Wiki source code of 1 VM Series Manual V1.2

Last modified by Mora Zhou on 2023/12/28 10:44
Show last authors
1 (% class="box infomessage" %)
2 (((
3 **This is VM series V1.2. S/N on the inverter starts from "X0".**
4 )))
5
6 = Preface =
7
8 Thank you for choosing WECON VM Series AC Drive.
9
10 This user manual introduces the technical specifications, installation instructions, functions and performance of VM Series AC Drive properly. Please read this user manual carefully before carrying out works such as installation, commissioning, maintenance, etc.
11
12 You are specially warned to read and understand safety precaution items of this manual before using this product, and to ensure that relevant electrical installation testers’ professional qualification shall be in line with the provisions of the labor supervision department, and the electrical and environmental conditions for product use shall be in conformity with relevant national standards.
13
14 Be sure to verify that the wiring is correct before powering on the product. Before starting the product, it is necessary to debug to ensure correct motor rotating direction.
15
16 = Safety precautions =
17
18 **■ Warning sign**
19
20 [[image:WECON VM 英文 V01_html_f697a083b5da7fc8.png]] DANGER: Indicates that failure to comply with the notice will result in severe personal injure or even death.
21
22 [[image:WECON VM 英文 V01_html_b36792972403c101.png]] WARNING: Indicates that failure to comply with the notice will result in moderate personal injury, property damage or equipment damage.
23
24 (% class="warning" %)|**WARNING**
25 |(((
26 ◎Do not install or operate any AC Drive that is damaged or with missing parts. Failing to follow this rule can result in facility damage or severe injury.
27
28 ◎When installing or handling the AC Drive, please hold the bottom of the product rather than the case only, to prevent its falling and being damaged.
29
30 ◎Install the AC Drive on nonflammable material like metal, and keep away from flammable or explosive object, heat source, and similar environment. Otherwise, fire may be caused.
31
32 ◎When AC Drive is installed inside an electrical cabinet or other kind of enclosure, please install fans or other cooling devices, and keep ventilation well enough to ensure the enclosure temperature below 40℃, or the AC Drive may be damaged due to extreme high temperature.
33
34 ◎Before wiring, ensure the AC Drive rated input voltage and phases are compatible with the input power source, or fire or personal injury may be caused.
35
36 ◎Never connect the AC power supply to output terminals U, V and W. Otherwise, the AC Drive will be damaged and the warranty is invalid.
37
38 ◎Never carry out withstand voltage test to the AC Drive, for example by a megohmmeter. Otherwise, it may cause damage to the AC Drive.
39
40 ◎The connecting cable of the main circuit terminal should use an insulating sleeve.
41
42 ◎When the cable length between the AC Drive and the motor exceeds 50 meters, an output reactor is recommended to be used.
43
44 ◎Do not use a circuit breaker to control the start and stop of the AC Drive. Otherwise, the AC Drive may be damaged.
45
46 ◎Since the AC Drive makes the motor running speed from low to high in a short time, please confirm that the motor and equipment are in the allowed running range before running.
47
48 ◎Do not touch due to high temperature of the heat sink and braking resistor.
49
50 ◎The factory parameters of the AC Drive can meet the requirments of most equipment operation. Under normal circumstances, please do not modify the AC Drive parameters at will. Even if there is some special applications need to change the AC Drive parameters, only necessary parameters could be changed. Otherwise, AC Drive damage may be caused.
51
52 ◎The PCB board has a CMOS integrated circuit. Do not touch it with your hands, otherwise, static electricity will damage the PCB board.
53 )))
54
55 (% class="warning" %)|**DANGER**
56 |(((
57 ◎Wiring must be completed by qualified professional electricians, otherwise, there may be electric shock or damage to the AC Drive.
58
59 ◎The power must be disconnected during wiring; otherwise, it may cause electric shock or fire.
60
61 ◎The grounding terminal should be effectively grounded; otherwise, the outer casing of the AC Drive may be energized.
62
63 ◎Do not touch the main circuit terminals, otherwise, it may cause electric shock.
64
65 ◎Terminals for brake resistor are and PB. Do not wire to other terminals, otherwise, fire may be caused.
66
67 ◎It is only allowed to power on the AC Drive after the wiring is finished and its cover is reinstalled. It is strictly prohibited to remove the cover of AC Drive while power is on. Otherwise, it may cause electric shock.
68
69 ◎Before programming the AC Drive with fault auto reset or restart option after power off, the mechanical device need to be implemented with safety protection measures first. Otherwise, personal injury will be caused.
70
71 ◎“ STOP/RESET” key may become invalid as a result of some function setting. It is recommended to install an independent emergency circuit breaker for the AC Drive control system, otherwise, or personal injury may be caused.
72
73 ◎When the power is on, there may be electricity in the AC Drive’s terminals even if it is in stop mode. Do not touch U, V, W terminals and motor connection terminals, or electrical shock may be caused.
74
75 ◎Never touch the AC Drive connection terminals when power is on. Otherwise, it may cause an electrical shock.
76
77 ◎Only qualified electricians can be authorized to do the jobs of maintenance, checking, or parts replacement.
78
79 ◎After the power supply is OFF, make sure the charge LED is OFF and the residual voltage does not exist, or wait for at least 10 minutes before carrying out maintenance or inspection. Otherwise, damage or injury may be caused.
80
81 ◎Modification to the AC Drive without permission is strictly prohibited, otherwise, severe injury may be caused. Arbitrarily modification of AC Drive will result in service warranty invalid.
82 )))
83
84 = Product information =
85
86 == Technical specifications ==
87
88 |=(% colspan="2" %)**Item**|=**Specifications**
89 |(% rowspan="7" %)Control features|Control mode|V/F control
90 |Startup torque|0.5Hz/100%
91 |Speed range|1: 50
92 |Speed stability accuracy|±1%
93 |Carrier frequency|1kHz~~6kHz；
94 |Overload capacity|60s for 150% of the rated current, 1s for 180% of the rated current.
95 |Torque boost|0.0%~~30.0%
96 |(% rowspan="4" %)Input and Output|Input voltage range|220V/380V; fluctuation range: ±15%
97 |Input frequency range|50/60Hz；fluctuation range: ±5%
98 |Output voltage range|0-input voltage; the error is less than 5%
99 |Output frequency range|0~~400Hz
100 |(% rowspan="5" %)Basic function|Running command source|Three command source：keypad; control terminals; serial communication port.
101 |Frequency source|such as digital setting, analog voltage setting, analog current setting, serial communication port setting.
102 |DC braking|(((
103 Braking time: 0.0s~~50.0s;
104
105 Braking action current value: 0.0%~~100.0%
106 )))
107 |Simple PLC/Multiple speeds|It implements up to 8 speeds via the simple PLC function or combination of DI terminal states.
108 |Protection mode|Motor short-circuit detection at power-on, input/output phase loss protection, overcurrent protection, overvoltage protection, undervoltage protection, overheat protection, overload protection and so on.
109 |(% rowspan="2" %)Display and Key operation|LED display|It displays the parameters.
110 |Parameters locking function|It can lock the parameters to prevent malfunction.
111 |(% rowspan="6" %)Environment|Installation location|Indoor, free from direct sunlight, dust, corrosive gas, combustible gas, oil smoke, vapour, drip or salt.
112 |Altitude|Lower than 1000m. When it is higher than 1000m, for every 100m, it needs to reduce power by 1%, and the maximum altitude is 3000m.
