Skip to Content
Last modified by Theodore Xu on 2025/02/21 14:13
From version 17.1
edited by Mora Zhou
on 2023/11/20 14:38
Change comment: There is no comment for this version
To version 21.1
edited by Theodore Xu
on 2024/03/27 09:37
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Mora
1 +XWiki.AiXia
Content
... ... @@ -1,4 +1,4 @@
1 -= 1 F0 group basic parameters =
1 += F0 group basic parameters =
2 2  
3 3  (% class="table-bordered" %)
4 4  |(% rowspan="3" %)**F0.00**|(% colspan="2" %)Motor control mode|Default|0
... ... @@ -86,10 +86,8 @@
86 86  
87 87  The set frequency is given by the terminal pulse.
88 88  
89 -Pulse given signal specifications: voltage range 9V~~30V, frequency range 0kHz~~100kHz.
89 +Pulse given signal specifications: voltage range 9V~~30V, frequency range 0kHz~~20kHz.
90 90  
91 -Note: Pulse reference can only be input from the multi-function input terminal, __**requires custom control board development.**__
92 -
93 93  **6: **Multi-stage speed
94 94  
95 95  Select multi-stage speed operation mode. Need to set the F5 group "input terminals" and FD group "multi-stage speed and PLC" parameters to determine the corresponding relationship between the given signal and the given frequency.
... ... @@ -263,7 +263,7 @@
263 263  |(% rowspan="2" style="width:139px" %)** F0.16**|(% style="width:680px" %)Carrier Frequency|(% style="width:429px" %)Default|(% style="width:204px" %)Model Dependent
264 264  |(% style="width:680px" %)Setting Range|(% colspan="2" style="width:633px" %)0.5kHz~~16.0kHz
265 265  
266 -= Carrier Frequency: =
264 += Carrier frequency =
267 267  
268 268  This function adjusts the carrier frequency of the AC drive. By adjusting the carrier frequency, the motor noise can be reduced, the resonance point of the mechanical system can be avoided, the leakage current of the line to the ground and the interference caused by the inverter can be reduced.
269 269  
... ... @@ -392,7 +392,7 @@
392 392  
393 393  The decimal place of the control frequency related instruction, the default is 2 decimal places. After the parameter is set, the decimal place of the parameter associated with the frequency is automatically adjusted. This parameter is not affected by F0.20.
394 394  
395 -= 2 F1 group start & stop control =
393 += F1 group start & stop control =
396 396  
397 397  (% class="table-bordered" %)
398 398  |(% rowspan="4" %)**F1.00**|(% colspan="2" %)Starting mode|Default|0
... ... @@ -552,7 +552,7 @@
552 552  
553 553  Setting whether the AC drive has output when running frequency is 0
554 554  
555 -= 3 F2 group motor parameters =
553 += F2 group motor parameters =
556 556  
557 557  (% class="table-bordered" %)
558 558  |(% rowspan="5" %)**F2.00**|(% colspan="2" %)Motor type selection|Default|0
... ... @@ -646,7 +646,9 @@
646 646  
647 647  When F2.11 is set to 1 or 2 and then press the ENT key, "TUNE" is displayed and flashes at this time, and then press the RUN key to start parameter tuning, and the displayed "TUNE" stops flashing at this time. When the tuning is over, the display returns to the stop state interface. During the tuning process, you can press the STOP button to stop tuning. When the tuning is completed, the value of F2.11 automatically returns to 0.
648 648  
647 +{{info}}
649 649  **✎Note: Tuning can only be effective in keyboard control mode, and the factory default value of acceleration and deceleration time is recommended.**
649 +{{/info}}
650 650  
651 651  (% class="table-bordered" %)
652 652  |(% rowspan="3" %)**F2.12**|(% colspan="2" %)G/P type selection|Default|Model dependent
... ... @@ -665,7 +665,7 @@
665 665  
666 666  The main and auxiliary winding currents can be changed by adjusting the single-phase motor turns ratio. Generally, reducing the single-phase motor turns ratio can increase the main winding current, reduce the auxiliary winding current, and reduce the motor heating (only effective when F2.00 = 3) .
667 667  
668 -= 4 F3 group vector control parameters =
668 += F3 group vector control parameters =
669 669  
670 670  F3 group function codes are only valid in vector control mode, that is, it is valid when F0.00=0, and it is invalid when F0.00=1.
671 671  
... ... @@ -802,7 +802,7 @@
802 802  
803 803  During startup, torque command 1 = F3.11 * F3.24 / 100; after maintaining time F3.25 seconds, it will be restored to torque command 2 = F3.11; torque command 1/2 switching requires torque acceleration and deceleration time F3.14/F3.15.
804 804  
805 -= 5 F4 group v/f control parameters =
805 += F4 group v/f control parameters =
806 806  
807 807  This group of function codes is only valid for V/F control (F0.00=1), and invalid for vector control.
808 808  
... ... @@ -971,7 +971,7 @@
971 971  
972 972  According to the actual use, select the situation where the AVR function is enabled.
973 973  
974 -= 6 F5 group input terminals =
974 += F5 group input terminals =
975 975  
976 976  The standard unit of the VB series inverter has 6 multi-function digital input terminals and 2 analog input terminals.
977 977  
... ... @@ -1208,7 +1208,7 @@
1208 1208  
1209 1209  Low Level:The connection between DI terminal and COM is invalid, while disconnection is valid.
