Wiki source code of 1 Communication

Version 112.1 by Ben on 2022/08/25 13:36

version	line-number	content
52.1	1	= (% style="color:inherit; font-family:inherit" %)WECON PLC(%%) =
1.1	2
63.1	3	== LX3V Serial Protocol ==
31.1	4
20.1	5	Supported series: WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM
1.1	6
81.1	7	1）PLC Settings
1.1	8
20.1	9	\|Item\|Settings\|Note
	10	\|Protocol\|WECON LX2V/ LX2E/ LX3V/LX3VP/LX3VE/LX3VM\|
	11	\|Connection\|RS422/RS485\|
	12	\|Baud rate\|9600\|
	13	\|Data bit\|7\|
	14	\|Parity\|EVEN\|
	15	\|Stop bit\|1\|
	16	\|PLC station No.\|1\|
1.1	17
82.1	18	2）PLC Address List
20.1	19
	20	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	21	\|(% rowspan="6" %)Bit\|X\|X\|Xo\|0~~303237\|
	22	\|Y\|Y\|Y o\|0~~303237\|
	23	\|M\|M\|M d\|0~~99999\|
	24	\|T\|T\|T d\|0~~99999\|
	25	\|C\|C\|C d\|0~~99999\|
	26	\|S\|S\|S d\|0~~99999\|
	27	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	28	\|Y\|Y\|Y o\|0~~303237\|
	29	\|M\|M\|M d\|0~~99999\|
	30	\|T\|T\|T d\|0~~99999\|
	31	\|C\|C\|C d\|0~~199\|
	32	\|D\|D\|D d\|0~~7999\|
	33	\|S\|S\|S d\|0~~99999\|
	34	\|SD\|SD\|SD d\|8000~~9999\|
	35
83.1	36	3）Configure the communication protocol
20.1	37
80.1	38	[[image:image-20220824152217-1.png]]
	39
83.1	40	4）hardware connection
80.1	41
20.1	42	* RS422
	43
69.1	44	[[image:image-20220824120614-5.png]]
20.1	45
68.1	46	* RS485
	47
69.1	48	[[image:image-20220824120524-3.png]]
68.1	49
63.1	50	== LX5V Serial Protocol ==
28.1	51
84.1	52	This example introduces the establishment of serial port communication between V-BOX and LX5V. It is introduced through three parts: PLC software configuration, V-BOX software configuration, and hardware wiring.
20.1	53
	54	Software configuration of PLC
	55
	56	1）PLC programming software
	57
71.1	58	[[image:image-20220824142722-1.png]]
20.1	59
	60	2）New PLC project
	61
	62	Click New Project and select the PLC model.
	63
33.1	64	[[image:image-20220822172623-2.png]]
20.1	65
	66	3）Set Serial port parameters
	67
	68	Follow the steps below to configure Serial port parameters
	69
	70	Baud rate：115200
	71
	72	Data bit：8
	73
	74	Stop bit：1
	75
	76	Parity：No verification
	77
33.1	78	[[image:image-20220822172657-3.png]]
20.1	79
	80	4）Registers list
	81
33.1	82	[[image:image-20220822172730-4.png]]
20.1	83
33.1	84	V-BOX software configuration
28.1	85
35.1	86	1）V-BOX programming software
20.1	87
35.1	88	[[image:image-20220824104124-1.png]]
20.1	89
35.1	90	2）V-NET add device
20.1	91
35.1	92	Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
20.1	93
35.1	94	[[image:image-20220824104909-2.png]]
20.1	95
	96	3）Set communication port parameters
	97
	98	Click the communication configuration button on the left to find the communication protocol with LX5V. After selecting the protocol, configure the communication parameters of the COM port.
	99
	100	Baud rate：115200
	101
	102	Data bit：8
	103
	104	Stop bit：1
	105
	106	Parity：No verification
	107
70.1	108	[[image:image-20220824142130-1.png]]
20.1	109
	110	hardware connection
	111
	112	1）Hardware wiring diagram
	113
70.1	114	[[image:image-20220824142546-2.png]]
28.1	115
70.1	116	[[image:image-20220824142643-3.png]]
28.1	117
74.1	118	The above are all the steps for establishing serial port communication between V-BOX with LX5V PLC.
20.1	119
63.1	120	== LX5V-N Ethernet protocol ==
20.1	121
77.1	122	This example introduces the establishment of Ethernet communication between V-BOX and LX5V-N. It is introduced through three parts: PLC software configuration, V-BOX software configuration, and hardware wiring.
20.1	123
	124	Software configuration of PLC
	125
	126	1）PLC programming software
	127
72.1	128	[[image:image-20220824142722-1.png]]
20.1	129
	130	2）New PLC project
	131
	132	Click New Project and select the PLC model.
	133
73.1	134	[[image:image-20220824143613-1.png]]
20.1	135
	136	3）Set Ethernet port parameters
	137
	138	Follow the steps below to configure Ethernet parameters
	139
	140	PLC IP address：192.168.39.200
	141
	142	default gateway：192.168.39.1
	143
	144	subnet mask：255.255.255.0
	145
73.1	146	[[image:image-20220824143744-2.png]]
20.1	147
	148	4）Registers list
	149
74.1	150	[[image:image-20220822172730-4.png]]
20.1	151
74.1	152	(% id="cke_bm_22473S" style="display:none" %) (%%)V-BOX software configuration
20.1	153
74.1	154	1）V-BOX programming software
20.1	155
74.1	156	[[image:image-20220824104124-1.png]]
20.1	157
74.1	158	2）V-NET add device
20.1	159
74.1	160	Open V-NET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the access key, password and remark, to add the device.