113 |Ambient temperature|-10℃~~50℃. When it is higher than 40℃, for every 1℃, it needs to reduce power by 1%, and the maximum ambient temperature is 50℃
114 |Humidity|≤95%RH, without condensing
115 |Vibration|Less than 5.9m/s2 (0.6g)
116 |Storage temperature|-25℃～+60℃
117
118 Table 1-1-1 Technical specification shee
119
120 == Product nameplate ==
121
122 (% style="text-align:center" %)
123 (((
124 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
125 [[Figure 1-2-1 Product nameplate>>image:WECON VM 英文 V01_html_5a52ff18546c8417.png||id="IWECONVMA082F16587A0V01_html_5a52ff18546c8417.png"]]
126 )))
127
128
129 == Model description ==
130
131 __VM__ – __2__ __S__ __1R5GB__
132
133 ①  ② ③  ④
134
135 |=**Field**|=**No.**|=**Identification**|=**Description**
136 |Product series|①|Product series|VM series
137 |Voltage grade|②|Voltage grade|2: 220VAC; 4: 380VAC
138 |The input power|③|Power phase identification|S: single; T: three-phase
139 |Rated power|④|Power range|1R5-1.5kW，R is the decimal point
140
141 Table 1-3-1 VM series model field comment
142
143 == Product model ==
144
145 |=(% rowspan="2" scope="row" %)AC Drive Model|=Rated power|=Power capacity|=Input current|=(% style="width: 173px;" %)Output current|=(% colspan="2" style="width: 199px;" %)Motor G/P
146 |=kW|=kVA|=A|=(% style="width: 173px;" %)A|=(% style="width: 128px;" %)kW|=HP
147 |=VM-2SR75|0.75|1.5|8.2|(% style="width:173px" %)4|(% style="width:128px" %)0.75|1
148 |=VM-2S1R5|1.5|3|14.2|(% style="width:173px" %)7|(% style="width:128px" %)1.5|2
149 |=VM-2S2R2|2.2|4|23|(% style="width:173px" %)9.6|(% style="width:128px" %)2.2|3
150 |=VM-4T2R2|2.2|4|5.8|(% style="width:173px" %)5.1|(% style="width:128px" %)2.2|3
151 |=VM-4T004|4|5.9|10.5|(% style="width:173px" %)9|(% style="width:128px" %)4/|5.5
152 |=VM-4T5R5|5.5|8.9|14.6|(% style="width:173px" %)13|(% style="width:128px" %)5.5|7.5
153 |=VM-4T7R5|7.5|11|20.5|(% style="width:173px" %)17|(% style="width:128px" %)7.5|10
154 |=VM-4T011*|11|17|26|(% style="width:173px" %)25|(% style="width:128px" %)11|15
155 |=VM-4T015*|15|21|35|(% style="width:173px" %)32|(% style="width:128px" %)15|20
156
157 Table 1-4-1 Product model table
158
159 (% class="box infomessage" %)
160 (((
161 *:In development
162 )))
163
164 = Installation =
165
166 == Overall structural drawing ==
167
168 (% class="wikigeneratedid" %)
169 unit: mm
170
171 (% style="text-align:center" %)
172 (((
173 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
174 [[Figure 2-1-1 Outline dimension diagram>>image:1624240220324-243.png||id="I1624240220324-243.png"]]
175 )))
176
177
178 (% style="width:1271.22px" %)
179 |=(% rowspan="2" scope="row" style="width: 267px;" %)AC Drive Model|=(% colspan="3" style="width: 384px;" %)Overall Dimensions|=(% colspan="2" style="width: 294px;" %)Mounting Hole|=(% style="width: 259px;" %)Mounting Hole Diameter
180 |=(% style="width: 118px;" %)H|=(% style="width: 120px;" %)W|=(% style="width: 145px;" %)D|=(% style="width: 147px;" %)H1|=(% style="width: 147px;" %)W1|=(% style="width: 259px;" %)d
181 |=(% style="width: 267px;" %)VM-2SR75|(% rowspan="2" style="width:118px" %)134|(% rowspan="2" style="width:120px" %)69|(% rowspan="2" style="width:145px" %)104|(% rowspan="2" style="width:147px" %)123|(% rowspan="2" style="width:147px" %)55|(% rowspan="2" style="width:259px" %)5
182 |=(% style="width: 267px;" %)VM-2S1R5
183 |=(% style="width: 267px;" %)VM-2S2R2|(% rowspan="2" style="width:118px" %)142|(% rowspan="2" style="width:120px" %)72|(% rowspan="2" style="width:145px" %)116|(% rowspan="2" style="width:147px" %)130|(% rowspan="2" style="width:147px" %)59|(% rowspan="2" style="width:259px" %)5
184 |=(% style="width: 267px;" %)VM-4T2R2
185 |=(% style="width: 267px;" %)VM-4T004|(% style="width:118px" %)196|(% style="width:120px" %)95|(% style="width:145px" %)132|(% style="width:147px" %)179|(% style="width:147px" %)79|(% style="width:259px" %)5.5
186 |=(% style="width: 267px;" %)VM-4T5R5|(% rowspan="2" style="width:118px" %)225|(% rowspan="2" style="width:120px" %)115|(% rowspan="2" style="width:145px" %)154|(% rowspan="2" style="width:147px" %)208|(% rowspan="2" style="width:147px" %)99|(% rowspan="2" style="width:259px" %)5.5
187 |=(% style="width: 267px;" %)VM-4T7R5
188 |=(% style="width: 267px;" %)VM-4T011|(% style="width:118px" %)-|(% style="width:120px" %)-|(% style="width:145px" %)-|(% style="width:147px" %)-|(% style="width:147px" %)-|(% style="width:259px" %)-
189 |=(% style="width: 267px;" %)VM-4T015|(% style="width:118px" %)-|(% style="width:120px" %)-|(% style="width:145px" %)-|(% style="width:147px" %)-|(% style="width:147px" %)-|(% style="width:259px" %)-
190
191 Table 2-1-1 outline dimension
192
193 == Terminal connection ==
194
195 (% style="text-align:center" %)
196 (((
197 (% class="wikigeneratedid img-thumbnail" style="display:inline-block" %)
198 [[Figure 2-2-1 Terminal connection>>image:1624240272484-903.png||id="I1624240272484-903.png"]]
199 )))
200
201
202 **Main circuit connection**
203
204 |=(% scope="row" %)**Terminal mark**|=**Name**|=**Description**
205 |=R、S、T|Power supply input terminals|Connect to the AC power supply
206 |=U、V、W|AC drive output terminals|Connect the three-phase motor.
207 |=[[image:WECON VM 英文 V01_html_2b5dc89a424d22e6.png||height="22" width="23"]]|Grounding terminal|Must be grounded.
208
209 Table 2-2-1 Main circuit terminals and function
210
211 **Control circuit connection**
212
213 |=**Category**|=**Terminal symbol**|=**Terminal name**|=**Function description**
214 |(% rowspan="2" %)Power supply|+10V-GND|＋10V power supply|(((
215 Provide +10V power supply to external unit.
216
217 Maximum output current: 20 mA.
218 )))
219 |+24V-COM|＋24V power supply|Provide +24V power supply to external unit.
220 |Analog input|AI-GND|Analog input terminal 1|Input voltage range: 0-10V
221 |(% rowspan="4" %)Digital input|DI1|Digital input 1|(% rowspan="4" %)
222 |DI2|Digital input 2
223 |DI3|Digital input 3
224 |DI4|Digital input 4
225 |Relay output|RA-RC|NO terminal|NO terminal
226 |(% colspan="2" rowspan="2" %)Communication port and socket|S+|RS485 signal positive terminal
227 |S-|RS485 signal negative terminal
228
229 Table 2-2-2 Control terminal instruction
230
231 = Display and operation =
232
233 == Keypad ==
234
235 You can modify the parameters, monitor the working status and start or stop the AC Drive by operating the keypad, as shown in the following figure.
236
237 (% style="text-align:center" %)
238 (((
239 (% class="wikigeneratedid img-thumbnail" style="display:inline-block; width:280px;" %)
240 [[Figure 3-1-1 Keypad diagram>>image:WECON VM 英文 V01_html_53c6de9f2105008c.png||height="302" id="IWECONVMA082F16587A0V01_html_53c6de9f2105008c.png" width="280"]]
241 )))
242
243
244 == Description of indicators and keys ==
245
246 |=(% scope="row" %)**Item**|=(% style="width: 213px;" %)**Name**|=(% style="width: 865px;" %)**Function**
247 |=Indicator|(% style="width:213px" %)Status|(% style="width:865px" %)(((
248 * RUN: ON/Running; OFF/Stop.
249 * REMOTE: ON/Terminal control; Blinking/Communication; OFF/keypad control.
250 * FWD/REV: ON/Forward rotation; OFF/Reverse rotation; Blinking/Forward and reverse switching.
251 * ALARM: Blinking /Fault state.
