Skip to Content
Last modified by Theodore Xu on 2025/02/21 14:13
From version 19.1
edited by Mora Zhou
on 2023/12/21 15:07
Change comment: There is no comment for this version
To version 16.1
edited by Theodore Xu
on 2023/11/13 11:58
Change comment: There is no comment for this version

Summary

Details

Page properties
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.Mora
1 +XWiki.AiXia
Content
... ... @@ -1,4 +1,4 @@
1 -= F0 group basic parameters =
1 += 1 F0 group basic parameters =
2 2  
3 3  (% class="table-bordered" %)
4 4  |(% rowspan="3" %)**F0.00**|(% colspan="2" %)Motor control mode|Default|0
... ... @@ -13,10 +13,7 @@
13 13  
14 14  It is suitable for occasions where the load requirements are not high or one AC drive drives multiple motors, such as fans and pumps.
15 15  
16 -(% class="box infomessage" %)
17 -(((
18 -**✎Note**: The motor parameter identification process must be carried out when selecting the SVC mode. Only accurate motor parameters can give full play to the advantages of it.
19 -)))
16 +**✎Note**: The motor parameter identification process must be carried out when selecting the SVC mode. Only accurate motor parameters can give full play to the advantages of it
20 20  
21 21  (% class="table-bordered" %)
22 22  |(% rowspan="4" %)**F0.01**|(% colspan="2" %)Command source selection|Default|0
... ... @@ -47,7 +47,7 @@
47 47  
48 48  This function is only valid for the digital setting of the frequency source. It is used to determine whether the set frequency is the current operating frequency or the current target frequency in UP/DOWN. .
49 49  
50 -(% class="table-bordered" style="width:1474px" %)
47 +(% class="table-bordered" %)
51 51  |(% rowspan="11" %)**F0.03**|(% colspan="2" %)Setting main frequency source X|Default|1
52 52  |(% rowspan="10" %)Setting Range|0|(% colspan="2" %)Digital setting (non-retentive at power failure)
53 53  |1|(% colspan="2" %)Digital setting (retentive at power failure)
... ... @@ -88,9 +88,7 @@
88 88  
89 89  Pulse given signal specifications: voltage range 9V~~30V, frequency range 0kHz~~100kHz.
90 90  
91 -{{info}}
92 -**✎**Note: Pulse reference can only be input from the multi-function input terminal, __**requires custom control board development.**__
93 -{{/info}}
88 +Note: Pulse reference can only be input from the multi-function input terminal, __**requires custom control board development.**__
94 94  
95 95  **6: **Multi-stage speed
96 96  
... ... @@ -135,8 +135,8 @@
135 135  
136 136  (% class="table-bordered" %)
137 137  |(% rowspan="3" %)**F0.05**|(% colspan="2" %)Range of auxiliary frequency source Y|Default|0
138 -|(% rowspan="2" style="width:494px" %)Setting Range|(% style="width:271px" %)0|(% colspan="2" %)Relative to the maximum frequency
139 -|(% style="width:271px" %)1|(% colspan="2" %)Relative to the frequency source X
133 +|(% rowspan="2" %)Setting Range|0|(% colspan="2" %)Relative to the maximum frequency
134 +|1|(% colspan="2" %)Relative to the frequency source X
140 140  |(% rowspan="2" %)**F0.06**|(% colspan="2" %)Percentage range of auxiliary frequency source Y|Default|0
141 141  |(% colspan="2" %)Setting Range|(% colspan="2" %)0%~~150%
142 142  
... ... @@ -159,13 +159,13 @@
159 159  
160 160  Use this parameter to select the frequency given channel. The frequency setting is realized by the combination of the main frequency source X and the auxiliary frequency source Y.
161 161  
162 -One’s digit: Selection of frequency source
157 +One’s digit:Selection of frequency source
163 163  
164 -0: Main frequency source X
159 +0:main frequency source X
165 165  
166 166  The main frequency X is used as the target frequency.
167 167  
168 -1: Main and auxiliary calculation results
163 +1: main and auxiliary calculation results
169 169  
170 170  The main and auxiliary calculation result is used as the target frequency (The calculation relationship is determined by the ten’s digits).
171 171  
... ... @@ -183,9 +183,9 @@
183 183  
184 184  4: Switchover between Y and main (X) & auxiliary(Y) calculation
185 185  
186 -When the multi-function input terminal 18: Frequency source switching is invalid, the auxiliary frequency source Y is taken as the target frequency.
