303237\|
	108	\|Y\|Y o\|0~~303237\|
	109	\|M\|M d\|0~~99999\|
	110	\|T\|T d\|0~~99999\|
	111	\|C\|C d\|0~~199\|
	112	\|D\|D d\|0~~7999\|
	113	\|S\|S d\|0~~99999\|
	114	\|SD\|SD d\|8000~~9999\|
43.1	115
45.1	116	Cable Wiring
43.1	117
44.1	118	[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_1717efe8d969a43c.png]]
	119
41.1	120	== FX3U Ethernet ==
2.1	121
	122	Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L
	123
41.1	124	V-BOX Settings
2.1	125
	126	\|Items\|Settings\|Note
	127	\|Protocol\|Mitsubishi FX3U\|
	128	\|Connection\|Ethernet\|
	129	\|Port No.\|5009\|Must be the same as the PLC setting
	130	\|PLC station No.\|0\|
	131
60.1	132	(% style="text-align:center" %)
	133	[[image:三菱 FX3U 以太网协议配置.png]]
57.1	134
41.1	135	Address List
2.1	136
69.1	137	\|Type\|Device registers\|Format\|Range\|Note
	138	\|(% rowspan="7" %)Bit\|X\|X OOO\|0~~377\|
	139	\|Y\|Y OOO\|0~~377\|
	140	\|M\|M DDDD\|0~~7679\|
	141	\|SM\|SM DDDD\|8000~~8511\|
	142	\|S\|S DDDD\|0~~4095\|
	143	\|TS\|TS DDD\|0~~511\|
	144	\|CS\|CS DDD\|0~~255\|
	145	\|(% rowspan="5" %)Word\|CN\|CN DDD\|0~~199\|
	146	\|TN\|TN DDD\|0~~511\|
	147	\|D\|D DDDD\|0~~7999\|
	148	\|SD\|SD DDDD\|8000~~8511\|
	149	\|R\|R DDDDD\|0~~32767\|
2.1	150
41.1	151	Ethernet Module Settings
2.1	152
	153	FX3U-ENET-L module configuration
	154	Set up the FX3U-ENET-L Ethernet module settings as follows.
	155	Select the module location, which in this document is Module 0.
	156
41.1	157	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_949d5d77c1d9cf1e.png\|\|alt="image-20221116105850-1.png" height="573" width="706"]]
2.1	158
	159	Select "Operational setting" to enter the following screen.
	160
	161	The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.
	162
83.18	163	(% style="text-align:center" %)
	164	[[image:894qM2hnau.png]]
2.1	165
	166	Select "Open setting" to enter the setting interface, the settings are as follows.
	167
	168	The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the
	169
	170	Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.
	171
41.1	172	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7c01ac15090fcc5b.png\|\|alt="image-20221116110802-1.png" height="549" width="706"]]
2.1	173
	174	Click on "transter setup" - "PC side I/F setting", see the following figure.
	175
	176	After setting, the first download must use the programming cable, as shown in the figure; after that, can
	177
	178	use the IP set in the "Ethernet board" to communicate directly with the network cable.