252 )))
253 |=(% rowspan="6" %)Keys|(% style="width:213px" %)(((
254 PRG (Programming)
255 )))|(% style="width:865px" %)Enter or exit the first menu.
256 |(% scope="row" style="width:213px" %)ENT (Confirm)|(% style="width:865px" %)Enter the menu interfaces and confirm the parameter setting.
257 |(% scope="row" style="width:213px" %)△（Increment）|(% style="width:865px" %)Increase date or function code.
258 |(% scope="row" style="width:213px" %)▽（Decrement）|(% style="width:865px" %)Decrease data or function code.
259 |(% scope="row" style="width:213px" %)<<（Shift）|(% style="width:865px" %)Select the displayed parameters in the stop or running state and select the digit to be modified when modifying parameters.
260 |(% scope="row" style="width:213px" %)RUN/STOP|(% style="width:865px" %)(((
261 Control drive start and stop in keypad control mode.
262
263 Perform the reset operation when it is in the fault state.
264 )))
265 |=Potentiometer|(% style="width:213px" %)Resistance potentiometer|(% style="width:865px" %)Frequency adjustment in keyboard operation mode
266
267 Table 3-2-1 Description of Indicators and key
268
269 = Parameter function =
270
271 * “○”: the parameter can be modified in both standby and operating state；
272 * “●”: the parameter can’t be modified in operating state；
273 * “◎”:the parameter is the actual detected and recorded value which can’t be modified；
274
275 (% class="box infomessage" %)
276 (((
277 **Note: **the communication address is hexadecimal.
278 )))
279
280 == Functional parameter ==
281
282 |=(% scope="row" style="width: 97px;" %)Parameter|=(% style="width: 320px;" %)Name|=(% style="width: 428px;" %)Setting Range|=(% style="width: 190px;" %)Default|=(% style="width: 80px;" %)Property|=(% style="width: 87px;" %)Address
283 |=(% style="width: 97px;" %)F0.00|(% style="width:320px" %)Reserved|(% style="width:428px" %)Reserved|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0000
284 |=(% style="width: 97px;" %)F0.01|(% style="width:320px" %)Command source selection|(% style="width:428px" %)(((
285 * 0：Operation panel control（LED off）
286 * 1：Terminal control（LED on）
287 * 2：Communication LED (LED blinking）
288 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0001
289 |=(% style="width: 97px;" %)F0.02|(% style="width:320px" %)Setting main frequency source X|(% style="width:428px" %)(((
290 * 0：Digital setting (non-retentive at power failure)
291 * 1：Digital setting (retentive at power failure)
292 * 2：Keypad Knob
293 * 3：AI
294 * 4：Multi-stage speed
295 * 5：Simple PLC
296 * 6：Communication
297 )))|(% style="width:190px" %)2|(% style="width:80px" %)●|(% style="width:87px" %)0002
298 |=(% style="width: 97px;" %)F0.03|(% style="width:320px" %)Keypad setting frequency|(% style="width:428px" %)0.00Hz～F0.05|(% style="width:190px" %)50.0Hz|(% style="width:80px" %)○|(% style="width:87px" %)0003
299 |=(% style="width: 97px;" %)F0.04|(% style="width:320px" %)Running direction selection|(% style="width:428px" %)(((
300 * 0：Forward
301 * 1：Reverse
302 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0004
303 |=(% style="width: 97px;" %)F0.05|(% style="width:320px" %)Maximum Output Frequency|(% style="width:428px" %)50.00Hz～400.00Hz|(% style="width:190px" %)50.0Hz|(% style="width:80px" %)●|(% style="width:87px" %)0005
304 |=(% style="width: 97px;" %)F0.06|(% style="width:320px" %)Upper Limit of Frequency|(% style="width:428px" %)F0.07～F0.05|(% style="width:190px" %)50.0Hz|(% style="width:80px" %)○|(% style="width:87px" %)0006
305 |=(% style="width: 97px;" %)F0.07|(% style="width:320px" %)Lower Limit of Frequency|(% style="width:428px" %)0.00Hz～F0.06|(% style="width:190px" %)0.0Hz|(% style="width:80px" %)○|(% style="width:87px" %)0007
306 |=(% style="width: 97px;" %)F0.08|(% style="width:320px" %)The option of frequency lower limit|(% style="width:428px" %)(((
307 * 0：Running at frequency lower limit
308 * 1：Stop
309 * 2：Standby
310 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0008
311 |=(% style="width: 97px;" %)F0.09|(% style="width:320px" %)Carrier Frequency|(% style="width:428px" %)1kHz～6.0kHz|(% style="width:190px" %)6.0kHz|(% style="width:80px" %)●|(% style="width:87px" %)0009
312 |=(% style="width: 97px;" %)F0.10|(% style="width:320px" %)Acceleration Time 1|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)10.0s|(% style="width:80px" %)○|(% style="width:87px" %)000A
313 |=(% style="width: 97px;" %)F0.11|(% style="width:320px" %)Deceleration Time 1|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)10.0s|(% style="width:80px" %)○|(% style="width:87px" %)000B
314 |=(% style="width: 97px;" %)F0.12|(% style="width:320px" %)Stop Mode|(% style="width:428px" %)(((
315 * 0：Decelerate to stop
316 * 1：Free stop
317 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)000C
318 |=(% style="width: 97px;" %)F0.13|(% style="width:320px" %)Retentive of digital setting frequency|(% style="width:428px" %)(((
319 * 0：No retentive
320 * 1：retentive
321 )))|(% style="width:190px" %)1|(% style="width:80px" %)●|(% style="width:87px" %)000D
322 |=(% style="width: 97px;" %)F0.14|(% style="width:320px" %)Fan operating mode|(% style="width:428px" %)(((
323 * 0：Run when motor is running
324 * 1：Keep run when power on
325 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)000E
326 |=(% style="width: 97px;" %)F0.15|(% style="width:320px" %)AI1 Input Option|(% style="width:428px" %)(((
327 * 0: 0-10V
328 * 1: 4-20mA
329 * 2: 0-20mA
330 * 3: 0-5V
331 * 4: 0.5-4.5V
332 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)000F
333 |=(% style="width: 97px;" %)F1.00|(% style="width:320px" %)Default Setting Restoring|(% style="width:428px" %)(((
334 * 0: No Operation
335 * 1: Restore to factory default setting (not including F2 parameters)
336 * 2: Clear error records
337 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0100
338 |=(% style="width: 97px;" %)F1.01|(% style="width:320px" %)Parameters Lockup|(% style="width:428px" %)(((
339 * 0: Invalid
340 * 1: Valid
341 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0101
342 |=(% style="width: 97px;" %)F1.02|(% style="width:320px" %)User Password|(% style="width:428px" %)0~~65000|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0102
343 |=(% style="width: 97px;" %)F2.00|(% style="width:320px" %)Motor Rated Power|(% style="width:428px" %)0.1kW~~2.2kW|(% style="width:190px" %)Determined by Drive Model|(% style="width:80px" %)●|(% style="width:87px" %)0200
344 |=(% style="width: 97px;" %)F2.01|(% style="width:320px" %)Motor Rated Voltage|(% style="width:428px" %)0~~380V|(% style="width:190px" %)Determined by Drive Model|(% style="width:80px" %)●|(% style="width:87px" %)0201
345 |=(% style="width: 97px;" %)F2.02|(% style="width:320px" %)Motor Rated Frequency|(% style="width:428px" %)0~~ F0.05|(% style="width:190px" %)Determined by Drive Model|(% style="width:80px" %)●|(% style="width:87px" %)0202
346 |=(% style="width: 97px;" %)F2.03|(% style="width:320px" %)Motor Rated Current|(% style="width:428px" %)1.00~~10.00|(% style="width:190px" %)Determined by Drive Model|(% style="width:80px" %)●|(% style="width:87px" %)0203
347 |=(% style="width: 97px;" %)F2.05|(% style="width:320px" %)Type of Motor|(% style="width:428px" %)(((
348 * 0: Three Phase
349 * 1: Single Phase
350 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0205
351 |=(% style="width: 97px;" %)F2.06|(% style="width:320px" %)Single-phase motor main and auxiliary winding turns ratio|(% style="width:428px" %)10~~200|(% style="width:190px" %)80|(% style="width:80px" %)○|(% style="width:87px" %)0206
