Changes for page 06 Function parameter table

Summary

• Page properties (1 modified, 0 added, 0 removed)

Details

Page properties

Content

...	...	@@ -1,0 +1,2376 @@
	1	+○——It indicates that the set value of the parameter can be changed when the inverter is shut down or running.
	2	+
	3	+●——It indicates that the setting value of the parameter cannot be changed when the inverter is in operation;
	4	+
	5	+◎——It indicates that the value of the parameter is the actual detection record value and cannot be changed;
	6	+
	7	+□——It indicates that the parameter is Manufacturer parameter, which can only be set by the manufacturer and cannot be operated by users.
	8	+
	9	+
	10	+Mailing address description:
	11	+
	12	+The following table indicates the communication addresses in hexadecimal format.
	13	+
	14	+In the following table, the communication address is the RAM address, and the parameter is not saved if the power fails, you need to save, please see the instructions for writing EEPROM in section 7.4.
	15	+
	16	+
	17	+6.1 Basic parameter set
	18	+
	19	+|**Function code**|**Name**|**Setting range**|**Default**|**Property**|**Modbus address**
	20	+|(% colspan="6" %)**F0 Basic function parameter group**
	21	+|F0.00|Motor control mode|(((
	22	+0: SVC
	23	+
	24	+1: V/F
	25	+
	26	+2: -
	27	+)))|1|●|0x0000
	28	+|F0.01|Command source selection|(((
	29	+0: Operation panel command channel
	30	+
	31	+1: Terminal command channel
	32	+
	33	+2: Serial port communication command channel
	34	+)))|0|●|0x0001
	35	+|F0.02| UP/DOWN standard|(((
	36	+0: Operating frequency
	37	+
	38	+1: Set frequency
	39	+)))|1|●|0x0002
	40	+|F0.03|Primary frequency source X selection|(((
	41	+0: Digital setting F0.08 (Adjustable terminal UP/DOWN, non-relative after power failure)
	42	+
	43	+1: Digit setting F0.08 (Terminal
	44	+
	45	+UP/DOWN adjustable, power down memory)
	46	+
	47	+2: AI1
	48	+
	49	+3: AI2
	50	+
	51	+4: Keyboard potentiometer set
	52	+
	53	+5: The terminal PULSE pulse is set
	54	+
	55	+6: Multi-speed instruction
	56	+
	57	+7: Simple PLC
	58	+
	59	+8: PID
	60	+
	61	+9: Communication setting
	62	+
	63	+10: AI3(Expansion module)
	64	+)))|4|●|0x0003
	65	+|F0.04|Auxiliary frequency source Y selection|Same as F0.03|0|●|0x0004
	66	+|F0.05|Range of auxiliary frequency source Y|(((
	67	+0: Relative to the maximum frequency F0.10
	68	+
	69	+1: Relative to the frequency source X
	70	+)))|0|○|0x0005
	71	+|F0.06|Auxiliary frequency source Y range in superposition|0% to 150%|100%|○|0x0006
	72	+|F0.07|Frequency source operation selection|(((
	73	+LED ones: Frequency source
	74	+
	75	+selection
	76	+
	77	+0: The primary frequency source
	78	+
	79	+1: The result of primary and secondary operations
	80	+
	81	+2: Switch between primary frequency source and secondary frequency source
	82	+
	83	+3: Switch between the primary frequency source and the primary and secondary operation results
	84	+
	85	+4: Switch between auxiliary frequency source and primary and secondary operation results
	86	+
	87	+LED ten: Frequency source main and auxiliary operation relationship
	88	+
	89	+0: Primary + secondary
	90	+
	91	+1: Primary to secondary
	92	+
	93	+2: Indicates the maximum value of both
	94	+
	95	+3: The minimum value of both
	96	+
	97	+4: Main*auxiliary
	98	+)))|0|○|0x0007
	99	+|F0.08|Keyboard setting frequency|(((
	100	+0.00Hz to Maximum frequency
	101	+
	102	+F0.10
	103	+)))|50.00Hz|○|0x0008
	104	+|F0.09|Running direction selection|(((
	105	+0: The same direction
	106	+
	107	+1: The direction is reversed
	108	+
	109	+2: Reverse prohibition
	110	+)))|0|○|0x0009
	111	+|F0.10|Maximum output frequency|0.00Hz to 320.00Hz|50.00Hz|●|0x000A
	112	+|F0.11|Source of frequency upper limit|(((
	113	+0: The number is given F0.12
	114	+
	115	+1: AI1
	116	+
	117	+2: AI2
	118	+
	119	+3: AI3
	120	+
	121	+4: Set the terminal PULSE
	122	+
	123	+5: Communication setting
	124	+
	125	+6: Reservations
	126	+
	127	+7: Keyboard potentiometer set
	128	+)))|0|●|0x000B
	129	+|F0.12|Upper limiting frequency|F0.14 to F0.10|50.00Hz|○|0x000C
	130	+|F0.13|Upper frequency bias|0.00Hz to F0.10|0.00Hz|○|0x000D
	131	+|F0.14|Lower frequency|0.00Hz to F0.12|0.00Hz|○|0x000E
	132	+|F0.15|Lower frequency operating mode|(((
	133	+0: Run at lower frequency
	134	+
	135	+1: STOP
	136	+
	137	+2: Zero speed operation
	138	+)))|0|○|0x000F
	139	+|F0.16|Carrier frequency|0.5kHz to 16.0kHz|Model determination|○|0x0010
	140	+|F0.17|Carrier PWM characteristic selection|(((
	141	+Bits: Select PWM mode
	142	+
	143	+0: Automatic switching;
	144	+
	145	+1: 7 waves;
	146	+
	147	+2: 5 waves;
	148	+
	149	+3: SPWM;
	150	+
	151	+LED ten: Carrier is associated with the output frequency
	152	+
	153	+0: Independent of output frequency
	154	+
	155	+1: It depends on the output frequency
	156	+
	157	+LED hundred: random PWM depth
	158	+
	159	+0: OFF
	160	+
	161	+1-8: Open, adjust depth
	162	+
	163	+LED kilobit: Over modulation option
	164	+
	165	+0: OFF
	166	+
	167	+1: ON
	168	+)))|1010|●|0x0011
	169	+|F0.18|Acceleration time 1|0.0s to 6500.0s|Model determination|○|0x0012
	170	+|F0.19|Deceleration time1|0.0s to 6500.0s|Model determination|○|0x0013
	171	+|F0.20|Parameter initialization|(((
	172	+0: No action is taken
	173	+
	174	+1: Restore factory value (Do not restore motor parameters)
	175	+
	176	+2: Clear the record information
	177	+
	178	+3: Restore factory value (Restore motor parameters)
	179	+)))|0|●|0x0014
	180	+|F0.23|Unit of acceleration and deceleration time|(((
	181	+0: 1 s
	182	+
	183	+1: 0.1s
	184	+
	185	+2: 01s
	186	+)))|1|●|0x0017
	187	+|F0.24|Acceleration and deceleration time reference frequency|(((
	188	+0: Maximum frequency (F0.10)
	189	+
	190	+1: Set the frequency
	191	+
	192	+2: 100 Hz
	193	+)))|0|●|0x0018
	194	+|F0.25|Fan control|(((
	195	+Bits: Start/stop control
	196	+
	197	+0: The fan runs after the inverter is powered on
	198	+
	199	+1: Shutdown is related to temperature, and operation is running
	200	+
	201	+2: Stop The fan stops, and the operation is related to temperature
	202	+
	203	+Tens place: Enables the speed adjustment function
	204	+
	205	+0: Off
	206	+
	207	+1: Enable
	208	+)))|01|○|0x0019
	209	+|F0.26|Frequency command decimal point|(((
	210	+1: 1 decimal place
	211	+
	212	+2: 2 decimal places
	213	+)))|2|●|0x001A
	214	+|F0.27|Modulation ratio coefficient|10.0-150.0%|100.0%|○|0x001B
	215	+|(% colspan="6" %)**F1 Start stop control parameter group**
	216	+|F1.00|Start-up operation mode|(((
	217	+LED bits: Boot mode
	218	+
	219	+0: Start directly from the start frequency
	220	+
	221	+1: Start after speed tracking and direction judgment
	222	+
	223	+2: The asynchronous machine starts with pre-excitation
	224	+)))|00|●|0x0100
	225	+|F1.01|Speed tracking mode|(((
	226	+LED ten: Speed tracking direction
	227	+
	228	+0: One to the stop direction
	229	+
	230	+1: One to the starting direction
	231	+
	232	+2: Automatic search
	233	+)))|0|●|0x0101
	234	+|F1.02|Speed tracking time|0.01 to 60.00s|1.00s|○|0x0102
	235	+|F1.03|Speed tracking current loop gain|0.00-100.00|10.00|○|0x0103
	236	+|F1.04|RPM tracking speed gain|0.01 to 10.00|2.00|○|0x0104
	237	+|F1.05|Speed tracking current|50 to 200%|150%|○|0x0105
	238	+|F1.06|Starting frequency|0.00-60.00Hz|0.00Hz|○|0x0106
	239	+|F1.07|Startup frequency duration|0.0-50.0s|0.0s|●|0x0107
	240	+|F1.08|Braking current before starting|0.0-150.0%|80.0%|●|0x0108
	241	+|F1.09|Braking time before starting|0.0-60.0s|0.0s|●|0x0109
	242	+|F1.10|Stop method|(((
	243	+0: Slow down and stop
	244	+
	245	+1: Free shutdown
	246	+)))|0|○|0x010A
	247	+|F1.11|Stop DC braking start frequency|0.00Hz -F0.10|0.00Hz|○|0x010B
	248	+|F1.12|Stop DC braking wait time|0.0s to 100.0s|0.0s|○|0x010C
	249	+|F1.13|Stop DC braking current|0.0% to 150.0%|80.0%|○|0x010D
	250	+|F1.14|Stop DC braking duration|0.0s to 100.0s|0.0s|○|0x010E
	251	+|F1.16|Energy consumption brake action voltage|115.0%-140.0%|130%|●|0x0110
	252	+|F1.17|Magnetic flux braking gain|10-150%|80%|○|0x0111
	253	+|F1.18|Magnetic flux braking operating voltage|110%-500%|120%|○|0x0112
	254	+|F1.19|Flux brake limiting|0-200%|20%|○|0x0113
	255	+|F1.20|Acceleration and deceleration selection|(((
	256	+0: Straight line
	257	+
	258	+1: S curve
	259	+)))|0|●|0x0114
	260	+|F1.21|S-curve initial acceleration rate|20.0%-100.0%|50.0%|●|0x0115
	261	+|F1.22|S-curve initial deceleration rate|20.0%-100.0%|50.0%|●|0x0116
	262	+|F1.23|Zero speed holding torque|0.0-150.0%|0|●|0x0117
	263	+|F1.24|Zero speed holding torque time|(((
	264	+0.0 to 6000.0s
	265	+
	266	+If the value is set to 6000.0s, the value remains unchanged without time limit.
	267	+)))|Model determination|●|0x0118
	268	+|F1.25|Start pre-excitation time|0.00-60.00s|0.20|○|0x0119
	269	+|F1.26|Shutdown frequency|0.00-60.00Hz|0.00Hz|○|0x011A
	270	+|F1.27|Power failure restart action selection|(((
	271	+0: Invalid
	272	+
	273	+1: Valid
	274	+)))|0|○|0x011B
	275	+|F1.28|Power failure restart waiting time|0.00-120.00s|0.50s|○|0x011C
	276	+|F1.29|Select the terminal running protection|(((
	277	+LED bits: Select the terminal run instruction when powering on
	278	+
	279	+0: The terminal running instruction is invalid during power-on.
	280	+
	281	+1: Terminal running instructions are valid during power-on
	282	+
	283	+LED ten: Run command given channel switch terminal run instruction selection
	284	+
	285	+0: The terminal running instruction is invalid
	286	+
	287	+1: The terminal instruction is valid when the terminal is cut in.