181 +When the multi-function input terminal 18: frequency source switching is invalid, the auxiliary frequency source Y is taken as the target frequency.
187 187  
188 -When the multi-function input terminal 18: Frequency source switching is valid, the main and auxiliary calculation result is taken as the target frequency.
183 +When the multi-function input terminal 18: frequency source switching is valid, the main and auxiliary calculation result is taken as the target frequency.
189 189  
190 190  Ten’s digit:X and Y calculation relationship:
191 191  
... ... @@ -210,30 +210,30 @@
210 210  The result of multiplying the main frequency source X by the auxiliary frequency source Y is used as the target frequency.
211 211  
212 212  (% class="table-bordered" %)
213 -|(% rowspan="2" style="width:126px" %)**F0.08**|(% style="width:296px" %)Keypad setting frequency|(% style="width:525px" %)Default|(% style="width:504px" %)50.00Hz
214 -|(% style="width:296px" %)Setting Range|(% colspan="2" %)0.00~~Maximum frequency F0.10 (valid for digital setting for frequency source selection)
208 +|(% rowspan="2" %)**F0.08**|Keypad setting frequency|Default|50.00Hz
209 +|Setting Range|(% colspan="2" %)0.00~~Maximum frequency F0.10 (valid for digital setting for frequency source selection)
215 215  
216 216  When the frequency source is selected as "digital setting" or "terminal UP/DOWN", the function code value is the initial value of the frequency digital setting of the inverter.
217 217  
218 -(% class="table-bordered" style="width:1454px" %)
219 -|(% rowspan="3" style="width:134px" %)**F0.09**|(% colspan="2" style="width:825px" %)Running direction selection|(% style="width:405px" %)Default|(% style="width:117px" %)0
220 -|(% rowspan="2" style="width:288px" %)Setting Range|(% style="width:528px" %)0|(% colspan="2" style="width:513px" %)Forward direction
221 -|(% style="width:528px" %)1|(% colspan="2" style="width:513px" %)Reverse direction
213 +(% class="table-bordered" %)
214 +|(% rowspan="3" %)**F0.09**|(% colspan="2" %)Running direction selection|Default|0
215 +|(% rowspan="2" %)Setting Range|0|(% colspan="2" %)Forward direction
216 +|1|(% colspan="2" %)Reverse direction
222 222  
223 223  By changing this parameter, the rotation direction of the motor can be changed without changing any other parameters. Its function is equivalent to realizing the conversion of the rotation direction of the motor by adjusting any two cables of the motor (U, V, W).
224 224  
225 225  Tip: After the parameters are initialized, the motor running direction will return to the original state. Use it with caution when it is forbidden to change the rotation of the motor after the system is debugged.
226 226  
227 -(% class="table-bordered" style="width:1473px" %)
228 -|(% rowspan="2" style="width:135px" %)**F0.10**|(% colspan="2" style="width:815px" %)Maximum Frequency|(% style="width:376px" %)Default|50.00 Hz
229 -|(% colspan="2" style="width:815px" %)Setting Range|(% colspan="2" style="width:501px" %)50.00Hz~~500.00Hz
230 -|(% rowspan="7" style="width:135px" %)**F0.11**|(% colspan="2" style="width:815px" %)Source of frequency upper limit|(% style="width:376px" %)Default|0
231 -|(% rowspan="6" style="width:285px" %)Setting Range|(% style="width:530px" %)0|(% colspan="2" style="width:501px" %)Set by F0.12
232 -|(% style="width:530px" %)1|(% colspan="2" style="width:501px" %)AI1
233 -|(% style="width:530px" %)2|(% colspan="2" style="width:501px" %)AI2
234 -|(% style="width:530px" %)3|(% colspan="2" style="width:501px" %)Reserved
235 -|(% style="width:530px" %)4|(% colspan="2" style="width:501px" %)Reserved
236 -|(% style="width:530px" %)5|(% colspan="2" style="width:501px" %)Communication setting
222 +(% class="table-bordered" %)
223 +|(% rowspan="2" %)**F0.10**|(% colspan="2" %)Maximum Frequency|Default|50.00 Hz
224 +|(% colspan="2" %)Setting Range|(% colspan="2" %)50.00Hz~~500.00Hz
225 +|(% rowspan="7" %)**F0.11**|(% colspan="2" %)Source of frequency upper limit|Default|0
226 +|(% rowspan="6" %)Setting Range|0|(% colspan="2" %)Set by F0.12
227 +|1|(% colspan="2" %)AI1
228 +|2|(% colspan="2" %)AI2
229 +|3|(% colspan="2" %)Reserved
230 +|4|(% colspan="2" %)Reserved
231 +|5|(% colspan="2" %)Communication setting
237 237  
238 238  Define the source of the upper limit frequency. The upper limit frequency can come from the digital setting (F0.12) or the analog input channel. When using the analog input to set the upper limit frequency, 100% of the analog input setting corresponds to F0.12.