352 |=(% style="width: 97px;" %)F2.07|(% style="width:320px" %)Single-phase motor current correction factor|(% style="width:428px" %)50~~200|(% style="width:190px" %)130|(% style="width:80px" %)○|(% style="width:87px" %)0207
353 |=(% style="width: 97px;" %)F4.00|(% style="width:320px" %)Torque Boost|(% style="width:428px" %)0.0%~~30.0%|(% style="width:190px" %)4.0%|(% style="width:80px" %)○|(% style="width:87px" %)0400
354 |=(% style="width: 97px;" %)F4.01|(% style="width:320px" %)Cut-off frequency of torque boost|(% style="width:428px" %)0.00Hz～F0.05|(% style="width:190px" %)50.00Hz|(% style="width:80px" %)●|(% style="width:87px" %)0401
355 |=(% style="width: 97px;" %)F4.02|(% style="width:320px" %)Trigging frequency of DC braking at stop|(% style="width:428px" %)0.00Hz～F0.05|(% style="width:190px" %)0.00Hz|(% style="width:80px" %)○|(% style="width:87px" %)0402
356 |=(% style="width: 97px;" %)F4.03|(% style="width:320px" %)Delay time of DC braking at stop|(% style="width:428px" %)0.0s～50.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)0403
357 |=(% style="width: 97px;" %)F4.04|(% style="width:320px" %)The current of DC braking at stop|(% style="width:428px" %)0～100%|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0404
358 |=(% style="width: 97px;" %)F4.05|(% style="width:320px" %)The time of DC braking at stop|(% style="width:428px" %)0.0s～50.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)0405
359 |=(% style="width: 97px;" %)F4.06|(% style="width:320px" %)Automatic adjustment of carrier Frequency|(% style="width:428px" %)(((
360 * 0: Invalid;
361 * 1: Valid
362 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0406
363 |=(% style="width: 97px;" %)F4.07|(% style="width:320px" %)0 frequency output option|(% style="width:428px" %)(((
364 * 0: Valid;
365 * 1: Invalid
366 )))|(% style="width:190px" %)1|(% style="width:80px" %)●|(% style="width:87px" %)0407
367 |=(% style="width: 97px;" %)F5.00|(% style="width:320px" %)DI1 terminal function selection|(% rowspan="4" style="width:428px" %)(((
368 * 0: No function
369 * 1: Forward running (FWD)
370 * 2: Reverse running (REV)
371 * 3: Three-wire operation control
372 * 4: Forward point movement (FJOG)
373 * 5: Reverse point movement (RJOG)
374 * 6: Error Reset
375 * 7: Terminal UP
376 * 8: Terminal Down
377 * 9: UP/DOWN Setting Clear
378 * 10: External error input(Normally Open)
379 * 11: PLC Status reset
380 * 12: Multi stage speed terminal 1
381 * 13: Multi stage speed terminal 2
382 * 14: Reserved
383 )))|(% style="width:190px" %)1|(% style="width:80px" %)●|(% style="width:87px" %)0500
384 |=(% style="width: 97px;" %)F5.01|(% style="width:320px" %)DI2 terminal function selection|(% style="width:190px" %)2|(% style="width:80px" %)●|(% style="width:87px" %)0501
385 |=(% style="width: 97px;" %)F5.02|(% style="width:320px" %)DI3 terminal function selection|(% style="width:190px" %)6|(% style="width:80px" %)●|(% style="width:87px" %)0502
386 |=(% style="width: 97px;" %)F5.03|(% style="width:320px" %)DI4 terminal function selection|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0503
387 |=(% style="width: 97px;" %)F5.04|(% style="width:320px" %)DI filter time|(% style="width:428px" %)0.000s～1.000s|(% style="width:190px" %)0.010s|(% style="width:80px" %)○|(% style="width:87px" %)0504
388 |=(% style="width: 97px;" %)F5.05|(% style="width:320px" %)Terminal Command Option|(% style="width:428px" %)(((
389 * 0: Two-line mode 1
390 * 1: Two-line mode 2
391 * 2: Three-line mode 1
392 * 3: Three-line mode 2
393 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0505
394 |=(% style="width: 97px;" %)F5.06|(% style="width:320px" %)UP/DOWN change rate range|(% style="width:428px" %)0.01Hz～50.00Hz|(% style="width:190px" %)0.50Hz|(% style="width:80px" %)○|(% style="width:87px" %)0506
395 |=(% style="width: 97px;" %)F5.07|(% style="width:320px" %)AI minimum input|(% style="width:428px" %)0.00V～F5.09|(% style="width:190px" %)0.00V|(% style="width:80px" %)○|(% style="width:87px" %)0507
396 |=(% style="width: 97px;" %)F5.08|(% style="width:320px" %)Percentage rate of AI minimum input|(% style="width:428px" %)-100.0%～+100.0%|(% style="width:190px" %)0.0%|(% style="width:80px" %)○|(% style="width:87px" %)0508
397 |=(% style="width: 97px;" %)F5.09|(% style="width:320px" %)AI maximum input|(% style="width:428px" %)F5.07～+10.00V|(% style="width:190px" %)10.00V|(% style="width:80px" %)○|(% style="width:87px" %)0509
398 |=(% style="width: 97px;" %)F5.10|(% style="width:320px" %)Percentage rate of AI maximum input|(% style="width:428px" %)-100.0%～+100.0%|(% style="width:190px" %)100.0%|(% style="width:80px" %)○|(% style="width:87px" %)050A
399 |=(% style="width: 97px;" %)F5.11|(% style="width:320px" %)AI filter time|(% style="width:428px" %)0.00s～10.00s|(% style="width:190px" %)0.10s|(% style="width:80px" %)○|(% style="width:87px" %)050B
400 |=(% style="width: 97px;" %)F5.12|(% style="width:320px" %)DI1 Enable Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)050C
401 |=(% style="width: 97px;" %)F5.13|(% style="width:320px" %)DI2 Enable Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)050D
402 |=(% style="width: 97px;" %)F5.14|(% style="width:320px" %)DI1 Disable Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)050E
403 |=(% style="width: 97px;" %)F5.15|(% style="width:320px" %)DI2 Disable Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)050F
404 |=(% style="width: 97px;" %)F5.16|(% style="width:320px" %)AI Input Digital Functional Option|(% style="width:428px" %)(((
405 * 0: No function
406 * 1: Forward running (FWD)
407 * 2: Reverse running (REV)
408 * 3: Three-wire operation control
409 * 4: Forward point movement (FJOG)
410 * 5: Reverse point movement (RJOG)
411 * 6: Error Reset
412 * 7: Terminal UP
413 * 8: Terminal Down
414 * 9: UP/DOWN Setting Clear
415 * 10: External error input(Normally Open)
416 * 11: PLC Status reset
417 * 12: Multi stage speed terminal 1
418 * 13: Multi stage speed terminal 2
419 * 14: Reserved
420 )))|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0510
421 |=(% style="width: 97px;" %)F5.17|(% style="width:320px" %)AI Input Valid Level Option|(% style="width:428px" %)(((
422 * 0: Low Level Valid
423 * 1: High Level Valid
424 )))|(% style="width:190px" %)1|(% style="width:80px" %)○|(% style="width:87px" %)0511
425 |=(% style="width: 97px;" %)F6.00|(% style="width:320px" %)Relay Output Option|(% style="width:428px" %)(((
426 * 0: No Output
427 * 1: VFD Running
428 * 2: Error Output(Output is valid only after VFD stops)
429 * 3: Ready for Running
430 * 4: Communication Setting
431 * 5: User Defined Output
432 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0600
433 |=(% style="width: 97px;" %)F6.01|(% style="width:320px" %)Relay1 Closed Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)0601
434 |=(% style="width: 97px;" %)F6.02|(% style="width:320px" %)Relay1 Open Delay Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)0602
435 |=(% style="width: 97px;" %)F6.03|(% style="width:320px" %)(((
436 User defined output
437
438 Variability option（EX）
439 )))|(% style="width:428px" %)(((
440 * 0: Running Frequency
441 * 1: Set Frequency
442 * 2: Bus Voltage
443 * 3: Output Voltage
444 * 4: Output Current
445 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0603
446 |=(% style="width: 97px;" %)F6.04|(% style="width:320px" %)User defined comparison method|(% style="width:428px" %)Units digit：comparison test method(((