	288	+)))|11|○|0x011D
	289	+|(% colspan="6" %)**F2 Motor parameter group**
	290	+|F2.00|Motor type|(((
	291	+0: Asynchronous machine (AM)
	292	+
	293	+1: Permanent magnet synchronous motor(PM)
	294	+
	295	+2: Single-phase induction motor (VF control only)
	296	+)))|0|●|0x0200
	297	+|F2.01|Rated power of motor|0.1kW to 400.0kW|(% rowspan="10" %)Model determination|●|0x0201
	298	+|F2.02|Rated voltage of motor|1V to 440V|●|0x0202
	299	+|F2.03|Rated current of motor|0.1-2000.0A|●|0x0203
	300	+|F2.04|Rated frequency of motor|0.01Hz -F0.10|●|0x0204
	301	+|F2.05|Rated motor speed|1rpm to 65000rpm|●|0x0205
	302	+|F2.06|Motor stator resistance|0.001-65.000|●|0x0206
	303	+|F2.07|Motor rotor resistance|0.001-65.000|●|0x0207
	304	+|F2.08|Motor fixed rotor inductance|0.1-6500.0mH|●|0x0208
	305	+|F2.09|Mutual inductance of motor fixed rotor|0.1-6500.0mH|●|0x0209
	306	+|F2.10|Motor no-load current|0.1-650.0A|●|0x020A
	307	+|F2.11|Tuning selection|(((
	308	+0: No operation is performed
	309	+
	310	+1: Static tuning 1
	311	+
	312	+2: Full tuning
	313	+
	314	+3: Static tuning 2(AM calculated Lm)
	315	+)))|0|●|0x020B
	316	+|F2.12|G/P model|(((
	317	+0: Type G machine
	318	+
	319	+1: P-type machine
	320	+)))|Model determination|◎|0x020C
	321	+|F2.13|Single-phase motor turns ratio|10 -200%|100%|●|0x020D
	322	+|F2.14|Current calibration coefficient of single-phase motor|50 -200%|120%|●|0x020E
	323	+|F2.15|Number of motor poles|2-48|4|●|0x020F
	324	+|F2.16|Speed feedback or encoder type|(((
	325	+Units place: encoder type
	326	+
	327	+0: Expansion interface for IO module
	328	+
	329	+1: Standard ABZ encoder
	330	+
	331	+2: Resolver
	332	+
	333	+3: UVW encoder
	334	+
	335	+4: UVW encoder with reduced wiring
	336	+
	337	+Tens place: encoder Direction
	338	+
	339	+0: Direction same
	340	+
	341	+1: Direction opposite
	342	+
	343	+Hundreds place: break Detection
	344	+
	345	+0: Disable
	346	+
	347	+1: Enable
	348	+
	349	+Thousands Digit: Reserved
	350	+)))|0|●|0x0210
	351	+|F2.17|Photoelectric encoder line count|0-60000|2500|●|0x0211
	352	+|F2.18|PG disconnection detection time|0.000-60.000s|0.100sec|○|0x0212
	353	+|F2.19|Resolver pole pairs|2-128|2|●|0x0213
	354	+|F2.20|Encoder installation reduction ratio|0.100-50.000|1.000|●|0x0214
	355	+|F2.21|Encoder filter time|1-1000ms|10ms|●|0x0215
	356	+|F2.22|Stator resistance of synchronization|0.001-65.000 (0.0010hm)|(% rowspan="4" %)Model determination|●|0x0216
	357	+|F2.23|Synchronize d-axis inductance|0.01mH-655.35mH|●|0x0217
	358	+|F2.24|Synchronize Q-axis inductance|0.01mH-655.35mH|●|0x0218
	359	+|F2.25|Synchronize back electromotive force|0.1V-1000.0V|○|0x0219
	360	+|F2.28|High frequency injection voltage|0.1% to 100.0%|20.0%|●|0x021C
	361	+|F2.29|Back potential identification current|0.1% to 100.0%|50.0%|●|0x021D
	362	+|F2.31|Asynchronous no-load current per unit value|0.1%|(% rowspan="9" %)Model determination|●|0x021F
	363	+|F2.32|Per unit asynchronous stator resistance|0.01%|●|0x0220
	364	+|F2.33|Asynchronous rotor resistance per unit value|0.01%|●|0x0221
	365	+|F2.34|Asynchronous mutual inductance per unit value|0.1%|●|0x0222
	366	+|F2.35|Asynchronous leakage sensing per unit value|0.01%|●|0x0223
	367	+|F2.36|Per unit value of asynchronous leakage sensing coefficient|0.01%|●|0x0224
	368	+|F2.37|Synchronous stator resistance per unit value|0.01%|●|0x0225
	369	+|F2.38|Per unit value of synchronous D-axis inductance|0.01%|●|0x0226
	370	+|F2.39|Synchronous Q-axis inductance per unit value|0.01%|●|0x0227
	371	+|F2.40|Back electromotive force of synchronous motor|0.1V|300.0V|●|0x0228
	372	+|F2.41|Encoder mounting angle|0.1 °|0.0 °|●|
	373	+|(% colspan="6" %)**F3 Vector control parameter group**
	374	+|F3.00|ASR (Speed loop) proportional gain 1|0.00 to 100.00%|20%|○|0x0300
	375	+|F3.01|ASR (Velocity ring) integration time 1|0.01s to 10.00s|0.20|○|0x0301
	376	+|F3.02|Loss of velocity protection value|(((
	377	+0 to 5000ms
	378	+
	379	+(0 Turn off stall protection)
	380	+)))|0ms|○|0x0302
	381	+|F3.03|ASR filtering time 1|0.000 to 0.100s|0.000s|○|0x0303
	382	+|F3.04|ASR switching frequency 1|0.00 to 50.00Hz|5.00Hz|○|0x0304
	383	+|F3.05|ASR (Speed loop) proportional gain 2|0.00 to 100.00%|20%|○|0x0305
	384	+|F3.06|ASR (Velocity loop) integration time 2|0.01s to 10.00s|0.30|○|0x0306
	385	+|F3.07|Retain| |0|-|0x0307
	386	+|F3.08|ASR filtering time 2|0.000-0.100s|0.000s|○|0x0308
	387	+|F3.09|ASR switching frequency 2|0.00-50.00Hz|10.00Hz|●|0x0309
	388	+|F3.10|Slip compensation coefficient|0-250%|100%|●|0x030A
	389	+|F3.11|Maximum electric torque|0.0-250.0%|160.0%|○|0x030B
	390	+|F3.12|Maximum generating torque|0.0-250.0%|160.0%|○|0x030C
	391	+|F3.16|Current loop D axis proportional gain|0.1 to 10.0|1.0|●|0x0310
	392	+|F3.17|Current loop D axis integral gain|0.1 to 10.0|1.0|○|0x0311
	393	+|F3.18|Current loop Q axis proportional gain|0.1 to 10.0|1.0|○|0x0312
	394	+|F3.19|Current loop Q axis integral gain|0.1 to 10.0|1.0|○|0x0313
	395	+|F3.20|D-axis feed-forward gain|0.0-200.0%|50.0%|○|0x0314
	396	+|F3.21|Q-axis feed-forward gain|0.0-200.0%|50.0%|○|0x0315
	397	+|F3.22|Optimize the current loop bandwidth|0.0 to 99.99ms|2.00ms|○|0x0316
	398	+|F3.23|Current loop control word|0 to 65535|0|○|0x0317
	399	+|F3.24|Weak magnetic control current upper limit|0 to 200%|50%|●|0x0318
	400	+|F3.25|Weak magnetic control feed forward gain|0 to 500%|0%|●|0x0319
	401	+|F3.26|Weak magnetic control proportional gain|0 to 9999|500|○|0x031A
	402	+|F3.27|Weak magnetic control integral gain|0 to 9999|1000|○|0x031B
	403	+|F3.28|MTPA gain|0.0 to 500.0%|0.0%|○|0x031C
	404	+|F3.29|MTPA filtering time|0.0 to 999.9ms|100.0ms|○|0x031D
	405	+|F3.30|Magnetic flux compensation coefficient|0-500%|100%|○|0x031E
	406	+|F3.31|Open-loop vector observeration gain|0 to 9999|1024|○|0x031F
	407	+|F3.32|Open loop vector observation filtering time|1 to 100ms|20ms|○|0x0320
	408	+|F3.33|Open-loop vector compensates start frequency|0 to 100.0%|1.0%|○|0x0321
	409	+|F3.34|Open loop vector control word|0 to 9999|8|○|0x0322
	410	+|F3.35|Synchronous open loop starting mode|(((
	411	+0: Direct startup.
	412	+
	413	+1: Start at an Angle
	414	+)))|0|○|0x0323
	415	+|F3.36|Dc pull in time|1ms to 9999ms|500ms|○|0x0324
	416	+|F3.37|Synchronous open loop vector low-frequency boost|0-100.0%|20.0%|○|0x0325
	417	+|F3.38|Synchronous open loop vector high-frequency boost|0.0-100.0%|0.0%|○|0x0326
	418	+|F3.39|Low frequency boost to maintain frequency|0.0-100.0%|10.0%|○|0x0327
	419	+|F3.40|Low frequency increases cutoff frequency|0.0-100.0%|20.0%|○|0x0328
	420	+|F3.46|Speed/torque control mode|(((
	421	+0: Speed control
	422	+
	423	+1: Torque control
	424	+)))|0|●|0x032E
	425	+|F3.47|Torque given channel selection|(((
	426	+0: F3.48 is set
	427	+
	428	+1: AI1╳F3.48
	429	+
	430	+2: AI2╳F3.48
	431	+
	432	+3: AI3╳F3.48
	433	+
	434	+4: PUL╳F3.48
	435	+
	436	+5: Keyboard potentiometer given ╳F7.01
	437	+
	438	+6: RS485 communication given ╳F3.48
	439	+)))|0|●|0x032F
	440	+|F3.48|Torque keyboard numeric setting|0 to 200.0%|100.0%|○|0x0330
	441	+|F3.49|Torque direction selection|(((
	442	+Units: Torque direction setting
	443	+
	444	+0: The torque direction is positive
	445	+
	446	+1: The torque direction is negative
	447	+
	448	+Tens place: torque reversing setting
	449	+
	450	+0: Torque reversal is allowed
	451	+
	452	+1: Torque reversal is prohibited
	453	+)))|00|○|0x0331
	454	+|F3.50|Upper limit of output torque|F3.51 to 200.0%|150.0%|○|0x0332
	455	+|F3.51|Lower limit of output torque|0 to F3.50|0%|○|0x0333
	456	+|F3.52|Torque control forward speed limit selection|(((
	457	+0: F3.54 is set
	458	+
	459	+1: AI1╳F3.54
	460	+
	461	+2: AI2╳F3.54
	462	+
	463	+3: AI3╳F3.54
	464	+
	465	+4: PUL╳F3.54
	466	+
	467	+5: Keyboard potentiometer given ╳F3.54
	468	+
	469	+6: RS485 communication given ╳F3.54
	470	+)))|0s|○|0x0334
	471	+|F3.53|Torque control reversal speed limit selection|(((
	472	+0: F3.55 is set
	473	+
	474	+1: AI1╳F3.55
	475	+
	476	+2: AI2╳F3.55
	477	+
	478	+3: AI3╳F3.55
	479	+
	480	+4: PUL╳F3.55
	481	+
	482	+5: Keyboard potentiometer given ╳F3.55
	483	+
	484	+6: RS485 communication given ╳F3.55
	485	+
	486	+7: Purchase card
	487	+)))|0|○|0x0335
	488	+|F3.54|Torque control positive maximum speed limit|0.00 to upper limiting frequency|50.00Hz|○|0x0336
	489	+|F3.55|Torque control reversal maximum speed limit|0.00 to upper limiting frequency|50.00Hz|○|0x0337
	490	+|F3.56|Speed/torque switching delay|0.00 to 10.00s|0.01s|○|0x0338
	491	+|F3.57|Torque acceleration time|0.00 to 10.00s|0.01s|○|0x0339
	492	+|F3.58|Torque deceleration time|0.00 to 10.00s|0.01s|○|0x033A
	493	+|F3.59|Forward and reverse torque dead zone time|0.00 to 650.00s|0.00s|○|0x033B
	494	+|(% colspan="6" %)**F4 V/F control parameter group**
	495	+|F4.00|Linear VF curve selection|(((
	496	+0: Linear V/F curve;
	497	+
	498	+1: Multi-point V/F curve
	499	+
	500	+2: Square V/F curve
	501	+
	502	+3-11: 1.1-1.9 power VF curves, respectively;
	503	+
	504	+12: V/F fully separated mode
	505	+)))|0|●|0x0400
	506	+|F4.01|Manual torque lift|0.1-30.0%, 0 automatic torque boost|Model determination|○|0x0401
	507	+|F4.02|Torque boost cutoff frequency|0.00Hz -F0.10|50.00Hz|●|0x0402
	508	+|F4.03|Self-set frequency F1|0.00Hz to F4.05|3.00Hz|●|0x0403
	509	+|F4.04|Self-set voltage V1|0.0% to 100.0%|10.0%|●|0x0404
	510	+|F4.05|Self-set frequency F2|F4.03 to F4.07|5.00Hz|●|0x0405
	511	+|F4.06|Self-set voltage V2|0.0% to 100.0%|15.0%|●|0x0406
	512	+|F4.07|Self-set frequency F3|F4.05-F4.09|8.00Hz|●|0x0407
	513	+|F4.08|Self-set voltage V3|0.0% to 100.0%|22.0%|●|0x0408
	514	+|F4.09|Self-set frequency F4|F4.07-Rated frequency of motor F2.04|12.00Hz|●|0x0409
	515	+|F4.10|Self-set voltage V4|0.0% to 100.0%|31.0%|●|0x040A
	516	+|F4.11|Oscillation suppression gain|0.0 to 10.0|Model determination|○|0x040B
	517	+|F4.12|Oscillation suppression filtering time|1 to 1000ms|50ms|○|0x040C
