| ... |
... |
@@ -31,65 +31,3 @@ |
| 31 |
31 |
**RS-485 2W **(RJ45 Connector): The following is the view from the soldering point of a connector. |
| 32 |
32 |
|
| 33 |
33 |
{{id name="Iimage-20220817154212-1.jpeg"/}}[[image:xwiki_PIStudio_12.PLC+protocols_WebHome_c74587d16cc7ee2.jpg||alt="image-20220817154212-1.jpeg" height="315" width="554"]] |
| 34 |
|
- |
| 35 |
|
-== **Schneider TM218 series** == |
| 36 |
|
- |
| 37 |
|
- |
| 38 |
|
-**HMI Setting** |
| 39 |
|
- |
| 40 |
|
-|=**Parameters**|=**Recommended**|=**Notes** |
| 41 |
|
-|**Protocol**|Schneider Modicon MODBUS RTU| |
| 42 |
|
-|Connection|RS485| |
| 43 |
|
-|**Baud rate**|19200| |
| 44 |
|
-|**Data bit**|8| |
| 45 |
|
-|**Parity**|Even| |
| 46 |
|
-|**Stop bit**|1| |
| 47 |
|
-|**PLC station No.**|1 |
| 48 |
|
- |
| 49 |
|
-**Device Address** |
| 50 |
|
- |
| 51 |
|
-|=**Bit/Word**|=**Device type**|=**Format**|=**Range**|=**Memo** |
| 52 |
|
-|B|IX|DDDDDo|0 ~~ 65535| |
| 53 |
|
-|B|QX|DDDDDo|0 ~~ 65535| |
| 54 |
|
-|B|MX|DDDDDDo|0 ~~ 999999| |
| 55 |
|
-|W|MW|DDDDDD|0 ~~ 999999| |
| 56 |
|
- |
| 57 |
|
- **Configure the communication protocol** |
| 58 |
|
- |
| 59 |
|
-(% style="text-align:center" %) |
| 60 |
|
-[[image:1711078502000-977.png]] |
| 61 |
|
- |
| 62 |
|
-(% style="text-align:center" %) |
| 63 |
|
-[[image:1711078509511-443.png]] |
| 64 |
|
- |
| 65 |
|
-**PLC Setting:** |
| 66 |
|
- |
| 67 |
|
-Open SoMachine Central, create a new project or open the project that has been created. |
| 68 |
|
- |
| 69 |
|
-Create new project： [Create a new project]→[Empty Project]→[OK]→[Open Configuration] |
| 70 |
|
- |
| 71 |
|
-(% style="text-align:center" %) |
| 72 |
|
-[[image:1711078656040-781.png]] |
| 73 |
|
- |
| 74 |
|
-(% style="text-align:center" %) |
| 75 |
|
-[[image:1711078662048-425.png]] |
| 76 |
|
- |
| 77 |
|
-Into the [Open Configuration].[Untitled]→[Add Device]→[Logic Controller]→[M218]→[TM218LDA16DRN] |
| 78 |
|
- |
| 79 |
|
-(% style="text-align:center" %) |
| 80 |
|
-[[image:1711078686235-785.png]] |
| 81 |
|
- |
| 82 |
|
-PLC Default Parameters:In the Devices tree [MyController]→[Serial Line 2]→[Modbus_Manager]→[Transmission Mode]:RTU→[Addressing]:Slave→[Serial Line Settings]:[Baud rate] 19200, [Data bits]8, [Stop bits]1,[Parity] EVEN,[Physical Medium] RS485 |
| 83 |
|
- |
| 84 |
|
-(% style="text-align:center" %) |
| 85 |
|
-[[image:1711078600047-723.png]] |
| 86 |
|
- |
| 87 |
|
- **Cable Wiring** |
| 88 |
|
- |
| 89 |
|
-(% style="text-align:center" %) |
| 90 |
|
-[[image:1711078719633-316.png]] |
| 91 |
|
- |
| 92 |
|
-Pin Definition Diagram： |
| 93 |
|
- |
| 94 |
|
-(% style="text-align:center" %) |
| 95 |
|
-[[image:1711078732764-435.png]] |