	179
83.18	180	(% style="text-align:center" %)
	181	[[image:xzZboZHffh.png]]
2.1	182
83.18	183	(% style="text-align:center" %)
	184	[[image:ivWMdrv1Gh.png]]
2.1	185
83.18	186	(% style="text-align:center" %)
	187	[[image:qoQNWSBoEQ.png]]
	188
	189
41.1	190	PLC Settings (GX Works 2)
2.1	191
	192	Create a blank FX5U project
	193
	194	Find Current Connection in the navigation
	195
41.1	196	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d2a46ba9c005cf38.png\|\|alt="image-20221116111427-1.png" height="421" width="705"]]
2.1	197
	198	Select Connection Channel List
	199
	200	Select Ethernet board communication
	201
41.1	202	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_8f49721a3e5b0ef9.png\|\|alt="image-20221116111451-2.png" height="421" width="705"]]
2.1	203
	204	Select Ethernet Module
	205	Set the IP address of the PLC
	206
41.1	207	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1e9a9e29a46a1041.png\|\|alt="image-20221116111509-3.png" height="666" width="699"]]
2.1	208
	209	Read or write PLC data, in this document is read
	210
	211	{{id name="Iimage-20221116111651-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_e3d629103727a423.png\|\|alt="image-20221116111651-4.png" height="416" width="697"]]
	212
41.1	213	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_7f29923ebcb670d1.png\|\|alt="image-20221116111727-5.png" height="416" width="697"]]
2.1	214
46.1	215	== FX5U Serial ==
2.1	216
	217	Mitsubishi FX5U series PLC
	218
46.1	219	V-BOX Settings
2.1	220
	221	\|Item\|Settings\|Note
	222	\|Protocol\|Mitsubishi FX5U\|
	223	\|Connection\|RS422/RS485\|
	224	\|Baud rate\|9600\|
	225	\|Data bit\|7\|
	226	\|Parity\|Odd\|
	227	\|Stop bit\|1\|
	228	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	229
54.1	230	(% style="text-align:center" %)
	231	[[image:三菱 FX5U 串口协议配置.png]]
	232
46.1	233	Address List
2.1	234
70.1	235	\|Type\|Device registers\|Format\|Range\|Note
	236	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	237	\|Y\|Y o\|0~~303237\|
	238	\|M\|M d\|0~~99999\|
	239	\|B\|B h\|0~~7FFF\|
	240	\|F\|F d\|0~~32767\|
	241	\|SB\|SB h\|0~~7FFF\|
	242	\|TS\|TS d\|0~~1023\|
	243	\|TC\|TC d\|0~~1023\|
	244	\|STS\|STS d\|0~~1023\|
	245	\|STC\|STS d\|0~~1023\|
	246	\|CS\|CS d\|0~~1023\|
	247	\|CC\|CC d\|0~~1023\|
	248	\|SM\|SM d\|0~~9999\|
	249	\|L\|L d\|0~~32767\|
	250	\|S\|S d\|0~~4095\|
	251	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	252	\|TN\|TN d\|0~~1023\|
	253	\|STN\|STN d\|0~~1023\|
	254	\|CN\|CN d\|0~~1023\|
	255	\|R\|R d\|0~~32767\|
	256	\|SW\|SW h\|0~~7FFF\|
	257	\|Z\|Z d\|0~~23\|
	258	\|D\|D d\|0~~7999\|
	259	\|SD\|SD d\|0~~11999\|
2.1	260
79.1	261	PLC Settings
2.1	262
	263	Create a blank FX5U project
	264
79.1	265	Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
2.1	266
79.1	267	(% style="text-align:center" %)
	268	[[image:GX3.png]]
2.1	269
	270
79.1	271	(% style="text-align:center" %)
	272	[[image:FX5U 串口选型号.png]]
2.1	273
79.1	274	PLC Default Parameters:
	275	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.
2.1	276
79.1	277	(% style="text-align:center" %)
	278	[[image:FX5U plc串口参数配置.png]]
2.1	279
	280
79.1	281	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]
2.1	282
79.1	283	{{info}}
	284	✎Note: The serial port parameters should be set depending on field requirements.