239 239  
... ... @@ -240,30 +240,30 @@
240 240  For example, in torque control, speed control is invalid. In order to avoid "overspeeding" due to material disconnection, the upper limit frequency can be set by analog. When the inverter runs to the upper limit frequency value, the torque control is invalid and the inverter continues to run at the upper limit frequency.
241 241  
242 242  (% class="table-bordered" %)
243 -|(% rowspan="2" style="width:138px" %)**F0.12**|(% style="width:814px" %)Frequency upper limit|(% style="width:113px" %)Default|50.00Hz
244 -|(% style="width:814px" %)Setting Range|(% colspan="2" style="width:500px" %)Frequency lower limit (F0.14)~~F0.10
245 -|(% rowspan="2" style="width:138px" %)**F0.13**|(% style="width:814px" %)Upper limit frequency offset|(% style="width:113px" %)Default|0.00Hz
246 -|(% style="width:814px" %)Setting Range|(% colspan="2" style="width:500px" %)0.00Hz ~~F0.10
238 +|(% rowspan="2" %)**F0.12**|Frequency upper limit|Default|50.00Hz
239 +|Setting Range|(% colspan="2" %)Frequency lower limit (F0.14)~~F0.10
240 +|(% rowspan="2" %)**F0.13**|Upper limit frequency offset|Default|0.00Hz
241 +|Setting Range|(% colspan="2" %)0.00Hz ~~F0.10
247 247  
248 248  When the upper limit frequency is given by the analog input, this parameter is used as the offset of the upper limit frequency calculation, and this upper limit frequency offset is added to the set value of the analog upper limit frequency as the final upper limit frequency setting value.
249 249  
250 250  (% class="table-bordered" %)
251 -|(% rowspan="2" style="width:136px" %)**F0.14**|(% style="width:670px" %)Frequency lower limit|(% style="width:217px" %)Default|0.00Hz
252 -|(% style="width:670px" %)Setting Range|(% colspan="2" style="width:491px" %)0.00Hz~~F0.12
246 +|(% rowspan="2" %)**F0.14**|Frequency lower limit|Default|0.00Hz
247 +|Setting Range|(% colspan="2" %)0.00Hz~~F0.12
253 253  
254 254  When the inverter starts to run, it starts from the starting frequency. If the given frequency is less than the lower limit frequency during operation, the inverter will run at the lower limit frequency, stop or run at zero speed. You can set which operating mode to use through F0.15.
255 255  
256 256  (% class="table-bordered" %)
257 -|(% rowspan="4" style="width:136px" %)**F0.15**|(% colspan="2" style="width:676px" %)The function of frequency lower limit|(% style="width:546px" %)Default|0
258 -|(% rowspan="3" style="width:488px" %)Setting Range|(% style="width:188px" %)0|(% colspan="2" style="width:640px" %)Running at frequency lower limit
259 -|(% style="width:188px" %)1|(% colspan="2" style="width:640px" %)Stop
260 -|(% style="width:188px" %)2|(% colspan="2" style="width:640px" %)Standby（Running at 0 Hz）
252 +|(% rowspan="4" %)**F0.15**|(% colspan="2" %)The function of frequency lower limit|Default|0
253 +|(% rowspan="3" %)Setting Range|0|(% colspan="2" %)Running at frequency lower limit
254 +|1|(% colspan="2" %)Stop
255 +|2|(% colspan="2" %)Standby（Running at 0 Hz）
261 261  
262 262  Select the running state of the AC drive when the set frequency is lower than the lower limit frequency. In order to prevent the motor from running at low speed for a long time, this function can be used to choose to stop.