20.1	161
74.1	162	[[image:image-20220824104909-2.png]]
20.1	163
79.1	164	3）Set communication Protocol
20.1	165
74.1	166	Click Communication to configure the LX5V plc protocol and IP address.
20.1	167
74.1	168	[[image:image-20220824144619-1.png]]
20.1	169
	170	hardware connection
	171
	172	1）Hardware wiring diagram
	173
74.1	174	[[image:image-20220824151127-2.png]]
20.1	175
74.1	176	The above are all the steps for establishing ethernet communication between V-BOX with LX5V PLC.
20.1	177
23.1	178	= Rockwell PLC =
22.1	179
63.1	180	== (% id="cke_bm_5621S" style="display:none" %) (%%)MicroLogix Protocol ==
37.1	181
	182	MicroLogix 1000/1100/1200/1400/1500; SLC 5/03 5/04 5/05 PLC-5
	183
87.1	184	1）PLC Settings
37.1	185
	186	\|Item\|Settings\|Note
85.1	187	\|Protocol\|Allen-Bradlley DF1 Advanced\|
37.1	188	\|Connection\|RS232\|
	189	\|Baud rate\|19200\|
	190	\|Data bit\|8\|
	191	\|Parity\|None\|
	192	\|Stop bit\|1\|
	193	\|PLC station No.\|1\|
	194
87.1	195	2）Address List
37.1	196
	197	\|Type\|Device registers\|Format\|Range\|Note
	198	\|(% rowspan="5" %)Bit\|I\|I d.d\|0.0~~255.15\|
	199	\|O\|O d.d\|0.0~~255.15\|
	200	\|B\|B nnhh.dd\|0.0~~ffff.15\|nn: block number (hex)
	201	\|S\|S d.d\|0.0~~255.15\|
	202	\|N\|N nnhh.dd\|0.0~~ffff.15\|nn: block number (hex)
	203	\|(% rowspan="9" %)Word\|S\|S d\|0~~255\|
	204	\|TS\|TS nnhh\|0~~ffff\|(% rowspan="8" %)nn: block number (hex)
	205	\|TP\|TP nnhh\|0~~ffff
	206	\|CS\|CS nnhh\|0~~ffff
	207	\|CP\|CP nnhh\|0~~ffff
	208	\|N\|N nnhh\|0~~ffff
	209	\|C\|C nnhh\|0~~ffff
	210	\|T\|T nnhh\|0~~ffff
	211	\|R\|R nnhh\|0~~ffff
	212
86.1	213	3）Configure the communication protocol[[image:image-20220824152928-1.png]]
85.1	214
87.1	215	4）Configure the communication protocol
37.1	216
	217	[[image:image-20220824110724-1.png]]
	218
112.1	219	== Micro850_FreeTag ==
37.1	220
11.1	221	(((
16.1	222	(((
38.1	223	This example introduces the establishment of Ethernet communication between Wecon V-box and CompactLogix L1769. It is introduced through three parts: PLC software configuration, V-box software configuration, and hardware wiring.
16.1	224	)))
11.1	225	)))
	226
	227	(((
15.1	228	(% class="wikigeneratedid" id="HSoftwareconfigurationofPLC" %)
	229	(((
	230	Software configuration of PLC
11.1	231	)))
	232
15.1	233	(% class="wikigeneratedid" id="HPLCprogrammingsoftware" %)
11.1	234	(((
15.1	235	1）PLC programming software
	236	)))
11.1	237
17.1	238	[[image:image-20220714162600-1.png]]
11.1	239
15.1	240	(% class="wikigeneratedid" id="HNewPLCproject" %)
11.1	241	(((
15.1	242	2）New PLC project
11.1	243	)))
	244
	245	(((
16.1	246	(((
15.1	247	Click New Project and select the PLC model.