447 * 0: Equal (EX==X1)
448 * 1: Equal or greater than
449 * 2: Equal or less than
450 * 3: Interval comparison (X1≤EX≤X2)
451 * 4: Units digit test (EX&X1=X2)
452
453 Tens digit: output method
454
455 * 0: False value output
456 * 1: Real value output
457 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0604
458 |=(% style="width: 97px;" %)F6.05|(% style="width:320px" %)User defined output dead zone|(% style="width:428px" %)0～65535|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0605
459 |=(% style="width: 97px;" %)F6.06|(% style="width:320px" %)(((
460 User-defined output
461
462 comparison value 1
463 )))|(% style="width:428px" %)0～65535|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0606
464 |=(% style="width: 97px;" %)F6.07|(% style="width:320px" %)(((
465 User-defined output
466
467 comparison value 2
468 )))|(% style="width:428px" %)0～65535|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0607
469 |=(% style="width: 97px;" %)F6.08|(% style="width:320px" %)AO1 Output Option|(% rowspan="2" style="width:428px" %)(((
470 * 0: Running Frequency（0～F0.05）
471 * 1: Set Frequency（0～F0.05）
472 * 2: Output Current（0～Double Rated Current of VFD）
473 * 3: Output Voltage（0～1.2times of VFD Rated Output Voltage）
474 * 4: AI（0～10V）
475 * 5: Bus Voltage（0～500.0/1000.0V）
476 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0608
477 |=(% style="width: 97px;" %)F6.09|(% style="width:320px" %)AO2 Output Option|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0609
478 |=(% style="width: 97px;" %)F6.10|(% style="width:320px" %)AO1 offset coefficient|(% style="width:428px" %)-100.0%～+100.0%|(% style="width:190px" %)0.0%|(% style="width:80px" %)○|(% style="width:87px" %)060A
479 |=(% style="width: 97px;" %)F6.11|(% style="width:320px" %)AO1 gain|(% style="width:428px" %)-10.00～+10.00|(% style="width:190px" %)1.00|(% style="width:80px" %)○|(% style="width:87px" %)060B
480 |=(% style="width: 97px;" %)F6.12|(% style="width:320px" %)AO2 offset coefficient|(% style="width:428px" %)-100.0%～+100.0%|(% style="width:190px" %)0.0%|(% style="width:80px" %)○|(% style="width:87px" %)060C
481 |=(% style="width: 97px;" %)F6.13|(% style="width:320px" %)AO2 offset coefficient|(% style="width:428px" %)-10.00～+10.00|(% style="width:190px" %)1.00|(% style="width:80px" %)○|(% style="width:87px" %)060D
482 |=(% style="width: 97px;" %)F7.00|(% style="width:320px" %)Reserved|(% style="width:428px" %)Reserved|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0700
483 |=(% style="width: 97px;" %)F7.01|(% style="width:320px" %)STOP Button Function|(% style="width:428px" %)(((
484 * 0: Valid only at keypad control mode
485 * 1: Valid at all control modes
486 )))|(% style="width:190px" %)1|(% style="width:80px" %)○|(% style="width:87px" %)0701
487 |=(% style="width: 97px;" %)F7.02|(% style="width:320px" %)LED display parameters at running status|(% rowspan="2" style="width:428px" %)(((
488 * Bit0: Running Frequency(Hz)
489 * Bit1: Set Frequency(Hz)
490 * Bit2: Bus Voltage(V)
491 * Bit3: Output Voltage(V)
492 * Bit4: Output Current(A)
493 * Bit5: DI Input Status
494 * Bit6: DO Output Status
495 * Bit7: Keypad Knob Voltage(V)
496 * Bit8: AIVoltage(V)
497 * Bit9: Load Speed
498 * Bit10: PID Set Value
499 * Bit11: PID Feedback Value
500 * Bit12: PLC Stage
501 * Bit13: Feedback Frequency（Unit：0.1Hz)
502 * Bit14: Communication Set Value
503 * Bit15: Main Frequency Source X
504 )))|(% style="width:190px" %)0x1F|(% style="width:80px" %)○|(% style="width:87px" %)0702
505 |=(% style="width: 97px;" %)F7.03|(% style="width:320px" %)LED display parameters at stop status|(% style="width:190px" %)0x06|(% style="width:80px" %)○|(% style="width:87px" %)0703
506 |=(% style="width: 97px;" %)F7.04|(% style="width:320px" %)Load speed display coefficient|(% style="width:428px" %)0.0001～6.5000|(% style="width:190px" %)3.000|(% style="width:80px" %)○|(% style="width:87px" %)0704
507 |=(% style="width: 97px;" %)F7.05|(% style="width:320px" %)Software Version|(% style="width:428px" %)-|(% style="width:190px" %)-|(% style="width:80px" %)◎|(% style="width:87px" %)0705
508 |=(% style="width: 97px;" %)F8.00|(% style="width:320px" %)Jog Running Frequency|(% style="width:428px" %)0.00Hz～F0.05|(% style="width:190px" %)2.00Hz|(% style="width:80px" %)○|(% style="width:87px" %)0800
509 |=(% style="width: 97px;" %)F8.01|(% style="width:320px" %)Jog Acceleration Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)10.0s|(% style="width:80px" %)○|(% style="width:87px" %)0801
510 |=(% style="width: 97px;" %)F8.02|(% style="width:320px" %)Jog Deceleration Time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)10.0s|(% style="width:80px" %)○|(% style="width:87px" %)0802
511 |=(% style="width: 97px;" %)F8.03|(% style="width:320px" %)FWD/REV dead zone time|(% style="width:428px" %)0.0s～100.0s|(% style="width:190px" %)0.0s|(% style="width:80px" %)○|(% style="width:87px" %)0803
512 |=(% style="width: 97px;" %)F8.04|(% style="width:320px" %)Reverse control|(% style="width:428px" %)(((
513 * 0: valid
514 * 1: invalid
515 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0804
516 |=(% style="width: 97px;" %)F8.05|(% style="width:320px" %)Reserved|(% style="width:428px" %)0|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0805
517 |=(% style="width: 97px;" %)F8.06|(% style="width:320px" %)Startup Protection Option|(% style="width:428px" %)(((
518 * 0：Invalid
519 * 1：Valid
520 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0806
521 |=(% style="width: 97px;" %)F8.07|(% style="width:320px" %)Terminal jogging priority|(% style="width:428px" %)(((
522 * 0: Invalid
523 * 1: Valid
524 )))|(% style="width:190px" %)1|(% style="width:80px" %)○|(% style="width:87px" %)0807
525 |=(% style="width: 97px;" %)FC.00|(% style="width:320px" %)Local Addresse|(% style="width:428px" %)1～30，0 for broadcast addresse|(% style="width:190px" %)1|(% style="width:80px" %)○|(% style="width:87px" %)0C00
526 |=(% style="width: 97px;" %)FC.01|(% style="width:320px" %)Baud Rate|(% style="width:428px" %)(((
527 * 0: 4800bPS
528 * 1: 9600bPS
529 * 2: 19200bPS
530 )))|(% style="width:190px" %)1|(% style="width:80px" %)○|(% style="width:87px" %)0C01
531 |=(% style="width: 97px;" %)FC.02|(% style="width:320px" %)Data format|(% style="width:428px" %)(((
532 * 0: No check, data format (8.N.1)
533 * 1: Odd Parity check, data format (8.O.1)
534 * 2: Even parity check, data format (8.E.1)
535 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0C02
536 |=(% style="width: 97px;" %)FC.03|(% style="width:320px" %)Respond Delay|(% style="width:428px" %)0ms～20ms|(% style="width:190px" %)2|(% style="width:80px" %)○|(% style="width:87px" %)0C03
537 |=(% style="width: 97px;" %)FC.04|(% style="width:320px" %)Reserved|(% style="width:428px" %)0|(% style="width:190px" %)0|(% style="width:80px" %)●|(% style="width:87px" %)0C04
538 |=(% style="width: 97px;" %)FD.00|(% style="width:320px" %)Multistage speed 0|(% style="width:428px" %)-100.0%～100.0%(100.0% as F0.05)|(% style="width:190px" %)0.00%|(% style="width:80px" %)○|(% style="width:87px" %)0D00
539 |=(% style="width: 97px;" %)FD.01|(% style="width:320px" %)Multistage speed 1|(% style="width:428px" %)-100.0%～100.0%|(% style="width:190px" %)0.00%|(% style="width:80px" %)○|(% style="width:87px" %)0D01
540 |=(% style="width: 97px;" %)FD.02|(% style="width:320px" %)Multistage speed 2|(% style="width:428px" %)-100.0%～100.0%|(% style="width:190px" %)0.00%|(% style="width:80px" %)○|(% style="width:87px" %)0D02
