Mitsubishi

FX3U,3G,3GA Serial 

Supported Series: Mitsubishi FX3U, FX3G, FX3GA series

V-BOX Settings

Address List

PLC Setting

Open GX Works2, create a new PLC project or open the project that has been created.
Create new project： [Project]→[New]→[Series] FXCPU→[Type] FX3G/FX3GC→[OK].

PLC Default Parameters:
[Connection type]RS422;[Baud rate]9600, [Data bit]7, [Stop bit]1,[Parity]EVEN; [Station number]0
Note:The serial port parameters should be set depending on field requirements

PC and PLC connection:

[All connection]→[Connection 1]→[Transfer Setup Connection1]→[Serial USB]→RS-232C: PC and PLC are connected by USB to RS232 adapter,choose corresponding [COM Port]COM 5 →[Transmission speed]9.6Kbps→[setup] →[Parity]EVEN→[Data bits]7→[Stop bits]1→[OK]

Connection test:when connection is OK,the GX Works2 prompts “Successfully connected with the FX3G/FX3GCCPU.”

[PLC]→[Write to PLC]→[Online operation]→[Param+program]→[Execute]→[OK]

Cable Wiring

RS422

FX NOPROTOCOL

Mitsubishi FX3G-RS232-BD

V-Box Settings

Address List

Cable Wiring

FX3U Ethernet 

Supported Modules: FX3U-ENET-ADP, FX3U-ENET-L

V-BOX Settings

Address List

Ethernet Module Settings

FX3U-ENET-L module configuration
 Set up the FX3U-ENET-L Ethernet module settings as follows.
 Select the module location, which in this document is Module 0.

Select "Operational setting" to enter the following screen.

The Ethernet module IP is set to 192.168.39.254 in this document, and other options are default.

Select "Open setting" to enter the setting interface, the settings are as follows.

The third item "Protocol" selects TCP, and "Open system" selects MELSOFT connection, which allows the

Mitsubishi programming software GX works2 to communicate with the FX3U via the Ethernet module.

Click on "transter setup" - "PC side I/F setting", see the following figure.

After setting, the first download must use the programming cable, as shown in the figure; after that, can

use the IP set in the "Ethernet board" to communicate directly with the network cable.

PLC Settings (GX Works 2)

Create a blank FX5U project

Find Current Connection in the navigation

Select Connection Channel List

Select Ethernet board communication

Select Ethernet Module
 Set the IP address of the PLC

Read or write PLC data, in this document is read

FX5U Serial 

Mitsubishi FX5U series PLC

V-BOX Settings

Address List

PLC Settings 

Create a blank FX5U project

Open GX Works3, create a new PLC project or open the project that has been created. Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].

PLC Default Parameters: 
[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]:[Basic Settings] →[ Communication Protocol Type] MC Protocol→[Advanced Settings]:[Baud rate]9600Kbps, [Data Length]7, [Stop bit]1,[Parity]Odd.

[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[485 Serial Port]: [fixed Setting] →[Station No.]0→[Message Pattern] Pattern 1 (X,Y OCT)→[Apply]

Cable Wiring

RS422

FX5U Ethernet 

Mitsubishi FX5U series PLC

V-BOX Settings

Address List

PLC Settings 

Open GX Works3, create a new PLC project or open the project that has been created.

Create new project： [Project]→[New]→[Series] FX5CPU→[Type] FX5U→[OK].

PLC Default Parameters: 
[Navigation]→[Parameter]→[FX5UCPU]→[Module Parameter]→[Ethernet Port]:[Basic Settings] →[Own node settings]:[IP Address]192.168.40.11, [Subnet Mask]255.255.255.0, [Default Gateway]192.168.40.1,[ Communication Data Code] Binary.

[External Device Configuration]→[Detailed Settings]→[Ethernet Configuration(Built-in Ethernet Port)]→[Ethernet Device (General)]→[SLMP Connection Module] Drag under Host for Connection No.1→[Port No.]5002→[Close with Reflecting the Setting]

PC and PLC connection

[Online]→[Current Connection Destination]→[Direct Coupled Setting]→[Ethernet]→[Adapter] Realtek PCIe GBE Family Controller→[Communication Test]: Successfully connected with the FX5UCPU.

Downloading PLC project
[Online]→[Write to PLC]→[Online Data operation]→[Param+program]→[Execute]→[Yes] →[Yes to all]

Cable Wiring

L02 Serial 

Mitsubishi L02 series CPU built-in serial port.

V-BOX Settings

Address List

Cable Wiring

RS422

L02 Ethernet 

Mitsubishi L series CPU built-in Ethernet port.

V-BOX Settings

PLC Settings (GX Works2 )

Create a project

Set PLC IP, subnet mask and gateway;

Select [Binary Code] as communication data code;

Set PLC port number, for example 1025

Save settings;

Download project into PLC device;

Restart PLC device;

Cable Wiring

Q12H Serial 

This Demo shows V-BOX communicate with Q12H PLC by Q02H serial Protocol

Download link

QJ71E71 Ethernet 

Mitsubishi QJ71E71 Ethernet communication module;

V-BOX Settings

Address List

PLC Settings(GX Works2)

• Click [Ethernet/CC IE/MELSECNET];
• Please select [Ethernet] as network type;
• Set station I/O number according to situation (For example, 0020 means that the module is connected to PLC CPU in first order);
• Select [Online] as Mode;
• 
• Click [Operation setting] to set IP;
• Select [Binary Code] as [Communication Data Code];
• 
• Click [Open setting]
• Set protocol: TCP;
• Set [unpassive] in [Open system];
• Set [receive] in [Fixed buffer];
• Set [procedure Exist] in [Fixed buffer communication];
• Disable [Pairing open];
• Set [No confirm] in [Existence confirmation];
• Host station port number: 5009;
• Save settings;
• 
• Download project into PLC and restart it

Cable Wiring

Q03UDV

Mitsubishi Q03UDV

V-BOX Settings

Address List

PLC Settings(GX Works2)

PC and PLC connection:

• Online→Read from PLC

• choose PLC Series→OK 

• serial USB→OK

• Choose Parameter、Global Device Comment and Device Memory→Execute 

• OK→wait loading successfully→Close

•  Navigation→Parameter→PLC Parameter→IP Address Setting→Built-in Ethernet Port Setting→Host Station(Same as the port on  V-box)→End

• Debug→Start/ Stop Simulation→wait loading successfully→Close

 Cable Wiring