11.1	248	)))
16.1	249	)))
11.1	250
	251	(((
17.1	252	[[image:image-20220714162617-2.png]]
11.1	253	)))
	254
	255	(((
17.1	256
16.1	257
17.1	258	[[image:image-20220714162652-4.png]]
11.1	259	)))
	260
	261	(((
15.1	262	(% class="wikigeneratedid" id="HSetEthernetparameters" %)
	263	(((
	264	3）Set Ethernet parameters
	265	)))
11.1	266
	267	(((
15.1	268	(((
16.1	269	(((
11.1	270	Follow the steps below to configure Ethernet parameters
	271	)))
15.1	272	)))
16.1	273	)))
11.1	274
	275	(((
15.1	276	(((
16.1	277	(((
11.1	278	PLC IP address：192.168.40.101
	279	)))
15.1	280	)))
16.1	281	)))
11.1	282
	283	(((
15.1	284	(((
16.1	285	(((
11.1	286	default gateway：192.168.40.1
	287	)))
15.1	288	)))
16.1	289	)))
11.1	290
	291	(((
15.1	292	(((
16.1	293	(((
11.1	294	subnet mask：255.255.255.0
	295	)))
15.1	296	)))
16.1	297	)))
11.1	298
	299	(((
17.1	300	[[image:image-20220714162713-5.png]]
11.1	301	)))
	302
	303	(((
	304
	305	)))
	306
	307	(((
15.1	308	(% class="wikigeneratedid" id="HV-boxsoftwareconfiguration" %)
	309	(((
	310	V-box software configuration
	311	)))
11.1	312
15.1	313	(% class="wikigeneratedid" id="HV-boxprogrammingsoftware" %)
	314	(((
	315	1）V-box programming software
	316	)))
11.1	317
15.1	318	(% class="wikigeneratedid" %)
	319	(((
17.1	320	[[image:image-20220714162725-6.png]]
15.1	321	)))
11.1	322
15.1	323	(% class="wikigeneratedid" id="HConfiguredevicenetwork" %)
	324	(((
	325	2）Configure device network
	326	)))
11.1	327
	328	(((
15.1	329	(((
16.1	330	(((
11.1	331	Click the Configuration Download button[[image:image-20220714115308-8.png\|\|height="22" width="15"]], It is used to configure the device network, update the device time, obtain the device machine code, check the device network, etc.
	332	)))
16.1	333
	334	(((
	335	In the example below, the IP address of V-Box is configured as 192.168.40.66, and the networking method is 4G connection
15.1	336	)))
16.1	337	)))
	338	)))
11.1	339
	340	(((
15.1	341	(((
17.1	342	[[image:image-20220714162737-7.png]]
16.1	343
	344
11.1	345	)))
	346	)))
	347	)))
	348	)))
	349
15.1	350	(% class="wikigeneratedid" id="HV-netadddevice" %)
11.1	351	(((
15.1	352	3）V-net add device
11.1	353	)))
15.1	354	)))
11.1	355
	356	(((
16.1	357	(((
21.1	358	Open VNET client software → add device. As shown in the figure below, click "+" in the order of steps, and the Add Device window will pop up, enter the device machine code/product code, device password, and device alias to add the device. [[image:image-20220714162752-8.png]]
11.1	359	)))
	360
	361
	362	)))
	363
	364	(((
15.1	365	(% class="wikigeneratedid" id="HSetcommunicationportparameters" %)
	366	(((
	367	4）Set communication port parameters
	368	)))
11.1	369
16.1	370	(((
	371	In the device list on the left, find the Vbox that communicates with the L1769, click it and select configuration,communication port configuration in the main interface to add a communication protocol.
11.1	372	)))
	373
17.1	374	[[image:image-20220714162805-9.png]]
16.1	375	)))
	376
	377	(((
11.1	378	The communication port is selected as Ethernet, the device type is selected as Allen-Bradley, the protocol is Allen-BradleyMicro850_FreeTag EthemetIP, and the IP is the internal IP address of the L1769 PLC. The port number is 44818.
16.1	379	)))
11.1	380
97.1	381	[[image:image-20220824164346-1.png]]
11.1	382
	383
16.1	384	(((
22.1	385	After adding the protocol Allen-BradleyMicro850_FreeTag, click[[image:image-20220714143838-2.png]]icon add label.[[image:image-20220714162827-11.png]]
16.1	386	)))
14.1	387
16.1	388	(% class="wikigeneratedid" id="HEngineeringproduction" %)
	389	(((
	390	5）Engineering production
	391	)))
14.1	392
16.1	393	(% class="wikigeneratedid" %)
	394	(((
	395	(((
	396	According to your own needs, use the V-NET client software to edit the required data monitoring points.
	397	)))
14.1	398
17.1	399	[[image:image-20220714162841-12.png]]
14.1	400
16.1	401
	402	(((
	403	hardware connection
	404	)))
	405	)))
	406
	407	(((
	408	1）Hardware wiring diagram
	409	)))
	410
	411	(((
	412	(((
	413	This example introduces Wecon V-box with Allen-Bradley L1769 PLC to establish communication through Ethernet. The connection diagram is as follows:
	414	)))
	415
17.1	416	[[image:image-20220714162856-13.png]]
16.1	417
	418	(((
41.1	419	The above are all the steps for establishing Ethernet communication between Wecon V-box with CompactLogix L1769 PLC.