541 |=(% style="width: 97px;" %)FD.03|(% style="width:320px" %)Multistage speed 3|(% style="width:428px" %)-100.0%～100.0%|(% style="width:190px" %)0.00%|(% style="width:80px" %)○|(% style="width:87px" %)0D03
542 |=(% style="width: 97px;" %)FD.04|(% style="width:320px" %)Simple PLC running mode|(% style="width:428px" %)(((
543 * 0: Stop after the AC Drive runs one cycle
544 * 1: Keep final values after the AC Drive runs one cycle
545 * 2: Repeat after the AC Drive runs one cycle
546 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D04
547 |=(% style="width: 97px;" %)FD.05|(% style="width:320px" %)Simple PLC retentive option|(% style="width:428px" %)Units Digit: Reserved
548 Tens Digit：(((
549 * 0: Invalid
550 * 1: Valid
551 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D05
552 |=(% style="width: 97px;" %)FD.06|(% style="width:320px" %)Running time of simple PLC reference 0|(% style="width:428px" %)0.0s(h)～100.0s(h)|(% style="width:190px" %)0.0s(h)|(% style="width:80px" %)○|(% style="width:87px" %)0D06
553 |=(% style="width: 97px;" %)FD.07|(% style="width:320px" %)Acceleration/deceleration time of simple PLC reference 0|(% style="width:428px" %)0～3|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D07
554 |=(% style="width: 97px;" %)FD.08|(% style="width:320px" %)Running time of simple PLC reference 1|(% style="width:428px" %)0.0～100.0|(% style="width:190px" %)0.0s(h)|(% style="width:80px" %)○|(% style="width:87px" %)0D08
555 |=(% style="width: 97px;" %)FD.09|(% style="width:320px" %)Acceleration/deceleration time of simple PLC reference 1|(% style="width:428px" %)0~~3|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D09
556 |=(% style="width: 97px;" %)FD.10|(% style="width:320px" %)Running time of simple PLC reference 2|(% style="width:428px" %)0.0 ~~100.0|(% style="width:190px" %)0.0s(h)|(% style="width:80px" %)○|(% style="width:87px" %)0D0A
557 |=(% style="width: 97px;" %)FD.11|(% style="width:320px" %)Acceleration/deceleration time of simple PLC reference 2|(% style="width:428px" %)0~~3|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D0B
558 |=(% style="width: 97px;" %)FD.12|(% style="width:320px" %)Running time of simple PLC reference 3|(% style="width:428px" %)0.0~~100.0|(% style="width:190px" %)0.0s(h)|(% style="width:80px" %)○|(% style="width:87px" %)0D0C
559 |=(% style="width: 97px;" %)FD.13|(% style="width:320px" %)Acceleration/deceleration time of simple PLC reference 3|(% style="width:428px" %)0~~3|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D0D
560 |=(% style="width: 97px;" %)FD.14|(% style="width:320px" %)Time unit of simple PLC running|(% style="width:428px" %)(((
561 * 0: s（second）
562 * 1: h（hour）
563 * 2: min（minute）
564 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D0E
565 |=(% style="width: 97px;" %)FD.15|(% style="width:320px" %)The source of multistage speed 0|(% style="width:428px" %)(((
566 * 0: Set by FD.00
567 * 1: AI
568 )))|(% style="width:190px" %)0|(% style="width:80px" %)○|(% style="width:87px" %)0D0F
569
570 == Monitoring Parameters ==
571
572 |=(% scope="row" %)Parameter|=Name|=(% style="width: 257px;" %)Minimum Unit|=(% style="width: 160px;" %)Priority|=(% style="width: 113px;" %)Address
573 |=D0.00|Running Frequency(Hz)|(% style="width:257px" %)0.01Hz|(% style="width:160px" %)◎|(% style="width:113px" %)D000
574 |=D0.01|Set Frequency(Hz)|(% style="width:257px" %)0.01Hz|(% style="width:160px" %)◎|(% style="width:113px" %)D001
575 |=D0.02|Bus Voltage(V)|(% style="width:257px" %)0.1V|(% style="width:160px" %)◎|(% style="width:113px" %)D002
576 |=D0.03|Output Voltage(V)|(% style="width:257px" %)1V|(% style="width:160px" %)◎|(% style="width:113px" %)D003
577 |=D0.04|Output Current(A)|(% style="width:257px" %)0.01A|(% style="width:160px" %)◎|(% style="width:113px" %)D004
578 |=D0.05|IGBT Module Temperature（℃）|(% style="width:257px" %)0.1℃|(% style="width:160px" %)◎|(% style="width:113px" %)D005
579 |=D0.06|DI Input Status|(% style="width:257px" %)1|(% style="width:160px" %)◎|(% style="width:113px" %)D006
580 |=D0.07|DO Output Status|(% style="width:257px" %)1|(% style="width:160px" %)◎|(% style="width:113px" %)D007
581 |=D0.08|Keypad Knob Voltage|(% style="width:257px" %)0.01V|(% style="width:160px" %)◎|(% style="width:113px" %)D008
582 |=D0.09|AI Voltage(V)|(% style="width:257px" %)0.01V|(% style="width:160px" %)◎|(% style="width:113px" %)D009
583 |=D0.10|Reserved|(% style="width:257px" %)1|(% style="width:160px" %)◎|(% style="width:113px" %)D010
584 |=D0.13|PLC Stage|(% style="width:257px" %)1|(% style="width:160px" %)◎|(% style="width:113px" %)D013
585 |=D0.14|Feedback Speed(Unit0.1Hz)|(% style="width:257px" %)0.1Hz|(% style="width:160px" %)◎|(% style="width:113px" %)D014
586
587 == Error Records ==
588
589 |=(% scope="row" %)Parameter|=Name|=(% style="width: 429px;" %)Range and Description|=(% style="width: 124px;" %)Priority|=(% style="width: 129px;" %)Address
590 |=E0.00|Latest error type|(% style="width:429px" %)(((
591 * No Error: 0
592 * Acceleration Over Current: Err02
593 * Deceleration Over Current: Err03
594 * Over Current at constant speed: Err04
595 * Acceleration Over Voltage: Err05
596 * Deceleration Over Voltage: Err06
597 * Over Voltage at constant speed: Err07
598 * Low Voltage error: Err09
599 * VFD overload: Err10
600 * Motor overload: Err11
601 * IGBT overheat: Err14
602 * External Error: Err15
603 * Current Detection Error: Err18
604 * Parameter writing/reading error: Err21
605 * EEPROM writing/reading error: Err22
606 )))|(% style="width:124px" %)●|(% style="width:129px" %)　E000
607 |=E0.01|Running Frequency at latest error|(% style="width:429px" %)0.0Hz~~F0.05|(% style="width:124px" %)●|(% style="width:129px" %)　E001
608 |=E0.02|Output Current at latest error|(% style="width:429px" %)0.00~~655.35|(% style="width:124px" %)●|(% style="width:129px" %)　E002
609 |=E0.03|Bus Voltage at latest error|(% style="width:429px" %)0.0~~810|(% style="width:124px" %)●|(% style="width:129px" %)　E003
610 |=E0.04|Input terminals status at latest error|(% style="width:429px" %)0~~63|(% style="width:124px" %)●|(% style="width:129px" %)　E004
611 |=E0.05|IGBT temperature at latest error|(% style="width:429px" %)0~~65535|(% style="width:124px" %)●|(% style="width:129px" %)　E005
612 |=E1.00|Former error type|(% style="width:429px" %)As E0.00|(% style="width:124px" %)●|(% style="width:129px" %)　E100
613 |=E1.01|Running Frequency at former error|(% style="width:429px" %)0.0Hz~~F0.05|(% style="width:124px" %)●|(% style="width:129px" %)　E101
614 |=E1.02|Output Current at former error|(% style="width:429px" %)0.00~~655.35|(% style="width:124px" %)●|(% style="width:129px" %)　E102
615 |=E1.03|Bus Voltage at former error|(% style="width:429px" %)0.0~~810|(% style="width:124px" %)●|(% style="width:129px" %)　E103
616 |=E1.04|Input terminals status at former error|(% style="width:429px" %)0~~63|(% style="width:124px" %)●|(% style="width:129px" %)　E104
617 |=E1.05|IGBT temperature at former error|(% style="width:429px" %)0~~65535|(% style="width:124px" %)●|(% style="width:129px" %)　E105
618
619 = Communication Protocol =
620
621 VM Series AC Drive provides RS485 communication interface and supports Modbus communication protocol. Users can achieve centralized control by computer or PLC, set AC Drive operation commands, modify or read function code parameters, read the working state and fault info of the AC Drive.