	518	+|F4.14|Percentage of output voltage|25-100%|100%|●|(((
	519	+
	520	+
	521	+0x040E
	522	+)))
	523	+|F4.16|(((
	524	+AVR function
	525	+
	526	+
	527	+)))|(((
	528	+0: Invalid
	529	+
	530	+1: Only slowing down is not effective
	531	+
	532	+2: Only constant speed is effective
	533	+
	534	+3: Valid
	535	+)))|3|●|0x0410
	536	+|F4.17|EVF torque boost gain|0 to 500.0%|50.0%|○|0x0411
	537	+|F4.18|EVF torque boost filtering time|1 to 1000ms|20ms|○|0x0412
	538	+|F4.19|EVF slip compensation gain|0 to 500.0%|0.0%|○|0x0413
	539	+|F4.20|EVF slip compensation filtering time|1 to 1000ms|100ms|○|0x0414
	540	+|F4.21|Automatic energy saving selection|(((
	541	+Units bit: 0 is off, 1 is on
	542	+
	543	+Tens: Frequency change exit depth
	544	+
	545	+Hundreds place: Reserve
	546	+
	547	+Thousands: Reserve
	548	+)))|50|○|0x0415
	549	+|F4.22|Lower limit frequency of energy saving operation|0.0-100.0%|25.0%|○|0x0416
	550	+|F4.23|Energy saving and pressure reduction time|0.1-5000.0s|10.0s|○|0x0417
	551	+|F4.24|Lower limit of energy saving and pressure reduction|20.0-100.0%|30.0%|○|0x0418
	552	+|F4.25|Energy saving and pressure reduction rate|1 to 1000V/s|50V/s|○|0x0419
	553	+|F4.26|Voltage regulated proportional gain|0 to 100|20|○|0x041A
	554	+|F4.27|Voltage regulation integral gain|0 to 100|20|○|0x041B
	555	+|F4.30|Stabilizer proportional gain|0.1% to 100.0%|10.0%|○|0x041E
	556	+|F4.31|Stabilizer filtering time|1ms to 1000ms|50ms|○|0x041F
	557	+|F4.32|Low frequency current lift|0.0% to 200.0%|100.0%|○|0x0420
	558	+|F4.33|Low frequency boost maintenance frequency|0 to 100.0%|10.0%|○|0x0421
	559	+|F4.34|Low frequency current boosts the cutoff frequency|0 to 100.0%|30.0%|○|0x0422
	560	+|F4.35|D-axis current gain|0.0 to 100.0|2.0|○|0x0423
	561	+|F4.36|Q-axis current gain|0.0 to 100.0|2.0|○|0x0424
	562	+|F4.37|Magnetic flux set strength|0 to 500%|30%|○|0x0425
	563	+|F4.38|Magnetic flux control proportional gain|0 to 9999|500|○|0x0426
	564	+|F4.39|Magnetic flux controls the integral gain|0 to 9999|500|○|0x0427
	565	+|F4.40|Dc pull in time|1ms to 9999ms|1000ms|○|0x0428
	566	+|F4.41|Starting frequency|0.00Hz to 99.00Hz|3.00Hz|○|0x0429
	567	+|F4.42|Starting frequency time|0.0s- 999.0s|3.0s|○|0x042A
	568	+|F4.43|V/F Separate the output voltage source|(((
	569	+0: Function code F0.27 set
	570	+
	571	+1: AI1 is set
	572	+
	573	+2: AI2 is set
	574	+
	575	+3: Reservations
	576	+
	577	+4: Set the terminal PULSE
	578	+
	579	+5: Multi-speed
	580	+
	581	+6: Simple PLC
	582	+
	583	+7: PID
	584	+
	585	+8: Communication is given 100% corresponding to the rated voltage of the motor
	586	+)))|0|○|0x042B
	587	+|F4.44|V/F separation output voltage digital setting|0.0% to 100.0%|0|○|0x042C
	588	+|F4.45|V/F separation voltage rise time|0.0-1000.0s|1.0|○|0x042D
	589	+|F4.46|V/F separation voltage drop time|0.0-1000.0s|1.0|○|0x042E
	590	+|F4.47|V/F separate stop mode|(((
	591	+0: The voltage/frequency is simultaneously reduced to 0;
	592	+
	593	+1: The frequency decreases after the voltage drops to 0
	594	+)))|0|○|0x042F
	595	+|(% colspan="6" %)**F5 Enter the terminal parameter group**
	596	+|F5.00|DI1 Terminal function selection|(% rowspan="8" %)(((
	597	+0: Non-function
	598	+
	599	+0: Non-function
	600	+
	601	+1: FWD
	602	+
	603	+2: REV
	604	+
	605	+3: Three-wire operation control
	606	+
	607	+4: FJOG
	608	+
	609	+5: RJOG
	610	+
	611	+6: Terminal UP
	612	+
	613	+7: Terminal DOWN
	614	+
	615	+8: Free break
	616	+
	617	+9: RESET
	618	+
	619	+10: Running pause
	620	+
	621	+11: External fault input(NO)
	622	+
	623	+12: Multi-speed instruction terminal 1
	624	+
	625	+13: Multi-speed instruction terminal 2
	626	+
	627	+14: Multi-speed instruction terminal 3
	628	+
	629	+15: Multi-speed instruction terminal 4
	630	+
	631	+16: Acceleration and deceleration time select terminal 1
	632	+
	633	+17: Acceleration and deceleration time select terminal 2
	634	+
	635	+18: Frequency source switching (terminal, keyboard)
	636	+
	637	+19: The UP/DOWN setting clears zero
	638	+
	639	+20: Run the command to switch terminals
	640	+
	641	+21: Acceleration and deceleration prohibition
	642	+
	643	+22: PID pause
	644	+
	645	+23: PLC State reset
	646	+
	647	+24: Swing pause
	648	+
	649	+25: Counter input
	650	+
	651	+26: Counter reset
	652	+
	653	+27: Length count input
	654	+
	655	+28: Length reset
	656	+
	657	+29: Torque control prohibited
	658	+
	659	+30: PULSE impulse input(only DI4)
	660	+
	661	+31: Reverse
	662	+
	663	+32: Immediate DC braking
	664	+
	665	+33: The external fault is normally closed
	666	+
	667	+34: Reverse
	668	+
	669	+35: The direction of PID action is reversed
	670	+
	671	+36: External parking terminal 1
	672	+
	673	+37: Control command switching terminal
	674	+
	675	+38: PID integration pause terminal
	676	+
	677	+39: Main frequency source and preset frequency switching terminal
	678	+
	679	+40: Auxiliary frequency source and preset frequency switching terminal
	680	+
	681	+41: Retain
	682	+
	683	+42: Retain
	684	+
	685	+43: PID parameter switching terminal
	686	+
	687	+44: User-defined fault 1
	688	+
	689	+45: User-defined fault 2
	690	+
	691	+46: Speed control/torque control switch
	692	+
	693	+47: Emergency stop
	694	+
	695	+48: External parking terminal 2
	696	+
	697	+49: Decelerate DC braking
	698	+
	699	+50: The running time is cleared
	700	+
	701	+51: Timing enable
	702	+
	703	+52: Timing reset
	704	+)))|1|●|0x0500
	705	+|F5.01|DI2 Terminal function selection|2|●|0x0501
	706	+|F5.02|DI3 Terminal function selection|9|●|0x0502
	707	+|F5.03|DI4 Terminal function selection|12|●|0x0503
	708	+|F5.04|DI5 Terminal function selection (Extension)|0|●|0x0504
	709	+|F5.05|DI6 Terminal function selection (Extension)|0|●|0x0505
	710	+|F5.08|AI1 Indicates the DI terminal function|0|●|0x0508
	711	+|F5.09|AI2 Indicates the DI terminal function|0|●|0x0509
	712	+|F5.10|AI1 Input selection|(((
	713	+0: 0-10V
	714	+
	715	+3: 0-5V
	716	+
	717	+4: 0.5-4.5V
	718	+)))|0|●|0x050A
	719	+|F5.11|AI2 Input selection|(((
	720	+0: 0-10V
	721	+
	722	+1: 4-20mA
	723	+
	724	+2: 0-20mA
	725	+
	726	+3: 0-5V
	727	+
	728	+4: 0.5-4.5V
	729	+)))|1|●|0x050B
	730	+|F5.12|VDI1 terminal function selection|(% rowspan="3" %)(((
	731	+0: Non-function
	732	+
	733	+1: FWD
	734	+
	735	+2: REV
	736	+
	737	+3: Three-wire operation control
	738	+
	739	+4: FJOG
	740	+
	741	+5: RJOG
	742	+
	743	+6: Terminal UP
	744	+
	745	+7: terminal DOWN
	746	+
	747	+8: Free break
	748	+
	749	+9: RESET
	750	+
	751	+10: Running pause
	752	+
	753	+11: External fault input(NO)
	754	+
	755	+12: Multi-speed instruction terminal 1
	756	+
	757	+13: Multi-speed instruction terminal 2
	758	+
	759	+14: Multi-speed instruction terminal 3
	760	+
	761	+15: Multi-speed instruction terminal 4
	762	+
	763	+16: Acceleration and deceleration time select terminal 1
	764	+
	765	+17: Acceleration and deceleration time select terminal 2
	766	+
	767	+18: Frequency source switching (terminal, keyboard)
	768	+
	769	+19: The UP/DOWN setting clears zero
	770	+
	771	+20: Run the command to switch terminals
	772	+
	773	+21: Acceleration and deceleration prohibition
	774	+
	775	+22: PID pause
	776	+
	777	+23: PLC State reset
	778	+
	779	+24: Swing pause
	780	+
	781	+25: Counter input
	782	+
	783	+26: Counter reset
	784	+
	785	+27: Length count input
	786	+
	787	+28: Length reset
	788	+
	789	+29: Torque control prohibited
	790	+
	791	+30: PULSE impulse input(only DI4)
	792	+
	793	+31: Reverse
	794	+
	795	+32: Immediate DC braking
	796	+
	797	+33: The external fault is normally closed
	798	+
	799	+34: Reverse
	800	+
	801	+35: The direction of PID action is reversed
	802	+
	803	+36: External parking terminal 1
	804	+
	805	+37: Control command switching terminal
	806	+
	807	+38: PID integration pause terminal
	808	+
	809	+39: Main frequency source and preset frequency switching terminal
	810	+
	811	+40: Auxiliary frequency source and preset frequency switching terminal
	812	+
	813	+41: Reverse
	814	+
	815	+42: Reverse
	816	+
	817	+43: PID parameter switching terminal
	818	+
	819	+44: User-defined fault 1
	820	+
	821	+45: User-defined fault 2
	822	+
	823	+46: Speed control/torque control switch
	824	+
	825	+47: Emergency stop
	826	+
	827	+48: External parking terminal 2
	828	+
	829	+49: Decelerate DC braking
	830	+
	831	+50: The running time is cleared
	832	+
	833	+51: Timing enable
	834	+
	835	+52: Timing reset
	836	+)))|0|●|0x050C
	837	+|F5.13|VDI2 terminal function selection|0|●|0x050D
	838	+|F5.14|VDI3 terminal function selection|0|●|0x050E
	839	+|F5.15|DI filtering time|0.000s to 1.000s|0.010s|○|0x050F
	840	+|F5.16|Terminal command mode|(((
	841	+0: Two-wire type 1
	842	+
	843	+1: Two-wire type 2
	844	+
	845	+2: Three-wire type 1
	846	+
	847	+3: Three-wire type 2
	848	+)))|0|●|0x0510
	849	+|F5.17|UP/DOWN change rate|0.01Hz to 655.35Hz|0.50Hz|○|0x0511
	850	+|F5.18|AI1 minimum input|0.00V to F5.20|0.00V|○|0x0512
	851	+|F5.19|AI1 minimum input setting|-100.0% to +100.0%|0%|○|0x0513
	852	+|F5.20|AI1 maximum input|F5.18 to +10.00V|10.00V|○|0x0514
	853	+|F5.21|AI1 maximum input setting|-100.0% to +100.0%|100.0%|○|0x0515
	854	+|F5.22|AI1 filtering time|0.00s to 10.00s|0.10s|○|0x0516
	855	+|F5.23|AI2 minimum input|-10.00V to F5.25|2.00V|○|0x0517
	856	+|F5.24|AI2 minimum input setting|-100.0% to +100.0%|0%|○|0x0518
	857	+|F5.25|AI2 maximum input|F5.23 to +10.00V|10.00V|○|0x0519
	858	+|F5.26|AI2 maximum input setting|-100.0% to +100.0%|100.0%|○|0x051A
	859	+|F5.27|AI2 filtering time|0.00s to 10.00s|0.10s|○|0x051B
	860	+|F5.28|PULSE|0.00 to F5.30|0.00kHz|○|0x051C
	861	+|F5.29|PULSE input minimum frequency setting|0.00-100.00%|0%|○|0x051D
	862	+|F5.30|PULSE input maximum frequency|F5.28-50.00kHz|20.00kHz|○|0x051E
	863	+|F5.31|PULSE maximum frequency setting|0.00-100.00%|100.0%|○|0x051F
	864	+|F5.32|PULSE filtering time|0.00-10.00s|0.10s|○|0x0520
	865	+|F5.33|DI1 Enable delay time|0.0s to 360.0s|0.0s|○|0x0521
	866	+|F5.34|DI2 Enable delay time|0.0s to 360.0s|0.0s|○|0x0522