	285	{{/info}}
2.1	286
79.1	287	(% style="text-align:center" %)
	288	[[image:FX5U plc串口参数.png]]
2.1	289
46.1	290	Cable Wiring
2.1	291
46.1	292	RS422
2.1	293
80.1	294	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d022c5ff4cf8c68e.png\|\|alt="image-20220825105105-2.png" height="288" width="711"]]
2.1	295
80.1	296	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_50e173394c73f154.png\|\|alt="image-20220825105533-3.png" height="246" width="420"]]
2.1	297
33.1	298	== FX5U Ethernet ==
2.1	299
	300	Mitsubishi FX5U series PLC
	301
59.1	302	V-BOX Settings
2.1	303
	304	\|Items\|Settings\|Note
	305	\|Protocol\|Mitsubishi FX5U\|
	306	\|Connection\|Ethernet\|
	307	\|Port No.\|5002\|Must be the same as the PLC setting
	308	\|PLC station No.\|0\|
	309
59.1	310	(% style="text-align:center" %)
	311	[[image:三菱 FX5U 以太网协议配置.png]]
2.1	312
59.1	313	Address List
	314
71.1	315	\|Type\|Device registers\|Format\|Range\|Note
	316	\|(% rowspan="15" %)Bit\|X\|X o\|0~~303237\|
	317	\|Y\|Y o\|0~~303237\|
	318	\|M\|M d\|0~~99999\|
	319	\|B\|B h\|0~~7FFF\|
	320	\|F\|F d\|0~~32767\|
	321	\|SB\|SB h\|0~~7FFF\|
	322	\|TS\|TS d\|0~~1023\|
	323	\|TC\|TC d\|0~~1023\|
	324	\|STS\|STS d\|0~~1023\|
	325	\|STC\|STS d\|0~~1023\|
	326	\|CS\|CS d\|0~~1023\|
	327	\|CC\|CC d\|0~~1023\|
	328	\|SM\|SM d\|0~~9999\|
	329	\|L\|L d\|0~~32767\|
	330	\|S\|S d\|0~~4095\|
	331	\|(% rowspan="9" %)Word\|W\|W h\|0~~3FF\|
	332	\|TN\|TN d\|0~~1023\|
	333	\|STN\|STN d\|0~~1023\|
	334	\|CN\|CN d\|0~~1023\|
	335	\|R\|R d\|0~~32767\|
	336	\|SW\|SW h\|0~~7FFF\|
	337	\|Z\|Z d\|0~~23\|
	338	\|D\|D d\|0~~7999\|
	339	\|SD\|SD d\|0~~11999\|
2.1	340
81.1	341	PLC Settings
2.1	342
81.1	343	Open GX Works3, create a new PLC project or open the project that has been created.
	344
	345	Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].
	346
75.2	347	(% style="text-align:center" %)
81.1	348	[[image:GX3.png]]
2.1	349
81.1	350	(% style="text-align:center" %)
	351	[[image:FX5U 串口选型号.png]]
	352
	353	PLC Default Parameters:
	354	[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.
	355
	356	(% style="text-align:center" %)
	357	[[image:FX5U 以太网配置.png]]
	358
75.2	359	[External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]
2.1	360
75.2	361	(% style="text-align:center" %)
	362	[[image:1.3.2.png]]
2.1	363
81.1	364	PC and PLC connection
	365
	366	[Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.
	367
	368	(% style="text-align:center" %)
	369	[[image:FX5U 以太网连接PLC.png]]
	370
	371	Downloading PLC project
	372	[Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]
	373
	374	(% style="text-align:center" %)
	375	[[image:FX5U以太网下载.png]]