26.1	420
	421
	422	== Allen-Bradley Ethernet DF1 ==
	423
	424	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Allen-Bradley%20Ethernet%20DF1.zip]]
	425
	426
	427	= Siemens PLC =
61.1	428
63.1	429	== S7-200 Smart Ethernet Protocol ==
61.1	430
	431	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20S7-200%20Smart.zip]]
88.1	432
	433
99.1	434	== S7-300 Ethernet Protocol ==
88.1	435
	436	Supported Series: Siemens S7-300 series PLC
	437
90.1	438	1）PLC Setting
88.1	439
	440	\|Items\|Settings\|Note
	441	\|Protocol\|Simens S7-300 Ethernet\|
	442	\|Connection\|Ethernet\|
	443	\|Port No.\|102\|
	444	\|PLC station No.\|2\|Need to be same as the PLC setting
	445
90.1	446	2）Address List
88.1	447
	448	\|Type\|Device register\|HMI register\|Format\|Range\|Note
	449	\|(% rowspan="4" %)Bit\|I\|I\|I ddddd.o\|0.0~~99999.7\|
	450	\|Q\|Q\|Q ddddd.o\|0.0~~99999.7\|
	451	\|M\|M\|M ddddd.o\|0.0~~99999.7\|
	452	\|DB0.DB~~DB99.DB\|DBxDBD\|DBxDB nndddd.o\|0.0~~99999999.7\|(((
	453	nn: block number;
	454
	455	dddd: address;
16.1	456	)))
88.1	457	\|(% rowspan="8" %)Word\|I\|IW\|IW ddddd\|0~~99999\|
	458	\|Q\|QW\|QW ddddd\|0~~99999\|
	459	\|(% rowspan="3" %)M\|MB\|MB ddddd\|0~~99999\|
	460	\|MW\|MW ddddd\|0~~99999\|(((
	461	MW0=MB(0~~1)
	462
	463	MW2=MB(2~~3)
	464
	465	Address value is a multiple of 2
16.1	466	)))
88.1	467	\|MD\|MD ddddd\|0~~99999\|(((
	468	MD0=MB(0~~3)
16.1	469
88.1	470	MD4=MB(4~~7)
	471
	472	Address value is a multiple of 4
	473	)))
	474	\|(% rowspan="3" %)DB0.DB~~DB99.DB\|DBxDBB\|DBxDBB nndddd\|0~~99999999\|(% rowspan="3" %)(((
	475	nn: block number;
	476
	477	dddd: address
	478	)))
	479	\|DBxDBW\|DBxDBW nndddd\|0~~99999999
	480	\|DBxDBD\|DBxDBD nndddd\|0~~99999999
	481
90.1	482	3）Configure the communication protocol
88.1	483
90.1	484	[[image:image-20220824161345-1.png]]
88.1	485
96.1	486	4）Cable Wiring
88.1	487
90.1	488	[[image:image-20220824161450-2.png]]
88.1	489	)))
	490	)))
	491
63.1	492	== S7-1200 Ethernet Protocol ==
1.1	493
	494	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20S7-1200%20via%20Ehernet.zip]]
	495
93.1	496	== S7-XXX Ethernet Protocol ==
91.1	497
	498	Supported Series: Siemens S7-400, S7-1200 and S7-1500
	499
95.1	500	1）PLC Setting
91.1	501
	502	\|=Items\|=Settings\|=Note
	503	\|Protocol\|Siemens S7-XXX\|
	504	\|Connection\|Ethernet\|
	505	\|Port No.\|102\|
	506	\|Device No.\|Slot (Default 1 for S7-1500/ 2 for S7-1200/ 3 for S7-400)\|
	507	\|HMI No.\|Rack (Default as 0)\|
	508
94.1	509	Slot from TIA Portal is equal to Device No. of V-net
91.1	510
94.1	511	Rack from TIA Portal is equal to HMI No. of V-net
91.1	512
92.1	513	[[image:image-20220824162459-3.png]]
91.1	514
94.1	515	[[image:image-20220824163305-2.png]]
	516
95.1	517	2）Address List
91.1	518
	519	\|Type\|Device register\|HMI register\|Format\|Range\|Note
	520	\|(% rowspan="4" %)Bit\|I\|I\|M d.o\|(((
	521	d:0~-~-9999
	522
	523	o:0-7
	524	)))\|
	525	\|Q\|Q\|Q d.o\|(((
	526	d:0~-~-9999
	527
	528	o:0-7
	529	)))\|
	530	\|M\|M\|M d.o\|(((
	531	d:0~-~-9999
	532
	533	o:0-7
	534	)))\|
	535	\|DB0.DB-DB99.DB\|DBxDB\|DBxDBnndddd.o\|(((
	536	nn:0-9999,
	537
	538	dddd:0-9999,
	539
	540	o:0-7
	541	)))\|(((
	542	nn:DB No.
	543
	544	dddd:address value
	545
	546	o: digit address
	547	)))
	548	\|(% rowspan="8" %)Word\|M\|MB\|MB d\|d:0-99999\|
	549	\|M\|MW\|MW d\|d:0-99999\|(((
	550	MW0=MB(0~~1)
	551
	552	MW2=MB(2~~3)
	553
	554	Address value is a multiple of 2
	555	)))
	556	\|M\|MD\|MD d\|d:0-99999\|(((
	557	MD0=MB(0~~3)
	558
	559	MD4=MB(4~~7)
	560
	561	Address value is a multiple of 4
	562	)))
	563	\|I\|IW\|IW d\|d:0-99999\|
	564	\|Q\|QW\|QW d\|d:0-99999\|
	565	\|DB0.DB-DB99.DB\|DBxDBB\|DBxDBBnndddd\|(((
	566	nn:0-9999
	567
	568	dddd:0-9999
	569	)))\|(((
	570	nn:DB No.