	867	+|F5.35|DI1 Forbidden delay time|0.0s to 360.0s|0.0s|○|0x0523
	868	+|F5.36|DI2 Forbidden delay time|0.0s to 360.0s|0.0s|○|0x0524
	869	+|F5.37|Enter terminal valid status setting 1|(((
	870	+0: Low level valid
	871	+
	872	+1: High level valid
	873	+
	874	+LED one place: D1 terminal
	875	+
	876	+LED tens place: D2 terminal
	877	+
	878	+LED hundreds place: D3 terminal
	879	+
	880	+LED thousands place: D4 terminal
	881	+)))|0|●|0x0525
	882	+|F5.38|Enter terminal valid status setting 2|(((
	883	+0: Low level valid
	884	+
	885	+1: High level valid
	886	+
	887	+LED one place: D5 terminal(expend)
	888	+
	889	+LED tens place: D6 terminal(expend)
	890	+)))|0|●|0x0526
	891	+|F5.39|Enter terminal valid status setting 3|(((
	892	+0: Low level valid
	893	+
	894	+1: High level valid
	895	+
	896	+LED one place: AI1
	897	+
	898	+LED tens place: AI2
	899	+
	900	+LED hundreds place: AI3(expend)
	901	+)))|0|●|0x0527
	902	+|F5.40|Analog input curve selection|(((
	903	+One place: AI1
	904	+
	905	+Tens place: AI2
	906	+
	907	+Hundreds place: AI3 (expend)
	908	+
	909	+0: Straight line (default)
	910	+
	911	+1: Curve 1
	912	+
	913	+2: Curve 2
	914	+)))|0|●|0x0528
	915	+|F5.41|Lower limit of curve 1|0.00 to F5.43|0.00V|○|0x0529
	916	+|F5.42|The lower limit of curve 1 is set accordingly|0.00 to 100.00%|0.0%|○|0x052A
	917	+|F5.43|Curve 1 inflection point 1 Input voltage|F5.41 to F5.45|3.00V|○|0x052B
	918	+|F5.44|Curve 1 inflection point 1 corresponds to the setting|0.00 to 100.00%|30.0%|○|0x052C
	919	+|F5.45|Curve 1 inflection point 2 Input voltage|F5.43 to F5.47|6.00V|○|0x052D
	920	+|F5.46|Curve 1 inflection point 2 corresponds to the setting|0.00 to 100.00%|60.0%|○|0x052E
	921	+|F5.47|Upper limit of curve 1|F5.45 to 10.00V|10.0V|○|0x052F
	922	+|F5.48|The upper limit of curve 1 is set accordingly|0.00 to 100.00%|100.0%|○|0x0530
	923	+|F5.49|Lower limit of curve 2|0.00 to F5.51|0.00V|○|0x0531
	924	+|F5.50|The lower limit of curve 2 is set accordingly|0.00 to 100.00%|0.0%|○|0x0532
	925	+|F5.51|Curve 2 Inflection point 1 Input voltage|F5.49 to F5.53|3.00V|○|0x0533
	926	+|F5.52|Curve 2 inflection point 1 corresponds to the setting|0.00 to 100.00%|30.0%|○|0x0534
	927	+|F5.53|Curve 2 Inflection point 2 Input voltage|F5.51 to F5.55|6.00V|○|0x0535
	928	+|F5.54|Curve 2 inflection point 2 corresponds to the setting|0.00 to 100.00%|60.0%|○|0x0536
	929	+|F5.55|Upper limit of curve 2|F5.53 to 10.00V|10.00V|○|0x0537
	930	+|F5.56|The upper limit of curve 2 is set accordingly|0.00 to 100.00%|100.0%|○|0x0538
	931	+|F5.57|AI3(Extension) is used to select the DI terminal function|(% rowspan="2" %)(((
	932	+0: Non-function
	933	+
	934	+1: FWD
	935	+
	936	+2: REV
	937	+
	938	+3: Three-wire operation control
	939	+
	940	+4: FJOG
	941	+
	942	+5: RJOG
	943	+
	944	+6: Terminal UP
	945	+
	946	+7: terminal DOWN
	947	+
	948	+8: Free break
	949	+
	950	+9: RESET
	951	+
	952	+10: Running pause
	953	+
	954	+11: External fault input(NO)
	955	+
	956	+12: Multi-speed instruction terminal 1
	957	+
	958	+13: Multi-speed instruction terminal 2
	959	+
	960	+14: Multi-speed instruction terminal 3
	961	+
	962	+15: Multi-speed instruction terminal 4
	963	+
	964	+16: Acceleration and deceleration time select terminal 1
	965	+
	966	+17: Acceleration and deceleration time select terminal 2
	967	+
	968	+18: Frequency source switching (terminal, keyboard)
	969	+
	970	+19: The UP/DOWN setting clears zero
	971	+
	972	+20: Run the command to switch terminals
	973	+
	974	+21: Acceleration and deceleration prohibition
	975	+
	976	+22: PID pause
	977	+
	978	+23: PLC State reset
	979	+
	980	+24: Swing pause
	981	+
	982	+25: Counter input
	983	+
	984	+26: Counter reset
	985	+
	986	+27: Length count input
	987	+
	988	+28: Length reset
	989	+
	990	+29: Torque control prohibited
	991	+
	992	+30: PULSE impulse input(only DI4)
	993	+
	994	+31: Retain
	995	+
	996	+32: Immediate DC braking
	997	+
	998	+33: The external fault is normally closed
	999	+
	1000	+34: Retain
	1001	+
	1002	+35: The direction of PID action is reversed
	1003	+
	1004	+36: External parking terminal 1
	1005	+
	1006	+37: Control command switching terminal
	1007	+
	1008	+38: PID integration pause terminal
	1009	+
	1010	+39: Main frequency source and preset frequency switching terminal
	1011	+
	1012	+40: Auxiliary frequency source and preset frequency switching terminal
	1013	+
	1014	+41: Retain
	1015	+
	1016	+42: Retain
	1017	+
	1018	+43: PID parameter switching terminal
	1019	+
	1020	+44: User-defined fault 1
	1021	+
	1022	+45: User-defined fault 2
	1023	+
	1024	+46: Speed control/torque control switch
	1025	+
	1026	+47: Emergency stop
	1027	+
	1028	+48: External parking terminal 2
	1029	+
	1030	+49: Decelerate DC braking
	1031	+
	1032	+50: The running time is cleared
	1033	+
	1034	+51: Timing enable
	1035	+
	1036	+52: Timing reset
	1037	+)))| |○|0x0539
	1038	+|F5.58|AI4 (Extension) is used to select the DI terminal function| | |
	1039	+|F5.59|(((
	1040	+
	1041	+
	1042	+AI3(Extension) Input selection
	1043	+)))|(((
	1044	+0: 0 to 10V
	1045	+
	1046	+1: 4 to 20mA
	1047	+
	1048	+2: 0 to 20mA
	1049	+
	1050	+3: 0 to 5V
	1051	+
	1052	+4: 0.5 to 4.5V
	1053	+)))|0| |0x053A
	1054	+|F5.60|AI4(Extension) Input selection|(((
	1055	+0: 0 to 10V
	1056	+
	1057	+1: 4 to 20mA
	1058	+
	1059	+2: 0 to 20mA
	1060	+
	1061	+3: 0 to 5V
	1062	+
	1063	+4: 0.5 to 4.5V
	1064	+)))|0| |0x053B
	1065	+|F5.61|AI3(Extended) lower limit|0 to F5.63|0.00V|○|0x053C
	1066	+|F5.62|AI3(Extended) lower limit is set accordingly|-100.0% to +100.0%|0.00%|○|0x053D
	1067	+|F5.63|AI3(Extended) Upper limit|F5.61 to +10.00V|10.00V|○|0x053E
	1068	+|F5.64|The AI3(Extended) upper limit corresponds to the setting|-100.0% to +100.0%|100.00%|○|0x053F
	1069	+|F5.65|AI3(Extended) filtering time|0.00-10.00s|0.10s|○|0x0540
	1070	+|F5.71|vX terminal valid state source|(((
	1071	+0: Internal connection with virtual vYn
	1072	+
	1073	+1: Whether the function code setting is valid.
	1074	+
	1075	+One place: Virtual VDI1
	1076	+
	1077	+Tens place: Virtual VDI2
	1078	+
	1079	+Hundred bit: Virtual VDI3
	1080	+
	1081	+Thousands: Reserved
	1082	+)))|0|○|0x0547
	1083	+|F5.72|Virtual vX terminal function code set valid status|(((
	1084	+0: Invalid;
	1085	+
	1086	+1: Valid
	1087	+
	1088	+Units bit: Virtual VDI1
	1089	+
	1090	+Tens place: Virtual VDI2
	1091	+
	1092	+Hundreds place: Virtual VDI3
	1093	+
	1094	+Thousands place: Reserved
	1095	+)))|0|○|0x0548
	1096	+|F5.73|Select the terminal action mode|(((
	1097	+LED one place: free shutdown terminal recovery mode
	1098	+
	1099	+0: Restore the original command after it is invalid
	1100	+
	1101	+1: The original instruction is not restored if invalid
	1102	+
	1103	+LED tens place: emergency stop terminal recovery mode
	1104	+
	1105	+0: Restore the original command after disconnection
	1106	+
	1107	+1: The original command is not restored after the disconnect
	1108	+
	1109	+LED hundreds place: Select terminal operation mode after fault reset
	1110	+
	1111	+0: The terminal control can be started directly
	1112	+
	1113	+1: Stop the terminal control before starting
	1114	+
	1115	+LED thousands place: Reserve
	1116	+)))|111|○|0x0549
	1117	+|(% colspan="6" %)**F6 Output terminal parameter group**
	1118	+|F6.00|FM terminal output selection|(((
	1119	+0: Pulse output
	1120	+
	1121	+1: Open collector output (FMR)
	1122	+)))|1|○|0x0600
	1123	+|F6.01|FMR open collector output selection|(% rowspan="7" %)(((
	1124	+0: No output
	1125	+
	1126	+1: The inverter is in operation
	1127	+
	1128	+2: Fault output (Fault shutdown)
	1129	+
	1130	+3: Frequency level detection FDT1 Output
	1131	+
	1132	+4: Frequency reaches
	1133	+
	1134	+5: Zero speed running 1
	1135	+
	1136	+6: Motor overload forecast alarm
	1137	+
	1138	+7: Inverter overload forecast alarm
	1139	+
	1140	+8: Set meter value reached
	1141	+
	1142	+9: The specified count value is reached
	1143	+
	1144	+10: Length reached
	1145	+
	1146	+11: The PLC cycle is complete
	1147	+
	1148	+12: The accumulated running time reaches
	1149	+
	1150	+13: Reservations
	1151	+
	1152	+14: Torque limit
	1153	+
	1154	+15: Ready to run
	1155	+
	1156	+16: AI1 > AI2
	1157	+
	1158	+17: The upper frequency reaches
	1159	+
	1160	+18: The lower limit frequency reaches 1
	1161	+
	1162	+19: Output in undervoltage state
	1163	+
	1164	+20: Communication control
	1165	+
	1166	+21: Positioning completed (reserved)
	1167	+
	1168	+22: Positioning close (reserved)
	1169	+
	1170	+23: Zero speed running 2
	1171	+
	1172	+24: The cumulative power-on time reaches
	1173	+
	1174	+25: Frequency level detection FDT2 output
	1175	+
	1176	+26: Frequency reaches 1 output
	1177	+
	1178	+27: Frequency reaches 2 output
	1179	+
	1180	+28: Current reaches 1 output
	1181	+
	1182	+29: Current reaches 2 output
	1183	+
	1184	+30: timed to reach output
	1185	+
	1186	+31: Reserved
	1187	+
	1188	+32: Reserved
	1189	+
	1190	+33: Running direction
	1191	+
	1192	+34: Reserved
	1193	+
	1194	+35: The module temperature reaches
	1195	+
	1196	+36: Reserved
	1197	+
	1198	+37: The lower limit frequency reaches 2
	1199	+
	1200	+38: Fault output 2
	1201	+
	1202	+39: Reserved
	1203	+
	1204	+40: The running time arrives
	1205	+
	1206	+41: User-defined output 1
	1207	+
	1208	+42: User-defined output 2
	1209	+
	1210	+43: Timer output
	1211	+
	1212	+44: Running forward
	1213	+
	1214	+45: Reverse running
	1215	+)))|0|○|0x0601
	1216	+|F6.02|Relay 1 output selection|2|○|0x0602
	1217	+|F6.03|Relay 2 output selection (Extended)|0|○|0x0603
	1218	+|F6.06|VDO1 output selection|0|●|0x0606
	1219	+|F6.07|VDO2 output selection|0|●|0x0607
	1220	+|F6.08|VDO3 output selection|0|●|0x0608
	1221	+|F6.09|Reserve| |-|0x0609
	1222	+|F6.10|AO Output signal selection|(((
	1223	+One place: AO1
	1224	+
	1225	+0: 0 to 10V
	1226	+
	1227	+1: 4.00 to 20.00mA
	1228	+
	1229	+2: 0.00 to 20.00mA
	1230	+
	1231	+Tens place: AO2 (expend)
	1232	+
	1233	+0: 0 to 10V