263 263  
264 264  (% class="table-bordered" %)
265 -|(% rowspan="2" style="width:139px" %)** F0.16**|(% style="width:680px" %)Carrier Frequency|(% style="width:429px" %)Default|(% style="width:204px" %)Model Dependent
266 -|(% style="width:680px" %)Setting Range|(% colspan="2" style="width:633px" %)0.5kHz~~16.0kHz
260 +|(% rowspan="2" %)** F0.16**|Carrier Frequency|Default|Model Dependent
261 +|Setting Range|(% colspan="2" %)0.5kHz~~16.0kHz
267 267  
268 268  = Carrier Frequency: =
269 269  
... ... @@ -394,7 +394,7 @@
394 394  
395 395  The decimal place of the control frequency related instruction, the default is 2 decimal places. After the parameter is set, the decimal place of the parameter associated with the frequency is automatically adjusted. This parameter is not affected by F0.20.
396 396  
397 -= F1 group start & stop control =
392 += 2 F1 group start & stop control =
398 398  
399 399  (% class="table-bordered" %)
400 400  |(% rowspan="4" %)**F1.00**|(% colspan="2" %)Starting mode|Default|0
... ... @@ -554,7 +554,7 @@
554 554  
555 555  Setting whether the AC drive has output when running frequency is 0
556 556  
557 -= F2 group motor parameters =
552 += 3 F2 group motor parameters =
558 558  
559 559  (% class="table-bordered" %)
560 560  |(% rowspan="5" %)**F2.00**|(% colspan="2" %)Motor type selection|Default|0
... ... @@ -648,9 +648,7 @@
648 648  
649 649  When F2.11 is set to 1 or 2 and then press the ENT key, "TUNE" is displayed and flashes at this time, and then press the RUN key to start parameter tuning, and the displayed "TUNE" stops flashing at this time. When the tuning is over, the display returns to the stop state interface. During the tuning process, you can press the STOP button to stop tuning. When the tuning is completed, the value of F2.11 automatically returns to 0.
650 650  
651 -{{info}}
652 652  **✎Note: Tuning can only be effective in keyboard control mode, and the factory default value of acceleration and deceleration time is recommended.**
653 -{{/info}}
654 654  
655 655  (% class="table-bordered" %)
656 656  |(% rowspan="3" %)**F2.12**|(% colspan="2" %)G/P type selection|Default|Model dependent
... ... @@ -669,7 +669,7 @@
669 669  
670 670  The main and auxiliary winding currents can be changed by adjusting the single-phase motor turns ratio. Generally, reducing the single-phase motor turns ratio can increase the main winding current, reduce the auxiliary winding current, and reduce the motor heating (only effective when F2.00 = 3) .
671 671  
672 -= F3 group vector control parameters =
665 += 4 F3 group vector control parameters =
673 673  
674 674  F3 group function codes are only valid in vector control mode, that is, it is valid when F0.00=0, and it is invalid when F0.00=1.
675 675  
... ... @@ -806,7 +806,7 @@
806 806  
807 807  During startup, torque command 1 = F3.11 * F3.24 / 100; after maintaining time F3.25 seconds, it will be restored to torque command 2 = F3.11; torque command 1/2 switching requires torque acceleration and deceleration time F3.14/F3.15.
808 808  
809 -= F4 group v/f control parameters =
802 += 5 F4 group v/f control parameters =
810 810  
811 811  This group of function codes is only valid for V/F control (F0.00=1), and invalid for vector control.
812 812  
... ... @@ -975,7 +975,7 @@
975 975  
976 976  According to the actual use, select the situation where the AVR function is enabled.
977 977  
978 -= F5 group input terminals =
971 += 6 F5 group input terminals =
979 979  
980 980  The standard unit of the VB series inverter has 6 multi-function digital input terminals and 2 analog input terminals.
981 981  
... ... @@ -1212,7 +1212,7 @@
1212 1212  
1213 1213  Low Level:The connection between DI terminal and COM is invalid, while disconnection is valid.
1214 1214  
1215 -= F6 group output terminals =
1208 += 7 F6 group output terminals =
1216 1216  
1217 1217  The standard unit of VB series inverter has 2 multi-function relay output terminals, 1 FM terminal and 2 multi-function analog output terminals.