	571
	572	dddd:address value
	573	)))
	574	\|DB0.DB-DB99.DB\|DBxDBW\|DBxDBWnndddd\|(((
	575	nn:0-9999
	576
	577	dddd:0-9999
	578	)))\|(((
	579	nn:DB No.
	580
	581	dddd:address value
	582
	583	Address value is a multiple of 2
	584	)))
	585	\|DB0.DB-DB99.DB\|DBxDBD\|DBxDBDnndddd\|(((
	586	nn:0-9999
	587
	588	dddd:0-9999
	589	)))\|(((
	590	nn:DB No.
	591
	592	dddd:address value
	593
	594	Address value is a multiple of 4
	595	)))
	596
95.1	597	3）Configure the communication protocol
91.1	598
94.1	599	[[image:image-20220824163448-3.png]]
91.1	600
	601	✎Note:
	602
94.1	603	* The S7-1200 supports simultaneous connection of three devices, so the driver supports simultaneous access to PLC by three V-BOX.
	604	* V-BOX access PLC, use S7 protocol, access PLC TSAP 02.01 (s7-1200 PROFINET interface only supports three connections, the default support), detailed reference to the system manual of S7-1200.
91.1	605
95.1	606	4）Cable Wiring
91.1	607
92.1	608	[[image:image-20220824162342-2.png]]
91.1	609
98.1	610
56.1	611	= Mitsubishi PLC =
	612
104.1	613	== FX1S，1N，2N Serial Protocol ==
103.1	614
105.1	615	Supported Series: Mitsubishi FX1S, FX1N, FX2N series
103.1	616
105.1	617	1）V-BOX Settings
103.1	618
105.1	619	\|Item\|Settings\|Note
	620	\|Protocol\|Mitsubishi FX1S/FX1N/FX2N\|
	621	\|Connection\|RS422/RS485/RS232\|
	622	\|Baud rate\|9600~~115200\|
	623	\|Data bit\|7/8\|
	624	\|Parity\|EVEN/Odd/None\|
	625	\|Stop bit\|1/2\|
	626	\|PLC station No.\|1~~255\|
104.1	627
105.1	628	2）Address List
104.1	629
105.1	630	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	631	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	632	\|Y\|Y\|Y o\|0~~303237\|
	633	\|M\|M\|M d\|0~~99999\|
	634	\|T\|T\|T d\|0~~99999\|
	635	\|C\|C\|C d\|0~~99999\|
104.1	636	\|S\|S\|S d\|0~~99999\|
105.1	637	\|SM\|SM\|SM d\|8000~~9999\|
	638	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	639	\|Y\|Y\|Y o\|0~~303237\|
	640	\|M\|M\|M d\|0~~99999\|
	641	\|T\|T\|T d\|0~~99999\|
	642	\|C\|C\|C d\|0~~199\|
	643	\|D\|D\|D d\|0~~7999\|
104.1	644	\|S\|S\|S d\|0~~99999\|
105.1	645	\|SD\|SD\|SD d\|8000~~9999\|
104.1	646
106.1	647	3）Configure the communication protocol
104.1	648
107.1	649	[[image:image-20220825102844-3.png]]
106.1	650
	651	4）Cable Wiring
	652
104.1	653	* RS422
	654
107.1	655	[[image:image-20220825103350-4.png]]
104.1	656
	657	[[image:image-20220825100845-4.png]]
	658
	659
106.1	660	== FX3U，3G，3GA Serial Protocol ==
56.1	661
106.1	662	Supported Series: Mitsubishi FX3U, FX3G, FX3GA series
56.1	663
106.1	664	1）V-BOX Settings
	665
	666	\|Item\|Settings\|Note
	667	\|Protocol\|Mitsubishi FX3U/3G/3GA\|
	668	\|Connection\|RS422/RS485/RS232\|
	669	\|Baud rate\|9600~~115200\|
	670	\|Data bit\|7/8\|
	671	\|Parity\|EVEN/Odd/None\|
	672	\|Stop bit\|1/2\|
	673	\|PLC station No.\|1~~255\|
	674
	675	2）Address List
	676
	677	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	678	\|(% rowspan="7" %)Bit\|X\|X\|Xo\|0~~303237\|
	679	\|Y\|Y\|Y o\|0~~303237\|
	680	\|M\|M\|M d\|0~~99999\|
	681	\|T\|T\|T d\|0~~99999\|
	682	\|C\|C\|C d\|0~~99999\|
	683	\|S\|S\|S d\|0~~99999\|
	684	\|SM\|SM\|SM d\|8000~~9999\|
	685	\|(% rowspan="8" %)Word\|X\|X\|Xo\|0~~303237\|
	686	\|Y\|Y\|Y o\|0~~303237\|
	687	\|M\|M\|M d\|0~~99999\|
	688	\|T\|T\|T d\|0~~99999\|
	689	\|C\|C\|C d\|0~~199\|
	690	\|D\|D\|D d\|0~~7999\|
	691	\|S\|S\|S d\|0~~99999\|
	692	\|SD\|SD\|SD d\|8000~~9999\|
	693
	694	3）Configure the communication protocol
	695
107.1	696	[[image:image-20220825102649-2.png]]
106.1	697
	698	4）Cable Wiring
	699
	700	* RS422
	701
107.1	702	[[image:image-20220825103421-5.png]]
106.1	703
	704	[[image:image-20220825100845-4.png]]
	705
	706
103.1	707	== FX5U Serial Protocol ==
	708
107.1	709	Mitsubishi FX5U series PLC
103.1	710
108.1	711	1）V-BOX Settings
107.1	712
	713	\|Item\|Settings\|Note
	714	\|Protocol\|Mitsubishi FX5U\|
	715	\|Connection\|RS422/RS485\|
	716	\|Baud rate\|9600\|
	717	\|Data bit\|7\|
	718	\|Parity\|Odd\|