	1234	+
	1235	+1: 4.00 to 20.00mA
	1236	+
	1237	+2: 0.00 to 20.00mA
	1238	+)))|00|-|0x060A
	1239	+|F6.11|FMP (Pulse output terminal) output selection|(% rowspan="3" %)(((
	1240	+0: Run frequency
	1241	+
	1242	+1: Setting frequency
	1243	+
	1244	+2: Output current
	1245	+
	1246	+3: Output torque
	1247	+
	1248	+4: Output power
	1249	+
	1250	+5: Output voltage
	1251	+
	1252	+6: Reserve
	1253	+
	1254	+7: AI1
	1255	+
	1256	+8: AI2
	1257	+
	1258	+9: AI3(Expansion module)
	1259	+
	1260	+10: PULSE input value
	1261	+
	1262	+11: Reserve
	1263	+
	1264	+12: Communication setting
	1265	+
	1266	+13: Motor speed
	1267	+
	1268	+14: Output current (0-1000A, corresponding to 0-10V)
	1269	+
	1270	+15: Output voltage (0-1000V, corresponding to 0-10V)
	1271	+
	1272	+16: Bus voltage (0-1000V, corresponding to 0-10V)
	1273	+)))|0|○|0x060B
	1274	+|F6.12|AO1 Output selection|0|○|0x060C
	1275	+|F6.13|AO2 Output(expend)|0|○|0x060D
	1276	+|F6.14|FM frequency output upper limit|0.00 to 20.00kHz|20.00kHz|○|0x060E
	1277	+|F6.15|AO1 Minimum input|0.00V to F6.17|0.00V|○|0x060F
	1278	+|F6.16|AO1 Minimum input corresponds to setting|0.0% to +100.0%|0.0%|○|0x0610
	1279	+|F6.17|AO1 Maximum output|F6.15 to +10.00V|10.00V|○|0x0611
	1280	+|F6.18|AO1 The maximum output corresponds to the setting|0.0% to +100.0%|100.0%|○|0x0612
	1281	+|F6.19|AO2 Minimum output(expend)|0.00V to F6.21|0.00V|○|0x0613
	1282	+|F6.20|AO2 Minimum output correspondence settings (expend)|0.0% to +100.0%|0.0%|○|0x0614
	1283	+|F6.21|AO2 Maximum output(expend)|F6.19 to +10.00V|10.00V|○|0x0615
	1284	+|F6.22|AO2 Maximum output correspondence settings (expend)|0.0% to +100.0%|100.0%|○|0x0616
	1285	+|F6.23|FMR connecting delay time|0.0s to 3600.0s|0.0s|○|0x0617
	1286	+|F6.24|Relay 1 connecting delay time|0.0 to 3600.0s|0.0s|○|0x0618
	1287	+|F6.25|Relay 2 connecting delay time(expend)|0.0s to 3600.0s|0.0s|○|0x0619
	1288	+|F6.26|VDO connecting delay time|0.0 to 3600.0s|0.0s|○|0x061A
	1289	+|F6.27|FMR disconnect delay time|0.0s to 3600.0s|0.0s|○|0x061B
	1290	+|F6.28|Relay 1 disconnect delay time|0.0 to 3600.0s|0.0s|○|0x061C
	1291	+|F6.29|Relay 2 disconnect delay time(expend)|0.0s to 3600.0s|0.0s|○|0x061D
	1292	+|F6.30|VDO1 disconnect delay|0.0 to 3600.0s|0.0s|○|0x061E
	1293	+|F6.31|Output terminal valid status select 1|(((
	1294	+0: Positive logic
	1295	+
	1296	+1: Reverse logic
	1297	+
	1298	+One place: FDOR
	1299	+
	1300	+Tens place: RL1
	1301	+
	1302	+Hundreds place: RL2 (Extended)
	1303	+
	1304	+Thousands place: -
	1305	+)))|000|○|0x061F
	1306	+|F6.32|Virtual output terminal valid status Select 2|(((
	1307	+0: Positive logic
	1308	+
	1309	+1: Reverse logic
	1310	+
	1311	+One place: VDO1
	1312	+
	1313	+Tens place: VDO2
	1314	+
	1315	+Hundreds place: VDO3
	1316	+
	1317	+Thousands palce: -
	1318	+)))|000|○|0x0620
	1319	+|F6.33|User-defined output selection (EX) 1|(((
	1320	+0: The running frequency
	1321	+
	1322	+1: Set the frequency
	1323	+
	1324	+2: Bus voltage
	1325	+
	1326	+3: Output voltage
	1327	+
	1328	+4: Output current
	1329	+
	1330	+5: Output power
	1331	+
	1332	+6: Output torque
	1333	+
	1334	+7-8: Reserved
	1335	+
	1336	+9: AI1 input
	1337	+
	1338	+10: AI2 input
	1339	+
	1340	+11: AI3 input(expansion module)
	1341	+)))|0|○|0x0621
	1342	+|F6.34|User selected comparison method 1|(((
	1343	+Units: Compare test methods
	1344	+
	1345	+0: Equal to (EX == X1)
	1346	+
	1347	+1: The value is greater than or equal to
	1348	+
	1349	+2: Less than or equal to
	1350	+
	1351	+3: Interval comparison (X1 ≤ EX ≤ X2)
	1352	+
	1353	+4: Bit test (EX & X1=X2)
	1354	+
	1355	+Tens: output mode
	1356	+
	1357	+0: False value output
	1358	+
	1359	+1: Truth output
	1360	+)))|0|○|0x0622
	1361	+|F6.35|User-defined dead zone 1|0 to 65535|0|○|0x0623
	1362	+|F6.36|User-defined 1 output comparison value 1|0 to 65535|0|○|0x0624
	1363	+|F6.37|User defined 1 output comparison value 2|0 to 65535|0|○|0x0625
	1364	+|F6.38|User-defined output selection (EX) 2|(((
	1365	+0: The running frequency
	1366	+
	1367	+1: Set the frequency
	1368	+
	1369	+2: Bus voltage
	1370	+
	1371	+3: Output voltage
	1372	+
	1373	+4: Output current
	1374	+
	1375	+5: Output power
	1376	+
	1377	+6: Output torque
	1378	+
	1379	+7-8: Reserved
	1380	+
	1381	+9: AI1 input
	1382	+
	1383	+10: AI2 input
	1384	+
	1385	+11: AI3 input(Expansion module)
	1386	+)))|0|○|0x0626
	1387	+|F6.39|User defined comparison method 2|(((
	1388	+One place: Compare test methods
	1389	+
	1390	+0: Equal to (EX == X1)
	1391	+
	1392	+1: The value is greater than or equal to
	1393	+
	1394	+2: Less than or equal to
	1395	+
	1396	+3: Interval comparison (X1 ≤ EX ≤ X2)
	1397	+
	1398	+4: Bit test (EX & X1=X2)
	1399	+
	1400	+Tens: output mode
	1401	+
	1402	+0: False value output
	1403	+
	1404	+1: Truth output
	1405	+)))|0|○|0x0627
	1406	+|F6.40|User-defined dead zone 2|0 to 65535|0|○|0x0628
	1407	+|F6.41|User defined 2 output comparison value 1|0 to 65535|0|○|0x0629
	1408	+|F6.42|User defined 2 output comparison value 2|0 to 65535|0|○|0x062A
	1409	+|F6.43|Timer time unit|(((
	1410	+0: Second
	1411	+
	1412	+1: Min
	1413	+
	1414	+2: Hour
	1415	+)))|0|○|0x062B
	1416	+|F6.44|Timer maximum|0-65000 (No reset when the set value is 65000)|0|○|0x062C
	1417	+|F6.45|Timer set value|0-65000|0|○|0x062D
	1418	+|F6.46|Counter maximum|0-65000|0|○|0x062E
	1419	+|F6.47|Counter set value|0-65000|0|○|0x062F
	1420	+|(% colspan="6" %)**F7 Keyboard and display parameter group**
	1421	+|F7.00|LCD Keyboard parameter copy|(((
	1422	+0: No operation is performed
	1423	+
	1424	+1: The function parameters of the machine are uploaded to the LCD keyboard
	1425	+
	1426	+2: LCD keyboard function parameters download to the machine
	1427	+)))|0|○|0x0700
	1428	+|F7.01|ENT key function selection|(((
	1429	+0: ENT is invalid.
	1430	+
	1431	+1: Switch between the instruction channel of the operation panel and the remote instruction channel (the remote instruction channel includes communication and terminal control)
	1432	+
	1433	+2: Reverse switch
	1434	+
	1435	+3: Forward jog
	1436	+
	1437	+4: Reverse jog
	1438	+
	1439	+5: Menu mode switch
	1440	+
	1441	+6: Reverse operation
	1442	+)))|0|●|0x0701
	1443	+|F7.02|Keyboard STOP key range|(((
	1444	+LED one place: Terminal control selection
	1445	+
	1446	+0: The terminal instruction is invalid
	1447	+
	1448	+1: Valid for the terminal command
	1449	+
	1450	+LED tens place: Communication control selection
	1451	+
	1452	+0: The communication instruction is invalid.
	1453	+
	1454	+1: Valid for communication instructions
	1455	+
	1456	+LED hundreds place: Reserved
	1457	+
	1458	+LED thousands place: Reserved
	1459	+)))|0011|○|0x0702
	1460	+|F7.03|Keyboard run displays parameter 1|(((
	1461	+LED one place: First group display
	1462	+
	1463	+0: Output frequency
	1464	+
	1465	+1: Given frequency
	1466	+
	1467	+2: Bus voltage
	1468	+
	1469	+3: Output voltage
	1470	+
	1471	+4: Output current
	1472	+
	1473	+5: Output power
	1474	+
	1475	+6: Output torque
	1476	+
	1477	+7: DI input status
	1478	+
	1479	+8: DO output status
	1480	+
	1481	+9: AI1 voltage
	1482	+
	1483	+A: AI2 voltage
	1484	+
	1485	+B: AI3 voltage(expansion module)
	1486	+
	1487	+C: Reserved
	1488	+
	1489	+D: Reserved
	1490	+
	1491	+E: Motor speed
	1492	+
	1493	+F: PID setting
	1494	+
	1495	+LED tens place: second group display
	1496	+
	1497	+LED hundreds place: Third group display
	1498	+
	1499	+LED thousands place: Fourth group display
	1500	+)))|E420|○|0x0703
	1501	+|F7.04|Keyboard run displays parameter 2|(((
	1502	+LED one place: First group display
	1503	+
	1504	+0: Not displayed
	1505	+
	1506	+1: PID feedback
	1507	+
	1508	+2: PLC stage
	1509	+
	1510	+3: PULSE input pulse frequency
	1511	+
	1512	+4: Feedback speed
	1513	+
	1514	+5: Reserved
	1515	+
	1516	+6: Reserved
	1517	+
	1518	+7: Reserved
	1519	+
	1520	+8: Reserved
	1521	+
	1522	+9: Current power-on time
	1523	+
	1524	+A: Current running time
	1525	+
	1526	+B: Reserved
	1527	+
	1528	+C: Communication setting
	1529	+
	1530	+D: Reserved
	1531	+
	1532	+E: Main frequency X display
	1533	+
	1534	+F: Auxiliary frequency Y display
	1535	+
	1536	+LED ten: Second group display
	1537	+
	1538	+LED hundreds place: Third group display
	1539	+
	1540	+LED thousands place: Fourth group display
	1541	+)))|0000|○|0x0704
	1542	+|F7.05|Keyboard stop displays parameters|(((
	1543	+LED one place: First group display
	1544	+
	1545	+0: Output frequency
	1546	+
	1547	+1: Given frequency
	1548	+
	1549	+2: Bus voltage
	1550	+
	1551	+3: Output voltage
	1552	+
	1553	+4: Output current
	1554	+
	1555	+5: Output power
	1556	+
	1557	+6: Output torque
	1558	+
	1559	+7: DI input status
	1560	+
	1561	+8: DO output status
	1562	+
	1563	+9: AI1 voltage
	1564	+
	1565	+A: AI2 voltage
	1566	+
	1567	+B:AI3 voltage(Expansion module)
	1568	+
	1569	+C: Motor speed
	1570	+
	1571	+D: PID setting
	1572	+
	1573	+E: PID feedback
	1574	+
	1575	+F: PLC stage
	1576	+
	1577	+LED tens place: Second group display
	1578	+
	1579	+LED hundreds place: Third group display
	1580	+
	1581	+LED thousands place: Fourth group display
	1582	+)))|C421|○|0x0705
	1583	+|F7.06|Load speed display factor|0.001 to 65.000|1.000|○|0x0706
	1584	+|F7.07|Radiator temperature of inverter module|0℃- 100℃| |◎|0x0707
	1585	+|F7.08|Radiator temperature of rectifier bridge|0℃- 100℃| |◎|0x0708
	1586	+|F7.09|Cumulative running time|0h to 65535h| |◎|0x0709
	1587	+|F7.10|Product number|-| |◎|0x070A
	1588	+|F7.11|Software version|-| |◎|0x070B
	1589	+|F7.12|Reverse| | |◎|0x070C
	1590	+|F7.13|Total power-on time|0 to 65535h| |◎|0x070D
	1591	+|F7.14|High cumulative power consumption|(% rowspan="2" %)(((
	1592	+Power consumption
	1593	+
	1594	+~=F7.14*65535+F7.15
	1595	+
	1596	+Units: kWh
	1597	+)))| |◎|0x070E
	1598	+|F7.15|Low cumulative power consumption| |◎|0x070F
	1599	+|F7.16|Output power correction factor|0 to 100.0%|100.0%|○|0x0710
	1600	+|F7.17|Power display dimension selection|(((