1218 1218  
... ... @@ -1472,7 +1472,7 @@
1472 1472  
1473 1473  Set the timer setting time
1474 1474  
1475 -= F7 group keypad display =
1468 += 8 F7 group keypad display =
1476 1476  
1477 1477  (% class="table-bordered" %)
1478 1478  |(% rowspan="4" %)**F7.00**|(% colspan="2" %)LCD keypad parameter copy|Default|0
... ... @@ -1683,7 +1683,7 @@
1683 1683  |(% rowspan="2" %)**F7.15**|Performance software version|Default|-
1684 1684  |Setting range|(% colspan="2" %)-
1685 1685  
1686 -= F8 group auxiliary functions =
1679 += 9 F8 group auxiliary functions =
1687 1687  
1688 1688  (% class="table-bordered" %)
1689 1689  |(% rowspan="2" %)**F8.00**|JOG running frequency|Default|2.00Hz
... ... @@ -1983,7 +1983,7 @@
1983 1983  
1984 1984  Enabling the fast current limiting function can minimize the inverter's overcurrent fault and protect the inverter from uninterrupted operation. After entering the fast current-limiting state for a period of time, a fast current-limiting fault (Err40) will be reported, indicating that the inverter is overloaded. Please refer to the handling of Err10.
1985 1985  
1986 -= F9 group pid function of process control =
1979 += 10 F9 group pid function of process control =
1987 1987  
1988 1988  PID control is a common method used in process control. It adjusts the output frequency of the inverter by performing proportional, integral, and differential calculations on the difference between the feedback signal of the controlled quantity and the target quantity signal to form a negative feedback system. The controlled amount is stable at the target amount. It is suitable for process control such as flow control, pressure control and temperature control. The basic control block diagram is as follows:
1989 1989  
... ... @@ -1990,9 +1990,6 @@
1990 1990  (% style="text-align:center" %)
1991 1991  [[image:CHAPTER 7 FUNCTIONAL PARAMETER DETAILS_html_972dcbcc01a1c9f6.png]]
1992 1992  
1993 -(% style="text-align:center" %)
1994 -[[image:生产流程图.png]]
1995 -
1996 1996  Figure 6-10-1 Block diagram of process PID principle
1997 1997  
1998 1998  (% class="table-bordered" %)
... ... @@ -2188,7 +2188,7 @@
2188 2188  
2189 2189  Figure 6-10-2 PID sleep and wake-up timing diagram
2190 2190  
2191 -= FA group faults & protection =
2181 += 11 FA group faults & protection =
2192 2192  
2193 2193  (% class="table-bordered" %)
2194 2194  |(% rowspan="3" %)**FA.00**|Motor overload protection selection|Default|1
... ... @@ -2423,7 +2423,7 @@
2423 2423  
2424 2424  Note: The function code display data is H.xxx, where H. means hexadecimal data.
2425 2425  
2426 -= FB group frequency swing, length fixing and counting =
2416 += 12 FB group frequency swing, length fixing and counting =
2427 2427  
2428 2428  The swing frequency function is suitable for textile, chemical fiber and other industries and occasions that require traverse and winding functions.
2429 2429  
... ... @@ -2510,7 +2510,7 @@
2510 2510  
2511 2511  Figure 6-12-2 Schematic diagram of set count value given and designated count value given
2512 2512  
2513 -= FC group communication parameters =
2503 += 13 FC group communication parameters =
2514 2514  
2515 2515  (% class="table-bordered" %)
2516 2516  |(% rowspan="2" %)**FC.00**|Local address|Default|1
... ... @@ -2561,7 +2561,7 @@
2561 2561  
2562 2562  Used to determine the output unit of the current value when the communication reads the output current.
2563 2563  
2564 -= FD group muti-stage speed and simple plc functions =
2554 += 14 FD group muti-stage speed and simple plc functions =
2565 2565  
2566 2566  The simple PLC function is that the inverter has a programmable controller (PLC) built in to complete automatic control of multi-segment frequency logic. The running time, running direction and running frequency can be set to meet the technological requirements. This series of inverters can realize 16-speed change control, and there are 4 kinds of acceleration and deceleration time for selection. When the set PLC completes a cycle, an ON signal can be output from the multifunctional digital output terminals DO1 and DO2 or multifunctional relay 1 and relay 2. See F1.02~~F1.05 for details. When the frequency source selection F0.07, F0.03, F0.04 is determined as the multi-speed operation mode, it is necessary to set FD.00~~FD.15 to determine its characteristics.
2567 2567  
... ... @@ -2720,7 +2720,7 @@
2720 2720  
2721 2721  This parameter determines the target quantity given channel of multi-speed 0.
2722 2722  
2723 -= FE group user password management =
2713 += 15 FE group user password management =
2724 2724  
2725 2725  (% class="table-bordered" %)
2726 2726  |(% rowspan="2" %)**FE.00**|User password|Default|0
生产流程图.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.AiXia
Size
... ... @@ -1,1 +1,0 @@
1 -1.0 MB
Content