	719	\|Stop bit\|1\|
	720	\|PLC station No.\|1~~255\|Need to be the same as PLC settings
	721
108.1	722	2）Address List
107.1	723
	724	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	725	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	726	\|Y\|Y\|Y o\|0~~303237\|
	727	\|M\|M\|M d\|0~~99999\|
	728	\|B\|B\|B h\|0~~7FFF\|
	729	\|F\|F\|F d\|0~~32767\|
	730	\|SB\|SB\|SB h\|0~~7FFF\|
	731	\|TS\|TS\|TS d\|0~~1023\|
	732	\|TC\|TC\|TC d\|0~~1023\|
	733	\|STS\|STS\|STS d\|0~~1023\|
	734	\|STC\|STC\|STS d\|0~~1023\|
	735	\|CS\|CS\|CS d\|0~~1023\|
	736	\|CC\|CC\|CC d\|0~~1023\|
	737	\|SM\|SM\|SM d\|0~~9999\|
	738	\|L\|L\|L d\|0~~32767\|
	739	\|S\|S\|S d\|0~~4095\|
	740	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	741	\|TN\|TN\|TN d\|0~~1023\|
	742	\|STN\|STN\|STN d\|0~~1023\|
	743	\|CN\|CN\|CN d\|0~~1023\|
	744	\|R\|R\|R d\|0~~32767\|
	745	\|SW\|SW\|SW h\|0~~7FFF\|
	746	\|Z\|Z\|Z d\|0~~23\|
	747	\|D\|D\|D d\|0~~7999\|
	748	\|SD\|SD\|SD d\|0~~11999\|
	749
108.1	750	3）PLC Settings (GX Works 3)
107.1	751
	752	Create a blank FX5U project
	753
	754	Find the 485 serial port module in the system navigation bar and double click to enter the settings.
	755
	756	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5c9cb13fac1e6c93.png?width=200&height=462&rev=1.1\|\|alt="12.PLC Protocol_html_5c9cb13fac1e6c93.png" height="462" width="200"]]
	757
	758	Select protocol in the setting item, and set parameters.
	759
	760	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_de942589ca070228.png?width=600&height=324&rev=1.1\|\|alt="12.PLC Protocol_html_de942589ca070228.png" height="324" width="600"]]
	761
	762	Set station number, and [Message Pattern] (Pattern 1 or Pattern 4)
	763
	764	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_387ec7d00b5feb59.png?width=600&height=323&rev=1.1\|\|alt="12.PLC Protocol_html_387ec7d00b5feb59.png" height="323" width="600"]]
	765
	766	Click the [Apply] button to finish the setting.
	767
	768	Click download and select the items as below, then click [execute] to download the configuration to PLC.
	769
	770	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_cdef1c5ec8cc2105.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_cdef1c5ec8cc2105.png" height="434" width="600"]]
	771
	772	As soon as download is completed, connect PLC with serial port, then configure it in the [Specify Connection Destination Connection].
	773
	774	Done.
	775
108.1	776	4）Configure the communication protocol
107.1	777
108.1	778	[[image:image-20220825104904-1.png]]
107.1	779
108.1	780	5）Cable Wiring
107.1	781
	782
	783	* RS422
	784
108.1	785	[[image:image-20220825105105-2.png]]
107.1	786
108.1	787	[[image:image-20220825105533-3.png]]
107.1	788
100.1	789	== FX5U Ethernet Protocol ==
	790
	791	Mitsubishi FX5U series PLC
	792
110.1	793	1）V-BOX Settings
100.1	794
	795	\|Items\|Settings\|Note
	796	\|Protocol\|Mitsubishi FX5U\|
	797	\|Connection\|Ethernet\|
	798	\|Port No.\|5002\|Must be the same as the PLC setting
	799	\|PLC station No.\|0\|
	800
110.1	801	2）Address List
100.1	802
	803	\|Type\|Device registers\|HMI registers\|Format\|Range\|Note
	804	\|(% rowspan="15" %)Bit\|X\|X\|X o\|0~~303237\|
	805	\|Y\|Y\|Y o\|0~~303237\|
	806	\|M\|M\|M d\|0~~99999\|
	807	\|B\|B\|B h\|0~~7FFF\|
	808	\|F\|F\|F d\|0~~32767\|
	809	\|SB\|SB\|SB h\|0~~7FFF\|
	810	\|TS\|TS\|TS d\|0~~1023\|
	811	\|TC\|TC\|TC d\|0~~1023\|
	812	\|STS\|STS\|STS d\|0~~1023\|
	813	\|STC\|STC\|STS d\|0~~1023\|
	814	\|CS\|CS\|CS d\|0~~1023\|
	815	\|CC\|CC\|CC d\|0~~1023\|
	816	\|SM\|SM\|SM d\|0~~9999\|
	817	\|L\|L\|L d\|0~~32767\|
	818	\|S\|S\|S d\|0~~4095\|
	819	\|(% rowspan="9" %)Word\|W\|W\|W h\|0~~3FF\|
	820	\|TN\|TN\|TN d\|0~~1023\|
	821	\|STN\|STN\|STN d\|0~~1023\|
	822	\|CN\|CN\|CN d\|0~~1023\|
	823	\|R\|R\|R d\|0~~32767\|
	824	\|SW\|SW\|SW h\|0~~7FFF\|
	825	\|Z\|Z\|Z d\|0~~23\|
	826	\|D\|D\|D d\|0~~7999\|
	827	\|SD\|SD\|SD d\|0~~11999\|
	828
110.1	829	3）PLC Settings (GX Works 3)