	376
59.1	377	Cable Wiring
2.1	378
33.1	379	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	380
47.1	381	== L02 Serial ==
2.1	382
	383	Mitsubishi L02 series CPU built-in serial port.
	384
47.1	385	V-BOX Settings
2.1	386
	387	\|Item\|Settings\|Note
	388	\|Protocol\|Mitsubishi L02\|
	389	\|Connection\|RS422\|
	390	\|Baud rate\|115200\|
	391	\|Data bit\|8\|
	392	\|Parity\|Odd\|
	393	\|Stop bit\|1\|
	394	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	395
53.1	396	(% style="text-align:center" %)
	397	[[image:三菱 L02串口协议配置.png]]
	398
47.1	399	Address List
2.1	400
72.1	401	\|Type\|Device registers\|Format\|Range\|Note
47.1	402	\|(% colspan="1" rowspan="20" %)Bit
72.1	403	\|X\|X h\|0~~FFFF\|
	404	\|Y\|Y h\|0~~FFFF\|
	405	\|M\|M d\|0~~9999\|
	406	\|L\|L d\|0~~9999\|
	407	\|F\|F d\|0~~9999\|
	408	\|B\|B h\|0~~FFFF\|
	409	\|V\|V d\|0~~2047\|
	410	\|TC\|TC d\|0~~9999\|
	411	\|SS\|SS d\|0~~9999\|
	412	\|SC\|SC d\|0~~9999\|
	413	\|CS\|CS d\|0~~9999\|
	414	\|CC\|CC d\|0~~9999\|
	415	\|SB\|SB h\|0~~FFFF\|
	416	\|SM\|SM d\|0~~2047\|
	417	\|STS\|STS d\|0~~1023\|
	418	\|S\|S d\|0~~9999\|
	419	\|DX\|DX h\|0~~FFFF\|
	420	\|DY\|DY h\|0~~FFFF\|
	421	\|TS\|TS d\|0~~9999\|
	422	\|Dbit\|Dbit d.d\|0~~99999.0~~15\|
47.1	423	\|(% colspan="1" rowspan="9" %)Word
72.1	424	\|W\|W h\|0~~FFFF\|
	425	\|TN\|TN d\|0~~99999\|
	426	\|SN\|SN d\|0~~99999\|
	427	\|CN\|CN d\|0~~99999\|
	428	\|R\|R d\|0~~99999\|
	429	\|SW\|SW h\|0~~FFFF\|
	430	\|Z\|Z d\|0~~99999\|
	431	\|ZR\|ZR h\|0~~FFFF\|
	432	\|D\|D d\|0~~99999\|
2.1	433
47.1	434	Cable Wiring
2.1	435
47.1	436	RS422
2.1	437
47.1	438	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_90e38f152d639809.png\|\|alt="image-20220825161612-8.png" height="278" width="612"]]
2.1	439
47.1	440	[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d301e675d8224725.png\|\|alt="image-20220825160820-4.png" height="208" width="359"]]
2.1	441
48.1	442	== L02 Ethernet ==
2.1	443
	444	Mitsubishi L series CPU built-in Ethernet port.
	445
48.1	446	V-BOX Settings
2.1	447
	448	\|Items\|Settings\|Note
	449	\|Protocol\|MIT L02 CPU MELSEC\|
	450	\|Connection\|Ethernet\|
	451	\|Port No.\|1025\|Must be the same as the PLC setting
	452	\|PLC station No.\|0\|Must be the same as the PLC setting
	453
52.1	454	(% style="text-align:center" %)
	455	[[image:三菱 L02以太网协议配置1.png]]
51.1	456
48.1	457	PLC Settings (GX Works2 )
2.1	458
	459	Create a project
	460
	461	Set PLC IP, subnet mask and gateway;
	462
	463	Select [Binary Code] as communication data code;
	464
49.1	465	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_776e17505f3fc6c0.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_776e17505f3fc6c0.png" height="524" width="600"]]
2.1	466
	467	Set PLC port number, for example 1025
	468
49.1	469	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8d0d1a22d388f70b.png?width=600&height=524&rev=1.1\|\|alt="12.PLC Protocol_html_8d0d1a22d388f70b.png" height="524" width="600"]]
2.1	470