	1601	+0 to Power display percentage ~(%)
	1602	+
	1603	+1 to Power display kilowatts (KW)
	1604	+)))|1|○|0x0711
	1605	+|(% colspan="6" %)F8 Auxiliary function parameter group
	1606	+|F8.00|JOG running frequency|0.00Hz -Maximum frequency F0.10|2.00Hz|○|0x0800
	1607	+|F8.01|JOG acceleration time|0.00s to 6500.0s|20.0s|○|0x0801
	1608	+|F8.02|JOG deceleration time|0.00s to 6500.0s|20.0s|○|0x0802
	1609	+|F8.03|Acceleration time 2|0.00s to 6500.0s|(% rowspan="7" %)Model determination|○|0x0803
	1610	+|F8.04|Deceleration time 2|0.00s to 6500.0s|○|0x0804
	1611	+|F8.05|Acceleration time 3|0.00s to 6500.0s|○|0x0805
	1612	+|F8.06|Deceleration time 3|0.00s to 6500.0s|○|0x0806
	1613	+|F8.07|Acceleration time 4|0.00s to 6500.0s|○|0x0807
	1614	+|F8.08|Deceleration time 4|0.00s to 6500.0s|○|0x0808
	1615	+|F8.09|Emergency stop deceleration time|0.00s to 6500.0s|○|0x0809
	1616	+|F8.10|Jump frequency 1|0.00Hz -Maximum frequency|0.00Hz|○|0x080A
	1617	+|F8.11|Jump frequency 2|0.00Hz -Maximum frequency|0.00Hz|○|0x080B
	1618	+|F8.12|Jump frequency amplitude|0.00Hz -Maximum frequency|0.00Hz|○|0x080C
	1619	+|F8.13|Forward-reverse dead zone time|0.0 to 120.0s|0.0s|○|0x080D
	1620	+|F8.14|The carrier frequency is adjusted with temperature|(((
	1621	+0: Temperature independent
	1622	+
	1623	+1: Temperature dependent
	1624	+)))|1|○|0x080E
	1625	+|F8.15|Terminal action is preferred|(((
	1626	+0: Invalid
	1627	+
	1628	+1: Valid
	1629	+)))|1|○|0x080F
	1630	+|F8.16|Setting of accumulated power-on arrive time|0h to 65000h|0h|○|0x0810
	1631	+|F8.17|Set the accumulative running arrival time|0h to 65000h|65000h|○|0x0811
	1632	+|F8.18|Setting of accumulated power-on arrive action|(((
	1633	+0: Continue to run
	1634	+
	1635	+1: Fault warning
	1636	+)))|0|●|0x0812
	1637	+|F8.19|Set the accumulative running time arrival action|(((
	1638	+0: Continue to run
	1639	+
	1640	+1: Fault warning
	1641	+)))|0|●|0x0813
	1642	+|F8.20|Arrival time of this run|0-65000min|0|○|0x0814
	1643	+|F8.21|The running time reaches the action selection|(((
	1644	+0: Continue to run
	1645	+
	1646	+1: Fault prompt
	1647	+)))|0|●|0x0815
	1648	+|F8.22|Frequency detection value(FDT1)|0.00-Maximum frequency|50.00Hz|○|0x0816
	1649	+|F8.23|Frequency detection lag value(FDT1)|0.00-Maximum frequency|0.00Hz|○|0x0817
	1650	+|F8.24|Frequency detection value(FDT2)|0.00-Maximum frequency|50.00Hz|○|0x0818
	1651	+|F8.25|Frequency detection lag value(FDT2)|0.00-Maximum frequency|0.00Hz|○|0x0819
	1652	+|F8.26|Frequency reaches the detect width|(((
	1653	+0.0% to 100.0%
	1654	+
	1655	+(Maximum frequency)
	1656	+)))|0.0%|○|0x081A
	1657	+|F8.27|Arbitrary arrival frequency detection value 1|0.00Hz-Maximum frequency|50.00Hz|○|0x081B
	1658	+|F8.28|Arbitrary arrival frequency detection amplitude 1|0.0% to 100.0% (Maximum frequency)|0.0%|○|0x081C
	1659	+|F8.29|Arbitrary arrival frequency detection value 2|0.00Hz-Maximum frequency|50.00Hz|○|0x081D
	1660	+|F8.30|Arbitrary arrival frequency detection amplitude 1|0.0% to 100.0% (Maximum frequency)|0.0%|○|0x081E
	1661	+|F8.31|Arbitrarily reach current1|(((
	1662	+0.0% to 300.0%
	1663	+
	1664	+(Motor rated current)
	1665	+)))|100.0%|○|0x081F
	1666	+|F8.32|Arbitrarily reach current 1 width|(((
	1667	+0.0% to 300.0%
	1668	+
	1669	+(Motor rated current)
	1670	+)))|0.0%|○|0x0820
	1671	+|F8.33|Arbitrarily reach current 2|(((
	1672	+0.0% to 300.0%
	1673	+
	1674	+(Motor rated current)
	1675	+)))|100.0%|○|0x0821
	1676	+|F8.34|Arbitrarily reach current 2 width|(((
	1677	+0.0% to 300.0%
	1678	+
	1679	+(Motor rated current)
	1680	+)))|0.0%|○|0x0822
	1681	+|F8.35|Zero current detection value|0.0% to 300.0%(Motor rated current)|5.0%|○|0x0823
	1682	+|F8.36|Zero current detection delay time|0 to 600.00s|0s|○|0x0824
	1683	+|F8.37|Software over current point (D0 output)|(((
	1684	+0.0% to 300.0%
	1685	+
	1686	+(AC drive rated current)
	1687	+)))|200.0%|○|0x0825
	1688	+|F8.38|Software over current detection delay time|0 to 600.00s|0s|○|0x0826
	1689	+|(% colspan="6" %)**F9 Functional parameter array**
	1690	+|F9.00|PID setting source|(((
	1691	+0: Keyboard number PID given F9.01
	1692	+
	1693	+1: AI1
	1694	+
	1695	+2: AI2
	1696	+
	1697	+3: Reserve
	1698	+
	1699	+4: Terminal pulse setting
	1700	+
	1701	+5: Communication setting
	1702	+
	1703	+6: Multi -stage speed setting
	1704	+
	1705	+7: Keyboard potentiometer setting
	1706	+)))|0|○|0x0900
	1707	+|F9.01|PID digital setting|0.0% to 100.0%|50.0%|○|0x0901
	1708	+|F9.02|PID feedback source|(((
	1709	+0: AI1
	1710	+
	1711	+1: AI2
	1712	+
	1713	+2: Reserve
	1714	+
	1715	+3: AI1-AI2
	1716	+
	1717	+4: Terminal pulse setting
	1718	+
	1719	+5: Communication setting
	1720	+
	1721	+6: AI1+AI2
	1722	+
	1723	+7: MAX(|AI1|, |AI2|)
	1724	+
	1725	+8: MIN(|AI1|, |AI2|)
	1726	+
	1727	+9: Keyboard potentiometer setting
	1728	+)))|0|○|0x0902
	1729	+|F9.03|PID control characteristics|(((
	1730	+LED units: Feedback characteristic selection
	1731	+
	1732	+0: Positive action
	1733	+
	1734	+1: Reaction
	1735	+
	1736	+LED tens: PID adjustment direction selection
	1737	+
	1738	+0: Reverse prohibition
	1739	+
	1740	+1: Reverse permit
	1741	+
	1742	+LED hundreds digit: Alignment selection
	1743	+
	1744	+0: Off-center alignment
	1745	+
	1746	+1: Center alignment
	1747	+
	1748	+LED kilobit: Reserve
	1749	+)))|0100|○|0x0903
	1750	+|F9.04|PID given feedback range|0 to 65535|1000|○|0x0904
	1751	+|F9.05|Proportional gain P1|0 to 1000.0|20.00|○|0x0905
	1752	+|F9.06|Integration time I1|0.00s to 10.00s|2.00s|○|0x0906
	1753	+|F9.07|Differential time D1|0.00s to 10.00s|0.00s|○|0x0907
	1754	+|F9.08|PID reverse cutoff frequency|0.00 to Maximum frequency F0.10|0.00Hz|○|0x0908
	1755	+|F9.09|PID deviation limit|0.0% to 100.0%|0.0%|○|0x0909
	1756	+|F9.10|PID differential limiting|0.00% to 100.00%|0.10%|○|0x090A
	1757	+|F9.11|PID given change time|0.00 to 100.00s|0s|○|0x090B
	1758	+|F9.12|PID feedback filtering time|0.00 to 60.00s|0.00s|○|0x090C
	1759	+|F9.13|PID output filtering time|0.00 to 60.00s|0.00s|○|0x090D
	1760	+|F9.14|Proportional gain P2|0.0 to 1000.0|20.00|○|0x090E
	1761	+|F9.15|Integration time I2|0.00s to 10.00s|2.00s|○|0x090F
	1762	+|F9.16|Differential time D2|0.00s to 10.00s|0.00s|○|0x0910
	1763	+|F9.17|PID parameter switching condition|(((
	1764	+0: Do not switch
	1765	+
	1766	+1: Terminal switching
	1767	+
	1768	+2: Automatic switching based on deviation
	1769	+)))|0|○|0x0911
	1770	+|F9.18|PID parameter switching deviation 1|0.0% to F9.19|20.0%|○|0x0912
	1771	+|F9.19|PID parameter switching deviation 2|F9.18 to 100.0%|80.0%|○|0x0913
	1772	+|F9.20|PID Initial frequency value|0.0% to 100.0%|0%|○|0x0914
	1773	+|F9.21|PID Frequency initial holding time|0.0 to 6500.0s|0.0s|○|0x0915
	1774	+|F9.23|Feedback wire break action selection|(((
	1775	+0: The PID continues to run and no fault is reported
	1776	+
	1777	+1: Stop and report fault (Manual reset)
	1778	+
	1779	+2: Continue PID operation, output alarm signal
	1780	+
	1781	+3: Run at the current frequency, output alarm signal
	1782	+
	1783	+4: Stop and report fault (Automatic reset)
	1784	+)))|0|○|0x0917
	1785	+|F9.24|Wire break alarm upper limit|F9.25 to 100.0%|100.0%|○|0x0918
	1786	+|F9.25|Line break alarm lower limit|0 to F9.24|0.0%|○|0x0919
	1787	+|F9.26|Feedback break detection time|0.0s to 120.0s|0.0s|○|0x091A
	1788	+|F9.27|PID stop operation|(((
	1789	+0: No operation at stop
	1790	+
	1791	+1: Operation at stop
	1792	+)))|0|○|0x091B
	1793	+|F9.28|PID function selection|(((
	1794	+0: Normal PID
	1795	+
	1796	+1: Dormant PID
	1797	+)))|0|○|0x091C
	1798	+|F9.29|PID sleep threshold|0.0% to 100.0%|60.0%|○|0x091D
	1799	+|F9.30|PID sleep delay|0.0 to 3600.0s|3.0s|○|0x091E
	1800	+|F9.31|PID wake-up threshold|0.0% to 100.0%|20.0%|○|0x091F
	1801	+|F9.32|PID wake up delay|0.0 to 3600.0s|3.0s|○|0x0920
	1802	+|F9.33|Dormancy detection frequency|0 to Upper limit frequency F0.12|25.00Hz|○|0x0921
	1803	+|F9.34|Minimum output|(((
	1804	+0: F0.14(Lower frequency)
	1805	+
	1806	+1: 0Hz
	1807	+)))| |●|0x0922
	1808	+|F9.35|Double output deviation reverse minimum|0.00-100.00%|1.00%|○|0x0923
	1809	+|F9.36|Double output deviation reverse maximum|0.00-100.00%|1.00%|○|0x0924
	1810	+|F9.37|PID integral attribute|(((
	1811	+Units place: integral separation
	1812	+
	1813	+0: Invalid
	1814	+
	1815	+1: Valid
	1816	+
	1817	+Tens: output to the limit, whether to stop integrating
	1818	+
	1819	+0: Continue to integrate
	1820	+
	1821	+1: Stop collecting points
	1822	+)))|0|○|0x0925
	1823	+|F9.38|PID Preset Switchover condition selection|(((
	1824	+0: Time
	1825	+
	1826	+1: Switch according to AI1 feedback value
	1827	+)))|0|○|0x0926
	1828	+|F9.39|PID Minimum value of AI feedback switching|0.0-F9.40|45.0%|○|0x0927
	1829	+|F9.40|PID AI feedback maximum switching value|F9.39-100.0%|55.0%|○|0x0928
	1830	+|(% colspan="6" %)**FA Fault and protection parameter group**
	1831	+|FA.00|Motor overload protection selection|(((
	1832	+0: Off
	1833	+
	1834	+1: On
	1835	+)))|1|○|0x0A00
	1836	+|FA.01|Motor overload protection factor|0.0-250.0%|100.0%|○|0x0A01
	1837	+|FA.02|Motor overload warning coefficient|20.0-250.0%|80.0%|○|0x0A02
	1838	+|FA.03|Overvoltage stall and overcurrent stall control selection|(((
	1839	+0: Off
	1840	+
	1841	+1: On
	1842	+
	1843	+Unit: Excessive suppression enable
	1844	+
	1845	+Tens: Over current suppression enable
	1846	+
	1847	+Hundreds: Judge the input of brakes
	1848	+
	1849	+Thousands: Excessive suppression of fast rising frequency
	1850	+)))|1111|○|0x0A03
	1851	+|FA.04|Over voltage protection voltage|110% to 150%|Model settings|○|0x0A04
	1852	+|FA.05|The Udc controls voltage loop gain|0.00 to 50.00|2.00|○|0x0A05
	1853	+|FA.06|The Udc controls current loop gain|0.00 to 50.00|2.00|○|0x0A06
	1854	+|FA.07|Overcurrent suppression point|50% to 200%|150%|○|0x0A07
	1855	+|FA.08|Overcurrent suppression gain|0.00 to 50.00|2.00|○|0x0A08
	1856	+|FA.09|Overcurrent suppression points|0.00 to 50.00|4.00|○|0x0A09