100.1	830
	831	Find the [Ethernet port] in the navigation area.
	832
109.1	833	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_8e8f85ace087346c.png?width=300&height=593&rev=1.1\|\|alt="12.PLC Protocol_html_8e8f85ace087346c.png" height="593" width="300"]]
100.1	834
	835	Select [Own Node Settings] in the [Setting Item List];
	836
	837	Set [IP Address], [Subnet Mask], [Default Gateway];
	838
	839	Click [Detailed Settings] into [Ethernet Configuration (Built-in Ethernet Port)] windows;
	840
109.1	841	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_5d98495052c8c10e.png?width=600&height=339&rev=1.1\|\|alt="12.PLC Protocol_html_5d98495052c8c10e.png" height="339" width="600"]]
100.1	842
	843	Select [SLMP Connection Module] and add into host station as below picture shows;
	844
	845	Set Port number as 5002 (this is necessary settings);
	846
	847	Click [Close with Reflecting the Setting] to save and close window;
	848
109.1	849	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_14b489fdc6c6589d.png?width=600&height=350&rev=1.1\|\|alt="12.PLC Protocol_html_14b489fdc6c6589d.png" height="350" width="600"]]
100.1	850
	851	Click [Apply] to completed Etherenet settings;
	852
	853	Switch to the [On line data operation] interface as below, check the item and click [Execute] to download.
	854
109.1	855	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_c93025a968a8a9e7.png?width=600&height=434&rev=1.1\|\|alt="12.PLC Protocol_html_c93025a968a8a9e7.png" height="434" width="600"]]
100.1	856
110.1	857	4）Configure the communication protocol
	858
111.1	859	[[image:image-20220825112403-1.png]]
110.1	860
	861	5）Cable Wiring
	862
109.1	863	[[image:https://docs.we-con.com.cn/bin/download/PIStudio/12.PLC%20protocols/WebHome/12.PLC%20Protocol_html_2297240b57346b2a.png?width=401&height=170&rev=1.1\|\|alt="12.PLC Protocol_html_2297240b57346b2a.png" height="170" width="401"]]
100.1	864
26.1	865	= Delta PLC =
	866
64.1	867	== DVP Ethernet Protocol ==
1.1	868
	869	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
	870
63.1	871	== DVP Serial Protocol ==
1.1	872
	873	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Delta%20DVP%20Ethernet.zip]]
	874
48.1	875	= Omron PLC =
	876
65.1	877	== CP1 Series Protocol ==
7.1	878
8.1	879	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CP1%20Series.zip]]
7.1	880
65.1	881	== CJ2M Series Protocol ==
7.1	882
8.1	883	[[download link>>https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communication%20with%20ORMON%20CJ2M.zip]]
7.1	884
50.1	885	= Modbus RTU =
	886
53.1	887	== V-BOX as master ==
50.1	888
	889	Select the protocol “(% class="mark" %)Modbus RTU Slave(All Fuction)”,
	890
	891	(% class="mark" %)then set BaudRate,Port,Stop Bit,Data Bit,Parity
	892
	893	(% style="text-align:center" %)
	894	[[image:1624342015914-382.png\|\|height="486" width="800" class="img-thumbnail"]]
	895
53.1	896	== V-BOX as slave ==
50.1	897
	898	Select the protocol “(% class="mark" %)Modbus RTU Master”,
	899
	900	(% class="mark" %)then set BaudRate,Port,Stop Bit,Data Bit,Parity
	901
	902	(% style="text-align:center" %)
	903	[[image:1624348709622-711.png\|\|queryString="width=809&height=493" height="488" width="800" class="img-thumbnail"]]
	904
	905	Address List
	906
	907	(% class="table-bordered" %)
	908	\|Type\|Register\|Function code & Description
	909	\|(% rowspan="11" %)Word\|(% rowspan="3" %)3\|04 (read input register: read current binary value in one or more input registers)
	910	\|06 (write single register: write a binary value to a holding register)
	911	\|10 (write values to multiple addresses )
	912	\|(% rowspan="3" %)4\|03 (read holding register: read current binary value in one or more holding registers)
	913	\|06 (write single register: write a binary value to a holding register)
	914	\|10 (write values to multiple addresses )
	915	\|(% rowspan="3" %)W6\|03 (read holding register: read current binary value in one or more holding registers)
	916	\|06 (write single register: write a binary value to a holding register)