622
623 == Communication Control Address ==
624
625 |=(% scope="row" style="width: 284px;" %)Function|=(% style="width: 134px;" %)Address|=(% style="width: 360px;" %)Description|=(% style="width: 276px;" %)Remarks|=Characteristic
626 |=(% style="width: 284px;" %)Communication Set Value|(% style="width:134px" %)1000H|(% style="width:360px" %)-10000～10000 (with ± sign)|(% style="width:276px" %)F0.05* (±100.00%)|R/W
627 |=(% rowspan="7" style="width: 284px;" %)Control Command|(% rowspan="7" style="width:134px" %)2000H|(% style="width:360px" %)0001: Forward running|(% style="width:276px" %)-|W
628 |(% scope="row" style="width:360px" %)0002: Reverse running|(% style="width:276px" %)-|W
629 |(% scope="row" style="width:360px" %)0003: JOG forward|(% style="width:276px" %)-|W
630 |(% scope="row" style="width:360px" %)0004: JOG reverse|(% style="width:276px" %)-|W
631 |(% scope="row" style="width:360px" %)0005: Free stop|(% style="width:276px" %)-|W
632 |(% scope="row" style="width:360px" %)0006: Deceleration stop|(% style="width:276px" %)-|W
633 |(% scope="row" style="width:360px" %)0007: Fault reset|(% style="width:276px" %)-|W
634 |=(% rowspan="3" style="width: 284px;" %)Running Status|(% rowspan="3" style="width:134px" %)3000H|(% style="width:360px" %)0001: FWD running|(% style="width:276px" %)-|R
635 |(% scope="row" style="width:360px" %)0002: REV running|(% style="width:276px" %)-|R
636 |(% scope="row" style="width:360px" %)0003: Stopped|(% style="width:276px" %)-|R
637 |=(% rowspan="11" style="width: 284px;" %)Monitoring Data|(% style="width:134px" %)1001H|(% style="width:360px" %)Running Frequency（Hz）|(% style="width:276px" %)2 decimal places|R
638 |(% scope="row" style="width:134px" %)1002H|(% style="width:360px" %)Set Frequency（Hz）|(% style="width:276px" %)2 decimal places|R
639 |(% scope="row" style="width:134px" %)1003H|(% style="width:360px" %)Bus Voltage（V）|(% style="width:276px" %)1 decimal place|R
640 |(% scope="row" style="width:134px" %)1004H|(% style="width:360px" %)Output Voltage（V）|(% style="width:276px" %)1 decimal place|R
641 |(% scope="row" style="width:134px" %)1005H|(% style="width:360px" %)Output Current（A）|(% style="width:276px" %)2 decimal places|R
642 |(% scope="row" style="width:134px" %)1006H|(% style="width:360px" %)IGBT Temperature|(% style="width:276px" %)1 decimal place|R
643 |(% scope="row" style="width:134px" %)1007H|(% style="width:360px" %)Digital input status|(% style="width:276px" %)DI1-DI4 Added by binary bit weight|R
644 |(% scope="row" style="width:134px" %)1009H|(% style="width:360px" %)Keypad Knob Voltage（V）|(% style="width:276px" %)1 decimal place|R
645 |(% scope="row" style="width:134px" %)101AH|(% style="width:360px" %)AI Volatage （V）|(% style="width:276px" %)1 decimal place|R
646 |(% scope="row" style="width:134px" %)100BH|(% style="width:360px" %)Load Speed Display|(% style="width:276px" %)1 decimal place|R
647 |(% scope="row" style="width:134px" %)100EH|(% style="width:360px" %)PLC Stage|(% style="width:276px" %)Simple PLC running stage|R
648 |=(% rowspan="14" style="width: 284px;" %)Failure status|(% rowspan="14" style="width:134px" %)8000H|(% style="width:360px" %)0000: No error|(% style="width:276px" %)-|R
649 |(% scope="row" style="width:360px" %)0002: Acceleration Over Current|(% style="width:276px" %)-|R
650 |(% scope="row" style="width:360px" %)0003: Acceleration Over Current|(% style="width:276px" %)-|R
651 |(% scope="row" style="width:360px" %)0004: Over Current at Constant Speed|(% style="width:276px" %)-|R
652 |(% scope="row" style="width:360px" %)0005: Acceleration Over Voltage|(% style="width:276px" %)-|R
653 |(% scope="row" style="width:360px" %)0006: Deceleration Over Voltage|(% style="width:276px" %)-|R
654 |(% scope="row" style="width:360px" %)0007: Over Voltage at Constant Speed|(% style="width:276px" %)-|R
655 |(% scope="row" style="width:360px" %)0009: Low Voltage Error|(% style="width:276px" %)-|R
656 |(% scope="row" style="width:360px" %)000A: VFD Overload|(% style="width:276px" %)-|R
657 |(% scope="row" style="width:360px" %)000B: Motor Overload|(% style="width:276px" %)-|R
658 |(% scope="row" style="width:360px" %)000E: IGBT Overheat|(% style="width:276px" %)-|R
659 |(% scope="row" style="width:360px" %)000F: External Error|(% style="width:276px" %)-|R
660 |(% scope="row" style="width:360px" %)0012: Current Detection Error|(% style="width:276px" %)-|R
661 |(% scope="row" style="width:360px" %)0015: Parameters Writing/Reading Error|(% style="width:276px" %)-|R
662 |=(% rowspan="9" style="width: 284px;" %)Communication Error Feedback|(% rowspan="9" style="width:134px" %)8001H|(% style="width:360px" %)0000: No Error|(% style="width:276px" %)-|R
663 |(% scope="row" style="width:360px" %)0001: Password Error|(% style="width:276px" %)-|R
664 |(% scope="row" style="width:360px" %)0002: Command Code Error|(% style="width:276px" %)-|R
665 |(% scope="row" style="width:360px" %)0003: CRCError|(% style="width:276px" %)-|R
666 |(% scope="row" style="width:360px" %)0004: Invalid Address|(% style="width:276px" %)-|R
667 |(% scope="row" style="width:360px" %)0005: Invalid Parameter|(% style="width:276px" %)-|R
668 |(% scope="row" style="width:360px" %)0006: Parameters Adjustment Failed|(% style="width:276px" %)-|R
669 |(% scope="row" style="width:360px" %)0007: System Locked|(% style="width:276px" %)-|R
670 |(% scope="row" style="width:360px" %)0008: Parameters Being Saved|(% style="width:276px" %)-|R
671
672 Sheet 5-1-1 Control Command Addresses
673
674 == EEPROM Addresses Introduction ==
675
676 The addresses listed in the sheet above is the way of writing RAM. The RAM stores the data after power-off and does not save it. In the communication mode, for the write command "06H", if the parameter needs to be stored after power-off, the method of writing EEPROM should be used. The original "0" of the most significant bit of the RAM address is changed to "F", which is converted into the corresponding EEPROM address, for example: "0XXX" is changed to "FXXX"
677
678 Example of address conversion: Upper limit frequency F006, write RAM communication address: 0006, corresponding EEPROM address: F006.
679
680 Acceleration time F010, the communication address for writing RAM is: 000A, and the corresponding address for EEPROM is: F00A.