1210 1210  
1211 -= 7 F6 group output terminals =
1211 += F6 group output terminals =
1212 1212  
1213 1213  The standard unit of VB series inverter has 2 multi-function relay output terminals, 1 FM terminal and 2 multi-function analog output terminals.
1214 1214  
... ... @@ -1468,7 +1468,7 @@
1468 1468  
1469 1469  Set the timer setting time
1470 1470  
1471 -= 8 F7 group keypad display =
1471 += F7 group keypad display =
1472 1472  
1473 1473  (% class="table-bordered" %)
1474 1474  |(% rowspan="4" %)**F7.00**|(% colspan="2" %)LCD keypad parameter copy|Default|0
... ... @@ -1679,7 +1679,7 @@
1679 1679  |(% rowspan="2" %)**F7.15**|Performance software version|Default|-
1680 1680  |Setting range|(% colspan="2" %)-
1681 1681  
1682 -= 9 F8 group auxiliary functions =
1682 += F8 group auxiliary functions =
1683 1683  
1684 1684  (% class="table-bordered" %)
1685 1685  |(% rowspan="2" %)**F8.00**|JOG running frequency|Default|2.00Hz
... ... @@ -1979,7 +1979,7 @@
1979 1979  
1980 1980  Enabling the fast current limiting function can minimize the inverter's overcurrent fault and protect the inverter from uninterrupted operation. After entering the fast current-limiting state for a period of time, a fast current-limiting fault (Err40) will be reported, indicating that the inverter is overloaded. Please refer to the handling of Err10.
1981 1981  
1982 -= 10 F9 group pid function of process control =
1982 += F9 group pid function of process control =
1983 1983  
1984 1984  PID control is a common method used in process control. It adjusts the output frequency of the inverter by performing proportional, integral, and differential calculations on the difference between the feedback signal of the controlled quantity and the target quantity signal to form a negative feedback system. The controlled amount is stable at the target amount. It is suitable for process control such as flow control, pressure control and temperature control. The basic control block diagram is as follows:
1985 1985  
... ... @@ -1986,6 +1986,9 @@
1986 1986  (% style="text-align:center" %)
1987 1987  [[image:CHAPTER 7 FUNCTIONAL PARAMETER DETAILS_html_972dcbcc01a1c9f6.png]]
1988 1988  
1989 +(% style="text-align:center" %)
1990 +[[image:生产流程图.png]]
1991 +
1989 1989  Figure 6-10-1 Block diagram of process PID principle
1990 1990  
1991 1991  (% class="table-bordered" %)
... ... @@ -2181,7 +2181,7 @@
2181 2181  
2182 2182  Figure 6-10-2 PID sleep and wake-up timing diagram
2183 2183  
2184 -= 11 FA group faults & protection =
2187 += FA group faults & protection =
2185 2185  
2186 2186  (% class="table-bordered" %)
2187 2187  |(% rowspan="3" %)**FA.00**|Motor overload protection selection|Default|1
... ... @@ -2416,7 +2416,7 @@
2416 2416  
2417 2417  Note: The function code display data is H.xxx, where H. means hexadecimal data.
2418 2418  
2419 -= 12 FB group frequency swing, length fixing and counting =
2422 += FB group frequency swing, length fixing and counting =
2420 2420  
2421 2421  The swing frequency function is suitable for textile, chemical fiber and other industries and occasions that require traverse and winding functions.
2422 2422  
... ... @@ -2503,7 +2503,7 @@
2503 2503  
2504 2504  Figure 6-12-2 Schematic diagram of set count value given and designated count value given
2505 2505  
2506 -= 13 FC group communication parameters =
2509 += FC group communication parameters =
2507 2507  
2508 2508  (% class="table-bordered" %)
2509 2509  |(% rowspan="2" %)**FC.00**|Local address|Default|1
... ... @@ -2554,7 +2554,7 @@
2554 2554  
2555 2555  Used to determine the output unit of the current value when the communication reads the output current.
2556 2556  
2557 -= 14 FD group muti-stage speed and simple plc functions =
2560 += FD group muti-stage speed and simple plc functions =
2558 2558  
2559 2559  The simple PLC function is that the inverter has a programmable controller (PLC) built in to complete automatic control of multi-segment frequency logic. The running time, running direction and running frequency can be set to meet the technological requirements. This series of inverters can realize 16-speed change control, and there are 4 kinds of acceleration and deceleration time for selection. When the set PLC completes a cycle, an ON signal can be output from the multifunctional digital output terminals DO1 and DO2 or multifunctional relay 1 and relay 2. See F1.02~~F1.05 for details. When the frequency source selection F0.07, F0.03, F0.04 is determined as the multi-speed operation mode, it is necessary to set FD.00~~FD.15 to determine its characteristics.
2560 2560  
... ... @@ -2713,7 +2713,7 @@
2713 2713  
2714 2714  This parameter determines the target quantity given channel of multi-speed 0.
2715 2715  
2716 -= 15 FE group user password management =
2719 += FE group user password management =
2717 2717  
2718 2718  (% class="table-bordered" %)
2719 2719  |(% rowspan="2" %)**FE.00**|User password|Default|0
生产流程图.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.AiXia
Size
... ... @@ -1,0 +1,1 @@
1 +1.0 MB
Content