	1857	+|FA.10|Short -circuit detection|(((
	1858	+0: Invalid
	1859	+
	1860	+1: Valid
	1861	+)))|1|○|0x0A0A
	1862	+|FA.11|Input phase loss protection|(((
	1863	+0:Disable
	1864	+
	1865	+1: Enable
	1866	+)))|1|○|0x0A0B
	1867	+|FA.12|Output phase loss protection|(((
	1868	+0:Disable
	1869	+
	1870	+1: Enable
	1871	+)))|1|○|0x0A0C
	1872	+|FA.13|Input phase loss protection software detection level|0.0-999.9%|15.0%|○|0x0A0D
	1873	+|FA.14|PWM parameter setting|(((
	1874	+One place: Enable voltage prediction compensation
	1875	+
	1876	+Tens - place: PWM update mode
	1877	+
	1878	+0: Single sample update
	1879	+
	1880	+1: Double sample and double update
	1881	+
	1882	+Hundreds place: Random carrier mode
	1883	+
	1884	+0: Random carrier
	1885	+
	1886	+1: Random 0 vector
	1887	+)))|0010| |0x0A0E
	1888	+|FA.15|Hardware current and voltage protection|(((
	1889	+One place: Hardware current limit(CBC)
	1890	+
	1891	+0: Disable
	1892	+
	1893	+1: Enable
	1894	+
	1895	+Tens places: -
	1896	+
	1897	+Hundreds place: FAU filtering time
	1898	+
	1899	+1 to F
	1900	+
	1901	+Thousands place: TZ filtering time
	1902	+
	1903	+1 to F
	1904	+)))|0001|○|0x0A0F
	1905	+|FA.16|CBC protection point|100-220%|200%|○|0x0A10
	1906	+|FA.17|CBC overload protection time|1-5000ms|500ms|○|0x0A11
	1907	+|FA.18|Undervoltage threshold setting|40.0% to 100.0%|100.0%|○|0x0A12
	1908	+|FA.19|Reserve|-|Model determination|◎|0x0A13
	1909	+|FA.20|Number of failure recovery|0 to 5|0|○|0x0A14
	1910	+|FA.21|Interval for fault self-recovery|0.1 to 100.0s|1.0s|○|0x0A15
	1911	+|FA.22|Power loss ride-through selection|(((
	1912	+One place: Power loss ride-through selection function enable
	1913	+
	1914	+0: Disable
	1915	+
	1916	+1: Enabled
	1917	+
	1918	+Tens place: Power loss ride-through function selection
	1919	+
	1920	+0: Continue to operation
	1921	+
	1922	+1: Shut down
	1923	+)))|0000|○|0x0A16
	1924	+|FA.23|Instant stop non-stop enter voltage|40% to 150%|75%|○|0x0A17
	1925	+|FA.24|Instant stop non-stop stable voltage|60% to 150%|95%|○|0x0A18
	1926	+|(% colspan="6" %)FB Application parameter set
	1927	+|FB.00|Swing frequency control|(((
	1928	+LED one-place: Swing frequency control
	1929	+
	1930	+0: The swing frequency control is invalid
	1931	+
	1932	+1: Swing frequency control is valid
	1933	+
	1934	+LED tens place: Swing frequency input mode
	1935	+
	1936	+0: Automatic input
	1937	+
	1938	+1: Manual input
	1939	+
	1940	+LED hundreds-place: Swing control
	1941	+
	1942	+0: Variable swing
	1943	+
	1944	+1: Fixed swing
	1945	+
	1946	+LED thousands place: Reserved
	1947	+)))|0|●|0x0B00
	1948	+|FB.01|Swing preset frequency|0.00-Maximum frequency|0.00Hz|●|0x0B01
	1949	+|FB.02|Preset frequency duration|0.00-650.00s|0.00s|●|0x0B02
	1950	+|FB.03|Swing amplitude|0.0-100.0%|0.0%|●|0x0B03
	1951	+|FB.04|Jump frequency amplitude|0.0-50.0%|0.0%|●|0x0B04
	1952	+|FB.05|Swing frequency rise time|0.00-650.00s|5.00s|●|0x0B05
	1953	+|FB.06|Swing frequency drop time|0.00-650.00s|5.00s|●|0x0B06
	1954	+|(% colspan="6" %)FC Communication parameter group
	1955	+|FC.00|Local address|1 to 247, 0 is Broadcast address|1|○|0x0C00
	1956	+|FC.01|Baud rate|(((
	1957	+0: 300 bps
	1958	+
	1959	+1: 600 bps
	1960	+
	1961	+2: 1200 bps
	1962	+
	1963	+3: 2400 bps
	1964	+
	1965	+4: 4800 bps
	1966	+
	1967	+5: 9600 bps
	1968	+
	1969	+6: 19200 bps
	1970	+
	1971	+7: 38400 bps
	1972	+
	1973	+8: 57600 bps
	1974	+
	1975	+9: 115200 bps
	1976	+)))|5|○|0x0C01
	1977	+|FC.02|Modbus data format|(((
	1978	+0: (8.N.2) 8 data bits, no parity, 2 stop stops
	1979	+
	1980	+1: (8.E.1) 8 data bits, even parity, 1 stop position
	1981	+
	1982	+2: (8.O.1) 8 data bits, odd parity, 1 stop stop
	1983	+
	1984	+3: (8.N.1) 8 data bits, no parity, 1 stop stop
	1985	+)))|3|○|0x0C02
	1986	+|FC.03|Modbus Communication response delay|0ms to 20ms|2ms|○|0x0C03
	1987	+|FC.04|Modbus Communication timeout|0.0 (Invalid), 0.1s to 60.0s|0|○|0x0C04
	1988	+|FC.06|​Master-slave selection|(((
	1989	+LED units place: Modbus communication master-slave selection
	1990	+
	1991	+0: Slave 1: Host
	1992	+)))|0| |
	1993	+|FC.07|Communication ratio setting|0.00 to 5.00|1.00| |
	1994	+|FC.08|Modbus communication fault action mode selection|(((
	1995	+0: Alarm and free parking (manual reset)
	1996	+
	1997	+1: No alarm and continue running
	1998	+
	1999	+2: Alarm and free parking (automatic reset)
	2000	+
	2001	+3: Parking does not alarm (based on F1.10 parking)
	2002	+)))|1| |
	2003	+|FC.09|Modbus transfers response processing|(((
	2004	+Units place: Write operation response
	2005	+
	2006	+0: Response to the write operation
	2007	+
	2008	+1: No response to write operation
	2009	+
	2010	+Tens Place: Communication exception response​​
	2011	+
	2012	+0: Response to exception
	2013	+
	2014	+1: No response to exception
	2015	+
	2016	+Hundreds place: Communication exception response protocol​
	2017	+
	2018	+0:8001 1:83
	2019	+)))|000| |
	2020	+|FC.10|Hosts send selection|(((
	2021	+LED units place: 1st group sending frame selection
	2022	+
	2023	+LED tens place:2st group sending frame selection
	2024	+
	2025	+LED hunderds place: 3st group sending frame selection
	2026	+
	2027	+0: Invalid
	2028	+
	2029	+1: Running command given
	2030	+
	2031	+2: Host given frequency
	2032	+
	2033	+3: Host output frequency
	2034	+
	2035	+4: Host upper limit frequency
	2036	+
	2037	+6: Host output torque
	2038	+
	2039	+9: Host given PID A: Host feedback PID
	2040	+)))|0x21| |
	2041	+|FC.11|RS485 communication port configuration|(((
	2042	+0: Configure to Modbus Communication
	2043	+
	2044	+1: Quota is serial communication
	2045	+
	2046	+2: UART_OSC
	2047	+)))|0| |
	2048	+|(% colspan="6" %)**FD Multi -speed instructions and simple PLC parameter arrays**
	2049	+|FD.00|Multi-speed instruction 0|-100.0% to 100.0% (100.0% corresponds to maximum frequency F0.10)|0|○|0x0D00
	2050	+|FD.01|Multi-speed instruction 1|-100.0% to 100.0%|0|○|0x0D01
	2051	+|FD.02|Multi-speed instruction 2|-100.0% to 100.0%|0|○|0x0D02
	2052	+|FD.03|Multi-speed instruction 3|-100.0% to 100.0%|0|○|0x0D03
	2053	+|FD.04|Multi-speed instruction 4|-100.0% to 100.0%|0|○|0x0D04
	2054	+|FD.05|Multi-speed instruction 5|-100.0% to 100.0%|0|○|0x0D05
	2055	+|FD.06|Multi-speed instruction 6|-100.0% to 100.0%|0|○|0x0D06
	2056	+|FD.07|Multi-speed instruction 7|-100.0% to 100.0%|0|○|0x0D07
	2057	+|FD.08|Multi-speed instruction 8|-100.0% to 100.0%|0|○|0x0D08
	2058	+|FD.09|Multi -speed instruction 9|-100.0% to 100.0%|0|○|0x0D09
	2059	+|FD.10|Multi-speed instruction10|-100.0% to 100.0%|0|○|0x0D0A
	2060	+|FD.11|Multi-speed instruction11|-100.0% to 100.0%|0|○|0x0D0B
	2061	+|FD.12|Multi-speed instruction12|-100.0% to 100.0%|0|○|0x0D0C
	2062	+|FD.13|Multi-speed instruction13|-100.0% to 100.0%|0|○|0x0D0D
	2063	+|FD.14|Multi-speed instruction14|-100.0% to 100.0%|0|○|0x0D0E
	2064	+|FD.15|Multi-speed instruction15|-100.0% to 100.0%|0|○|0x0D0F
	2065	+|FD.16|PLC mode of operation|(((
	2066	+0: Stops after a single run
	2067	+
	2068	+1: Maintain the final value at the end of a single run
	2069	+
	2070	+2: Keep cycling
	2071	+)))|0|○|0x0D10
	2072	+|FD.17|PLC Power down memory selection|(((
	2073	+Ones Slot:
	2074	+
	2075	+0: Power failure does not memory
	2076	+
	2077	+1: Power failure memory
	2078	+
	2079	+Ten places:
	2080	+
	2081	+0: Stop and does not remember
	2082	+
	2083	+1: Shutdown memory
	2084	+)))|0|○|0x0D11
	2085	+|FD.18|Running time of simple PLC reference 0|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D12
	2086	+|FD.19|Acceleration/deceleration time of simple PLC reference 0|0 to 3|0|○|0x0D13
	2087	+|FD.20|Running time of simple PLC reference 1|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D14
	2088	+|FD.21|Acceleration/deceleration time of simple PLC reference 1|0 to 3|0|○|0x0D15
	2089	+|FD.22|Running time of simple PLC reference 2|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D16
	2090	+|FD.23|Acceleration/deceleration time of simple PLC reference 2|0 to 3|0|○|0x0D17
	2091	+|FD.24|Running time of simple PLC reference 3|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D18
	2092	+|FD.25|Acceleration/deceleration time of simple PLC reference 3|0 to 3|0|○|0x0D19
	2093	+|FD.26|Running time of simple PLC reference 4|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D1A
	2094	+|FD.27|Acceleration/deceleration time of simple PLC reference 4|0 to 3|0|○|0x0D1B
	2095	+|FD.28|Running time of simple PLC reference 5|0.0-6553.5(s/m/h)|0.0s(h)|○|0x0D1C
	2096	+|FD.29|Acceleration/deceleration time of simple PLC reference 5|0 to 3|0|○|0x0D1D
	2097	+|FD.30|Running time of simple PLC reference 6|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D1E
	2098	+|FD.31|Acceleration/deceleration time of simple PLC reference 6|0 to 3|0|○|0x0D1F
	2099	+|FD.32|Running time of simple PLC reference 7|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D20
	2100	+|FD.33|Acceleration/deceleration time of simple PLC reference 6|0 to 3|0|○|0x0D21
	2101	+|FD.34|Running time of simple PLC reference 8|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D22
	2102	+|FD.35|Acceleration/deceleration time of simple PLC reference 8|0 to 3|0|○|0x0D23
	2103	+|FD.36|Running time of simple PLC reference 9|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D24
	2104	+|FD.37|Acceleration/deceleration time of simple PLC reference 9|0 to 3|0|○|0x0D25
	2105	+|FD.38|Running time of simple PLC reference 10|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D26
	2106	+|FD.39|Acceleration/deceleration time of simple PLC reference 10|0 to 3|0|○|0x0D27
	2107	+|FD.40|Running time of simple PLC reference 11|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D28
	2108	+|FD.41|Acceleration/deceleration time of simple PLC reference 11|0 to 3|0|○|0x0D29
	2109	+|FD.42|Running time of simple PLC reference 12|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D2A
	2110	+|FD.43|Acceleration/deceleration time of simple PLC reference 12|0 to 3|0|○|0x0D2B