681
682 Other parameters, are like that...
683
684 It should be noted that the erasing life of EEPROM is about 1 million times. After exceeding the erasing times, it will affect the reliability of data storage. If it is not necessary, it is recommended to control the communication by writing to RAM.
685
686 = Troubleshooting & countermeasures =
687
688 == Faults and solutions ==
689
690 |=(% scope="row" %)Fault code|=Fault type|=Reason|=Solution
691 |=Err02|Overcurrent during acceleration|(((
692 ~1. The output circuit of AC Drive is grounded or short circuited.
693
694 2. The acceleration time is too short.
695
696 3. The startup operation is performed on the rotating motor.
697
698 4. The AC Drive model is of too small power.
699 )))|(((
700 ~1. Eliminate external faults.
701
702 2. Increase the acceleration time.
703
704 3. Select rotational speed tracking restart or start the motor after it stops.
705
706 4. Select the AC Drive of higher power.
707 )))
708 |=Err03|Overcurrent during deceleration|(((
709 ~1. The output circuit of AC Drive is grounded or short circuited.
710
711 2. The deceleration time is too short.
712 )))|(((
713 ~1. Eliminate external faults.
714
715 2. Increase the deceleration time.
716 )))
717 |=Err04|Overcurrent at constant speed|(((
718 ~1. The output circuit of AC Drive is grounded or short circuited.
719
720 2. The AC Drive model is of too small power.
721 )))|(((
722 ~1. Eliminate external faults.
723
724 2. Select the AC Drive of higher power.
725 )))
726 |=Err05|Overvoltage during acceleration|(((
727 ~1. Input voltage abnormal.
728
729 2. An external force drives the motor during acceleration.
730
731 3. The acceleration time is too short.
732
733 4. The braking unit and braking resistor are not installed.
734 )))|(((
735 ~1. Turn the input power to the normal range.
736
737 2. Cancel the external force.
738
739 3. Increase the acceleration time.
740
741 4. Installed the braking unit and braking resistor.
742 )))
743 |=Err06|Overvoltage during deceleration|(((
744 ~1. Input voltage abnormal.
745
746 2. An external force drives the motor during deceleration.
747
748 3. The deceleration time is too short.
749
750 4. The braking unit and braking resistor are not installed.
751 )))|(((
752 ~1. Turn the input power to the normal range.
753
754 2. Cancel the external force.
755
756 3. Increase the deceleration time.
757
758 4. Installed the braking unit and braking resistor.
759 )))
760 |=Err07|Overvoltage at constant speed|(((
761 ~1. Input voltage abnormal.
762
763 2. An external force drives the motor during deceleration.
764 )))|(((
765 ~1. Turn the input power to the normal range.
766
767 2. Cancel the external force.
768 )))
769 |=Err09|Undervoltage|(((
770 ~1. Instantaneous power failure occurs on the input supply.
771
772 2. The input voltage is not within the normal range.
773
774 3. The AC Drive has an abnormality.
775 )))|(((
776 ~1. Reset the fault.
777
778 2. Adjust the input voltage to normal range.
779
780 3. Looking for technical service.
781 )))
782 |=Err10|AC Drive overload|(((
783 ~1. The load is too heavy or lockedrotor occurs on motor.
784
785 2. The AC Drive model is of too small power.
786 )))|(((
787 ~1. Reduce the load and check the motor.
788
789 2. Select the AC Drive of higher power.
790 )))
791 |=Err11|Motor overload|(((
792 The parameter setting of F2.03 does not match the motor
793
794 2. The AC Drive model is of too small power.
795 )))|(((
796 ~1. Set this parameter correctly.
797
798 2. Reduce the load and check the motor.
799 )))
800 |=Err14|Module overheating|(((
801 ~1. The ambient temperature is too high.
802
803 2. The air filter is blocked.
804
805 3. The fan is damaged.
806
807 4. The IGBT is damaged.
808 )))|(((
809 ~1. Lower the ambient temperature.
810
811 2. Clean the air filter.
812
813 3. Replace the fan.
814
815 4. Ask for technical service.
816 )))
817 |=Err15|External equipment fault|External fault signal (DI) triggers|1. Check the input DI terminal
818 |=Err16|Communication fault|(((
819 ~1. The PC is in abnormal state.
820
821 2. The communication cable is faulty.
822
823 3. The communication parameters of FC group are set improperly.
824 )))|(((
825 ~1. Check the cabling of the PC.
826
827 2. Check the communication cabling.
828
829 3. Set the communication parameters properly.
830 )))
831 |=Err18|Current detection fault|(((
832 ~1. Current detection circuit is abnormal.
833
834 2. Control circuit is abnormal.
835 )))|1. Ask for technical service.
836 |=Err21|Data overflow|1. The control board is abnormal.|1. Ask for technical service.
837 |=Err22|On-power EEPROM check fault|1. The EEPROM chip is damaged.|1. Ask for technical service.
838
839 Table 6-1-1 Faults and solutions
840
841 == Common faults and solutions ==
842
843 |=(% scope="row" style="width: 59px;" %)**SN**|=(% style="width: 232px;" %)**Fault**|=(% style="width: 437px;" %)**Possible causes**|=(% style="width: 475px;" %)**Solutions**
844 |=(% style="width: 59px;" %)1|(% style="width:232px" %)No display at power-on state|(% style="width:437px" %)(((
845 ~1. The input power of AC Drive is abnormal.
846
847 2. The control board has a bad contact with cable that is connected to the keypad.
848
849 3. The AC Drive is abnormal.
850 )))|(% style="width:475px" %)(((
851 ~1. Check the input power.
852
853 2. Re-connect the cable.
854
855 3. Ask for technical service.
856 )))
857 |=(% style="width: 59px;" %)2|(% style="width:232px" %)The motor does not rotate after the AC Drive runs.|(% style="width:437px" %)(((
858 ~1. The motor is damaged.
859
860 2. The motor cables is abnormal.
861
862 3. The cable between the drive board and control board is in poor contact.
863
864 4. The AC Drive is abnormal.
865 )))|(% style="width:475px" %)(((
866 ~1. Replay the motor.
867
868 2. Ensure the cable between the AC Drive and the motor is normal.
869
870 3. Check the cable between the drive board and control board.
871
872 4. Ask for technical service.
873 )))
874 |=(% style="width: 59px;" %)3|(% style="width:232px" %)DI termianls are disabled.|(% style="width:437px" %)(((
875 ~1. The parameters are set incorrectly.
876
877 2. The external signal is incorrect.
878
879 3. The control board is abnormal.
880 )))|(% style="width:475px" %)(((
881 ~1. Check and reset the parameters in group F5.
882
883 2. Re-connect the external signal cables.
884
885 3. Ask for technical service.
886 )))
887 |=(% style="width: 59px;" %)4|(% style="width:232px" %)AC Drive interference|(% style="width:437px" %)(((
888 ~1. Carrier frequency setting is not suitable.
889
890 2. The grounding method of the AC Drive and the motor is incorrect.
891
892 3. The wire between the AC Drive and the motor is too long.
893 )))|(% style="width:475px" %)(((
894 ~1. Reduce the carrier frequency
895
896 2. The AC Drive and the motor are effectively grounded and separated from the ground of the peripheral device.
897
898 3. Install out reactor or reduce wire distance.
899 )))
900 |=(% style="width: 59px;" %)5|(% style="width:232px" %)Motor noise is too loud.|(% style="width:437px" %)(((
901 ~1. Motor damage or mechanical failure.
902
903 2. Carrier frequency setting is too small.
904 )))|(% style="width:475px" %)(((
905 ~1. Replace the motor or clear the mechanical fault.
906
907 2. Increase the carrier frequency appropriately.
908 )))
909 |=(% style="width: 59px;" %)6|(% style="width:232px" %)Switch trip|(% style="width:437px" %)(((
910 ~1. Installed a leakage switch or an air switch overload.
911
912 2. The input power of AC Drive is abnormal.
913
914 3. The AC Drive is damaged.
915 )))|(% style="width:475px" %)(((
916 ~1. Replay the leakage switch or replay the larfer capacity air switch.
917
918 2. Eliminate whether the input power is shorted.
919
920 3. Ask for technical service.
921 )))
922
923 Table 6-2-1 Common faults and solutions