	917	\|10 (write values to multiple addresses )
	918	\|(% rowspan="2" %)W16\|03 (read holding register: read current binary value in one or more holding registers)
	919	\|10 (write values to multiple addresses )
	920	\|(% rowspan="11" %)Bit\|(% rowspan="3" %)0\|01 (Read coil state)
	921	\|05 (Force a single coil to force the on/off state of a logic coil)
	922	\|0F (Write multiple bits, ie write continuously)
	923	\|(% rowspan="3" %)1\|02 (Read the input state)
	924	\|05 (Force a single coil to force the on/off state of a logic coil)
	925	\|0F (Write multiple bits)
	926	\|(% rowspan="3" %)W5\|01 (Read coil state to obtain the current state of a set of logic coils)
	927	\|05 (Force a single coil to force the on/off state of a logic coil)
	928	\|0F (Write multiple bits)
	929	\|(% rowspan="2" %)W15\|01 (Read coil state to obtain the current state of a set of logic coils)
	930	\|0F (Write multiple bits)
	931
55.1	932	== communicate with VB inverter ==
52.1	933
	934	[[download link>>url:https://ftp.we-con.com.cn/Download/WIKI/V-BOX/Demo/%E9%80%9A%E8%AE%AF%E6%A1%88%E4%BE%8B/Communicate%20with%20VB%20inverter.zip]]
	935
51.1	936	= User define protocol =
1.1	937
19.1	938	More serial port script instruction,please refer manual:[[Lua script function>>doc:V-BOX.V-Net.Manual.04 Lua Script.01 Lua Functions.WebHome]]~-~-->[[3.Serial port operation>>url:http://docs.we-con.com.cn/wiki/vbox/view/HMI/04.Lua%20script%20%20function%20and%20operation/01.Lua%20script%20function/#H3.Serialportoperation]]
1.1	939
10.1	940	== Read the temperature sensor. ==
1.1	941
	942	the commond format is as beliow:
	943
	944	Send commond:01 03 02 00 00 03 04 73
	945
	946	Feedback commond:01 03 06 07 F7 0E 7E B7 35
	947
	948	Temperature data:07 F7,desimal = 2039,it means temperature is 20.39℃.
	949
	950	Humidity data:0E 7E,desimal = 3710, it mean humidity is 37.10%RH.
	951
	952	Script Demo:
	953
	954	~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~--
	955
	956	function com.main()
	957	~-~-dosomething
	958	openPlc()
	959	end
	960	function openPlc()
	961	if obj then
	962	~-~- If the serial port opened,then read/write data by timing
	963
	964	local wri = string.pack(">HHHH",0X0103,0X0200,0X0003,0X0473)
	965	local arr = reading(wri)
	966	~-~- if arr ~~=nil then
	967	~-~- if arr[1] ==33 and arr[2] ==v[2][2] and arr[3] ==v[2][3] then
	968	~-~- local A = arr[4]*256
	969	~-~- local B = A+arr[5]
	970	~-~- addr_setword(v[1],B)
	971	~-~- end
	972	~-~- end
	973
	974	else
	975	~-~-judge if there is a serial object, then initialize and open the serial port
	976	local configs = {
	977	name = 'COM1', ~-~-Select serial port COM1
	978	mode = 485, ~-~-Communication mode RS485
	979	baud_rate = 9600, ~-~-Baud rate 9600
	980	stop_bit = 1, ~-~-stop bit 1
	981	data_len = 8, ~-~-data length 8
	982	check_bit = 'NONE', ~-~-no parity
	983
	984	}
	985	obj,err = serial.open(configs) ~-~-Open serial port
	986	if not obj then
	987	print("serial open :failed", err) ~-~- Open serial port failed
	988	end
	989	end
	990	end
	991
	992	function reading(wri)
	993	obj:flush() ~-~- Clear serial port
	994	obj:write(wri) ~-~- Write serial port
	995	print(string.byte(wri,1,#wri))
	996	obj:flush() ~-~- Clear serial port
	997	local readed =obj:read(9,1000) ~-~- Read 9 bytes, timeout 1 second
	998	if readed and readed ~~= "" then
	999	~-~- judge that a non-empty string is read
	1000	print(string.byte(readed,1,#readed))
	1001	a={string.byte(readed, 1, #readed)}
	1002	if nil ~~= a[4] and nil ~~= a[5] and nil ~~= a[6] and nil ~~= a[7] then
	1003	a1=a[4]*256+a[5]
	1004	a2=a[6]*256+a[7]
	1005	addr_setword("@HDW0",a1)
	1006	addr_setword("@HDW1",a2)
	1007	end
	1008	return {string.byte(readed, 1, #readed)}
	1009	elseif readed == nil then
	1010	print("serial read err:", err or "")
	1011	return nil
	1012	end
	1013	return nil
	1014	end
	1015
	1016	~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-

Wiki source code of 1 Communication

Navigation

Table of Contents