	2111	+|FD.44|Running time of simple PLC reference 13|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D2C
	2112	+|FD.45|Acceleration/deceleration time of simple PLC reference 13|0 to 3|0|○|0x0D2D
	2113	+|FD.46|Running time of simple PLC reference 14|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D2E
	2114	+|FD.47|Acceleration/deceleration time of simple PLC reference 14|0 to 3|0|○|0x0D2F
	2115	+|FD.48|Running time of simple PLC reference 15|0.0-6553.5 (s/m/h)|0.0s(h)|○|0x0D30
	2116	+|FD.49|Acceleration/deceleration time of simple PLC reference 15|0 to 3|0|○|0x0D31
	2117	+|FD.50|PLC Run-time unit|(((
	2118	+LED units: timing unit
	2119	+
	2120	+0: s(seconds)
	2121	+
	2122	+1: h(hours)
	2123	+
	2124	+2: min(minutes)
	2125	+)))|0|○|0x0D32
	2126	+|FD.51|Multi-segment speed instruction 0 given mode|(((
	2127	+0: Function code FD.00 is given
	2128	+
	2129	+1: AI1
	2130	+
	2131	+2: AI2
	2132	+
	2133	+3: AI3 (expansion)
	2134	+
	2135	+4: Terminal pulse PULSE given
	2136	+
	2137	+5: PID
	2138	+
	2139	+6: Preset frequency (F0.08) given, UP/DOWN modifiable
	2140	+
	2141	+7: Keyboard potentiometer given
	2142	+)))|0|○|0x0D33
	2143	+|FD.52|Multispeed priority|(((
	2144	+0: Invalid
	2145	+
	2146	+1: Valid
	2147	+)))|1|○|0x0D34
	2148	+|(% colspan="6" %)**FE User parameter group**
	2149	+|FE.00|User password|0 to 65535|0|○|0x0E00
	2150	+|FE.01|Fault record display times|0 to 8|4|○|0x0E01
	2151	+|FE.02|Parameter and key lock selection|(((
	2152	+0: Not locked
	2153	+
	2154	+1: The function parameter is locked
	2155	+)))|0|○|0x0E02
	2156	+|(% colspan="6" %)**A0 Application parameter group**
	2157	+|A0.00|Application macro|(((
	2158	+0:Default macro
	2159	+
	2160	+1: Pressure machine macro
	2161	+
	2162	+2: Spring machinery macro
	2163	+
	2164	+3: woodworking machinery macro
	2165	+)))|0|●|0xA000
	2166	+|(% colspan="6" %)**A4 Constant pressure water supply parameter group**
	2167	+|A4.00|Water supply function selection|(((
	2168	+0: Invalid
	2169	+
	2170	+1: Valid
	2171	+)))|0|●|0xA400
	2172	+|A4.01|Setting pressure|1.0 to A4.19|3.0bar|○|0xA401
	2173	+|A4.02|Starting pressure|0.0 to A4.01|0.3bar|○|0xA402
	2174	+|A4.03|Sensor range|1.0 to 200.0bar|16.0bar|○|0xA403
	2175	+|A4.04|Sensor feedback type|(((
	2176	+0: 4 to 20mA（AI2）
	2177	+
	2178	+1: 0 to 10V（AI1）
	2179	+)))|0|○|0xA404
	2180	+|A4.05|Pressure calibration factor|0.750 to 1.250|1.000|○|0xA405
	2181	+|A4.06|Proportional gain P|0.0 to 100.0|50.0|○|0xA406
	2182	+|A4.07|Integration time I|0.00s to 10.00s|0.50|○|0xA407
	2183	+|A4.08|Differential time|0.000s to 10.000s|0.000|○|0xA408
	2184	+|A4.09|Sleep time|(((
	2185	+0: Disable
	2186	+
	2187	+1: Sleep mode 1
	2188	+
	2189	+2: Sleep mode 2
	2190	+)))|(((
	2191	+
	2192	+
	2193	+1
	2194	+)))|○|(((
	2195	+
	2196	+
	2197	+0xA409
	2198	+)))
	2199	+|A4.10|Sleep delay|0.0s to 100.0s|5.0s|○|0xA40A
	2200	+|A4.11|Wake up delay|0.0s to 100.0s|3.0|○|0xA40B
	2201	+|A4.12|Low-frequency hold frequency|0.0 to A4.14|20.00Hz|○|0xA40C
	2202	+|A4.13|Low frequency hold frequency running time|0.0s to 100.0s|5.0s|○|0xA40D
	2203	+|A4.14|Sleep frequency|A4.12 to F0.12|25.00Hz|○|0xA40E
	2204	+|A4.15|Sleep detection cycle|0.0s to 600.0s|30.0s|○|0xA40F
	2205	+|A4.16|Leaking coefficient|0.1s to 100.0s|2.5s|○|0xA410
	2206	+|A4.17|Sleep detection coefficient|1 to 10|4|○|0xA411
	2207	+|A4.18|Deadband pressure|0.0bar to 1.0bar|0.1bar|○|0xA412
	2208	+|A4.19| High voltage alarm setting value|A4.00 to A4.03|15.0bar|○|0xA413
	2209	+|A4.20| Low voltage alarm setting value|0.0 to A4.01|0.0bar|○|0xA414
	2210	+|A4.21|Water pressure alarm delay time|0.0 to 100.0|3.0s|○|0xA415
	2211	+|A4.22|Sensor disconnection detection value|0.00 to 10.00V|0.20|○|0xA416
	2212	+|A4.23|Sensor disconnection detection time|0.0s to 100.0s|30.0s|○|0xA417
	2213	+|A4.24|Water shortage protection function|(((
	2214	+0: Disable
	2215	+
	2216	+1: Judging by frequency and current
	2217	+
	2218	+2: Judging by frequency and pressure
	2219	+)))|2|○|0xA418
	2220	+|A4.25|Water shortage fault detection threshold|0.00s to 10.00s|0.50|○|0xA419
	2221	+|A4.26|Water shortage protection detection frequency|0 to F0.12|48.00Hz|○|0xA41A
	2222	+|A4.27|Water shortage protection detection current percentage|0.0 to 100.0%|40.0%|○|0xA41B
	2223	+|A4.28|Water shortage protection detection time|0.0 to 200.0s|60.0s|○|0xA41C
	2224	+|A4.29|Water shortage protection automatic reset delay|0 to 1000|15|○|0xA41D
	2225	+|A4.30|Number of Auto-resets for water shortage protection|0 to 100|10|○|0xA41E
	2226	+|A4.31|Pressure rise control function|(((
	2227	+0: Invalid
	2228	+
	2229	+1: Valid
	2230	+)))|0|○|0xA41F
	2231	+|(((
	2232	+
	2233	+
	2234	+A4.35
	2235	+)))|Constant frequency water shortage function selection|(((
	2236	+One place: Turn on protection
	2237	+
	2238	+0: Disable 1: Enable
	2239	+
	2240	+Tens place: Current detected
	2241	+
	2242	+0: Total current 1: Torque current
	2243	+)))|(((
	2244	+
	2245	+
	2246	+0010
	2247	+)))| |
	2248	+|A4.36|Constant frequency water shortage protection current|0% to 150%|40%| |
	2249	+|A4.37|Constant frequency water shortage protection frequency|0% to 100%|50%| |
	2250	+|A4.38|Constant frequency water shortage protection detection time|1 to 1000s|30s| |
	2251	+|A4.39|Constant frequency water shortage protection recovery time|1 to 10000s|600s| |
	2252	+|A4.40| Constant frequency water shortage protection recovery times|0 to 100|3| |
	2253	+
	2254	+
	2255	+
	2256	+6.2 Fault record parameter group
	2257	+
	2258	+|**Function code**|**Name**|**Setting range and description**|**Change**|(((
	2259	+**Modbus**
	2260	+
	2261	+**address**
	2262	+)))
	2263	+|(% colspan="5" %)**E0 Fault parameter set**
	2264	+|E0.00|Fault type|Refer to the fault Information code table for detail|◎|0xE000
	2265	+|E0.01|Failure operating frequency|0.0-Maximum frequency|◎|0xE001
	2266	+|E0.02|Fault output current|0.1-2000.0A|◎|0xE002
	2267	+|E0.03|Fault bus voltage|0-810.0V|◎|0xE003
	2268	+|E0.04|Fault input terminal status|Refer to the input terminal state diagram|◎|0xE004
	2269	+|E0.05|Fault output terminal status|Refer to the output terminal state diagram|◎|0xE005
	2270	+|E0.06|Fault module temperature|0-100℃|◎|0xE006
	2271	+|E0.07|Fault VFD condition|(((
	2272	+LED one place: Running direction
	2273	+
	2274	+0: Forward
	2275	+
	2276	+1: Reverse
	2277	+
	2278	+LED tens place: Running status
	2279	+
	2280	+0: Stop
	2281	+
	2282	+1: Steady speed
	2283	+
	2284	+2: Speed up
	2285	+
	2286	+3: Slow down
	2287	+)))|◎|0xE007
	2288	+|E0.08|(((
	2289	+Down time
	2290	+
	2291	+(Count from this power-on)
	2292	+)))|0-65535min|◎|0xE008
	2293	+|E0.09|(((
	2294	+Down time
	2295	+
	2296	+(From total running time)
	2297	+)))|0-65535H|◎|0xE009
	2298	+|E0.10|Fault output voltage|0-1500V|◎|0xE00A
	2299	+|E0.11|Fault diagnosis information|Refer to (Chapter 8 to Fault Code Details)|◎|0xE00B
	2300	+|E0.12|Number of faulty CBC|10Sec if no CBC zeroing|◎|0xE00C
	2301	+
	2302	+6.3 Display parameter group
	2303	+
	2304	+|**Function code**|**Name**|**Minimum unit**|**Change**|**Modbus address**
	2305	+|(% colspan="5" %)**D0 Display parameter group**
	2306	+|D0.00|Running frequency(Hz)|0.01Hz|◎|0xD000
	2307	+|D0.01|Setting frequency(Hz)|0.01Hz|◎|0xD001
	2308	+|D0.02|Bus voltage(V)|0.1V|◎|0xD002
	2309	+|D0.03|Output voltage(V)|1V|◎|0xD003
	2310	+|D0.04|Output current(A)|0.1A|◎|0xD004
	2311	+|D0.05|Output power(kW)|0.1kW|◎|0xD005
	2312	+|D0.06|Output torque~(%)|0.1%|◎|0xD006
	2313	+|D0.07|DI Input state| |◎|0xD007
	2314	+|D0.08|DO Output state| |◎|0xD008
	2315	+|D0.09|AI1 Voltage (V)|0.01V|◎|0xD009
	2316	+|D0.10|AI2 Voltage(V)|0.01V|◎|0xD00A
	2317	+|D0.11|AO1 Voltage(V)|0.01V|◎|0xD00B
	2318	+|D0.12|Count value| |◎|0xD00C
	2319	+|D0.13|Axis Frequency| |◎|0xD00D
	2320	+|D0.14|Load speed display|1rpm|◎|0xD00E
	2321	+|D0.15|PID setting| |◎|0xD00F
	2322	+|D0.16|PID feedback| |◎|0xD010
	2323	+|D0.17|PLC phase| |◎|0xD011
	2324	+|D0.18|PULSE input pulse frequency| |◎|0xD012
	2325	+|D0.19|Feedback speed(Unit0.1Hz)| |◎|0xD013
	2326	+|D0.20|Remaining running time| |◎|0xD014
	2327	+|D0.21|AI1Pre-correction voltage| |◎|0xD015
	2328	+|D0.22|AI2Pre-correction voltage| |◎|0xD016
	2329	+|D0.23|Reserve| |◎|0xD017
	2330	+|D0.24|Linear velocity| |◎|0xD018
	2331	+|D0.25|Current power-on time|1min|◎|0xD019
	2332	+|D0.26|Current running time|0.1min|◎|0xD01A
	2333	+|D0.27|CPU temperature| |◎|0xD01B
	2334	+|D0.28|Communication setting| |◎|0xD01C
	2335	+|D0.29|Radiator temperature| |◎|0xD01D
	2336	+|D0.30|Main frequency X display|0.01Hz|◎|0xD01E
	2337	+|D0.31|Auxiliary frequency Y display|0.01Hz|◎|0xD01F
	2338	+|D0.34|Reserve| |◎|0xD022
	2339	+|D0.35|Analog grounding| |◎|0xD023
	2340	+|D0.36|3.3VA| |◎|0xD024
	2341	+|D0.37|Control board plate number| |◎|0xD025
	2342	+|D0.38|Plate number of the power board| |◎|0xD026
	2343	+|D0.39|Power factor Angle| |◎|0xD027
	2344	+|D0.40|Virtual VDI state| |◎|0xD100
	2345	+|D0.41|Virtual VDO state| |◎|0xD101
	2346	+|D0.42|Expand DI input status| |◎|0xD102
	2347	+|D0.43|Expand DO input status| |◎|0xD103
	2348	+|D0.44|Expansion board version| |◎|0xD104
	2349	+|D0.45|AI3 (Expand) voltage (V)|0.01V|◎|0xD105
	2350	+|D0.46|AI4 (Expand) voltage (V)|0.01V|◎|0xD106
	2351	+|D0.49|AO2 Voltage (V)|0.01V|◎|0xD109
	2352	+|D0.53|Communication status of the main control board| |◎|0xD10D
	2353	+|D0.54|Extended communication status| |◎|0xD10E
	2354	+
	2355	+
	2356	+
	2357	+
	2358	+6.4 A0 Application parameter group
	2359	+
	2360	+Notes: As the software iterates, the parameter list may change.
	2361	+
	2362	+|**Function code**|**Name**|**Minimum unit**|**Change**|(((
	2363	+**Modbus**
	2364	+
	2365	+**address**
	2366	+)))
	2367	+|(% colspan="5" %)**A0 Application parameter set**
	2368	+|A0.00|Application macro|(((
	2369	+0: Default macro
	2370	+
	2371	+1: Pressure tile machinery macro
	2372	+
	2373	+2: Spring machinery macro
	2374	+
	2375	+3: Woodworking machinery macro
	2376	+)))|●|0xA000