	471	Save settings;
	472
	473	Download project into PLC device;
	474
	475	Restart PLC device;
	476
49.1	477	Cable Wiring
2.1	478
49.1	479	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
2.1	480
	481	== {{id name="HQ12HSerial"/}}Q12H Serial ==
	482
	483	This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol
	484
	485	[[Download link>>url:https://ftp.we-con.com.cn/Download/WIKI/PI%20HMI/Demo/Communication/V-Box%20connect%20PLC%20Q12H.rar]]
	486
32.1	487	== QJ71E71 Ethernet ==
2.1	488
	489	Mitsubishi QJ71E71 Ethernet communication module;
	490
50.1	491	V-BOX Settings
2.1	492
	493	\|Items\|Settings\|Note
	494	\|Protocol\|MIT QJ71E71 MELSEC\|
	495	\|Connection\|Ethernet\|
	496	\|Port No.\|1025\|Must be the same as the PLC setting
	497	\|PLC station No.\|0\|Must be the same as the PLC setting
	498
61.1	499	(% style="text-align:center" %)
	500	[[image:三菱 QJ71 以太网协议配置.png]]
2.1	501
50.1	502	Address List
	503
74.1	504	\|Type\|Device registers\|Format\|Range\|Note
	505	\|(% rowspan="18" %)Bit\|X\|X h\|0~~1FFF\|
	506	\|Y\|Y h\|0~~1FFF\|
	507	\|M\|M d\|0~~99999\|
	508	\|L\|L d\|0~~8191\|
	509	\|F\|F d\|0~~2047\|
	510	\|B\|B h\|0~~1FFF\|
	511	\|V\|V d\|0~~2047\|
	512	\|TS\|TS d\|0~~2047\|
	513	\|TC\|TC d\|0~~2047\|
	514	\|SS\|SS d\|0~~2047\|
	515	\|SC\|SC d\|0~~2047\|
	516	\|CS\|CS d\|0~~1023\|
	517	\|CC\|CC d\|0~~1023\|
	518	\|SB\|SB h\|0~~7FF\|
	519	\|S\|S d\|0~~8191\|
	520	\|DX\|DX h\|0~~1FFF\|
	521	\|DY\|DY h\|0~~1FFF\|
	522	\|SM\|SM d\|8000~~9999\|
	523	\|(% rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
	524	\|D\|D d\|0~~12287\|
	525	\|W\|W h\|0~~1FFF\|
	526	\|TN\|TN d\|0~~2047\|
	527	\|SN\|SN d\|0~~2047\|
	528	\|CN\|CN d\|0~~1023\|
	529	\|R\|R d\|0~~32767\|
	530	\|SW\|SW h\|0~~7FF\|
	531	\|Z\|Z d\|0~~15\|
	532	\|ZR\|ZR h\|0~~FE7FF\|
2.1	533
50.1	534	PLC Settings(GX Works2)
2.1	535
	536	* Click [Ethernet/CC IE/MELSECNET];
	537	* Please select [Ethernet] as network type;
	538	* Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
	539	* Select [Online] as Mode;
50.1	540	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_d54f23688c520f78.png\|\|alt="image-20221119171343-2.png" height="341" width="587"]]
2.1	541	* Click [Operation setting] to set IP;
	542	* Select [Binary Code] as [Communication Data Code];
50.1	543	* [[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_ce8e6a671b9508e0.png\|\|alt="image-20221119171436-3.png" height="354" width="588"]]
2.1	544	* Click [Open setting]
	545	* Set protocol: TCP;
	546	* Set [unpassive] in [Open system];
	547	* Set [receive] in [Fixed buffer];
	548	* Set [procedure Exist] in [Fixed buffer communication];
	549	* Disable [Pairing open];
	550	* Set [No confirm] in [Existence confirmation];
	551	* Host station port number: 5009;
	552	* Save settings;
	553	* {{id name="Iimage-20221119171611-4.png"/}}[[image:xwiki_V-BOX_V-Net_Training_1+Communication_WebHome_1d8e2f4fb7c72471.png\|\|alt="image-20221119171611-4.png" height="354" width="588"]]
	554	* Download project into PLC and restart it
	555
50.1	556	Cable Wiring
2.1	557
34.1	558	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
83.2	559
	560	== Q03UDV ==
83.3	561
	562	Mitsubishi Q03UDV
	563
	564	V-BOX Settings
	565
83.4	566	\|Items\|Settings\|Note
83.7	567	\|Protocol\|MIT L02 CPU MELSEC PROTOCOL\|
83.4	568	\|Connection\|Ethernet\|
83.5	569	\|Port No.\|1025\|Must be the same as the PLC setting
83.6	570	\|PLC station No.\|0\|Must be the same as the PLC setting
83.7	571
83.8	572	[[image:1709779590561-640.png]]
	573
	574	Address List
	575
	576	\|Type\|Device registers\|Format\|Range\|Note
	577	\|(% colspan="1" rowspan="18" %)Bit\|X\|X h\|0~~1fff\|
	578	\|Y\|Y h\|0~~1fff\|
	579	\|SM\|SM d\|0~~2047\|
	580	\|M\|M d\|0~~99999\|
	581	\|L\|L d\|0~~8191\|
	582	\|F\|F d\|0~~2047\|
	583	\|V\|V d\|0~~2047\|
	584	\|B\|B h\|0~~1fff\|
	585	\|TS\|TS d\|0~~2047\|
	586	\|TC\|TC d\|0~~2047\|
	587	\|SS\|SS d\|0~~2047\|
	588	\|SC\|SC d\|0~~2047\|
	589	\|CS\|CS d\|0~~1023\|
	590	\|CC\|CC d\|0~~1023\|
	591	\|SB\|SB h\|0~~7ff\|
	592	\|S\|S d\|0~~8191\|
	593	\|DX\|DX h\|0~~1fff\|
	594	\|DY\|DY h\|0~~1fff\|
83.9	595	\|(% colspan="1" rowspan="10" %)Word\|SD\|SD d\|0~~2047\|
83.8	596	\|D\|D d\|0~~12287\|
	597	\|W\|W h\|0~~1fff\|
	598	\|TN\|TN d\|0~~2047\|
	599	\|SN\|SN d\|0~~2047\|
	600	\|CN\|CN d\|0~~1023\|
	601	\|SW\|SW h\|0~~7ff\|
	602	\|Z\|Z d\|0~~15\|
	603	\|R\|R d\|0~~32767\|
	604	\|ZR\|ZR h\|0~~fe7ff\|
83.10	605
83.12	606	(% class="wikigeneratedid" id="HPLCSettings" %)
	607	PLC Settings(GX Works2)
	608
	609	(% class="wikigeneratedid" %)
	610	PC and PLC connection:
	611
83.15	612	* Online→Read from PLC
83.12	613
	614	(% style="text-align:center" %)
	615	[[image:1.png]]
	616
83.15	617	* choose PLC Series→OK
83.14	618
83.12	619	(% style="text-align:center" %)
	620	[[image:StqCG53paq.png]]
	621
83.15	622	* serial USB→OK
83.14	623
83.12	624	(% style="text-align:center" %)
	625	[[image:Y7H80eq2Eb.png]]
	626
83.15	627	* Choose Parameter、Global Device Comment and Device Memory→Execute
83.14	628
83.12	629	(% style="text-align:center" %)
	630	[[image:6PAsdFz58I.png]]
	631
83.15	632	* OK→wait loading successfully→Close
83.14	633
83.13	634	(% style="text-align:center" %)
	635	[[image:0GBGUNn4hQ.png]]
	636
83.15	637	* Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on V-box)→End
83.14	638
83.13	639	(% style="text-align:center" %)
	640	[[image:Ypyl4SUHcf.png]]
	641
83.15	642	* Debug→Start/ Stop Simulation→wait loading successfully→Close
83.14	643
83.13	644	(% style="text-align:center" %)
	645	[[image:ZmUzFbS39y.png]]
	646
	647	(% style="text-align:center" %)
	648	[[image:ehoO3C6bry.png]]
	649
83.15	650	(% id="cke_bm_1296534S" style="display:none" %) (%%)Cable Wiring
	651
	652	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.可编程逻辑控制器Protocol_html_2297240b57346b2a.png" height="170" width="401"]]

Wiki source code of Mitsubishi

Navigation

Table of Contents